what a brave man to give his exact position and data for free

@rajawikiaa

4 жыл бұрын

Who cares where he lives

@kartikagarwal99

4 жыл бұрын

@@rajawikiaa pakistan and taliban does

@Muhammadkhan607

4 жыл бұрын

@@kartikagarwal99 so sad to hear this from you. Kindly focus on the technology how we gonna use it in a better way.

@kartikagarwal99

4 жыл бұрын

@@Muhammadkhan607 Sorry for that

@0xf172

3 жыл бұрын

@@rajawikiaa its not about who care s , it just about how he is honestly :)

Having this much power with so little skills required used to be a dream now you can literally build any hardware with a bit of programming knowledge using these modules.

I think I've seen the Arduino/gps trick before, 2 or 3 years ago. Today somehow I had everything trashed out and you helped me find my way out of the jungle, thanks :-)

10:47 Not gonna expose my location, but here's my exact GPS coordinates

@storyboarddave5860

4 жыл бұрын

Yea Im a secret agent man I must keep hidden! ha

@incognito827

4 жыл бұрын

Layer of obfuscation if one lives in 50 story building.

@waleednazar7003

3 жыл бұрын

yes it takes atleast 6 decimal number after point and then it trace the exact location

Hi Binary Updates. Thank You for the good detailed information on the Ublox NEO-6M gps module. I am going to buy this exact module for a Chromebook that have converted to Android-x86 to use as a dedicated tablet for a drone flying app. I am going to crack open the Chromebook and hopefully be able to figure out a UART location to solder the appropriate pins to along with the 3.3 VDC supply pad,,for module. From doing a lot of reading on these GPS modules there are always manual configurations you have to enter in a couple config files in linux. Have never actually found a how to on Android,which is surprising. Hopefully I can make it work.

Thank you for this (very) clear introduction !

@BINARYUPDATES

3 жыл бұрын

Hi Michel, you're very welcome! Best Wishes

Thanks for shareing your knowledge i'm using the same GPS Module for Sole projects ;-)

BINARY UPDATES makes a useful point in an earlier comment: The TX pin on the UNO connector is connected to the *RX* pin on the chip that communicates with the PC. UBLOX datasheet says TX is an output from its chip, so TX-TX means we're connecting the output of the GPS to the input of the USB converter, which is correct. If you wanted GPS to talk to the Arduino instead of the PC, then you'd need to swap TX/RX. As far as I can tell, the PCB doesn't swap the names, but I remain to be convinced of that..

@anshulmanapure1980

2 жыл бұрын

Can you please elaborate, I'm still new in this so didn't understood much but I think what you are saying might be helpful to my project.

@gettechyt126

2 жыл бұрын

I need gps tracker coding for Arduino or NodeMCU

Question: If the light doesn't turn on on the neo6m, does that mean I shorted it out? I'm still getting values from the SM, they just don't make any sense.

Amazing video.. To get knowledge about GPS module

My daughter tried to connect gps to arduine but could not get any responce. The light ddid not show The connection was correct as per yours but no signe of responce. I tried to help her withe soldering the 4 jumpers and i checked the ohm and the are all 4 pins connected. Is this normal or may be the medual is deffected?

How much did it take for you to get the full line of data? Mine has been on it for about 5 mints and I don't really see much progress!

Hello Sir. Could you make a video on how to use arduino with gps to turn on or off a relay based on speed detected. I'll like to have a gps control relay to turn some lights on in my car when current speed is 10mph. Thank you.

Is the location of the piece determined at the moment? Or experience talking about the itinerary of the trip to and from?

hello is it possible to collect and read the gps data to a cloud using this arduino and neo-6m gps module? how can i do that? Would be grateful for your kind response. Thanks.

Thankyou for this wonderful video. I have learned a lot thanks to you =D

You advise me what type of GBS modules that will be compatible with a Bluetooth module and at the same time an SD card . You can advise me because I'm a little lost thank you

thanks man, this video helped me alot! :D

Thanks dear a lot.I was in the dark world of GPS clock.Ur video find out my path.Again thanks.

@BINARYUPDATES

2 жыл бұрын

Glad it helped

hello, can you answer some questions please 1. this module can work out without an arduino micropocessor? 2. can we send the data to some like mobile or to the web, what do we need to do? 3. does it have a cost to use the satellites, or work with like wifi o is just put the battery and thats all? 4. can we modify the base code and save them inside the gps module? thanks in advice for your time

Great video I have learnt many key points

This video is well explained. But Facepalm after 5 minutes. If you use the 3.3 Volts from the arduino, cause the neo 6m module is only 3.3 volt toleranted, then use a levelshifter for the tx line aswell. The arduino will send the data via tx pin as a 5volt signal bro.

Sir i have done the connections as per ur circuit. but the LED module does not glow on the module. plz help me.i am working on the project related to GPS module. this is the second module. but am not able to understand the problem

Thank you! Helpful video!

stumbles across your post, very interesting ,well done and thanks for sharing.

@BINARYUPDATES

3 жыл бұрын

Hi Mr. Bruce, Glad you enjoyed it

@uditanshusingh656

3 жыл бұрын

@@BINARYUPDATES this method is not working can you plz provide programming one

Thanks man, this information is golden :)

@BINARYUPDATES

4 жыл бұрын

Thanks Mjallux for your comments. Wish you a beautiful day Cheers

Does this module have different version? At 4:35 When you connected ground wire, the led immediate lit up. Mine doesn't. Anyway, I get gps data from serial port. So it's fine right? Also how long does it take for GPGLL to complete? I left it on for 5 minute and still got incomplete data.

@BINARYUPDATES

3 жыл бұрын

Hi Pal, I've used Ublox NEO-6M Module in the video lesson. The ability of GPS module to take GPLL data depends on location where you've placed GPS Module. If its place in open space where GPS module finds satellite quickly then you get GPLL data quickly otherwise it takes time to get exact data. Now how long is bascially depends on place again where you're testing your module

I have some questions for you: What is the GPS module supply voltage on this video ? 3.3v or 5v ?? Do you easily have problems to get satellites fixes ? Since you are indoor.. ?? Where is your clock located in the house ? 1rst floor ? Basement ? Do you use GPS repeater to get sat signals ? I built 2 clock GPS driven using another type of GPS module than the NEO-6M and I'm having a hard time to get satellites signals.. Thanks !

@mucahithamarat2052

Жыл бұрын

Voltage supply of the GPS module is 2.7-3.6V as you can see at it's chip's datasheet www.rlocman.ru/i/File/2011/04/22/1.pdf

Where can I buy neo 6m GPS module, I've searched Aliexpress seems like they are having fake ones...

bro ur so smart and explain clearly

a clear step by step tutorial

3:13 Isn't there a 3.3V LDO regulator connected next to module jumpers. So technically you can connect the module VCC directly to 5v too.

@bilal1708

3 жыл бұрын

yes you can connect Vcc to 5 volts.

@anshulmanapure1980

2 жыл бұрын

@@bilal1708 can you please elaborate what you both are trying to imply

Great video! Thank you for educational explanation

@BINARYUPDATES

Жыл бұрын

Hi Christian, thank you so much! Glad to know you found this GPS NEO6M video useful Wish you a beautiful day!

Nice and informative 👌👌👍

hello every one, I have two questions: 1 how accurate is this gps? 2 Which solution do you propose for some one who needs a precise positioning( maybe with an error equal to 2 cm at most) with respect to some fixed objects marked by a transmetter of signal

@SirMagicaltrevor

2 жыл бұрын

Late reply i know, this unit seems accurate to 2.5m on horizontal position. for something with 2cm accuracy you will need something with a ZED-F9P module. they are accurate to 1cm but come at a high cost.

I just wanna ask if there is voice command/record in it that will where the direction of a specific place? I hope someone can answer me Thanks

perfect description good job man

@BINARYUPDATES

Жыл бұрын

Hi Alireza, Glad you think so!

Nice, easy explanations

Can we track location using Ip adress of the module

Bro got something to ask u , if I connect my arduino uno + arduino gps with using battery ? I'm still can get data in my laptop ?

@hauyik6259

3 жыл бұрын

Pls help me I'm urgent

Thanks a lot sir, very well explained though I am still waiting for the NEO-7M GPS module to arrive

@BINARYUPDATES

3 жыл бұрын

I'm sure you gonna have good time with your NEO GPS Module with Arduino Projects. Have a Fun..Cheers

Thanks bro. Really helpful.

Did this module just worked right out of the box ? or you've to configure it first? Cuz mine one doesn't even power on and nothing shown on serial monitor :(

@anumsheraz

4 жыл бұрын

Turned out, mine one was faulty. Got a new one that worked out of the box.

Thank you very much. Very very good explanation.

@BINARYUPDATES

2 жыл бұрын

Glad you liked it

Hi, It seems this series is not continued. Please give me with links if you published further videos on coding for GPS.

@BINARYUPDATES

2 жыл бұрын

Hi Refayet, I may continue this series later to interface GPS module with Arduino Uno. probably next month as i'm doing very busy these days. I hope you understand.

Is It accurate for indoor navigation ?

hello, I am unable to get GPGLL data alone completely, what to do?

where's part 2 of the video to parse the longitude and latitude?

Very clear elaboration 👌

@BINARYUPDATES

Жыл бұрын

Thank you 🙂

Question when the Module doesn’t light up no more it means it’s fried right?

@anshulmanapure1980

2 жыл бұрын

😂

how to install gps neo 6-m antenna?Is it a plug-in model or is soldering required? Thank you.

@BINARYUPDATES

2 жыл бұрын

Hi Muhammed, GPS antenna comes with its connector which can be easily plug-in to Ublox NEO-6M Module. We don't need to solder it on Module

@muhammedfurkanozdemir4259

2 жыл бұрын

@@BINARYUPDATES Thank you I was able to attach your antenna

On voltage levels, as far as I can tell the module does accept 5V supply as it has a regulator. But UBLOX says the the data isn't 5V tolerant. It's 3.3V CMOS, 3.6V absolute max. The module doesn't add any protection to the TX/RX lines. For breadboarding, I'd stick a 1k resistor in series with each line.

@BINARYUPDATES

4 жыл бұрын

Thanks Mr. Epi for your valuable advice and comment. I appreciate you time to write. Thanks

@boots3372

2 жыл бұрын

I was about to ask about that Tx pin and was worried it'd fry the board. Thank you very much.

Very good presentation

it is taking more than 5 minutes to display stagnant coordinates ? What to do ?

Good work bro, s video ne channel subscribe krny py majbor krdiya, 😇, keep it up.

@BINARYUPDATES

3 жыл бұрын

Thanks and welcome Brother. Good Luck

Sir I tried to connect gps and arduino with different connections still my GPS didn't got any signal(I have ordered a new gps still..) Can u plz help me out? 🙏🙏🙏🙏

@neelmalwatkar6095

4 жыл бұрын

Did try connecting gps out in open?

@ernieferguson6346

3 жыл бұрын

tx goes to rx

tqsm its very helpful

I Connected GPS RX TO ARDUINO TX AND TX GPS TO ARDUINO RX, still works, also, wired on rx GPS 2 resistors 1k and 470 for ground

sir the link of (freenmea.net/decoder ) is not working ?

This would be very useful on my rockets, if I could make my unit smaller...always gotta search for em

@buraqaerospace9945

2 жыл бұрын

Hey I am here for the same reason haha

While the power delivered to the NEO 6M can be 5 volts since it has an onboard voltage regulator, the data lines do not allow for 5 volts and unless a voltage divider or line level shifter are incorporated the voltage of the UNO data lines will destroy most of the NEO 6M's in time.

@BINARYUPDATES

Жыл бұрын

Hi Ronald, Its possible considering lots of Arduino board these days come in market with poor design and power issues. I've used quality Arduino and because of good power and grounding my NEO-6M Ublox GPS Module has tolerated voltage. And it worked in my case without causing any damage to GPS Module. There are so many cheap clones with loosely designed board. And these board needs to be careful with.....This is just my opinion. By the way thanks for sharing. Have a good day

*some one knocks on door* I used your GPS info, I thought I could ask for advice in person

@sparkymarkm322

3 жыл бұрын

We Americans feel the need to f with people for no reason... it's called mental illness

@miharee

3 жыл бұрын

Oh holy Indian tutorial man, I request utmost assistance.

Bro I live in viman nagar 😂 Revell orchid society

very useful, thanks!

@BINARYUPDATES

Жыл бұрын

Glad it was helpful!

hi, have you got this card's eagle library? And if you have got this, can you share with me pls? :)

@busra2435

5 жыл бұрын

or if you know that where can i find it? :)

Hello, i connected my gps module with my esp8266 for the first time it worked but after that I'm not getting the latitude and longitude it's showing 0.000000 for both, even though led is blinking, I'm getting this problem, what's the solution for this??

@BINARYUPDATES

2 жыл бұрын

Hi Darshan, try to place GPS module outdoor in open space. The issue you're facing is because your Module maybe not able to locate satellite....I hope this may help. Good luck!

Hi any chance you can show how to set up a 10mhz frequency standard (10mhz lock) Cheerz

I am using a UART to TTL USB to test my GPS, I keep on getting the raw data your were getting at first. I have waited many minutes but my GPS is not getting any signal. What could be the problem

@BINARYUPDATES

2 жыл бұрын

Hi Tinotenda, Make sure the baud rate of serial communication with default baud rate of your module if you're using USB TTL Converter. Also, change the location. Try to test in outdoor means in open space where it would be easy for GPS Module to get signal. I hope this may help you

How accurate is this module?

Thanks for explic this !!!

@BINARYUPDATES

Жыл бұрын

Hi Lulian, welcome !

Great information and presentation 🙂

@BINARYUPDATES

Жыл бұрын

Hi Mr. Prasad, Glad you enjoyed it!

@prasadadavi6618

Жыл бұрын

@@BINARYUPDATES can we have the data continuously displayed on Google maps when this sensor is mounted on a moving object?

Hi I am having a connections problem with the GPS module and the Arduino, the Arduino always got shutdown when I try to connect the GPS module, specifically when I connect it to the power (5V), I believe it is a problem in the power distribution, plz help me fix the problem 😫🙏🏻

Great video

How much time takes to search satellite? I am not getting that long string.

@BINARYUPDATES

4 жыл бұрын

Usually it takes sometimes around 4-8 Minutes for me. The outdoor satellites is quick to connect and for indoors it takes quite long to connect. i recommend you to sit near window if in case you Ublox NEO-6M GPS Modules takes time to through GPS cordinates. Wish you good day.

red led not blinking after connecting with vcc ,gnd ,rx,tx of gps module to arduino .is gps module not working?

@PasanHerath

5 жыл бұрын

I suppose it works as long as you can see NMEA sentences on the serial monitor.

@meetalisharma8920

5 жыл бұрын

Facing same issue

@abhirajroy2235

5 жыл бұрын

@@meetalisharma8920 hey first time use GPS module in wide open area and wait for 10 minute it will work

@meetalisharma8920

5 жыл бұрын

@@abhirajroy2235 thank you!! It's working now 😄

@abhirajroy2235

5 жыл бұрын

@@meetalisharma8920 👍👍

It help me a lot, thx

@BINARYUPDATES

11 ай бұрын

Hi Cesaramirruizcorces, I'm glad to know this GPS interfacing tutorial was useful. Have a good day!

My GPs is not blinking

Good tutorial

What is the cost of the gps

What happen if we don't unplug the rx and tx connection when uploading? Does it ruin the module?

@BINARYUPDATES

11 ай бұрын

No, It will not ruin your module. The reason to unplug Tx and Rx while uploading code is because Arduino uses those pins. Once the upload is done then Tx, Rx pins will be free to connect to any external devices like GPS NEO-6M Module in this case. I hope this answers your question. Good luck and best wishes!

How can i send the real time gps location to my application

@deeppadmani2993

5 жыл бұрын

you have to send data to any local server using GPRS and your application to local server and you can access the data from any location. and i suggest use GSM 900A module for GPRS.

@coriscotupi

4 жыл бұрын

you can input the NMEA messages from a GPS receiver into your application and parse specific messages (such as $GGA) for time of day.

@armincal9834

3 жыл бұрын

You could even send the data in JSON format using web socket

I am not getting any blinking on the GPS module. Want could be the issue ?

@BINARYUPDATES

2 жыл бұрын

It may be because you GPS Module couldn't track or find satellite. You can try change place preferably in open space you can test if it helps....

Amazing... Diy arduino?

Very Very Nice Tutorial. Is it Accurate or Fluctuating? And I have Heard that It works Not well inside Building or House than in Open Space.

@spencermoody791

4 жыл бұрын

I tried this tutorial on my gps indoors and got the position within a couple feet

I believe it's tx to rx & rx to tx.... transmit goes to recieve

how far can this device work ? ( im wondering working distance) thank you !

@BINARYUPDATES

3 жыл бұрын

So far for outdoor GPS Data tracking this Ublox NEO-M found very reliable for me in my projects

7:08 how can you be receiving things when you didn't even write anything to receive information in the code...?

@BINARYUPDATES

3 жыл бұрын

GPS Chip on NEO-6M Module connects straight to satellite and start giving us latitude and longitude data on serial pins through which we only need to read the data coming from GPS Module. This is how GPS Modules works

After uploading the program in this module, can we track anywhere this module's position in India or the world ?

@BINARYUPDATES

11 ай бұрын

Hi Virendra, it'll work all over the world. As this GPS Module NEO-6M will locate nearby satellite anywhere on the planet to fetch latitude and longitude data. I hope you enjoyed watching this video. Best wishes!

@virendraparihar6982

10 ай бұрын

@@BINARYUPDATES Ok but to get data from this module, we will need to connect this module with any internet source ?

Thank u sir pls make a video with apm 2.6 with same gps

@BINARYUPDATES

4 жыл бұрын

Yes, I'll be coming up soon publishing videos on Drone and relates APM 2.6 with the GPS Module

RX pin to RX pin?

Hi there , i have a question please, i use the same module but sometimes it takes up to an hour , is something wrong with my module?

@BINARYUPDATES

2 жыл бұрын

Hi Sami, Usually it takes time to find satellite but try and test in open space once. If it can help to get data from GPS Module. Otherwise its possible that module may have issue

@samiawadallah6070

2 жыл бұрын

@@BINARYUPDATES thank you for replying , i searched what you said about hot/cold start and it helped me to understand how it works , now i do a cold start before starting my ardusat project then everything goes ok after that in the hot start

When you connect the arduino with the gps without uploading the program and the gps does not turn on does that mean it's not working?

@BINARYUPDATES

2 жыл бұрын

You must upload default Arduino code as i shown in video lesson. And if connections are right then you must see GPS data in serial monitor

Nice man😀😀

thank you

Thank you bro ❤

@BINARYUPDATES

6 ай бұрын

Welcome bro😊

your links are not working,please help .

May i connect it with multi wii

Awesome...

Is it unlimited range and can we also use it for feet detection for module rocket

@BINARYUPDATES

Жыл бұрын

Yes you can use NEO-6M GPS Module for your project!

@aquamarine_editz

Жыл бұрын

Heh heh you were late but thank you 😅actually we are working on a different project our last one was done 👍 it worked.

thank you!!

@BINARYUPDATES

Жыл бұрын

You're welcome!