Thank you! Not only did I save on a repair bill, I found $22.94 in change in there.

@8-Bit_Flashback

3 жыл бұрын

Sweet

@jameshorton1416

2 жыл бұрын

"""..

Thank you! Our Frigidaire front loader left the clothes soaked after the final spin. Your directions were clear and easy to follow, and I fixed it myself in about 45 minutes. I followed your instructions, cleaned the completely clogged trap, and now the washer works great again! You saved us a lot of money. Thank you so much!

@D.I.Y._All-in-One

2 жыл бұрын

Glad I was able to help out and good job on your repair.

@ericaschannel2599

5 ай бұрын

Exact issue I am having rn

Just when I was about to have to spend $700 for a new washer, I found your video. Cleaned the trap, which was completely clogged, checked the pump as you showed and washer is working great again. Putting the hose clamps on was a little tough, but hey, no expense, just a little time. Thank you sooooo much for this video.

Just wanted to add my thanks to the others for this video. I followed your instructions and found the problem in about 10 min. The washer is back to working like a champ. Thanks for saving me all that time and money!!

Great video! Best video. All the others showed removing the top and front panels, even the rear panel. Entirely unnecessary. This is the best video. Do this one! Remind me, next time I buy a damn washer to buy a model with the front access panel at the bottom to these common drain fixes! Many have them. Lol. Makes this a 60 minute job rather than 4 hours, and ya don't have to move it anywhere. Even if it costs $150 more it would be worth every penny! Ours lasted 8 years before getting clogged. When the kids started doing laundry on their own in the last 2-3 years, that's when it got clogged of course. Kids are HiGh Maintenance!!! Lol

Great Job.. well spoken, detailed and to the point.. not some long winded person.. thank you .. fixed my washer in 15 min..

@D.I.Y._All-in-One

6 жыл бұрын

thank you

Thank You !!!!!!! My wife had put some 4 x 6 inch makeup cleaning pads for her face in the laundry , they had little loops to hang them up that got sucked between the gasket and pulled the whole pad in . Two of them were very neatly stuffed in the filter , Oh and thirty seven and 1/2 cents , one of the pennies had a rough time .....

You my friend are a lifesaver! The washer is runner just like a new one. The hardest part was getting the Stank off my hands after washing out the basket. Thank You

Thank you! Twenty minute job. Well made video - quick, concise, clear. My symptoms: Stopped in the middle of a cycle and water would not drain. I could start a new cycle, but no water drained or was added; the drum would spin for 20 seconds and stop. In a few minutes all the front lights would simply go out. (Frigidaire Affinity that is about 8 years old)

@russiangirl532

Жыл бұрын

Hello did you fix it having same problem?

Thank you for all the details explaining each step and the clear quality video. Also, appreciate the explanation of how you diagnosed the issue and the correct repair. I watched another video stating it was a faulty door lock. I changed my door lock and the washer still did not spin. After seeing your video I knew this was the issue. I did not have time to repair it myself, but you saved me from getting gouged by the appliance repair company! I was an informed consumer! Thank you

@yvonneramirez5888

2 жыл бұрын

i will attempt this today - normally i call a service guy out i totally agree with you.

Thank you!!!!! Worked like a champ. 13 yr old machine spinning like new again. While in there I also found one of the struts had come detached and reinserted the plastic pin.

3 months ago my washer started having problems with the spin speed and water not draining, about a month ago i was fixing to buy a new washer and by luck last night i came across this videos. Well am happy to report that thanks to you video now i have a working washer and no out of pocket money for repairs or a new washer. Great video.

@D.I.Y._All-in-One

3 жыл бұрын

Great news!

Thank you! Our Frigidaire front loader stopped spinning out and draining a few days ago. I came across this tutorial, shared it with my s/o, and we tackled it today. It was indeed clogged, but not with a ton of dirt and debris - there were two reusable cloth masks; one was in the hose and one was in the trap! Saved us a bunch of money that would’ve gone toward a repair service or replacement.

You are a life saver my man. Easy to follow, well articulated instructions 👌🏾👍🏾

Like many others here, thank you for posting this video! I had same problem as the final spin was no more available since a few day with my Frigidaire washer. I did tilt as you showed us and was able found a large piece of clothe inside the drain blocked by the filter. it was really easy and simple to get my washer operational again! thanks a lot.🙏

After hours of frustration and replacing the drain pump, I found your video. I did just as you showed and holy cow, that drain basket was a big plug. After cleaning that out I put the old pump back on and everything works fine. I will be returning the new pump in the morning. Thank you for saving me $100 bucks on the new pump and who knows how much on a new washer.

Very helpful video. I cleared my drain hose on the back. Didn't work so I will now clean the trap as you showed here. Did not know the thing even existed until I watched your video.

@D.I.Y._All-in-One

4 жыл бұрын

Glad it helped

Nice job! I'd done this cleanout on our previous frigidaire front loader that had a lower front access panel. That one had almost $10 in change in the trap. With the exception of the added "debris catcher", this pump looks very similar to the pump on the earlier model. I'm not all that thrilled with the "new and improved" one piece front panel on this washer, but your video was a big help toward solving my problem. Thanks!

Thanks for this awesome video. I impressed my husband by fixing it nearly by myself (needed a second pair of hands for putting back together -- the clamp squeeze hose dance was a bit of a pain!).

Great Video! Very thorough. I will clean this all out tomorrow. You made it look pretty simple to clean this out. I am anxious to do it to see if it resolves our issues for the drum not spinning.

Thank you for a quick video that helped to resolve our issue. We had the E20 error and an appliance tech did a diagnostic and said it was the drain pump motor and it would cost $455. We did it ourselves with your video. A rag similar to yours was found, no money was found.. It took us longer to clean out the pea trap/accordian part was full of debris/dirt from rugs. Getting it all back together was challenging and took a long time. We used worm clamps instead of the included ones and that helped a lot as the green ones were tough to access, get off and put back on. We also used a bit of oil on the tubes to get them on tight with the new clamps. We saved money $ and I let the appliance repair company know the motor was never the issue. Shame on them. Just did two loads of towels from cleaning up and drainage. Worked great.

@D.I.Y._All-in-One

3 жыл бұрын

Glad it worked out.

Thank you for posting this DIY Had this happening to my washer. I watched your video pulled out the trap and it was plugged. I did have a hard time getting the clamps out and back in. My boyfriend bought the standard hose clamps and made it easier to reassemble

Thanks man! Seems to have fixed my washer although you make getting that trap out look very easy 😆.

So many videos on this going by the front and having to remove the front panel, then extremely awkward reaching screws, clamps, etc. Glad I kept searching and found your video ! I will be trying this soon..

Wow. You just saved me big $$$. I followed your instructions exactly when my washer suddenly stopped filling with water and not working. I looked into all of the reasons that it might not be working first, checked out the washer manual, and then found your video. If anyone reads this, I am a middle aged woman who had to flip the washer on its' back,(no front panel, of course) to access the drain. Not fun, but it is not ridiculously heavy, so it was doable with care. Getting it back up was a little more challenging. Ladies, you can do this! By being slow and patient with the instructions, I loosened the clamp, wiggled the trap out, which was jammed full. My trap was chock full of rubber pieces from a floor mat that I had put in the washer! I cleaned it out, (trash barrel and washed it in the sink) worked the trap back in as instructed, and then ran a sanitizing cycle and then a delicate cycle to make sure everything was working and draining. Seems to have done the trick. Thank you so much for this excellent video and your spot on instructions! Yay! Lesson: Washers are not indestructible. Never again will I wash one of those mats in it!

@D.I.Y._All-in-One

7 жыл бұрын

Stay D. glad to hear you got it fixed. Thanks for watching

THANK YOU! This is why my washer stopped spinning. WORKS GREAT NOW!

Thank you Sir! Your video was great n on point. You have earned a like and subscriber. Evil beings were trying to mess with my washer. You have saved me. I am currently enrolled in a program to get a New career. We are required to wear Business attire. It’s summer time now in Ny. I’m going to perspire. I have to study for my class. I didn’t have time to go the laundromat. You have saved me time and energy by draining the drain on the washer training. Thank you from my whole heart. 👑🏆🏅for you!

Really great video, it gave me a really good overview of what I was getting into with this repair.

Thanks man. Had seen other videos about taking top and front panels off. Didn't want to go that route. Glad I found your video.

So helpful! A real pain to do but so far so good! Great video footage and much more helpful than the other videos that suggested taking off every panel to access!!!

Thank you - Saved me the cost (and hassle) of a new machine.

Thanks for the tip about going from underneath! Took the whole front off last time! This worked great!

@headamuse

6 жыл бұрын

Charlie Runyon my dryer is ontop of my washer...is it possible to take the front off of the washer without access to the top of it?

I never comment on videos but OH MY GOSH THANK YOU. This saved me from buying a new washer.

Totally saved us a lot of grief and money! Thank you!!!

Wow-- Best youtube video EVER-- thanks so much.

Bro, this video was spot on to my problem and solution. Thank you for making and posting it

@8-Bit_Flashback

5 жыл бұрын

Your welcome

Thank you just saved so much by trying this today. Had my bank card change and junk in their. Life saver!!

WOW, THANK YOU SO MUCH... I WAS GOING TO BUY ANOTHER WASHER...LOL YOU SAVED ME A TON OF MONEY..

I never comment on videos but thank you so much for posting this. You probably just saved us hundreds of dollars.

@D.I.Y._All-in-One

4 жыл бұрын

Your welcome

THANK YOU for this video! I couldn’t get the boot off all the way, seemed like part of it was attached to something else (besides the drum) that I could not see. Trying to get the trap out, I felt a cloth. It was a sock! I couldn’t get the trap out due to whatever the boot was attached to in back. But I felt around inside and didn’t feel anything else. Getting the boot and clamp back on was a B* for me, but I did it! 3 loads in and no leaks and it’s draining again!! Thank you!!

@punknhead23

Жыл бұрын

Way to go Daisy. Going to have a go at mine tomorrow. I've already replaced the door latch mechanism. It worked great for 6 weeks now again with the No drain no spin.

Excellent DIY presentation!

Thanks for the video. When I saw the rag, I was yeah sure.. I had one.. Change, screws and a bit. I had to go from the bottom also as mine are stacked.

Thanks for the simple, clear instructions! Found a lot of change, fortunately the trap wasn't as full as the one you showed so we felt that we didn't need to investigate further! Unfortunately the washing machine is leaking right now (I guess the boot wasn't put back on tight enough :(( ) but it is spinning beautifully again.

@D.I.Y._All-in-One

3 жыл бұрын

Glad i could help

Best video I found for this. Thank you!

You are amazingly clear! Thanks for publishing this online.

@D.I.Y._All-in-One

2 жыл бұрын

Thanks for watching!

Vacuum out the tub and drain hose with a shop vac. That removes about 3/4 gallon or more of water. Then pull washer out about 2 feet, tilt it back against wall, stuff a large towel in the bottom-back and under the boot area and access coin catch boot by removing only the largest top retention ring. Fixed with clean-up in an hour and much easier. Usually the pump is not the issue. Tip: don't fill the washer with small items and large items, and don't stuff the small items to max either. The large items or overfilled washer tub will work small things like panties and small socks thru to the coin catch. That's what was in mine, clogging it...panties and a bikini top pad lol.

thank you so much saved me money for a easy fix washer works great

Thanks! That's exactly what is was. I had ordered the door lock assembly prior to watching this video and after fixing immediately cancelled that order.

@D.I.Y._All-in-One

6 жыл бұрын

Glad to hear you got it fixed.

This is a big help for me. Thank you! Having a hard time getting the coin holder back in but i will. Thanks again

@D.I.Y._All-in-One

2 жыл бұрын

Your welcome

Man that was a very helpful video. Thank you! Lafayette, IN

@D.I.Y._All-in-One

5 жыл бұрын

Your welcome

This was great thanks so much. Somehow a couple socks managed to get into the trap in our machine. With this video was like a 10 minute job. Very clear and easy to follow.

@D.I.Y._All-in-One

7 жыл бұрын

glad to hear you found the problem .. thanks for watching

@sebastiansosa4435

6 жыл бұрын

The hard way was to move the machine to access to the bottom opening. After that was a little complicated. The filter was so dirty. But my machines is working like new. Thanks !

@punknhead23

Жыл бұрын

So that's where all the socks go! I was always blaming the dryer...🤔

Thank you so much!!! Extremely helpful

Thank you so much. My apartment maintenance vacuumed only... I did it myself and found a whole ass rag in there.

@D.I.Y._All-in-One

3 жыл бұрын

Glad you got it fixed.

This video just saved me so much trouble!

You just saved me a service call. The thing drains and spins great now. Thanks !

@peterdembowski6402

5 жыл бұрын

I cleaned out 5 coins, 4 bobby pins, a political pin, a button, and a rubber drink coaster.

@D.I.Y._All-in-One

5 жыл бұрын

nice!

Thanks for your excellent video. I had to completely remove the boot to get the trap out but not only did I save money on the repair but I also found $7.51 thank you.

@D.I.Y._All-in-One

6 жыл бұрын

Glad it helped you out and made you some money. Nice!

Having same issue. I pulled it apart yesterday and the basket is missing. The only thing in the boot was a bunch of change and a key. The upper, small hose clamp is a PITA to keep clamped while sliding the boot into position. Thanks for the video. Cheers.

thank you .i was able to fix my Frigidaire Affinity.

This solved my problem. Thank you. Also got paid for my work, 2 dollars in change. Some bra pads and and old Nintendo DS game

Another thank you for keeping me from having to drop a thousand bucks on a new washer

Great job. It took 20 min almost to take out 1 bowl of clog. It started spinning. Need to wash my hand to see how much cut i got 😆

Great video straight to the point

Well, wonderful. Washers, draining and operating quietly. Should of done sooner, laundry room stench gone. Thank you

Thank you very much ,you saved me a ton of money.

Wow thank you, I think this is the same problem I’m having. Gonna try to do this today

Thank you for such a clear tutorial! Unfortunately this is the SECOND time I've had to do this procedure in just six months time, and I don't have the easy access panel. Frigidaire - shame on you for designing such a horrible piece of crap machine that requires tipping every six months in order to access that filter. RIDICULOUS!!!!!!!!

@Cndfirr

4 жыл бұрын

Laura Querry - your better option is to make sure and check and empty all pockets before every wash .... every pocket every time before every Wash ..... much easier than tipping your machine back and opening it up every six months

@juanakatony1

4 жыл бұрын

I was thinking on how to say it without you taking it the wrong way but I was glad to see Frank had already said it. Also after 6 yrs I’m doing this for the first time. You just might not be used to going thru your pockets. Shaming Frigidaire is kinda like me saying “these stupid GLAD garbage bags suck. They get full so quick!”

Thanks saving my money and time

Thank you so much this worked perfectly. And I found $3 in change 😂😂👍👍

Thanks for the video my washer is having the same symptoms not draining & the water stinks bad. Gonna try to repair now... thumbs up 👍 👍

@D.I.Y._All-in-One

6 жыл бұрын

good luck hopefully this solves your problem

@bbperez6361

6 жыл бұрын

C.L.S. Allinone thank you I actually have my hands full with my washer. The door hinge is loose so I accidentally broke my strike AND I need to clean the trap lol 😯 but thanks again for the video. Very informative

@bbperez6361

6 жыл бұрын

C.L.S. Allinone instead of messing with that ring clamp you think a hose clamp would work the same? I'm having so much trouble putting it back on

@D.I.Y._All-in-One

6 жыл бұрын

yes a hose clamp will work just be careful not to overtighten it

@bbperez6361

6 жыл бұрын

C.L.S. Allinone thank you. You wouldn't believe how many hours I was messing with that ring clamp. The washer was given to me used & some screws were stripped out so I couldn't take off the housing to get to the pump. I had to work through the opening on the bottom. Which made it nearly impossible to put the clamp back on. Was even hard with a hose clamp. Such a hassle but I got it. I'm washing my first load now to see if all is well. Thank you a bunch 👐

Thank you for this video

Dude, AWESOME video with great visuals and precise instructions. I will definitely be subscribing 😎👍

@D.I.Y._All-in-One

5 жыл бұрын

Awesome

Thank you!!! This worked!! I am now trying to figure out what to buy with the $0.61 that I found in the trap filter!!

@johng5122

2 жыл бұрын

LOL...I need to go count my earnings now...

Fixed it. Thanks

@nossfried

5 жыл бұрын

Thanks for the clear and easy explanation. Took a little time and patient with such a small work space but it did the trick. Instead of spending a lot of money, I made $2.27!

Best video...THANK YOU saved my ass!

@D.I.Y._All-in-One

6 жыл бұрын

your welcome

@naomisignatureshaka2232

6 жыл бұрын

Real talk, my plug was clogged with some other level shit...glad i saw your video...keep doing what you do!

@D.I.Y._All-in-One

6 жыл бұрын

thank you. mine is actually do for another cleanout again..

Question: would it be easier to just unscrew the whole bottom panel to have broader access to the pump? Or will that dissemble the machine and just make things more complicated.

4 screws on the impeller pump, the forth is hidden under the plastic top cover

C.L.S Allinone, When running my normal, bulky, or other cycles on my washing machine it works until the final spin. The machine does not complete its cycle, it stops before rinse and spin, I have to shut it off and manually put it on rinse and spin to dry the clothes. Since the machine is in fact able to do the final spin, do you think it is a matter of a clogged filter/pump/hose, or maybe something electrical? your advice will be greatly appreciated.

This is the second time i've had this adventure...not such a big deal other than those bloody clamps...I'm replacing all of them with stainless hose clamps next time I go in...!!!

I have this one ! Do u like if u can replace the front rubber part that’s very mine is so moldy and gross even e cleaning

ok I'll try it

I will definitely try this. But I am a bit confused. Why will the washer suddenly spin faster if the trap is clean? My washer spins a little bit, but does not get up to full speed.

@D.I.Y._All-in-One

6 жыл бұрын

because the washer is full of water and the load is heavier so it is unable to spin fast until more water drains out.

Hi do you still read and answer comments for this video ? If so I have a few questions but it’s not about an Affinity but just the one that says Frigidaire with a digital panel .

I'm about to tackle this myself. However, the hoses at the back are too short to tilt the whole thing back. Is there an easy to disconnect the hoses from the machine itself or do I need to do this where it connects to the water source?

hi all, my washer machine still has the light on but it did not work, no spin. I did check the belt, it is ok. do you know why?

Ok question we have cleaned trap n pump is good but still not spinning/spinning fast when it gets ready to drain it spins one way then other slowly back n forth few times then unlocks door wats the problem

What else might a draining and spinning problem be? I cleaned the trap and that is not the problem.

@Cornerstandoutdoors

2 жыл бұрын

Same here it's spinning but not fast water pump on mine seems little slow

@punknhead23

Жыл бұрын

Door latch mechanism. Many videos on that also.

I cleaned out the drain and checked the pump it still does not spin fast on its final cycle. After a few loads of clothes the water will not drain again. Do I need a new pump and door lock?

@D.I.Y._All-in-One

7 жыл бұрын

FilthySwagProduction sounds like the pump to me . also check all drain hoses to to make sure there is no clog

hey we just disassembled ours and remove a pair of undies then reassembled and machine still won’t work :( is the impeller supposed to spin and spin very easy? because ours will turn if we do it but then it kinda feels like a rubber band inside as we turn it springs forward sorry it’s hard to explain.. any advice please

@peterconnolly2724

5 жыл бұрын

The impeller should rotate smoothly without much effort. I'd take the pump out for inspection and (if needed) replacement.

Should the impeller in the water pump spin freely? Mine has some resistance.

@D.I.Y._All-in-One

7 жыл бұрын

Amy Erickson a small about of resistance is normal

I did all that now the door is locked and it keeps humming. Any thoughts?

Front Loader that spin to fast what would that be

👍

Was there a error code you got with this issue? I'm getting f53 error.

I have the same one but how do I remove the dryer from top of washer?

@D.I.Y._All-in-One

7 жыл бұрын

Benika Williamson there is 2 screws on the front of dryer towards the bottom and 4 screws on the back towards the bottom after those screws are removed they can be separated.

I'm having trouble with my washer. Did anyone have issues with the washer stopping mid cycle? and did these steps help?

@D.I.Y._All-in-One

7 жыл бұрын

Rakesh Kler Mine would stop during spin cycle or spin cycle would go really slow.

My problem is the sensing light is not working on the panel

But my washer still not spin at a high rotation

My washer just indicates spinning. And no movement

EEEEEE........ My model is not the same, problem is same...☹️☹️☹️