Excellent video. Thanks for the great info. My 2003 Escalade, 6.0l Vortec with electronic throttle control was idling too high after I cleaned the throttle body and I didn't know how to fix it until after you described "idle re-learn". The two 3-minute idle cycles with a 1-minute cycle in-between worked like a champ.

It worked. I performed the steps multiple times with no success. Started up the truck the next morning after a 30 min drive the night before and it seemed to be ok. Drove it that evening and the problem came back. The next morning it seemed to be fine so I performed the learning procedure with a stopwatch starting and shutting off the truck right on time. (2 times) then drove it problem fixed. Hope this helps.

@cargodchiva1628

2 жыл бұрын

Did it ever come back up after the last time doing it ?

@topmonkey6512

Жыл бұрын

The ECU computer has a self-learning function, but this process is slow and laborious. Throttle learning with software would be appropriate.

@aprilbrown6420

Жыл бұрын

O

@Dbrown65

Жыл бұрын

My truck just idles at 2500 rpm no matter how many times I do this and when I try to drive it it puts the truck in limp mode

@BackYardScience2000

Жыл бұрын

​@@Dbrown65 take your battery off and hit the brakes. That will clear the lump mode out.

Just so u know. I want over 10 other vids about my vehicle that wasnt a gm. An infact not one spoke like u did. So thank u. I appreciated the video

Thank YOU!!! After multiple videos and dozens of threads, this finally did it for my 08 patriot after throttle body replacement !!!

After cleaning the throttle body on my 2008 GMC Sierra 1500 I did this procedure and it worked like a charm. Many thanks. Maybe add a warning to not touch your gas pedal while performing this procedure.

@CardoneIndustries

Жыл бұрын

Hey Jim, thanks for the positive feedback, and for your advice! Be sure to connect with us on Cardone’s other social channels: facebook.com/CardoneIndustries/ www.linkedin.com/company/cardone-industries/ twitter.com/cardoneparts instagram.com/cardoneindustries/

@brandonreed773

Жыл бұрын

Why would they need to add that warning? It should be common sense to not touch the throttle while the THROTTLE body is doing a relearn….

@wphh7272

11 ай бұрын

@@brandonreed773You do realize that we now have “caution hot liquid “ on McDonald’s coffee cups right? Some people are surprisingly ignorant 😂

@kerry6993

5 ай бұрын

😅​@@wphh7272

@Focalpoint100

Ай бұрын

Too funny ​@@wphh7272

Hello everyone. 178,000 miles on my 08 2500HD with LY6 6.0L gas. SES light came on YEARS ago. O'Reilly code reader showed Throttle Position Sensor (TPS) code. Always ran perfectly with no loss of power or fuel mileage. Finally got around to work on it. My Chevy dealership sold me a new TPS (Part # 19259452). $33.18. It does not include the entire TB. Only the plastic part that is clipped on. Came with 6 new clips too. I removed the TPS, cleaned the TB while TPS was off so as not to damage electronics, clipped on new TPS and fired 'er up. Had the common 2000 rpm idle. Performed the idle speed relearn several times as described in this video. Did not solve high idle issue. Thanks to Cory Hayden's comment about his PCV valve not being plugged in, I decided to recheck my work. Yep...forgot to reattach PCV. Cleared codes again by disconnecting battery for a couple mins and performed relearn procedure once more. Lo and behold...it solved all issues!!! Be sure sure to check for any vaccuum leaks (i.e. PCV valve) after reassembly. Hope this helps.

I was told id have to bring my cobalt into the shop at only 75300k to do all sorts of relearns when the car can manage it itself with a little bit of patience thank you for saving me the hassle and money

After one video from another guy saying it cant be done without dealer equipment. And he was a rude person cussing in his video.i found this one and did exactly what it said and it fixed my Sierra I've been messing with for a month thanks guys for the great information.

@christopherfoulk9931

4 жыл бұрын

So did you clean your throttle body on the truck or did you take it off and clean it Or install new throttle body position sensor and clean what year ? And I know what video your talking about lol

@jeanjacque1577

4 жыл бұрын

I saw that asshole he disabled the comments cause he knows he was full of crap

@jeanjacque1577

4 жыл бұрын

@@christopherfoulk9931 I did a new one 2 years ago and the code just popped up on mine 2 days ago . Just cleaned it at 4 a.m. this morning and did the relearn all in less than 30 minutes

@MegaKB33

3 жыл бұрын

@@jeanjacque1577 LOL Me too, Turd disabled the comments kzread.info/dash/bejne/aaN9pKmlesXAdcY.html

@heberlara6079

2 жыл бұрын

Yoo I just came from there saying some stuff like “this video is for adult audiences if you can’t hear the F word go watch some nickelodeon” 😒 so tough 🤦🏻‍♂️

Today I replaced my throttle body on my 07 GMC Acadia, turned it on and I guess I was lucky because the RPM was normal, not high or low, but I still did what you said on the video, the reason I changed it was because I was getting reduced engine power message, I hope this fix the problem. Thanks cardone

@argentino901

4 жыл бұрын

update, reduce engine power message never came back!!

Awesome! Thanks for this! Followed the video exactly and my GMC Acadia is idling perfectly!

I cleaned my throttle body on my 07 Tahoe after my idle was high. I follow these steps after the drive cycle and drove it couple of days after it work perfectly. Thank you for this video. And to the people that say you need a scan tool YOU DONT .

@69arlo

3 жыл бұрын

In high idle was it safe to sift gears

@rcthegod1148

3 жыл бұрын

Just did on mine same thing happening

@rcthegod1148

3 жыл бұрын

Hopefully it goes down soon

@trustinthelord2248

Жыл бұрын

@@rcthegod1148 did it work

@djlivelee3325

Ай бұрын

I hate how they don't respond smh

Excellent video and detailed notes. Great job and thank you !

The Harbor Freight Zurich ZR15 Code Reader for $300 will do Idle Relearn, it's bi-directional, so only this one, not the cheaper models. That will save you from spending the big money on a high end scan tool if you're not in that market. The process in this video didn't work. I tried it many many times, tried suggestions in the comments, tried it with the heater on, disconnecting the battery, clearing codes, while patting my head and rubbing my stomach. You have to do the idle relearn. I replaced the throttle body on a 2008 Silverado and the rpms stayed rock solid at 3000 rpms... Ran the idle relearn with this code reader tool and it was an isntant fix

@CardoneIndustries

4 жыл бұрын

What is the make, model, year and engine size of your vehicle?

Thank you so much. It pays to watch the professionals. All the home mechanics just say "good to go." No, it needs to be done right.

@CardoneIndustries

6 жыл бұрын

Thank you for your feedback.

@dougeckerdt2267

3 жыл бұрын

Kiss ass

Thanks a bunch! It worked like magic on my 07 Uplander!!!!

Thanks for the information. Fixed my 2009 GMC 4.8 liter

Thank you.....Very Informative,,,So Blessed to have Honest mechanics like you....

I had a check engine light couldn't get it to work retried the step 123 numerous times cleared the check engine light worked on the first try u took my worries away thanks for the vid.......

@CardoneIndustries

2 жыл бұрын

Thanks so much for sharing your positive experience! We hope you connect with us on Cardone’s other social Channels: facebook.com/CardoneIndustries/ www.linkedin.com/company/cardone-industries/ twitter.com/cardoneparts instagram.com/cardoneindustries/

@CardoneIndustries

Жыл бұрын

Hello Jack! We are reaching out to invite you to share a positive, helpful, unique, or informative experience you had with Cardone Industries’ Parts, Customer Service or Tech Support Teams. If you are interested in sharing your experience, with the knowledge that it may be shared on our social media outlets, please email me at dmccarthy@cardone.com and let us know. We look forward to hearing your story! Thanks in advance for your input! 😊

Thank you Cardone The procedure worked

@CardoneIndustries

6 жыл бұрын

Glad we could help!

I didn’t replace my throttle body but cleaned it on my 07 avalanche and driving it for a week or 2 eventually brought the idle back to normal

@CardoneIndustries

5 жыл бұрын

Great! Avoid the replacement job when you can👍

It worked let’s see tomorrow if rpm doesn’t stay up when in put on park I ported throttle and manifold

Glad im not the only one driving around with a service tire light on

@Wealthg4ng

2 жыл бұрын

Mannn I have it on too. I've seen videos on KZread about how to reset it but it's complicated lol

Thanks, it seemed to make my chevy sonic more responsive after I had changed the throttle body.

Great explanation, thank you for this!

Sweet! Worked first time. Idles like a champ.

@CardoneIndustries

2 жыл бұрын

Hey Steve, we love to hear when one of our videos is helpful, thanks for letting us know! 👍😊🔧 Be sure to connect with us on Cardone’s other social channels: facebook.com/CardoneIndustries/ www.linkedin.com/company/cardone-industries/ twitter.com/cardoneparts instagram.com/cardoneindustries/

@CardoneIndustries

Жыл бұрын

Hello Steve! We are reaching out to invite you to share a positive, helpful, unique, or informative experience you had with Cardone Industries’ Parts, Customer Service or Tech Support Teams. If you are interested in sharing your experience, with the knowledge that it may be shared on our social media outlets, please email me at dmccarthy@cardone.com and let us know. We look forward to hearing your story! Thanks in advance for your input! 😊

Thanks I work all the time at that type of cars helped me a lot thanks very much

I have an 04 silverado. It was a v6. I put a v8 in a while ago. Just added an nnbs intake manifold in it. But couldn't use the 4 bolt throttle body. My wire was a 4x2 and the nnbs throttle is a 3x2. I bought the adapter and everything I tried this but all it did was started my rpms at 4k and wanted to rise very slowly. With my dashboard saying reduce power. Did the multiple times. But the ecm never cleared it.

Thanks alot my 2008 tbss was giving me a throttle body code and it has helped. Thank you guys .

Just bought a new thottle body thanks for the vid

@CardoneIndustries

2 жыл бұрын

You are very welcome, thanks for the feedback! Please connect with us on Cardone’s other social pages: facebook.com/CardoneIndustries/ www.linkedin.com/company/cardone-industries/ twitter.com/cardoneparts instagram.com/cardoneindustries/

Thank you so so much Cardone Indistries for this information. Very good video.. straight to the point👍

@CardoneIndustries

5 жыл бұрын

Thanks for the feedback, glad the video helped!

I finally found the way to fix that storbon idle problem. Mine was so bad that I actually prematurely wore out my brake pads! I used a combination of several methods, (or trouble shooting techniques). PLEASE PAY ATTENTION and follow my instructions down to the letter / second. First I disconnected the battery, I then removed the throttle body and replaced the air filter. I thoroughly cleaned and reinstalled the throttle body. and then hooked the battery back up. I then performed the following "Reprogramming procedure" : #1 I started it up and let it Idle for exactly 3 min. #2 I shut it off for exactly one min, #3 I started it up and idled it for 3 min. I then took it on the highway, I set the "Cruise control" at 70. I used the "Cruise control accelerate switch" (on the blinker arm) to throttle up past 75, I then disengaged the " Cruse Control" and allowed the vehicle to decelerated down to 60, I then repeated that tree times. I drove it home and shut it off for 15 min. When I restarted it I let it idle till it got to its running temp and it has been perfect ever since. " THANK GOD!. I actually wore out my brakes

@fredycate2329

Жыл бұрын

Hey man im 5 years late to this comment but what does removing the battery do exactly?

@user-kf8ry8qr9h

Жыл бұрын

​@@fredycate2329 it resets all the codes, if you don't disconnect the battery your old codes are in your ECM. You would need to set back to square one by disconnecting your battery so your new throttle body learns the new codes

I cleaned my tahoe 2012 throttle and after starting the car goes to 4k RPM ! , I switched the car off and did the following. First, I disconnect the battery completely. Then, I left the car without battery connection for 24 hours. Then connect the battery gain and start the car and left it running for 3 minutes. The RPM increased to 2K RPM and then decreases. After 3 minutes, I switched the car off for 3 minutes. Then start the car again and left it running for 3 minutes. Then the car off for 3 minutes. Then start it again and drive. It works for me and I hope it works for you as well.

@mauriciomalvaez9123

3 жыл бұрын

No need to plug in a code reader and do a relean?

Cleaned the throttle body on my ‘11 Malibu and the car wouldn’t start. Then it finally started on the third try and was idling at 3k RPM. Got scared for a minute then watched this video. All is good now.

AWESOME! THANK YOU!💜

Great video...good help

THANKS it really help me lots on my 08 silverado 💯

@marcoshdz86

3 жыл бұрын

Did it work for you ? I am having this issue help please !!

@aaronchevy6646

3 жыл бұрын

@@marcoshdz86 yeah it works for me. But all trucks are different my friends truck was doing the same and he had to take the truck for a ride on a highway 75 mph . Thats how he fix his truck

Thanks for helping us solve our own problems with great vids! Didn't realize the relearn is different with every car... could you show me where to find the procedure for a 2007 Chevy aveo hatchback LS?

@mikixP

8 жыл бұрын

how about for a 2006 dodge charger 5.7 ? i cleaned the throttle body and now it wont accelerate , it feels like the car is on limp mode , i step on the gas pedal and the car just doesn't accelerate i even bought a new TB installed it and still have the same problem . please help .

I have a 2009 Envoy. The car was going into limp mode with a code P2135. (rough idle, stalling, ..... 2 times same day). Replaced the throttle body with a new Bosch unit for the 2009 Envoy. The old TB was fairly well carboned. I performed the relearn, it is idling at 700-800 after about 5 seconds after starting. However, when you start to press the accelerator, the car leaches because the engine jumps to 1200 RPM. You just have to barely move the pedal for this to occur. If you are moving and stop, wait 5 seconds, the idle will return to 700-800. If you are in park and you place the car in drive, sometimes the car will increase to 1200 rpm as noted above. I did not have this issue with the old Throttle body. I have driven the car 50 miles with speeds of 50 mph with many stop and go, I am not seeing any improvements. Any ideas? I can't find anything on the internet describing this issue I am experiencing when replacing the throttle body.

@Rokomarn

2 жыл бұрын

I know this is a year late but are you still getting codes?

@OscarHanzely

Жыл бұрын

So what helped, cause I am having exact same issue. It appears to take very long time to re-learn the shifting for me and it still forces the idle to start high and then drop.

@wrenchingwithcrowbar4006

Жыл бұрын

@@OscarHanzely figure anything out?

@bossalienyboss4637

Жыл бұрын

You need the oem part not aftermarket

Worked for me on my 2007 suburban 5.3l. After cleaning throttle body

Trying this on my ‘10 Malibu right now (just cleaned my throttle body…I’ll let ya know how it goes

Thanks for the info great video

Will try this tomorrow. My truck doesn’t idle and during a cruise the truck slowly speeds up. I have no check engine lights but a clean and new tbps

Sir, after cleaning my throttle body and MAF on a 2007 suburban Z71 5.3L, (battery disconnected through entire procedure), I connected everything and started the motor. The idle sat at approximately 2500 rpm. I drove it for 70 miles and it still ran at 2000 rpm. I again disconnected the battery terminal...pressed the brake pedal 3 times...reconnected the battery and started the engine (disconnected batter for about 60 seconds) runs like a champ now. Thank you!

@ThaReal6ix9ine

7 жыл бұрын

This is what is happening to me aswell

I removed and cleaned the throttle body on my 09 silverado 4.3.Idle was high for about 8 days then went back to normal.

@69arlo

3 жыл бұрын

Is it safe to dive in high idle

@antoniotorres3000

3 жыл бұрын

@@69arlo I wouldn't recommend it,but it turned out fine and light turned off.It wasn't too high just a little over normal.Next time I'll just clean without taking it off.

@69arlo

3 жыл бұрын

Thanks ya I had to pull my truck out of the garage but when I did I gave it a little gas it didn't move much so I'm sure I have to have it plugged in

@antoniotorres3000

3 жыл бұрын

@@69arlo I bought a 99 gmc sierra that was parked for over 6 months,but I siphoned the old gas and put fresh.Started up and ran good.

i knew it. thanks alot

I also did it with a nice Autel scan tool. Very quick and easy.

@CardoneIndustries

Жыл бұрын

Thanks for the comment Derek, and for your insight, we love hearing from our customers!! 👋😊🔧👍 Be sure to connect with us on Cardone’s other social channels: facebook.com/CardoneIndustries/ www.linkedin.com/company/cardone-industries/ twitter.com/cardoneparts instagram.com/cardoneindustries/

@matthewwalker1623

Жыл бұрын

My 2001 gmc 6.0 keeps staying at a little over 2000rpm so I'll will probably take it somewhere for them to scan it

Replaced the throttle body on my 17 High Country 6.2L with a Katech had no issues with idling funny or codes

thank you for sharing.

After I clean the throttle body on my 2007 Chevy Tahoe it was idling at 3200 RPMs . couldn't get it to go down . Finally I turned on the AC on high and it pulled the RPMs down enough to be able to drive it

i think , This JJust save my ASS.. cLEaned the throttle body . without studying videos ... and by chance i found your video....and that step of start and idel for 3mins and off for 1 mins.... x3 times.... -=== idel at 500/600 rpm now. ... THANKS man

@elvispressedtalot9899

4 жыл бұрын

2010 silverado cheyenne edition! 3mins idle + 1 min off + 3mins idle + 1 min off + 3mins idle + 1 off + 3mins idle + 1 mins off + 3mins idle.

Thank you for posting this

@CardoneIndustries

2 жыл бұрын

Thanks for the positive feedback Dylan! Be sure to connect with us on Cardone’s other social channels: facebook.com/CardoneIndustries/ www.linkedin.com/company/cardone-industries/ twitter.com/cardoneparts instagram.com/cardoneindustries/

@CardoneIndustries

Жыл бұрын

Hello Dylan! We are reaching out to invite you to share a positive, helpful, unique, or informative experience you had with Cardone Industries’ Parts, Customer Service or Tech Support Teams. If you are interested in sharing your experience, with the knowledge that it may be shared on our social media outlets, please email me at dmccarthy@cardone.com and let us know. We look forward to hearing your story! Thanks in advance for your input! 😊

It works great video

Thank you so much for the helpful information. I have tried this to no avail. However i believe it will work itself out eventually. I just purchase & installed a new throttle body for my 2008 Chevy Express van 3500 series. It still has a very high idle when in park. When i put it in drive it idles normally!

@codybrichard

4 жыл бұрын

JermainesTaxiAndTours any luck?

@joekrim6557

4 жыл бұрын

Check for a vacuum leak

@chrismarek7864

2 жыл бұрын

@@joekrim6557 Vacuum leaks would trigger trouble codes related to them and also the vehicle would exhibit other symptoms like stalling out and lean misfiring.

@topmonkey6512

Жыл бұрын

Buy an AD600S diagnostic instrument, read the engine system fault code to further confirm the cause of the fault, and you can also use AD600S to perform the throttle learning function for your carkzread.info/dash/bejne/g3eb0rh8ddfHorw.html

I changed the throttle body in my 06 Envoy. Drove it for two weeks no problems. Then got the code again P2135/P2176. Then I replaced the gas pedal sensor. 5 weeks later I am still getting the codes every once and a while.

@CardoneIndustries

Жыл бұрын

Thanks for reaching out! This sounds like something our Tech Support Team may be able to shed some light on, you can connect with them by calling 888-280-8324 Mon-Friday 8am-5pm EST to speak with one of our ASE-Certified Technicians. 👌🏼🔧👍🏼⚙

@caballero1152

3 ай бұрын

Hey did you continue having problems?

It worked!! Thank you!!

@kejuanholland8356

4 жыл бұрын

Will this procedure work on a Chevy car also?

@SHOGUNTHEIMPERIAL

4 жыл бұрын

Kejuan Holland This IS a Chevy video sooooo. 🤔

Crank up your heater full blast so thermostat opens up and coolant flows and cools engine down. RPM should lower down

@Woke_R2

5 жыл бұрын

thanks! that did work lol, it wouldnt go down til i did this, said ahhh wtf let me give it a chance.

@tyrellrichardson3078

5 жыл бұрын

Tamara Richardson son of a gun that freaking worked

@daveware9477

3 жыл бұрын

Lol didn’t work until I tried that, thanks

Does it matter whether you drive directly after the procedure or not? Do you HAVE to drive after the procesure? I had ro run back to work so i did the procedure, drove around the corner and cut it off. Wont know if it worked until i leave work

FYI....also be careful not to get carb cleaner into the electronic portion of the throttle body. make sure to tilt the throttle body in such away that the cleaner can't run down the butterfly shaft and into the electronic portion. there's a circuit board inside. and you don't want the cleaner to get on the cir. board.

@rtlf0e630

7 ай бұрын

Will it damage the throttle body if so? My Tahoe now in neutral idles up and down rapidly and n park stays past 1500 rpm’s then drops to normal a few seconds later

thanks man!

I’m About To Try It Now 🤷🏾‍♂️

I did what you mention but my stabilizer alert showing up how do I take it off now?

Thanku God bless you

100% works- disconnect negative battery terminal, pump brake 3 times-- reconnect battery. Rpm will jump to around 1800 then level right off within seconds...

@paxtyngraves17

4 жыл бұрын

ACG Ministries you expect someone to believe that?

@Antgreen79

4 жыл бұрын

Paxtyn Graves lol probably won’t but I found it on a forum last week after I cleaned mine. I did it and it actually worked. Still took about two days of driving to get back to normal but it did work.

@OscarHanzely

Жыл бұрын

ROFL, brakes are not connected at all. What you did is disconnected the battery for long enough to completely reset the ECM unit.

Basically keep turning it off the. On then off the. On for the amount of time needed. Drive it if it doesn’t work and repeat the process if the same issue accrues.

Anyone know how if this procedure is applicable to a 99 Sierra 1500 5.3 LS LM7 when replacing the IAC? It has an IAC and TPS but has the cable driven accelerator linkage. Also. The after market IAC ranges from less than $10 to $134 for the AC Delco OEM. And $50 - $134 for AC Delco. I have a new ACDelco IAC in hand ready to change out the cheap aftermarket.. This whole thing came up when trying to solve the very common and dangerous sticking throttle. Mine started this at 245K but others with these throttles experienced it on many - even relatively new engines. Of course as usual GM did not recall. After decarboning the throttle body I determined that the stick was not in the excelerator cable or butterfly so the only remaining thing was to replace the 2 sensors on the TB. After this the stick was gone but an irregular idle showed up / and it raced at startup. The GMC dealership simply told me I had to replace the throttle body ($500!) which I knew was not the case as the excelerator sticking was gone upon replacing the IAC and TPS. I didnt have the racing idle until AFTER they messed with it CHARGING ME $100! 🤬

Will this work on a 2005 Chevy Malibu

It works, thank you

Thank you..it is

Worked for me on 2007 Silverado 5.3. Bought the Hitachi throttle body to replace factory. Started the truck after. Idled at 3000 rpm. Check engine was still on. Did not have scanner to clear codes. I disconnected the negative on battery then used horn to drain any power left. Check engine was gone. The reset sequence initially did not work. I drove about 60 miles using various backroads to vary speed. When I got back, I tried the reset sequence again and now Idling perfect.

@CardoneIndustries

5 жыл бұрын

Glad you were able to find a solution Jarrod 👍

Hey guys. Thanks for the tips. I was wondering if this will work on a 2004 Cadillac SRX 3.6L also?

@kejuanholland8356

4 жыл бұрын

Did it ever work?

I did a burn out in my Silverado and that fixed it then I went 80mph and she runs good

i just clean it in 2011 silverado n it still accelerated did it twice . what should i do next

Thank you so much

@timmshaw35

5 жыл бұрын

Does this work for a 2006 impala 3.5?

Does this work on 2006 Impala SS5.3Lengine

hey guys thanks for all the tips. will this work on a 2003 Chevrolet Silverado 5.3 ? thank you again.

@tilingastilingas2531

7 жыл бұрын

Cardone Industries it is electronic I'm having the reduced engine power code

what's the relearn procedure for a 06 grand prix 3.8L

Hello, very helpful and did help, but after a smooth idle i would rev it up then it will kick back up to 1500 rpm instead of 850-1000 what do you recommend?

@OscarHanzely

Жыл бұрын

Yeah, I am very careful to even wait when shifting to park so the idle gets down with gear engaged. I think it needs several drive cycles for days to re-learn everything. Did it settle for you shortly after, or what was the solution ?

@AaronFernandes__

Жыл бұрын

@@OscarHanzely I forgot about this comment lol, if I remember correctly what I did was hook positive and negative cables together overnight with battery out of vehicle. Then next day I hooked together and it took awhile but it did eventually work again just fine.

Just received a Cardone remanufactured throttle body for my gm. You can see it was sandblasted, which isn't a problem. However when shaking it and moving the throttle blade, there was clearly sand coming out, and you could feel and hear sand grinding in the shaft. Maybe clean these out better before shipping?

@CardoneIndustries

2 жыл бұрын

Thanks for the comment Thomas, sorry you had this issue. This sounds like something our Customer Service could help you with, please call them at 800-777-4780 Mon-Fri 8am-5pm EST. If you have a question for our Tech Support Team, please call 888-280-8324 Mon-Friday 8am-5pm EST to speak with one of our ASE-Certified Technicians.

I have tried the relearn procedure without hooking up a scan tool. I had no luck. So I had to use my scan tool and it was reset in less then a minute. I have made good side money getting called by other shops to show them or do the relearn procedure for them

@dwsherm1

5 жыл бұрын

So did you just erase the code and do this key on/off relearn procedure?

@johnrusselfromthatmovie4720

4 жыл бұрын

What scan tool ? I would like to know which brand and model ? i am sick of having to give money to chevy for repairs that are fake and could be done with a paper weight dropped on a few buttons. please let me know

@feeneysmechanical6215

4 жыл бұрын

@@johnrusselfromthatmovie4720 I am using a snapon solus edge. But a snapon solus pro or ultra will do the reset

Would this work on my 2006 Chevy HHR that's been getting a P2176?

thank you

Excellent !

That was great video

@CardoneIndustries

2 жыл бұрын

Thanks for the positive feedback Patrick! We hope you connect with us on Cardone’s other social channels: facebook.com/CardoneIndustries/ www.linkedin.com/company/cardone-industries/ twitter.com/cardoneparts instagram.com/cardoneindustries/

@CardoneIndustries

Жыл бұрын

Hello Patrick! We are reaching out to invite you to share a positive, helpful, unique, or informative experience you had with Cardone Industries’ Parts, Customer Service or Tech Support Teams. If you are interested in sharing your experience, with the knowledge that it may be shared on our social media outlets, please email me at dmccarthy@cardone.com and let us know. We look forward to hearing your story! Thanks in advance for your input! 😊

Same problem here. 2007 GMC Yukon Replaced throttle body, sensor, pedal with sensor and connector cables. I still have the check engine light come on with codes P2135 and P2101. What else is left to fix??????

2003 silverado 5.3L. check engine light on showing o2sensor system too lean and reduced engine power. after replacing the electronic throttle body i deleted the codes and a few days later check engine light came on showing code p0332 knock sensor any tips on this one . please let me know thanks

Will this work on a Buick Rendezvous CXL 3.6 L?

I guess that is the problem with my 07 Cadillac CTS. Will it work on my car? It’s the reason it has been sitting for a year. No power when I start it, idle is shaky and loud. Please help.

Thanks! 🙏

Hy guys thanks for all th cool tips... very helpful. I was wondering though, is there a relearn procedure for a 93 Chevy Blazer K1500 5.7 Automatic? Im having troubles after swapping my ECU.

@rickrichie3936

7 жыл бұрын

+Cardone Industries Thank you, i appreciate it. I guess i have an issue with wiring then.

@rickrichie3936

7 жыл бұрын

+Cardone Industries Ok cool, Much appreciated! I will if in need, thanks!

did what you said, still have an iratic idle after cleaning the throttle body of carbon build up, even took it for a drive...it seemed fine for a day then , the idle became erratic again and a check engine light came on

@user-lg6qg2cf6x

5 жыл бұрын

Which code did you pull?

@cerealrakist7360

Жыл бұрын

Same issue

Thanks mate, I didn't know ..

@CardoneIndustries

Жыл бұрын

Thanks for commenting Jake, be sure to connect with Cardone's other social channels: facebook.com/CardoneIndustries/ www.linkedin.com/company/cardone-industries/ twitter.com/cardoneparts instagram.com/cardoneindustries/

would this work for a 2010 traverse lt 3.6? I'm getting the dreaded p0221 code. just got the throttle body today and was going to replace tomorrow

you need a scan tool that has the idle relearn/reset feature. I've never heard of this method working

@jeanjacque1577

4 жыл бұрын

No you dont

@AltruisticWarrior

2 жыл бұрын

Worked just fine for me.

What if your car doesn't idle for three minutes? can you rev it to keep the engine running.

Will this work on 2012 Silverado 1500

I have a 2008 Acadia with the oil settling in the intake from the throttle body and get stabilize link traction control and engine powering off. I thought of changing the throttle body. Any suggestions please?

It's the same thing for a Chevy cobalt 2008 ???

I am replacing a throttle body in 2008 cts automatic. Can i do the relearn myself on this vehicle or do I need to take it to the dealership. I would like to know before i do the work my self being that I bought the part and gasket. please help thanks alot

Is it applicable in Chevrolet Spark for this procedure? Can give me advice on how to relearn my Chevrolet Spark? Thanks

will this work on a GM car? such as a chevy cobalt?