GTW460ASJWW washing one mop head, GE top load washer
Dennis Miracle wanted me to wash a mop head in this washer and went through the trouble of shipping to me. I understand his concerns after filming with this video. Some machines can handle an unbalanced load better than others. I would try to avoid loading machine knowing that it will be unbalanced. Thanks again to Mr. Miracle for sending the mop head.
More about the washer:
www.applianceofaustin.com/pro...
Пікірлер: 250
1:16 Load 3:14 Start 3:25 Fill 12:42 Wash 24:43 Low Wash 27:42 Low Wash Stop 27:45 Lid Locks 27:56 Drain 29:58 Drain Stops 30:23 Low Spin And Out Of Balance 31:56 Medium Spin Out Of Balance Again 32:53 Medium Spin Stops 33:19 Rinse Fill 42:50 Rinse 45:50 Rinse Stops 45:54 Lid Locks 46:05 Drain 48:08 Drain Stops 48:28 Drain Start 48:33 Low Spin And Out Of Balance 50:04 High Spin, Out Of Balance And Returns To Low Spin 51:40 High Spin And Out Of Balance 1:00:34 Spin Stops 1:01:57 Drain Starts 1:02:02 Cycles Done
@anndinh10
Ай бұрын
Short: 3:14 Start 3:25 Fill 12:42 Wash 27:56 Drain 30:23 Low Spin And Out Of Balance 31:56 Medium Spin Out Of Balance Again Rinse Fill 42:50 Rinse 46:05 Drain 48:33 Low Spin And Out Of Balance 50:04 High Spin, Out Of Balance And Returns To Low Spin 51:43 High Spin And Out Of Balance 1:02:02 Cycles Done
I've had this machine for 14 months now. Prior to it we had a new Maytag Bravos (plate style agitator) which was two years old. The Maytag replaced a 23 year old Kenmore. The Maytag was fine except it took about an hour and a quarter for one load, thus we bought this GE. Now, the GE is by no means our old Kenmore, but as far as newer washers go, we have been very happy with it and it does several loads a week. The first thing I did was bought the part on the lid that goes into the lid lock hole. That way, I can put the spare part in and it will operate with the lid up. One thing that I have learned is that the water level will vary depending on the cycle. For example, When set on Super water level, it will fill to the fullest on heavy white cycle, fills to just over top holes. Other cycles Super water level will fill tub to 2 holes to three holes down. Also, on any cycle besides white heavy, I will pour a gallon of water on the load before starting and any cycle will go to the top holes on Super water level. I've only done this a couple of times so it's not like a lot of work. Most times I just set the cycle and go. The only issue I have had with the machine is that it does overbalance easy. But I do just as another poster suggested and put in an extra towel or something to balance it. Speaking of balance... I have often wondered why the modern washers don't have an overbalance signal? Washers of old (My old Kenmore) would cut off if it got overbalanced and an overbalance light would flash. Some models also had a buzzer that would sound. Honestly, I haven't seen any of the modern washers that are worth squat with the possible exception of Speed Queen, but as for what is available, I have been very happy with this GE. It does clean the clothes very well and in a reasonable amount of time. When we decided to replace the Maytag, we were considering Speed Queen but a big ruckus started about their 2018 models which were far inferior to anything prior to it because of some changes they made and the reviews were awful, so we bypassed SQ. I've been told Speed Queen fixed some of the bad 2018 changes but I haven't followed up.
@apAvocado
3 жыл бұрын
Not to mention that Speed Queen prices have gone over $1200. I paid about $750 in 2013. Not paying $1200 in January 2021. My Speed Queen died this week - 7 years of service. Today's washers are nothing like the workhorses of the 1970s.
After all these years, buddy, I still appreciate you running this cycle with the mop for me. Blessings to you.
@DemonPlaysYt6
20 күн бұрын
❤❤❤
I have a Maytag washer that I bought 3 1/2 years ago. I HATE it. I have talked to Lowes, sent emails to Maytag corporate along with pictures of clothing that will NOT come clean, tried soaking in the machine (that's laughable....even on what they call "SOAK" some of the clothing comes out with dry streaks), using gallons of SprayNWash, spending so MUCH time on laundry!! Laundry used to be one of my easiest household tasks. Just put in the detergent and wash the clothes. I would give anything to have my first washing machine (which was a Maytag!) I had it for 20 + years and it washed an average of 2-3 loads a day with 3 boys playing sports. If only I could have looked into the future and seen what was coming. I would have had it repaired and completely refurbished and used it another 20 years!
I had a GE washer for over 11.5 years. It NEVER got out of balance. It was by far the best washer I ever owned. I purchased a new GE 4.5 cu ft washer in June of 2021. The. Agitator fell off during a load of clothes. It definitely has balance issues. It also vibrates greatly when it starts to spin. Not the best washer. Not sure they make many good washers like they used to.
No wonder these things break after a violent spin cycle. You can't win for losing with these washers no matter what brand you get.
My GE that is 5 years old sounds like a freight train on the spin cycle. Also occasionally it won’t do a real spin. When it spins properly my clothes are super wrinkled that I have to iron them. Ugh. I’m looking for a new one and I’m a little scared of buying a GE. So thanks for the video. Very informative.
@condor5635
4 жыл бұрын
Bearing is bad more than likely. I did a video on replacing it.
Hi need info on a GE washer GTW she starts filling then stops then open the lid close it and starts back to fill then stops again open lid again and close it and starts to continue filling again what could caise that
Glad I went with the speed queen. Runs nice and quiet. Clean clothes in under 40 minutes.
I am considering buying this washer and read the reviews that it was noisy and was concerned. I wished there was a way I could see it go through a full cycle and never expected to find something like this. Thank you for taking the time to video this. Although I am one of the few people to leave a comment about how it helped me as a consumer, I am sure this has helped many many other people in making their decision on which washer to buy.
@kirkrivas8172
7 жыл бұрын
StPeterRabbit comments like yours gives me the energy to do more videos, I really appreciate your comment.
@StPeterRabbit
7 жыл бұрын
Decided on speed queen AWN432SP113TW04. It seems to blow all of the top load washers with agitator away by far. I have done hours and hours of research and came to this conclusion, unless anyone can say different.
@kirkrivas8172
7 жыл бұрын
Nice choice! There is a very large group of people that feel the same. Thanks for your comments, keep us posted on your new washer.
@kenkubler2059
6 жыл бұрын
I have this washing machine, worst $600 piece of junk I ever got ripped off for
@peterjohnson7710
6 жыл бұрын
Speed Queen washer are the only washers still make like they were is the 1960's . They're tougher than any other washer on the market . You have rocks in you head if you buy another brand new washer brand other than Speed Queen .
The Speed Queen TR SERIES have like a partial neutral drain. 4 or 5 inches of water go down first,then a spin to the left,pause,and then spins clockwise the first spin having a 45 second spray rinse before reaching full spin speed. If a second rinse option selected you'll also get another spray rinses before filling up for another tub rinse.
GREAT VIDEO !!! . i have the same washer . but the water level you got washing the mop head is not what i get . I have followed instructions and still deep fill sucks . i purchased this model because the larger tub . thinking i could wash larger loads . big mistake . i don't get why such large tubs when they don't fill to the top for larger loads . thanks for sharing .
I give this video 4.5 stars out of 5. I liked it very much the only thing missing was to show the noise level during wash with the lid closed at 1 foot range, 5 feet, 10 etc.Based on this video I am considering this GE model, I love the fact that you are a user select the water level the old fashion way as before vs this new crap today LOAD SENSE, it start agitating to determine the load size and it the mean time is moves clothes around with minimum water, as an engineer where is LOGIC here in people who came up with stupid feature.
@kirkrivas8172
6 жыл бұрын
Thanks for your comment. This washer seems like a decent machine.
Kirk, quick question please? :) what’s the difference between this model with electrical panel VS the manual panel model? And does either machine buzz when cycle is completed? I don’t see a buzz/no buzz setting on the panel... thank you in advance!!
@kirkrivas8172
6 жыл бұрын
I do not remember if they buzz or not.. The manual panel is the electrical panel in disguise. I believe the knob is attached to the control panel. I'll check. Do you remember the model number to the other machine?
I almost got under my desk while it was spinning, LOL
@strongclassicsonic8468
3 жыл бұрын
I see why
@JrGonzalez-pn2or
19 күн бұрын
😮💢💢💢💢🤬🤬🤬👎👎👎👎👎👎
@JrGonzalez-pn2or
2 күн бұрын
@@strongclassicsonic8468🤣
How come on this model the agitator only spins in one direction every other rotation? How come it doesn’t agitate in both directions everytime like the slightly cheaper model that doesn’t have the extra options and auto soak? Not sure if it’s better this way or the other way, to me it seems like a pretty obvious answer that it’s better for it to agitate both ways.
Hey kirk. Happy New Year! I'd like to see the gtw500 in action.
Awesome vid. If you still have the mop head, I'd be interested in seeing how the whirlpool handles the unbalanced spin. Thanks!
@kirkrivas8172
7 жыл бұрын
I will put it on the list. I'm curious too!
@Cooldude84343
7 жыл бұрын
This machine did handle it better than I expected, and like you I was a bit scared when the tub was like lifting up to the top cabinet! Not sure if its a feature on this machine or not but I'm surprised it didn't try to do some kind of auto balance correction, like a partial refill and agitate like some models do. Maybe its the whirlpool that does that I'm not sure.
my dad and stepmom have a machine from this line, but theirs has a slanted vane instead of a corkscrew type agitator
I have this machine & love it. Works great
We purchased this Maytag MVW7230Hw washer from Pochel’s in Tacoma, Washington. It was delivered and set up by the delivery person. We tried to do a load of laundry and the washer wouldn’t agitate. I took a video to show that the agitator pretty much just vibrated, and didn’t even disturb the small amount of suds that formed when the machine partially filled with water. I took the video to Pochels the next morning. They said they would gladly deliver another machine for only $100. I told them I wasn’t willing to pay an additional $100 to get a machine that worked when I had already paid over $1,000 for one that obviously didn’t work. The agitator doesn’t always work, the fill doesn’t always work, the agitator tries to dry clean the clothes with no water in the tub and the clothes on top don’t get clean.
@Mighty-the-Armadillo419
2 жыл бұрын
Idiot, this is not a Maytag, this is a GE. Nice storyline tho
Aye what cycle is happening @24:43 with the pause,..start,...pause.
can I have the step after the process of draining and spinning.
Very helpful, thank you
@kirkrivas8172
2 жыл бұрын
You're welcome!
All I know is. I'm glad that i spent the money that I did on my "Speed Queen" None of these issues with the Speed Queen as far an out of balance load because it spins everything out no matter how light or heavy the load is and besides I could have washed that Mop Head on a low water setting using the heavy duty cycle and taking only 38 minutes to complete......
@apAvocado
3 жыл бұрын
@@tmr8193 My Speed Queen lasted 7 years. It took a lot of laundry loads. It ran like a champ! But I guess it had had enough with so many 12 hour washing days. It rusted out completely, motor oil draining, and water leaking out onto the floor. Never used fabric softener. Just detergent. Did clean it with Affresh. I don't know what happened. I guess it was just TOO MUCH laundry. Plus it was a 3.2 cu ft capacity. I guess too small for a family of 6.
I have this washer. It washes everything great. I do have problems when I wash a couple of quilts. It gets out of balance when it spins.
@ApplianceRep
5 жыл бұрын
Gary Clark kzread.info/dash/bejne/eISimsawpZicZMo.html
@kellybills9641
5 жыл бұрын
Gary Clark just wait it will fall apart guaranteed!
@garyclark9807
5 жыл бұрын
Kelly Bills you are probably right. My mom has a Maytag bravo it’s only 2 years old and it’s falling apart. It gets out of balance easily too.
@garyclark9807
5 жыл бұрын
I found out if you lay the quilts around the edge and overlap them so it’s balanced when you lay them around, it works ok.
@kellybills9641
5 жыл бұрын
@@garyclark9807 I wish that was the only problem. At 9 months they replaced the lid switch & it wasn't 4 months & it started not working again. I just fixed it, I unscrewed the part on the lid and put it in the lock. Now that sucker will work. It is also starting to leak & it isn't even 3 yrs old. It also randomly decides to not drain and spin correctly and the clothes are sopping wet. I'm trying to get a bunch of people to band together to write and/or call GE. Look me up on Facebook and pm me or post on my wall if you're interested. Kelly McDowell Bills, Springfield, Missouri. Hope you have better luck, but color me skeptical!
Strange, the machine doesn't drain while spinning? 46:50 Gosh that machine shakes like CRAZY!
@ericxxonvf
3 жыл бұрын
@Chelsea Menges The speed queen does
can you do a video of the new GE(General Electric) top load washer with see through lid and Dual action agitator, model number gtw685bslws?
@kirkrivas8172
7 жыл бұрын
I just ordered another one today from GE, should be here soon. I will film it as soon as I get my hands on it!
I actually have this exact model number. Because it ripped my clothing, I am going to return it. Do you have any suggestions before I exchange it?
@thomaskeets3194
5 жыл бұрын
Electrolux EFLS627UTT
How does it still go without the lid being shut ? I have the same washer and mine pauses when I open the lid. And I hate it so much .
@Smurdle450
2 жыл бұрын
The lid switch was bypassed.
I got the same washer it does not fill properly I put the cloths in select water level and we'll a medium to large load gets small water level. . I have to fill it by a bucket at times..
@kirkrivas8172
5 жыл бұрын
Water pressure impacts the water level for this particular washer. I have cut water pressure on this washer and noticed this machine will start to wash with hardly any water in the the tub. Most electronic washers will through an error code if you have low water pressure. This machine has a pressure switch but is probably used for safety (over flow reasons).
Lot of water for this mop!?
I'm thinking about going back to a older model iv always had Kenmore until I got this...
Thank you so much for all these GE videos. You have really helped me decide which machine I want to replace my old school Kenmore. Is it possible to just run a rinse and spin cycle with this machine and the 330 as well. I like to hand wash some items and then give them a quick spin if I'm in a hurry. Also what is the difference between the "deep fill" button and the "deep rinse" button on the two different models. Are they the same, but with different names and if I don't push it will I just get a spray rinse instead of the tub filling? Thanks again for all these awesome videos. I can't believe they exist. They answered so many questions.
@kirkrivas8172
6 жыл бұрын
I have not forgotten about your questions... I will try to answer them shortly.
@vickiglenn2527
6 жыл бұрын
Thanks for getting back so quickly. Take your time. You're a busy guy running your own business and helping a bunch of youtubers on the side. I actually watched your water level test on the 330 after posting my question. We only have 5 PSI because we are on gravity feed. The manual I found online says the machine needs a minimum of 20 PSI. (The manual helped me understand the deep fill and deep rinse buttons too and another commentor mentioned using only the spin cycle so I guess the machine does that.) Hopefully, we can figure out how to run a pump to the new GE machine machine, but I might have to stick with my old Kenmore. I have a new question now too. The clutch broke a few weeks ago on the Kenmore. We replaced it, but it still isn't completely up to speed in the spin cycle. I am wondering if the basket drive was over stressed too. It runs well enough, but will I blow out the transmission running it with a worn basket drive or worn drive block. Thanks. I really appreciate your time. You deserve some kind of humanitarian award for helping explain this stuff to people before they invest $ on these expensive machines.
@kirkrivas8172
6 жыл бұрын
This machine will start washing even if there is not enough water in the tub due to low water pressure. Old school machines will start washing when the water level pressure switch was satisfied even it it took 24 hours to fill the tub. The new machines will give an error code if the the machine takes too long to fill. This machine does something I have never seen before. Instead of giving an error code, it starts to wash after a designated time. So I would not buy one if you have low water pressure. Deep rinse is used for rinses with a full tank of water, usually about 3/4 of a tank. Rinse with fabric softener is code for deep rinse on most machines, mostly used for those wanting to rinse their clothes properly. If you do not select deep rinse or rinse with fabric softener then the machine will do a spray rinse to simulate a full rinse. I am not sure what the difference is between the water level set for high and deep fill. I would use deep fill to be on the safe side. On your Kenmore, the basket drive may need to be replaced.
@vickiglenn2527
6 жыл бұрын
Thanks for your help
I want to see an LG front load washer in action.
Was this on gentle cycle?
I have a Kenmore 110.26132413 and I have never seen that much water in the tub unless I had it set to deep fill......definitely no on a small load! I want more water! High efficiency shouldn't mean "almost no water" per load!
@randomstarlexlo
9 ай бұрын
Nice man!
Do you use this mop head in your business? How dirty does it get?
You also definitely need to fix the drum springs
I purchased this exact washing machine 3 months ago at Lowes after seeing the video showing the DEEP FILL option thinking it would be a great machine. It easily goes out of balance constantly. If you wash a set of sheets they are always in a big tight knot. I miss my old top loading Kenmore. I would NOT recommend this washer.
@judyalberts351
5 жыл бұрын
Anna Labick yes it’s a HORRIBLE machine mine is a New Pieces of Crap too 💩 Only puts 3 gallons water clothes don’t even get wet and in a big knot also now their ripping GE lies and excuses are unreal the Refuse to fix or Replace I’d NOT recommend this model or ANY of GE’s crap 💩 .....
That rally got ballance at the spin cycle
Can you wash a mop head in a eletrouk
I thought high efficiency washing machine supposed to detect off balance
Should i get this washer or the GTW330ASKWW?
@NYCcat
5 жыл бұрын
Steer clear of GE completely...Worst appliances when it comes to washers ever. Don't believe me, keep reading the reviews. Good luck.
kirk rivas do the deep washy on the lg top washer
Do some tutorials on the GE GTW485ASJWS Please💪.
@ApplianceRep
5 жыл бұрын
1_Swole_Nole kzread.info/dash/bejne/eISimsawpZicZMo.html
How about was 2 bed pillows ??????
I also bought the same washer u are showing in your video & it doesn't fill to the top. I did exactly what u did in 2 videos & it still doesn't fill to the top. Help please...
@kirkrivas8172
7 жыл бұрын
I'm not sure on this model, but other GE units water flowing in the tub will impact the final water level. Make sure you have adequate flow by comparing to the video and try the warm water setting to allow max flow rate. These models have been around for a while and may have changed specification in the middle of production. How long have you had this unit?
@nosmile73
7 жыл бұрын
Kirk Rivas I bought this washer a week ago, its a GE washer model number: GTW460ASJ6WW. The same one you use in your videos.
@kirkrivas8172
7 жыл бұрын
I would call factory service at 1-800-GE CARES, and ask them to check it out. Please understand that some servicers may try to collect money from you if it is not factory problem. But, you should be able to argue the point because it is so new. You may want to experiment with different cycles and make sure the deep feel is selected.
@nosmile73
7 жыл бұрын
Kirk Rivas Thank you for your time & info. I'm going to look into & see what happens.
@ljohn1999
6 жыл бұрын
I read some where that the person called GE and they told them to unplug it then plug back in and that should do it and they said that was unacceptable and returned the machine. I do not own one so I don't know but been watching tons of video's trying to decide on a washer.
Why did you put so much water in it? just over the top of the mop would have been sufficient and we could have seen the action better.
How fast is the final spin RPM’S
@texasabbott
3 жыл бұрын
800 rpm and very noisy as most cycles go to full speed. The basket is quite large so the wall speed is very fast and you will end up peeling the clothes off the basket walls.
@mustangdbest220
3 жыл бұрын
@@texasabbott thats kind of slow also will not rip the clothes because we have an LG top loader and the extra high spin goes 1,100 RPM and its quite and smooth its a 4.9 cf
How can you test all this washers avoiding the lid lock?
@kirkrivas8172
7 жыл бұрын
I work with a bunch of service technicians who know how to circumvent the problem. :)
@BydavidYT
6 жыл бұрын
TO GE
@doctorfeinstone6524
6 жыл бұрын
Take the latch off the lid and put it in the lid lock hole. Then it will think the lid is closed. It's easy
51:40 I think it cracked 😂😂🤣🤣 also 50:04 😂😂😂 and 31:56 how did it not get an error code 💀💀 30:23 she’s scared!😱 50:36 she is puking
what's with business cards all over the place? also why wouldnt you wash a dirty mop head vs a clean one?
@kirkrivas8172
6 жыл бұрын
I don't know what I was thinking. At that time, I really did not want to foul up the machine with a dirty mop head, I was trying to keep the washer clean. I'm not as careful these days, I may wash a dirty one.
What is difference in these two model numbers: Compare GTW460ASJWW GTW460ASJ5WW
👍👍👍
45:50 why thing took out? 48:28
U dont need super load, U don't need deep fill, U don't need fabric softener mode. The 1 mop head makes the machine unbalanced. I'm just want to know about rince cycle work. I do Janitorial work, I wash all my Mop heads together so it won't be unbalanced... How did U keep the lid opened ??
@renders_universe
11 ай бұрын
“How did U keep the lid open.” Lid Lock Bypass.
The way that its spins with the hole 48:55
2k and go's crazy
Why would you need to use "deep fill" if the load size is is set to "super"?
@kirkrivas8172
6 жыл бұрын
It sounds redundant, I need to hook it up again and find out why they did that. I'll look into it.
That washer was crazy unbalanced with the mop head!
I've owned this machine for about six months and have decided to get rid of it for this very reason. It is POOR at handling unbalanced loads. It vibrates out of place and I periodically have to reposition the washer. It is just LOUD too. I wanted to go with the new SQ because of previous ownership experience but after reading and watching reviews of it I've opted for the Maytag Commercial style top loader. I haven't yet received it. I hope it was a good purchase decision!
@lt38217
5 жыл бұрын
I'm in between this GE set & the Maytag commercial.....how's your Maytag been so far?
31:57 geez my god
51:44 Whoa Whoa Whoa!!!!
mine will not fill to the top.
@kirkrivas8172
7 жыл бұрын
Bridget Love, be sure you have a heavy duty cycle or bulky items selected with load size set to max with the deep fill option selected. Also use the rinse for fabric softener option. If water is coming in too slow, then it may start washing without the necessary water. Do you have the same model?
@BriNG384
7 жыл бұрын
Kirk Rivas thanks. No i have the GTW485ASJWS
@kirkrivas8172
7 жыл бұрын
Bridget Love, I'll look up the capabilities of that unit.
@kirkrivas8172
7 жыл бұрын
Bridget Love, it should be able to fill with the bulky setting cycle and deep fill option selected.
@BriNG384
7 жыл бұрын
Kirk Rivas yes I already tryed that, but still fills up less than half way. Just bought it yesterday, i think im just gonna switch it out for a different one. But thanks for your time.
50:05 going off balance
Yes
48:35 Petty Unbalaced!
On the wash cycle it is the same as spin cycle! but the spin cycle is different.
We have that washer
mine washing but not draining or spinning
@kirkrivas8172
6 жыл бұрын
Sorry to hear about the problem, It could be the lid lock mechanism. I think for factory authorized service you can call 1-800-GE-CARES.
It took over 12 minutes to fill.
You didn't put in Powder or Liqurid
30:25 Its obvious it has the 4 rod suspension system XD
Why are you filling the washer ALL the way up ? Wouldn't you put it on small wash?
no detergent added??????
This would be better with ACTUAL tub suspension, but it isn't added because of... COST CUTTING!!!
Do it with the hotpoint and the ge with the same mop head
Sounds like a helicopter while the spin looks unbalanced
My old apartment's washer
This is like a movie, the washer takes too long .
A front loader reflects the intelligence of the user!
Oi tudo bem
I have a new ge Washer
oh my dear lord 31:57
🎉.
I'd love to see the new GE profile ultra fast combo on the normal cycle with both wash and dry, along with laundry detergent and fabric softener.
Hi
and holy crap 50:07
2 month s work only maytag
30:23 31:55 48:34 50:05 51:42 all the times when the washer got unbalanced And plus in 32:30 and 1:00:00 the spin cycle was crazy unbalanced
@denster1964
3 жыл бұрын
Yeah. I would not recommend a washer that doesn’t detect an out of balance load. In this case, a smart washer, such as LG, would be better in this unbalanced situation. I get notified when mine is unbalanced, however that happened only once.
@Americas_Channel
Жыл бұрын
Well this here washing machine needs to learn to reach its balance
30:23 31:55 48:34 50:05 51:42 32:30 1:00:00
30:38
30:38 Quality Pump noises ;3;
You need to fix the agitator the teeth are not connecting so it slips sometimes that’s why you hear the motor but some times it doesn’t spin
Edge speed max: 50 mph
GE should be letting Whirlpool make their appliances.
@albertcarello619
Жыл бұрын
CrestwoodRocks: I certainly thought that they did for quite some time since there's dual agitation action models and neutral draining like Whirlpool. I thought that maybe GE merged with Whirlpool.
@CrestwoodRocks
Жыл бұрын
@@albertcarello619 It seems like they partially have over the years Whirlpool did made GE Spacemaker Washer. RCA is also a General Electric product but Whirlpool had RCA for a period of time. Whirlpool does make Hotpoint overseas while GE makes Hotpoint in the United States.
This machine is a water Hog!
@ravenspe
6 жыл бұрын
He purposely chose the settings that use the most water. Having that option is a wonderful thing.
do one with clothes pls
@kirkrivas8172
7 жыл бұрын
Try looking at this, I need to film it with clothes: kzread.info/dash/bejne/q3mp29eaZtLFhrA.html Next time I will wash my 11 shirts.
Can I just say this? This is the worst washer I have ever seen in my life! My great grandmother has one of these and it jumps all over the place when it is in the spin cycle!