💡Fully Restored Antique American Lathe Restore Old Lathes That Have Been Broken For Many Years
Thanks for watching, LIKE, Subscribe & Share!
► Subscribe to channel: bit.ly/3mG3rQi
►Restorations Tools: bit.ly/3J5CVHS
© Copyright by Restorations Tools
I hope you find something useful and enjoy this movie! I am pleased with your feedback, advice and suggestions for improvement.
Пікірлер: 167
Не реставрация а просто косметика, можно было керхером сверху помыть и покрасить и результат будет таким же.
"Fully restored"? Well, I suppose quite a lot of marks for effort in unpromising surroundings, but not really clear what the point was of dismantling and reassembly. Too many steel hammers and drifts. No apparent measurement of alignment or wear. I only saw three bearings replaced, and these had the bejesus hammered out of them. Weird to paint (no filler or primer) after rebuilding rather than before (and two different colours?). The feed gearbox had been full of water but its repair, such as it was, seemed pointless given that the lathe had no apron, feed or leadscrews. Painting the chuck and the cross-slide top surface and vernier controls - why? Toolpost? Perhaps it came otherwise free, and was only going to be used for a single, very simple, task.
@vandalsgarage
6 ай бұрын
they painted the spindle nose, along with a bunch of other machined surfaces. That (useless anyway) end gear banjo needed to be pounded on to the shaft that was covered in a thick layer of paint. It's obvious they have no idea what they're doing. But maybe that was the point, do the worst possible job to encourage people to post comments.
Why don't you clean inside gear case etc nor change the barrings which were obviously worn and in some cases had rust? In fact I wouldn't say you restore it at all just clean and paint. It's basically cosmetic.
@chiroptera6215
Жыл бұрын
There's GOTTA BE...burnt gear oil mixed with steel particles down in that shit from 1969, when it was broken in.🤣🤣🤣
@daviddaddy
Жыл бұрын
Yeah, this was a disaster! They mine as well have just degreased the outside of the machine and paint it! That's basically all they did. I don't understand why go through the trouble of removing all the gears, spindle etc, and not clean out the gear case! And possibly prime and paint inside it, with some good paint that oil/grease won't eat through. I also can't believe they painted the Chuck! And other parts that should not have pain on them! They even painted the Chuck jaws! For crying out loud!!! Lol who does that??? Not to mention the paint scheme was an awful choice! They made it look like a cheap toy! Hahaha.
@robdog7516
10 ай бұрын
I wonder how long it will run before it gets all that crude in the gears that wasn’t cleaned out of the gear boxes. It seems a shame they didn’t clean all that gunk out.
@rapidfire-0680
10 ай бұрын
Thank you for writing all that, I would have written the same, more or less, there's rebuilding, restoring, and overhauling, I would consider what he did overhauling, and you're right, if you're going to go to all that trouble, I would degrease,de rust, paint and replace all worn part's 😮 ! , otherwise it's not worth the time 😮 !
@robdog7516
10 ай бұрын
@@rapidfire-0680 yup. I agree
How on earth did they manage to spread the dirt so evenly beforehand?😂
В колоде даже не помыл, это не реставрация а очковтирательство
It's obvious that you don't actually read these comments, just put a heart by each one. You did less with this restoration than most would have done if they were selling it.
DON'T use steel chisels to dismantle machinery. They damage things. Aluminium drifts will cause no damage and are an essential part of any real engineer's toolkit.
The cross slide and the chuck should not be painted. Also the gearbox is clearly an oil bath type box. Why on earth are they putting grease on the gears and bearings. Without oil submersion, the gearbox will last no time at all. Clearly a bunch of amateurs with no real understanding of lathes or machinery.
AAAAHHH, the pleasure of watching others taking apart heavy machinery using only hammers and bare hands, driven by shear muscle power!
Глядя на такой ремонт, хочется руки оторвать горе ремонтникам.. А маляра прибить на месте...
@user-kw5xj4fo9v
Жыл бұрын
п ляяяя... детали приработавшегося механизма скрести железной щеткой - вал ошкуривать... капец агрегату. теперь у него допуски - плюс-минус лапоть по карте, биений естественно "не будет", соответственно и сифонить смазка не станет, фонтаном забъет. ремонт - сказка
@user-kw5xj4fo9v
Жыл бұрын
мастера! как подшипник то посадили! волшебно!
@user-dv1rg7oq5r
Жыл бұрын
Главное патрон и шкив покрасили .
@bojarinas1965
Жыл бұрын
Ja swarschiku ruku slomal by nakum
@barrytaylor8422
7 ай бұрын
Thank you
Clean first! Then disassemble, check all gears, shafts, bearings, ETC and replace as needed. You add more dirt to the internal parts the way you did it. Why was the tail stock so new looking!
tienes razón es una limpieza simple me e dado de cuenta que el trabajo de esta gente es importante pero sin saber aplicar la verdadera experiencia y mecánica. Deben prepararse mejor para el éxito la escuela.gracias por el esfuerzo sigan adelante.saludos. yo soy ingeniero mecánico y estoy listo para ayudar.
Лутше бы продали под нормальный ремонт, а так видео нормальное, показывает как не надо делать 😂
@user-lr2vd1te7t
Жыл бұрын
Да норм видос. Все шестерни и валы помыли, еще и солидолом смазали. А внутри корпус незачем мыть, там же солидол а не масло)))
@VOLK-68
6 ай бұрын
Такой ляп) Станок специально обсыпали пылью. Стена чистая в начале видео, только станок грязный стоит) Винтики все откручиваются с руки. И там тоже лайки нужны.
Restoration videos are capable of evoking feelings of nostalgia. They remind us of the craftsmanship and attention to detail in the past 👍👍👍
@kirksnyder6190
Жыл бұрын
Exactly. What's worse we as a so-called intelligent species are forgetting HOW TO CREATE and make things from scratch or ingenuity.
@barrytaylor8422
7 ай бұрын
It dont take much to impress you
Советские станки в несколько раз лучше американского хлама.
With such a disassembly, the bearings are changed in a mandatory manner, even if they seem normal (too laborious to replace bearings). The bed must be milled (as a rule, a significant development is formed in the center).
@olivierfu7778
Жыл бұрын
Non pas fraisé mais rectifié au pire au mieux gratter avec instrument de mesure precis et il y en a pour beaucoup de temps
Why do you not clean it before you take it apart?
@benniehazelwood9276
4 ай бұрын
I ask the same question to.
Как приятно видеть, когда человек производит ремонт любой техники для себя. Он может себе позволить оставить грязь внутри корпуса техники. Производить покраску корпуса только в полной сборке аппарата без обезжиривания, без грунтовки, чтобы все трущиеся детали имели сопротивление. А как классно оставить шестерни без смазки (надо было ещё песочком их посыпать 😅😂🤣). Во всём только одни плюсы.
FIRST, brush clean the outside to avoid any dust and grit getting into gearbox etc when opened.
Well, one thing I'm learning for sure from these restoration videos, is that unless you have the time, money, equipment, need and skills, it's better to buy new or gently used machinery. However, restoring machinery is for sure an enjoyable process 😉
Thirty-seven minutes and twenty-six minutes of travesty upon travesty. I may never recover.
It hurts to watch you bash in all those expensive precision parts and destroy them only to put a coat of paint over it
Хитрый реставратор! Облил станок жидкой глиной - как бы он очень ржавый, и почистил его... (на полу под станком - куча глиняных крошек, а сзади станок - совершенно чистый...) Некрасиво обманывать, товарищ!
@kajoulukajoulu1513
Жыл бұрын
Il fallait juste le nettoyer alors car le remontage des roulements au marteau 😢😢
Magnificent job you did restoring that lathe to working order. You put in a lot of hard work and sweat to clean all that rust and dirt off. It looks much better too. Great work.
а нахера было переберать коробку подачь, если ни фартука ни валов нету. хоть бы шабер в руки взяли для вида.
*_Super-impressive, fascinating, satisfying, and just beautiful to watch. Great job!_*
@RicktheRecorder
Жыл бұрын
Ironic?
Ainda bem que pintou de verde agora joga no mato pra ninguém ver
Trabajo mal hecho, las piezas se lavan con acetona, y no se cepillan, y no se trabaja en el suelo, para eso hay banco
I am amazed that he didn't wash the inside of the gearbox housing and change all the bearings. I am not impressed!!!
As I'm watching the feed gearbox come apart I'm thinking to myself "that's never going to work properly again". At least that would be the scenario if I was the one doing it! 🤣 Didn't appear to be hooked up though, so probably moot. I enjoyed seeing the insides of one of these units. Thanks!
Wonderful, i love Lathe.
I don’t know if using an hammer is the best way to install ball bearings
@itarry4
Жыл бұрын
Yhea well he's not really restoring it at all. Some of those barrings need changing, no ensuring the bed is level, no cleaning inside of anything not even inside the places tye axles go through. It's purely for looks just to sell it to someone who won't know how badly the restoration has been done. If I bought it I'd be really annoyed and it'd need taking apart again and doing right.
@u.blitzknaller8978
Жыл бұрын
@@itarry4 It is exactly like that
Так этож 1616.У меня такой 1952г.Динозавр!
that little flatbed truck looks so handy, why dont we have those here
Чего сразу снаружи не почистить? И охота в такой грязи ковыряться? Капец...
Покрашеный патрон это вообще огонь,ладно хоть призмы не покрасили...
Has tenido mucha suerte de que este torno estaba con solo aserrín de madera pegado encima. Solo tuviste que lavarlo y armarlo. No ví nada de verificar la geometría, paralelismo, concavidad o convexidad del recorrido del carro transversal, rasqueteo de los prismas del carro principal, etc, etc.
без шабрения это не ремонт , а так , пыль сдули.
Excelente!
Aw man,...this was painful to watch.
Курс молодого токаря....сначала пыль бы сдунуть сжатым воздухом или керхером пройтись😮
@doodiik
8 ай бұрын
Механик за сдув воздухом, шланги рубит убирать только щеткой.
After finishing, so noisy, means the most of bearings are worn-out. Also, gear teeth have the worn-out having gaps. The transmission gear box might be the type of filling machine oil that prevents noisy gearing sound and easy gear shifting.
The life expectancy of this lathe has just been dramatically shortened. It would have been better to thoroughly clean it, fill the oil and then change it a couple of times after shortly running it. I don't believe t has oil in it now, at least it doesn't sound like it does and having watched the disassembly and recently it looks like the oil feed from the sump no longer exists. Though I could be wrong about everything...
والله انتم بارعين في التصديح❤
I wouldn't want them working on my lathe.
Should the lathe be used for drexing wood? Because important parts are still missing, e.g. the box under the support where the gear for longitudinal and lateral feed is located, as well as the pull and lead spindle (for thread cutting) as well as the on and off shaft, and the tool holder with small support (for that taper turning) I see something like that straight away because I come from machine tool construction (industrial mechanic - repair) and also work in that area
Muito bom
@restorationstools6447
Жыл бұрын
I am very happy to receive your feedback, advice and suggestions to improve myself more and more!!! Thanks for watching and supporting me. Thanks a lot!!!
This is not a restauration. The number 1 thing you need to do with a restauration is to check the wear on the bed/ways. Then grind/ scrape them in.
@vandalsgarage
6 ай бұрын
The fact that they didn't attempt to scrape in the bed ways was the best decision they made. Too many people have no idea how to scrape in a machine, and cause more damage. Its not just a matter of getting it flat, or even matching the mating surfaces, too often the geometry is changed by amateur "restorers" who don't have the proper tools to measure and correctly address bed wear. The result is just more added wear to the bed ways. Even if its "flat", it may have lost orientation.
Change the title to "I make this lathe beauty again,and i dont care if it's work perfect or not. Just for content mate"
@restorationstools6447
Жыл бұрын
I am very happy to receive your feedback, advice and suggestions to improve myself more and more!!! Thanks for watching and supporting me. Thanks a lot!!!
фуфло
да со шланга водой обдать, и всех делов
Видно что станок в хорошем состоянии, чем-то заляпали
@VOLK-68
6 ай бұрын
И я про тоже) Стена чистая в начале видео. Обсыпали специально)
Waist of time
With respect to some of the comments, even for restorations for anything, 90% IS cleaning off the grine to see what needs to be fixed. So its still a restoration since it was non-functional and missing some components.
Amazing video
La señora de la casa , cuidado con las plantas eh bueno ya se lo dije
belle restauration mais, il manque plus de la moitié du trainard : partie inférieur avec les manivelles , les manettes d'automatique, manette d'embrayage de la vis mère, le chariot transversal, le chariot supérieur et la tourelle porte outils. ensuite, pour faire fonctionner tout ça, il manque aussi la barre de chariotage et la vis mère. vous n'auriez pas dû monter les ensembles de pignons de la tête de cheval( poupée fixe) avec de la graisse, ainsi que la boite des avances / filetages . ce sont tout deux des organes qui fonctionnent par barbotage dans des bains d'huile. en un mot, dommage pour vous mais ce tour n'est absolument pas fonctionnel.
Dikkat! Çekiç ile rulman takılmaz! O rulmandan hayır gelmez!
Przepięknie jest ta to kareczka odrestaurowana a czemu ona nie nie toczy teraz po remoncie pozdrawiam serdecznie. 👍👍👍👍👍👍
what are you restoring? i know at first glance it looks rust covered. but that lathe is in perfectly good condition, just blow the saw dust off of it.
Nice work
Beleza
As good as new Gov, honest to God *fingers x-ed behind back*
Le faltan piezas para q pueda trabajar el tornillo patron y la torreta porta herramientas x la cantidad de engranajes tiene q ser caja norton y la caja de engranajes lleva aceite se nota q tiene una bomba de aceite
Painful to watch. That headstock should be part filled with oil, the gears and bearings will quickly fail.
You fix it with a lot of effort. You didn't clean the gearbox interior well and you should have put gear oil in it. Grease is not enough.
This was hard to watch, there is many areas of improvement to be learnt, if your not going to change bearings then learn to pack bearing with the grease and use bearing grease not general purpose. what about using Loctite on grub screws. you need to Lubricate gears. learn to use proper tooling, if you cant buy, then make it. like what other people said Clean everything. You have skills, Don't do a 50% job.
@RicktheRecorder
Жыл бұрын
It's a semi-pressure lubricated headstock. Pity they didn't use any lubricant.
You should have just washed it or better still don’t put sand on your lathe in the first place
good job looks great
Restoring is not the word I would use, more of a disassembly, clean and reassemble.
Pourquoi vous faites faire ça par des bûcherons?
Restorasi? Itu hanya membersihkan saja
Nice
👌
покрасил и помыл. Никаких пласкостей корче шлак
Полная хрень я тут вобше неувидел реставрации в каком состоянии станина может она вобше выработаная а разобрать покрасить и я смогу а вот пришабрить направляюшие очень большая работа сам занимался этим а вот это самая маленкая часть навести красоту
@alegator
Жыл бұрын
Какая к черту реставрация)))) Это модернизация системы смазки перевод с масла на консистентную смазку))))
Harmering every where, not cleaning the inside of gearbox ; Basic Knowledges you have to apply, ball bearing is very High presision mcanism .
У нас при СССР в колхозах так ремонтировали.
ужас
Why didn't you clean the inside of the gear box
This is NOT RESTORATION, it is a joke. No inspection and replacement of bearings, no lock wires replaced on location screws, using a large steel mallet on removing and replacing precision parts. Not cleaning the inside of the housings, painting over all external surfaces. Using a rebar chisel to remove parts. Basically you are committing fraud by stating that this is a restoration, it is an insult to the engineers that built the lathe originally. 👎👎👎👎👎
No me gustó pudieron limpiarlo y pintarlo mejor
#1 that is not an American Lathe, it is Chinese Missing are the lead screw and feed screw, the apron, the second set of jaws for the chuck, the compound and tool post. It will never cut metal and appears to be used in a woodworking shop. He left out the oil pickup pipe for the pump and the key for the tapered chuck mount. It could be of limited value there because wood lathes use different chucks and generally have a larger swing.
It must take days to get that uniform rust over the whole machines.
Lack of experience opening
Why would start pulling it apart before you cleaned the outside? Basic common sense.
I agree with@itarry4 this isn’t really a restoration project. More like dismantled cleaned up and put back together. No new bearings didn’t clean the inside when the gears were removed. And then just spray painted over with no primer. So give it 6to 12 months and it will start pealing . Granted no got the tools but a decent attempt
Why would you even think of opening the gear box with all that crap still on the machine. It is like performing surgery in a pig pen. Not to mention the painful whacking of precision ground steel with steel hammer?
Nhìn làm chán. Toàn cắt video cụt lửng
How do you remember the correct order of all the gears?
@markB40
Жыл бұрын
Look back on the video
@vandalsgarage
6 ай бұрын
Video, still pics, and maintaining order on the bench while its coming apart. These old lathes have pretty simple gearboxes, both the headstock, and the feeds gearbox.
Wasn't it suposed to be filled with SAE 90 oil?
They would not touch any of my machines Ever nor would I buy a rusty screw from them.
That rust doesn't look genuine
@rabindradas4423
Жыл бұрын
It's dust.
@RicktheRecorder
Жыл бұрын
I think it's a KZread restoration technique. Spray the object with thin oil, then sawdust.
Way to much unnecessary work. Should of just hosed it down, cleaned the inside and added fresh gear oil and put it to use. Just saying!
Lagabunzia ertofia, sileprante!!
33;38 !!
Very exciting new video with great work and new tools...good job guys...you are the best🛠️🛠️♥️♥️♥️👏👏👏
No one part of this lathe was restored. Just ugly paint...
when you see the "brand new rust" you know it's gonna be bs
За такую работу нужно руки оторвать а ваш молоток без смазки в одно место забить.