Will the vehicle function properly without doing the relearn process??

@HitachiAstemoAftermarket

4 жыл бұрын

Without the re-learn process, your Nissan will not perform properly. This training process is required by the manufacturer.

@steve210sa

4 жыл бұрын

@@HitachiAstemoAftermarket ok thank you. We replaced the throttle body and did the re-learn process with no problems.

@theflaxxseed8478

3 жыл бұрын

I've removed the etb cleaned it and reinstalled it without doing the relearn process and idle was over 2000 rpms 🤣. After applying the relearn method it ran fine.

@thenewbrc1382

2 жыл бұрын

I'm most likely going to end up doing the relearn procedure on my 02 Xterra, but after cleaning the throttle body and reconnecting everything, it seems to be idle fine. Won't it relearn on its own as you drive it?

@nikaclark3286

2 жыл бұрын

Will this work on a 2014 Nissan Versa ?

The engineer that came up with this list must have really hated humanity.

I removed and cleaned out the electronic throttle on my Versa 2011 recently. After which i reassembled it back on the engine no problem. But apon engine start, the idle went berserk and was all over the place. I tried everything literally, i had to remove and assemble it a couple of time and clear codes thinking maybe i missed something but nothing worked. I was given up untill i came across your video, and EUREKA!. It smoothened out like a charm. Thank you so much for you very helpful procedural video..i know it saved me alot😅.

You are the man! I've been trying to perform this relearn from written instructions for 2 hours. It wouldn't take until i followed your instructions. The timers and side by side view of the pedal and cluster really helped! Thank you so much.

@HitachiAstemoAftermarket

Жыл бұрын

Thanks 😀 We tried to follow the paper instructions by ourself and ended in the same situation as you. Videos help today a lot!

Worked like a charm! Thanks guys

@HitachiAstemoAftermarket

3 жыл бұрын

Hello Steve, you're welcome! Stay safe on the road.

This procedure saved my 2011 Nissan rogue. Thank you

@HitachiAstemoAftermarket

2 жыл бұрын

Awsome 👍

Thank you. This helped me today!

@HitachiAstemoAftermarket

4 жыл бұрын

We're glad we could help you.

Thank you so much for sharing this very precious information. It did actualy fixed my “high idle” issue on my Micra 1.6 .

@HitachiAstemoAftermarket

2 жыл бұрын

Hello Dear customer, you're welcome 👍

@cadevolker5329

Жыл бұрын

Did the engine light flash on your micra ?

I tried this today after thoroughly cleaning my MAF and Throttle Body on my 2011 Nissan Altima and my car runs sooo much better than before. Thank you so much for this video!!

@HitachiAstemoAftermarket

2 жыл бұрын

Thast awsome :) We are glad, that the video helped you.

Thank you . I just clean the throttle body while still attached. And use this technique. And the check engine light off now .

Thank you that was actually really helpful helped me alot.

@HitachiAstemoAftermarket

3 жыл бұрын

Hello Petar, thank you for the comment!

Thank you very much worked for my 2010 k12 micra

My TPS went bad on my Infiniti G 37 I’m getting a whole new throttle body with sensor . After I replace it I’m gonna follow your instructions 😊

Work! I’m a female and had to do it myself and it actually worked lol thank you so much for the quick and easy instructions

@HitachiAstemoAftermarket

2 жыл бұрын

Awsome! 👍

@juliochavarria9192

Жыл бұрын

Awesome sweetie 😉😉🌹🌹

Worked great after cleaning the throttle body on my 2014 Altima. My idle is back down to 750RPM.

Thank you for this video!

@HitachiAstemoAftermarket

3 жыл бұрын

Glad it was helpful!😀

Thanks for post this video❤️

ty man u r the best worked for my nissan qashqai

So far so good. Didn't get a new throttle body, just cleaned it. But it was very helpful for sure. Thanks for the comprehensive video.

@HitachiAstemoAftermarket

3 жыл бұрын

Hello Juan, we are glad, that we could help you! Could you relearn the ETB at the first attempt?

@juanmanuelpenaloza9264

3 жыл бұрын

@@HitachiAstemoAftermarket yes, thank you.

@HitachiAstemoAftermarket

3 жыл бұрын

@Juan Manuel Penaloza So thats awsome 👍 We tried it at least 5 times 😂

@juanmanuelpenaloza9264

3 жыл бұрын

@@HitachiAstemoAftermarket well if it helps someone get it right the first time then it's worth it.

@henrytom5824

3 жыл бұрын

How is this done 2013 Nissan Altima push start ? Would like to clean the throttle body without removing it just opening flaps. I’ve done this on my Hyundai but never needed to do relearn ?

This will definitely help I have to replace my throttle body on my 2006 nissan sentra 1.8s because the motor circuit is running to high

Great video, thank you

@HitachiAstemoAftermarket

Жыл бұрын

Glad you liked it!

Awesome video! Really the only one that was easy to follow and got my nissan working. Thank you

@HitachiAstemoAftermarket

3 жыл бұрын

Thanks! Glad that this helped you!

It worked , thanks

Thanks a lot brother.....

the best !

@HitachiAstemoAftermarket

2 жыл бұрын

Thank you! 🙂🙂🙂

Been having a problem with my 2018 Rouge Code P2101 comes up. Took it to the dealer and after $200 they couldn't find anything wrong. Check engine light would come on every once in a while (code P2101) I followed the re-learn and haven't had a problem since. Thank you

@diegocuevas7587

13 күн бұрын

There's a TSB for those codes relating to the throttle body. Look them up.

Installed Hitachi ETB0004 on my 07 Altima 2.5S. After performing this relearn, I kept getting P0507 (High idle rpm). The engine rpm was around 925-1,100. I found out that you have DRIVE for 15 mins to bring the car up to operating temp. (From altima forum) Then I performed the relearn procedure again and it worked. My idle rpm is now 625.

@HitachiAstemoAftermarket

3 жыл бұрын

Why did you replaced the ETB in first place?

@flavaj78

3 жыл бұрын

@@HitachiAstemoAftermarket I was getting some mis-fire codes during cold startup. I changed the spark plugs and the coolant temp sensor... I thought throttle position sensor could be replaced, but since it was integrated, i just replaced the entire unit. My car has 190K miles on the original Hitachi throttle body... so i figured it might be the problem.

@HitachiAstemoAftermarket

3 жыл бұрын

@@flavaj78 Yes, it is really important, to bring the car to operating temperature.So sounds like you had to check few thing in the first place. How about the ignition coils, are they OK? Some time when misfiring occur during start, the coils can be bad, too.

@flavaj78

3 жыл бұрын

@@HitachiAstemoAftermarket Thank you! Yes! I actually just ordered the Hitachi ignition coils IGC0002. I am planning to change all 4x coils out this weekend. Now my new MIL code is P0303. I've also ordered Cam Shaft Position and Crankshaft Position sensor as well.

@HitachiAstemoAftermarket

3 жыл бұрын

@@flavaj78 Hello, please replace the spark plugs, too. They are not so expensive and you will benefit in the end, because you already have to remove the coils. First replace the coils and spark plugs - if it works, you can keep the old sensors. 👍

thanks for the method. the last step, i hold it for 20 seconds, then i let it run in idle for more than 20 seconds before short trip home. seems like drive better, i wasnt sure, will find out 2moro. *history i took off the whole throttle body for cleaning, it did not drive well then, poor acceleration and poor fuel mileage. 2014 nissan sentra/sylphy 1.8

Useful video guys. Btw, what software did you use to check parameters VIA CAN?

@HitachiAstemoAftermarket

3 жыл бұрын

Thanks Mr.T! Actually we just simulated a system, to show you everything in a short time. You can use a normal OBDII diagnostic software, which is capable to read errors and parameters.

@_-_ttt_-_

3 жыл бұрын

@@HitachiAstemoAftermarket thanks 🤓

@HitachiAstemoAftermarket

3 жыл бұрын

@@_-_ttt_-_ Check our other videos, too.

Is there a way to do this when you can’t bring the temp up to operating temp? Dealer said idle relearn requires coding. I unplugged the throttle to clean it then plugged it back in. I also changed the spark plugs. The rpms buck and surge at idle.

@HitachiAstemoAftermarket

2 жыл бұрын

Hello Melissa, not really. The engine must be at operating temp. to do it properly with this procedure.

Good day. May i ask does it work with nissan navara np300 series? I have this severe engine vibration. Planning to reset the ecu. Thanks for any help.

@HitachiAstemoAftermarket

3 жыл бұрын

Hello Zy, please send the VIN or chassis number to techsupport@hueco.com and we check that for you!

This REALLY HELPED I thought I broke it😂

@HitachiAstemoAftermarket

3 жыл бұрын

The ETB should only be considered defective only after the 20th re-learn attempt.

This procedure Does it include all kinds of Nissan cars? Does it include the rogue sport (qashqay) 2018 car?

@HitachiAstemoAftermarket

4 жыл бұрын

Dear Ary, we´ve done the relearn process on a fairly new Nissan and it worked. Please check whether a instruction manual is enclosed with our product. If so, you can use this video.

What about a 2017 Nissan Titan with the Push to Start button?

Excellent thank you. If check engine light doesn't blinking??

@HitachiAstemoAftermarket

4 жыл бұрын

Hi Khaled, if it´s not blinkig please check if the previous mentioned requirements are fulfilled andd repeat the procedure.

Is this applicable for renault fluence 2011 made in korea with the same throttle valve and engine nissan L304?

@HitachiAstemoAftermarket

3 жыл бұрын

As far as we know, it's only for Nissan

This works with Nissan Rogue and Renault koleos 2018??? Thanks from Costa Rica 🇨🇷👍🏼

@HitachiAstemoAftermarket

3 жыл бұрын

Hello Oscar, this should work with Nissan, about the Renault, we are not sure.

How can you bring the vehicle up to operating temperature if you can't get the vehicle started I put a new throttle body on it because it didn't want to start it would just start every once in awhile it acted like it would start but it wouldn't start

I cleaned throttle body of Almera N17, did the relearn process. The idle speed is 750 without air cond on. It looks good. However after air cond on,, its idle speed increase to 1000rpm. Higher than originally 750rpm with air cond. How can I correct idling to 750rpm with air cond. ? Higher fuel consumption if idling at 1000rpm with air cond on.

@HitachiAstemoAftermarket

Жыл бұрын

Usually the AC needs some power from the engine and will raise the RPMs when switched on slightly. Please check you AC compressor if it was maintained correctly.

did procedure everything felt fine but the check engine is still on? is it supposed to turn off after the relearn or is it supposed to turn off after driving?

@HitachiAstemoAftermarket

3 жыл бұрын

Hello, one question why did you replaced the Pump? What problems did the car had? What error codes are in the ecu?

@leonidasx3007

3 жыл бұрын

@@HitachiAstemoAftermarket hello I was told maybe throttle sensor. But after viewing this video. I’m thinking it’s this part. (Can’t remember name) my car has a little trouble on shifting out of first gear. (ITS AN AUTOMATIC) but eventually does. Sometimes it changes ok depending on acceleration. If fast or slow... please help me because I cannot find the proper sensor to my Nissan 06 Sentra 1.8

I understand this is for a ETB replacement. But would this relearn procedure be recommended when installing a new MAF sensor?

@HitachiAstemoAftermarket

Жыл бұрын

Hello Raph, not really.

so do i need a computer to do this? or is this something i can do at home with out taking it to a shop?

@HitachiAstemoAftermarket

Жыл бұрын

THis video helps you to do it at home. But if you have errors in the ECU it wont work.

I just cleaned my ETB and I definitely need the "relearn" as my idle bounces from 1500 to 2500 rpm while in park. While in drive, I actually get up to 40mph, from a dead stop, just by releasing the brake. How do I modify these instructions to work with my push button ignition? One press turns my accessories on, 2 pressed turns my ignition on. So..... press twice everywhere the video says to turn the ignition on and once again to shut it off in the places we were told to turn it off? Thanks

@HitachiAstemoAftermarket

2 жыл бұрын

Hello Dear Customer, please use the button like the key. You dont need to start the engine with the button, but you can switch ignition on. At kzread.info/dash/bejne/momgqdqqqc_Wc9Y.html - you need to switch the igniton with button on. Here at kzread.info/dash/bejne/momgqdqqqc_Wc9Y.html switch ignition on with the button and continue to follow the instructions. Be aware, that you dont need to start the engine just switch the ignition on.

@Ten_Mil_Will

2 жыл бұрын

@@HitachiAstemoAftermarket awesome! Thank you. I'll get this done this morning, just cleaned it last night and it seemed to fix my rough idle and hesitation problem. Again, THANK YOU!!!!

Excelente video !! Tengo un problema con mi Nissan Sentra 2013 STD , limpie el cuerpo de aceleración sin desconectar los conectores tuve mucho cuidado de no mover el actuador , no tenía codigos antes de limpiar ni después , pero ahora al momento que lo prendo suben la revoluciónes y luego ya se normaliza funciona normal , el problema solo está al prenderlo ¿ Alguna idea que puede ser ? Lo limpie con producto especial

@HitachiAstemoAftermarket

3 жыл бұрын

Hola Luis, ¡nos alegramos de que te haya gustado este vídeo! También tenemos este video en español: kzread.info/dash/bejne/aH2duc-beajLZrw.html Después de limpiar la ETB, tienes que hacer el procedimiento de reaprendizaje.

Will this work for a 2018 Nissan Sentra?

Would it work on a 2012 Pathfinder?? Thank you!!

@HitachiAstemoAftermarket

3 жыл бұрын

Hello, has the Pathfinder a gasolne engine? If a Hitachi ETB is installed it should work.

Hi , 2003 350z rpm getting stuck at 1500 while driving . This started happening after cleaning thr throttle body, also idle rpm resting at 900rpm

Hallo what is good aftermarket Nissan quest electric throttle brand you recommend

@HitachiAstemoAftermarket

3 жыл бұрын

Dear customer, we are the OE manufacturer for ETBs, so you can choose our brand - Hitachi or HÜCO

Should I do this procedure after installing a new or old Throttle Body? I did this procedure 4x in the past two days and the car still idles high. I'm guessing it's time to replace my old throttle body.

@HitachiAstemoAftermarket

Жыл бұрын

Please check if there is a leak somwhere. You should relearn the ETB if you do some maintanance on the ETB or repleaced the ETB with a new one.

I need to do this to my 2003 Nissan Sentra ser spec v but the check engine light isn’t on. My gas pedal will stop working randomly and my idle goes up and down.

@HitachiAstemoAftermarket

3 жыл бұрын

Hello Michael, why you need to relearn the ETB? What repairs were made? Are there any errors in the ECU?

Hi. Does hitachi sell their mass air flow sensor as well as the throttle in south africa.

@HitachiAstemoAftermarket

3 жыл бұрын

Hello Collin, could you please tell us where you live? It would even better if you send your request to techsupport@hueco.com and discrive where you come from and what parts do you need.

@collinram5790

3 жыл бұрын

@@HitachiAstemoAftermarket I am from South Africa.

If not succes, should i repeat from disconnect 30s for battery again?

@HitachiAstemoAftermarket

3 жыл бұрын

Hello Dear viewer, it's than not really necessary. Important is, that the engine is at operating temperature.

I have a 2000 nissan pathfinder will this work on my truck...ty

@HitachiAstemoAftermarket

2 жыл бұрын

Hello Richard, if you have an ETB, than this should work.

Hello good day,i have a nissan xtrail 2005 model and the problem is the rpm is 1200 and check engine indicators and then no acceleration,can you help me with this problem,thank you in advance

@HitachiAstemoAftermarket

2 жыл бұрын

Hello Jordan, do you have a OBD2 reader?

im on my 7th hitachi throttle body in my nissan quest. 6 months to a year i am replacing it, i keep losing throttle response. changed pedal. ecu and still

Will this also apply to montero sports gen 3?

@HitachiAstemoAftermarket

3 жыл бұрын

Hi Karl, this relearn video is only for Nissan.

Does the procedure work on Nissan Rogue 2013? Thank you

@HitachiAstemoAftermarket

Жыл бұрын

Hello Cris, this should also work on your car.

Will this work on 2014 Altima with the push button start?

@HitachiAstemoAftermarket

2 жыл бұрын

Sure, use the button like a key we used in the video.

when you say to repeat the entire procedure do you mean right from the get go... (the 2 second / 10 second proc) or the second procedure ( 3 sec / pedal pressed 5x within 5 seconds)?? thanks

@HitachiAstemoAftermarket

3 жыл бұрын

Hello Andy, please repeat the whole procedure to make sure everything works right.

Will this work for Note 2010 1.4 petrol+lpg? Thanks in advance!

@HitachiAstemoAftermarket

Жыл бұрын

Hello, if your LPG systems is installed correct, than yes.

Does this work on the tb48 Nissan patrol

@HitachiAstemoAftermarket

3 жыл бұрын

This procedure should work any Nissan cars with one Hitachi ETB

Will this work on a 2015 Nissan Sentra SV 1.8L? Thanks!

@HitachiAstemoAftermarket

3 жыл бұрын

Hello Joseph, if you have a Hitachi ETB, this should work

I have Automato car Nissan Tiida ratio 4x4 the problem is engine light that happened after cleaning the THROTTLE BODY.. and theRPM point is moving up and down and when i started the car it sounds up and down like accelerate by itself 🎉 so what is the solution?🎉

I have Nissan Quest 3.5 S 2007. Replaced Throttle Body and did relearn multiple times. Idle is around 900 rpm so little on higher side. Do we need to disconnect battery for relearn all the times ? I don't have any error code.

@HitachiAstemoAftermarket

3 жыл бұрын

Hello Mr. Gupta, please send the VIN to techsupport@hueco.com and we check if you can apply this procedure.

@vainoampweya4970

Ай бұрын

Hi,?.. help me I have Nissan Tiida ratio 4x4 ..the problem is the dashboard engine light that occurred after I cleaned the Throttle body butterfly valve ..then the RPM point is moving up and down with engine light ..and when I start the Car it is sound up and down like accelerate by itself ..so I give me the ideas resolution. 🎉

If I have a check engine light on can I still do it

@HitachiAstemoAftermarket

3 жыл бұрын

Hello Bob, there shouldn't be any errors in the ECU. Please cehck first, what the error is.

My 2005 Nissan Sentra 1.8 S with the 1.8 liter (4 cylinder) just started having the "dying while driving" trouble. Trust me, it is not fun or funny when it happens. EXTREMELY DANGEROUS !!! Just driving along and it's like someone turns off the ignition key. No power steering and no power brakes !!!! If I wait 10 minutes, the car starts back up (until it doesn't) like nothing ever happened, until it happens again. I just drove a 265 mile trip (all highway) that normally takes 4 1/2 hours now took 7 1/2 hours !!! Three (total) HOURS on the side of a 4 lane interstate highway !!! It shut off about 20 times !!!!! Never had an issue if I just drive it short distances around town doing errands, but not long highway driving. The car runs perfect (except this problem) and burns zero oil even with 330,000 miles (original engine) and gets 33 mpg. I hate to get rid of it but my wife will not drive it, and I won't allow her to any longer. New cars are no better than the old ones just more expensive. Any help out there ?????

@HitachiAstemoAftermarket

2 жыл бұрын

Hello Tim, no car is worth risking your safety for. But we also understand that you are attached to your car, so we try to help you from a distance. Could you please tell us: #What maintenance prescribed by the manufacturer has been performed recently? #Has the throttle been cleaned? #What error codes are stored? #Is the fuel pump and ignition system working properly? After the car stops, check if the throttle is activated and if it reacts.

@saramessmore

2 жыл бұрын

crank sensor

We replaced the thermostat on 2010 xterra n it not performing like it was b4. Everytime we press the gas pedal it dies down. What ya think is the problem? We had no problems b4 our heater core assembly broke replace that too n replace thermostat now this. Please help. Thank u

@HitachiAstemoAftermarket

3 жыл бұрын

We try to help you. What have you removed or disconnected during the installation?

@jl-heatfan4life717

3 жыл бұрын

Sum hoses and throttle body airfilter to get to the thermostat. The thermostat sits bottom left of engine

@HitachiAstemoAftermarket

3 жыл бұрын

@@jl-heatfan4life717 Please check that the hoses are correctly connected and that there are no leaks. Also the MAF should be connected, too. Please check with an OBD device if there are errors in the system.

@jl-heatfan4life717

3 жыл бұрын

So do i do re-learn procedure everytime we disconnect the ETB?

@HitachiAstemoAftermarket

3 жыл бұрын

@@jl-heatfan4life717 If you change anything on your vehicle that could affect the ETB, we would advise you to relearn it. Check that the ETB is connected correctly, check all hoses and fuses and check that the fuel supply is correct.

Doesnt work on my 2009 nissan bluebird sylphy. Smh i cleaned the carburator n reinstalled it and now i have a high idle. i did this method over 10 times yesterday with no luck

@HitachiAstemoAftermarket

2 жыл бұрын

This is only for ETBs not cars with carburators.

Works with mistubishi montero sport also?

@HitachiAstemoAftermarket

3 жыл бұрын

Hello Karl, sorry this is only for Nissan.

🦁🐯

I allready did the relearn process a couple times exactly the way it supposed to be, but still it didn't fix the problem....RPM'S go up to 2,000 and every 5 seconds it drops to 950 RPM and back to 2000 rpms again(2005 Nissan Pathfinder SE 4.0) 1.) new Vias control solenoid valve 2.) new O 2 sensor 3.) new vac hoses and no vacuum leaks detected.... Any suggestions????😔🙏

@HitachiAstemoAftermarket

2 жыл бұрын

Hello, could you please tell us how the problems started at first? Is the MAF ok? Are the O2 sensors OEM quality? Are there any errors in the ECU?

@abrazosnobalazosxd1827

2 жыл бұрын

@@HitachiAstemoAftermarket it started after changing the valve cover gaskets since they had a small leak, and since it was allready getting worked on I decided all vacuum hoses to get replace with new ones...and since than I just started to idle too high I checked for vacuum leaks with a brake cleaner and it didn't show no symptoms... MAF is okay and I also cleaned it with MAF cleaner 02 got replaced (aftermarket/O' Reilly autoparts) and IAC/VIAS sensor also got replaced. so I decided to get another throttle body and RPM's did go down to 1,500/1,400 And its steady now, did another relearn procedure with no success code p0507 keeps showing up

@HitachiAstemoAftermarket

2 жыл бұрын

@@abrazosnobalazosxd1827 Hello, please check the MAF with an osxilloscope - usually MAFs can't be cleaned without damaging something. Especially the hotfilm one. Please also verifiy if the aftermarket O2 sensor is working properly. Also please check they gaskets and the vacuum system again. Maybe there is something. If there is an error code, you can't relearn the ETB properly.

How come it said hold it down till it stops flashing but then is says soon as it’s flashing for 3 seconds let go of the gas pedal? So confused

@HitachiAstemoAftermarket

3 жыл бұрын

Dear David, if you have problems, please use our manual in the package.

Does this method work on a 2007 Nissan Qashqai petrol? RPM to 2000

@HitachiAstemoAftermarket

2 жыл бұрын

Hello Esam, please check if there are no error in the ECU, this method should work for you.

2014 nissan maxima I chance my mass air flow sensor 4 days ago but I still have the soon engine service light on what I have to do next ?please help me

@HitachiAstemoAftermarket

2 жыл бұрын

What for problems did you have with your car before?

@chuguito26

2 жыл бұрын

I had the engine service soon light on I went to auto zone to check what code and came out the mass air flow sensor code

@HitachiAstemoAftermarket

2 жыл бұрын

@@chuguito26 Please check if the MAF is working probperly (one of our videos shows how to do it properly) and if defective replace it.

Does it apply for push button? 2009 murano

@HitachiAstemoAftermarket

2 жыл бұрын

Sure 😀

does this process work with the Nissan Versa n17?

@HitachiAstemoAftermarket

Жыл бұрын

It works on every Nissan with an ETB

and if i do this and check engine light blinking repeatedly?

@HitachiAstemoAftermarket

4 жыл бұрын

Hello Jesse, sorry for the late reply- if it´s not blinkig please check if the previous mentioned requirements are fulfilled andd repeat the procedure.

@josesantana9044

3 жыл бұрын

Did you figure this out mine is doing the same thing

Sir can it be done with kwid throttle body

@HitachiAstemoAftermarket

4 жыл бұрын

When you purchase a new Hitachi Throttle body, please make sure that you read the installation instructions. The instructions will tell how to relearn the ETB

Does this need to happen on a 2013 with push start?

@HitachiAstemoAftermarket

Жыл бұрын

Sure, it works also on a push start.

How is the procedure like for Nissan pushstart? Thanks

@HitachiAstemoAftermarket

4 жыл бұрын

Hello Edvan, could you please paraphrase your request? We still dont understand what you want to do. Thank you.

@edvanteo4834

4 жыл бұрын

@@HitachiAstemoAftermarket my car comes with Intelligent Smart key FOB which is the Push Start button.

@HitachiAstemoAftermarket

4 жыл бұрын

@@edvanteo4834 Do you still have a start button on your dashboard? If yes, use the button like the key. Also please make sure, that your ETB can be relearned with this process.

I tried cleaning throttle body 2010 altima 2.5s notice that the butter fly won't open to clean it and had to force it open the cleaned it turn the car on the RPMs wire fine but didn't notice any difference with the car. It still shakes and runs ruff.

@LuisRamos-it3mb

2 жыл бұрын

Should I relean the throttle body ?

@HitachiAstemoAftermarket

2 жыл бұрын

@@LuisRamos-it3mb Hello Alyssa, sure this should help.

Will this work with a 2018 Nissan Altima SV?

@HitachiAstemoAftermarket

3 жыл бұрын

Dear customer, could you please give us the OE number of the etb?

No work on my Nissan sylphy G11. The check engine light won’t blinking. But I’m not change new throttle body, I just cleaned the throttle body n manifold. Now the timing a lit bit high than previous. Dunno how to reset back to normal. I asked the foreman, the told me sometime need drive few days n let it learn, after will bcome to normal, not sure true or not

@HitachiAstemoAftermarket

3 жыл бұрын

Hello Dear viewer, do you have an ETB or just thorttle body with wires?

@vls1437

3 жыл бұрын

@@HitachiAstemoAftermarket YES, MINE IS ELECTRONIC THROTTLE BODY

@vls1437

3 жыл бұрын

@@HitachiAstemoAftermarket I FOLLOW THE STEP AND PRESS THE PEDAL, THE CHECK ENGINE LIGHT WONT BLINKING

@vls1437

3 жыл бұрын

@@HitachiAstemoAftermarket DONE, TIMING NEED VERY accurate. before that i just cleaned my throttle body and manifold, so the rpm a bit higher. but your way just only can reset ECU, i combined with other step, now the RPM timing back to normal. thanks for your shared also, thank you :)

@HitachiAstemoAftermarket

3 жыл бұрын

@@vls1437 Yes indeed, timing is super important

does this work on Infiniti's? I have a 2007 G35s Sedan and have a high idle with no leaks, did clean my throttle body and tried the idle relearn but was not successful, I still have a high idle at 1,200 rpm.

@HitachiAstemoAftermarket

3 жыл бұрын

Dear customer, could you please give us the OE number of the ETB and the VIN number of the car?

so if there is a vacuum leak can cause rpm to be higher when idle? i installed new Throttle body on my car and new air intake but the idle is stuck at 1100rpm

@HitachiAstemoAftermarket

3 жыл бұрын

Hello Dear customer, could you relearn the ETB?

@al3zmi

3 жыл бұрын

@@HitachiAstemoAftermarket i did a the relearn the new ETB but it still stays at 1100rpm, that's why i asked if vacuum leak can cause rpm to be higher than normal during idle.

@HitachiAstemoAftermarket

3 жыл бұрын

@@al3zmi Hello Dear Customer, yes if the engine is getting air from somewhere else, that can cause higher rpms.

@al3zmi

3 жыл бұрын

@@HitachiAstemoAftermarket is there any other reason i should be looking at? other than a vacuum leak. edit: I am getting frustrated because with my old ETB i had stable RPM during idle but butterfly valve doesn't fully open because it was broken inside

@HitachiAstemoAftermarket

3 жыл бұрын

@@al3zmi Do you checked the seal? kzread.info/dash/bejne/q6ZpyMuhYtTXe6g.html Also check all the screws and hoses.

Will this work for 2018 maxima

@HitachiAstemoAftermarket

3 жыл бұрын

Hello Bob, if your car has one ETB and it's from Hitachi, this process should work.

Do not work with the Nissan Altima 2015 ? 😢💔

@HitachiAstemoAftermarket

4 жыл бұрын

Dear customer, please make sure, that the ETB you bought from us need this manual relearn procedure. Some of the new ETBs could require a PC to relearn it. Also please check, that before the relrearn procedure you fulfilled all of the required steps.

Hitachi Automotive Systems , hellow can you help me , i cleaned my throttle body of my Nissan xTrail 2.5 2005 QR25 , this video is correct to relearn the throttle body?

@HitachiAstemoAftermarket

3 жыл бұрын

Hello Francisco, please send your VIN, engine code, amount of hp to techsupport@hueco.com

@franciscoartigasgomez1502

3 жыл бұрын

Hitachi Automotive Systems i did it, but the answer it was not good.

@HitachiAstemoAftermarket

3 жыл бұрын

@@franciscoartigasgomez1502 Dear Francisco, Sorry but our office was closed on Friday and we don´t work on weekends. You got your reply today.

@gonzalohernandez88

3 жыл бұрын

No te quiebres la cabeza tratando de hacer este procedimiento que no siempre funciona, mejor llevalo a un dealer Nissan para un mecanico lo haga.

Can this work on my 2007 nissan cube?

@HitachiAstemoAftermarket

2 жыл бұрын

Hello Kevin, as long as the car has an ETB and it's a Nissan you can relearn it this way.

Must be disconnected battery? I did everything without battery disconnecting, it didn’t work. Rpm over 2000 and MIL on

@HitachiAstemoAftermarket

3 жыл бұрын

Hello Tom, you have to follow the instructions in the video. Also timing is very important!

Will this work for a 13 altima?

@HitachiAstemoAftermarket

2 жыл бұрын

Hello Kalie, this should work for your car.

any info for this with nissan versa 2013 ??

@HitachiAstemoAftermarket

Жыл бұрын

This should work with your Nissan.

Does this work for a 2010 Nissan maxima? V6

@HitachiAstemoAftermarket

3 жыл бұрын

If your car has only one ETB, this should work

Will this work on a 2009 g37 sedan?journey trim

@HitachiAstemoAftermarket

3 жыл бұрын

Please send us the VIN of the car to techsupport@hueco.com , we will check it for you.

@swervv2957

3 жыл бұрын

@@HitachiAstemoAftermarket will this work for mine, I have a 08 G37s.

@HitachiAstemoAftermarket

3 жыл бұрын

@@swervv2957 Hello Jay, we need to check the VIN. Send us a mail at: techsupport@hueco.com Thank you

Nissan micra k12 1.4 keyless I have problem sometimes start and sometimes no, and now while make it on fuel pump and throttle doesn't work. Did you have any idea thanks in advance

@HitachiAstemoAftermarket

3 жыл бұрын

Do you checked the ECU for error codes?

@aissamboumaza1643

3 жыл бұрын

@@HitachiAstemoAftermarket yes, I found this one : P1611

@HitachiAstemoAftermarket

3 жыл бұрын

@@aissamboumaza1643 P1611: Immobilizer control module/ECM incorrectly coded. If you had replaced the key housing, got a new key or damaged the key the could be a problem with the immobilizer. Also an faulty electrical connection could be the problem. We hope you can fix it.

@aissamboumaza1643

3 жыл бұрын

@@HitachiAstemoAftermarket yes, that what I'm thinking anyway I'm going now to buy one startup kit ( ECM /BCM /KEY/...) removed form old car and see. Thanks for your contribution

@HitachiAstemoAftermarket

3 жыл бұрын

@@aissamboumaza1643 You are welcome. Keep us up to date on whether the repair went as planned.

dose it work for Hybrid altima 2009 ?

@HitachiAstemoAftermarket

4 жыл бұрын

Dear Abdo please check whether a instruction manual is enclosed with our product. If so, you can use this video.

My car is "push button start" how this procedure work on it?

@HitachiAstemoAftermarket

3 жыл бұрын

Hello dear viewer, use the key button like the key.

Will this work on a nissan versa 2014? Please help

@zolphdiggler

Жыл бұрын

worked on my 2015.

My 2001 Almera stalls right after cold start (starts easily, but stalls immediately unless pushing the accelerator). After a few secs the idle goes stable (~750 rpm). When using the airco the idle goes down to 5-600 rpm even with warm engine. May this procedure useful to solve this? Thanks in advance.

@HitachiAstemoAftermarket

2 жыл бұрын

Hello Tamas, did you checked the ETB? First please test, maybe clean it and than relaern the ETB. Also check for leaks.

IS IT THE SAME PROCEDURE IN A NISSAN CAR WITH START BUTTON?

@HitachiAstemoAftermarket

Жыл бұрын

Yes sir

@luisvilla5490

Жыл бұрын

@@HitachiAstemoAftermarket Thanks in advance, I will do it and comment the results.