LOL, that torx screwdriver. Pretty neat tho.

@metaxa715

5 күн бұрын

torque turn

I never saw the inside of a compressor.what a lucky I saw this vid!

I don’t want to hate on the guy, but I didn’t see the guy fill the pan with oil, resurface the armature, or replace the brushes, and like someone said, the bearing. This isn’t going to last very long. But I like I finally see what is inside one of these.

@ramtek2702

11 күн бұрын

Well, he did a nice paint job & added some misleading labels.

@bertiesworld

8 күн бұрын

Replace the brushes? There aren't any. Rotor was probably good even though it had scuff marks on it. It looked like he had the stator rewound. Bearing, being in oil, he might have changed it or he might not have. But it comes down to cost. Just breathe in the paint fumes! Over the years, I've seen some amazing repairs in these out of the way places, whereas on home turf, we'd just bin it.

@TheRobWay1

6 күн бұрын

Rotor, not armature

@cornwallav8r

4 күн бұрын

@@bertiesworld so all it needed was a pair of gaskets.

@tonyfrewin4822

18 сағат бұрын

Armature and brushes are very hard to find on a hermetic compressor 😂.

I have so much respect for these people who actually fix things instead of just being parts changers. And with conditions and equipment that would make people in this part of the world cry like babies. There's never a shortage of comments from the safety na2i's under videos like these.

@MK-xl9tt

5 ай бұрын

Agreed I’ve been in the hvac industry for 30years and never have I seen a compressor repaired, it’s scrap metal. I will say the labor involved to do this would probably out weigh the price of a new compressor especially with having to weld it back up and if the union is involved. That was some good efficient workmanship we just watched.

@jnhook8086

2 ай бұрын

It's not like people wouldn't be willing to do this in America lol.. it has everything to do with cost of labor

@bertiesworld

8 күн бұрын

@@jnhook8086 And with a new compressor you get a manufacturers warranty. Even the 11kw motors we use (much bigger than shown here) are no longer repaired. The cost of taking it apart, fixing the fault just doesn't make it cost effective - a faulty bearing we might change but again if the rotor has been hitting the stator - not good. Far cheaper to just get new.

I’m sick of living in a country of people that throw out $3,000 refrigerators when the little round black $2 capacitor goes bad. But I found a niche. I visit my local scrapyard once a week to look for old tools, appliances etc and I fix them to like new quality for literal pennies in parts and a bit of elbow grease. I have great satisfaction in using old snap-on wrenches and power tools that were rusty in the garbage and I polish the chrome like new, I also use those found/refurbished tools to rebuild small engines and motorcycle engines I find there and I sell them back to the people that scrapped them for a hefty profit (think of the soap in fight club) Everything I buy there costs me $7.50 per 100 lbs.

@_..-.._..-.._

4 ай бұрын

Hint: any device that makes heat or has high amperage use that stops working 90% of the time needs a $0.50 thermal fuse. They make many non-resettable so you’ll throw it out. Heat guns, hairdryers, vacuums etc.

@Jack_all

3 ай бұрын

move to India

@brankelly1921

3 ай бұрын

Beautiful comment! I agree with you but more so on the company's design side. They design to throw away. Apple being the biggest criminal. We need more people like you and the uploader! Engineers need to be more responsible.

@jnhook8086

2 ай бұрын

Lol I highly doubt the people who threw away equipment are paying a hefty amount to buy it back from you. Those people already bought a new one

@justincase4812

Ай бұрын

​@@brankelly1921That's not an engineering problem. That's a shitty component that production decided was cheaper or "good enough"

а с какой минуты начался ремонт? и когда закончился? я что-то пропустил!)

@user-ty5qy3iu6n

Ай бұрын

единственное что заметил, это замену прокладки на крышке клапанной доски.

@user-tf6kz9sd3h

Ай бұрын

А додуматься никак?вот вы и мастера такие,все им покажи,не бросайте работы!Люблю переделки по двойной цене😂

@boriskruglov6785

8 күн бұрын

@@user-ty5qy3iu6n А покраска?

What was repaired there? Anyway, I love paited electric terminals ❤

@Kogacarlo

5 ай бұрын

Lol. Well seen

@raufjaleel8317

2 ай бұрын

He just changed the gasket of the pump section at 3:00

@scott4981

2 ай бұрын

@@raufjaleel8317 that and another charge freon a metal valve stem added to inline?

@HereOnYouTubeCommenting

27 күн бұрын

he just opened it up and cleaned it out, it was clogged.

That Torx Screwdriver!

@mrbyamile6973

7 күн бұрын

I hope the guy welding the compressor back together isn't the same guy who built that torx

Class bit of welding on that screwdriver

great work… we Pakistanis love cleaning things with Gasoline/Petrol 😄.

@Talentfy

7 ай бұрын

Thanks for liking.

@AmsFox-just4fun_SA

6 ай бұрын

We too in South Africa

@davidbwn

5 ай бұрын

The ultimate cleaning agent. Even cleans oil out of concrete.

@bristleconepinus2378

2 ай бұрын

i thought it was Mountain Dew?@@davidbwn

I hope there is an RCD on the test rig. The hardest part of that job is welding the seam without leaks. That weld looked perfect to me. I would have thought MIG would be easier. Minutes to watch but a lot longer to do. What was wrong with it to begin with? Adding the Danfoss label was going above and beyond.

@derrickenbuenosaires

3 ай бұрын

I would assume it was mechanical failure. I'm not sure if they rewind the coils within if it happens to be an electrical failure. Could've been something simple like a gasket leak. Didn't see them change any parts.

@foxythedirtydog4494

3 ай бұрын

​@@derrickenbuenosairesall he did was partly clean it and replace a couple of gaskets. I doubt there was much wrong with it to begin. Maybe just had a faulty start relay or removed from a scrap fridge. Painting the terminals is going to be a nuisance. Probably won't last any longer than just changing the oil would have done. No point doing this in a first world country as the Labour costs would mean it is no cheaper than a new one. I fit larger recon compressors regularly but pointless for something that small.

@benv9711

3 ай бұрын

Get over it

@rfjames5259

3 ай бұрын

Broken connecting rod

@thedavesofourlives1

3 ай бұрын

missing rod can be seen at @0:36 @@rfjames5259

Falta limpiar y calibrar valvulas de baja y alta. Revisar compresion,arranque,retencion de presion o compresion. Perdidas o fugas en los empaques. Revisar fuga en el sellado. Falta mucho para decir que es una reparacion.

@mariberbagiinformasiagusin4467

6 ай бұрын

👍

@yuriperes83

5 ай бұрын

Realmente hablando, la unica cosa bien hecha fue la soldadura.

Glad that they recycle/refurbished the compressor than throw it away, it didnt show the fault of the unit.... Nice welding though...

@scott4981

2 ай бұрын

now it will turnover another astounding 43 billion 👀times as this is a new lifetime😳

Сварщик вообще жёсткий, как будто робот заварил.

@acbdcd1897

6 ай бұрын

Не понял как масло внутрь заливали? И что чинили?

@user-kz5iy2ez1l

6 ай бұрын

Я вот тоже не понял насчёт починки. Вроде все зеркальные детали насоса компрессора остались в том же виде, что и были изначально.

@hepto100

5 ай бұрын

@@acbdcd1897 прокладку сменили, помыли от мусора и соответственно звук работы стал тише - вот и всё

@user-ty5qy3iu6n

Ай бұрын

@@acbdcd1897масло внутрь заливается при помощи вакуумного насоса, чинили прокладку клапанной доски

@user-tf6kz9sd3h

Ай бұрын

Заменили подшипник,не благодари !Рф в перде!

Merci !! du partage beau travail !!

Toll.... Wahre Nachhaltigkeitswunder !

I believe the problem was a worn armature bearing causing the armature to hang or rub as evidenced by the material he's showing in the bottom of the pan before cleaning. i dont think he showed replacement of those bearings - either that or the compressor gasget that he scrapes off near the end was leaking

@danielpurcell7395

5 ай бұрын

There was what appeared to be oil laying in the bottom of the of the container? I think it was a bad gasket? judging by him using cleaning fluid on all of the components?

@_..-.._..-.._

4 ай бұрын

@@danielpurcell7395you think????? Maybe?????? Questions???? Comments???? Answers?????? Question marks????

@mannys9130

3 ай бұрын

​@@danielpurcell7395 There's supposed to be quite a lot of oil inside that container. That piece that he took out and was working on for the majority of the video is the piston and motor unit, and that whole thing sits in a puddle of oil inside the housing. The lower bearing is also an oil pump and it picks up oil and splashes it all over the compressor piston and crankshaft. The refrigerant gas itself inside the compressor also dissolves and carries the oil throughout the compressor so that the piston's chamber and the reed valves are coated in oil at all times too. To actually complete this "repair/refurbishment" process, the compressor housing should have been refilled with a lot of oil, then the compressor housing should have been vacuumed down and filled with dry nitrogen gas, and then those little copper stub tubes should have been crimped or brazed shut so that the nitrogen stays inside keeping dust and moisture out of the unit to prevent rust.

@danielpurcell7395

3 ай бұрын

@@mannys9130thank you for the information. I’ve repaired many things in my life, but never a compressor out of a refrigerator. God Bless.

Didn't look like he fixed anything, just cleaning?

@danial8412

24 күн бұрын

They spray it and put some stickers on it.

Блин! Если бы у менч была такая отвертка , переделаная на звезду 😮. Я бы тоде так смог🎉😂. А головку тоже всегда точильным камнем плоскость правлю. Напильником еще хорошо получается. Ведь чем больше рисок на плоскости - тем лучше трение. 😅

@a.r1832

5 ай бұрын

Серьезная вещь.

@Mr.T-HUX

5 ай бұрын

А контакты тоже красишь?) Я вот возьму на заметку.

@santey240578

Ай бұрын

производители компрессоров суициднулись разом

@dmitrystrelov6183

Күн бұрын

​@@Mr.T-HUXконтакты надо серебрянкой красить😂

В чем была поломка? Прокладку выдуло? Там в начале вообще похоже поршень отсутствовал. Тема не раскрыта….😂

@user-cm1ls6sh4m

Жыл бұрын

Скорее всего, компрессор сам был в порядке внутри, а вот корпус маленько подгнил. Очень похоже, что холодильник изначально "утёк", и его выкинули. Потом кто-то принёс от него компрессор, чтобы его проверили и привели в порядок. Upd: Возможно, сам компрессор и стал причиной утечки или недостаточного напора, поскольку мастер перебрал поршневую часть. Я так это понимаю. Если неправ, готов к поправкам.

@user-iy7fy2yu4s

9 ай бұрын

@@user-cm1ls6sh4m Олег , судя по комменту вы пробовали чинить компрессора ? Я от познания всего тоже решился . Столкнулся с проблемой найти кто изготавливает прокладки , хотя индийцы их ножницами вырезают и мне придется , уж больно неадекватный ценник , 12500 р за 50 шт . Вопрос еще , может у кого получилось сделать станок для срезания головки и держатель для свакрки компрессора ? . Мне думается что ситуация в скором времени в россии будет такая что и ремонтировать компрессора начнут массово , если поставки во время 3й мировой с китая сократятся . А современные компрессора полное говно , и любая работа в конторах будет дороже чем сам новый компрессор . И еще : не найду информацию какой жидкостью промывают они внутренности мотора ? Бензином нельзя , они часто проверяют под током с искрами , значит не бензин и не керосин , что ?

@user-tk4zm6rv4d

7 ай бұрын

похоже мыли соляркой) вопрос , сколько там воды останется после такого мытья?)@@user-iy7fy2yu4s

@user-xp5rq7uw1j

6 ай бұрын

​@@user-iy7fy2yu4sлогичнее это делать тем же маслом,которое заправляется в компрессор(хотя,не факт,что они его заправили им))

@user-iy7fy2yu4s

6 ай бұрын

@@user-xp5rq7uw1j масло дорогое . я смывал все же бензином и высушивал. кто делает прокладки нашел . по 50р шт . пока плотно не подошел к ремонту но выяснил что причина поломки старых не масло и не не обмотка а стирание поршнем гильзы , да так что как пестик в колоколе болтает . в этом случае собирать из двух один где голова рабочая .

А потом на Авито продают: абсолютно новый мотор, не битый, не крашеный

@dmitrystrelov6183

Күн бұрын

Гониво . Разбирающийся увидит второй шов , да и патрубки прям заводские 😂

This shows why some foreign "remanufactured" repair parts don't last very long. Made to run again but not truly repaired.

These kind of guys will inherit the Earth.

Súper 💯💯

Pessoas assim,faz falta aqui no Brasil!

*Разобрал. Помыл. Отремонтировано? Крестовая отвертка нано технология просто!*

@Ramulus2009

6 ай бұрын

Это был Торкс.

@dmitryderek4096

6 ай бұрын

Собрал и покрасил. 😅. Без наклейки не взлетит. Проверил главное рабочую обмотку. А если пусковой кирдык - придется опять разваривать. Но судя по видео - это не проблема. 😅

Spray painting the electrical contacts is less than ideal.

Great job, pretty sure he swapped out the valve plate there, didn't get caught by the camera. Here's hoping those guys are recovering all those nasty cfc's when they're scrapping those fridges 🤞🏼

@PR-cj8pd

4 ай бұрын

Aren't most fridges using butane for decades now?

@_..-.._..-.._

4 ай бұрын

@@PR-cj8pdno

@SuperBicycleRepairMan

4 ай бұрын

Ehh, I think some use propane but a lot more use R134a to reduce running costs. HFC's are bad greenhouse gas though.

So what was fixed???

@dmitrystrelov6183

Күн бұрын

Прокладку клапанной доски .

BUENÍSIMO GRACIAS

Писец, вот так купишь новый холодильник с таким компрессором....

@user-mm7ll4qp7k

7 ай бұрын

Я выбросил Стинол с двумя такими Данфосами! Ремонт обошелся бы дороже...экономика. Новый Бош с одним компрессором из Китая холодит не хуже :)

@alexdiver9809

3 ай бұрын

@@user-mm7ll4qp7k Стинол с двумя Данфосами из Германии пашет уже 20 лет. Пластик местами пожелтел, менял выключатель света, чистил дренажную трубку - вот и все проблемы.

@user-gb6kz6qd3u

5 күн бұрын

@@user-mm7ll4qp7k пока клеевые локринги не разойдутся и не утечет хладагент...

Wouldn’t the weld contaminate the inside? I didn’t see any nitrogen used.

@billybowbob2071

4 ай бұрын

The nitrogen was 78.08% regular atmospheric content 😂. Just 21.92% contamination

Keren, sukses mas bro, salam kenal dari pekalongan

Good work , pls what is the material of valve plate gasket

❤Congratulations for your recycling work. hello from France ❤

Beautiful job! Such skill and pride 🎉

@Talentfy

Ай бұрын

Wow, thank you!

Most ppl in developed countries are "green" and feel as saving the world on their Teslas, but this guy is saving more carbon emissions fixing a fridge that you will in years.

@user-re7cq3wy6r

8 күн бұрын

no

Good job

Thank you for your video 🙏🙏🙏

@Talentfy

4 ай бұрын

My pleasure.

Very impressive!

And everyone has the tools of a metals shop!

Nice welding but he should have changed the bearings.

Ésta muy bien la repotenciacion del compresor, lo malo es que otros la venden como nuevas

@raufjaleel8317

2 ай бұрын

No! They sell these as a repaired compressors.

Are they reselling these repaired compressors as new? What's with the fresh paint job and new labeling? I have no idea how long these rebuilts last, but the appearance fails the sniff test.

Parabens!

What class bit of welding?

بسم الله ماشاء الله هذا إلي أريد الرزق من ربه

Easy Pezy if you have a cutter and a welding jig never mind these units are originally assembled in white rooms I’m sure it will be fine that compressor wholesale is less than 100$

How much oil and what type do they refill with? When?

Very good! 👏👏👏👏

To mi się podoba, naprawiać a nie wyrzucać .

@d..c..

5 ай бұрын

Ciekawe ile to pociągnie. Nawet łożysk nie wymienił.

@sylwester5767

5 ай бұрын

@@d..c.. Tyle pociągnie żeby potem znowu naprawiać, ale na pewno koszt naprawy jest mniejszy niż zakup nowej sprężarki.

@d..c..

5 ай бұрын

@@sylwester5767 Ale kto ma czas i ochotę co 2 lata sprężarkę naprawiać?

@sylwester5767

5 ай бұрын

@@d..c.. No u nas to na pewno nikt ale w tamtych krajach widać mają😄

@d..c..

5 ай бұрын

@@sylwester5767 Chodzi mi o klientów tych usług...

Awesome

After repairing I was told to connect the 3 wires from 3 phase 380v to the 3 terminals of the compressor

1:45 is he spraying the coil with oil to wash it? so curious. I work in hvac but only replace compressors.

@meditation9112

7 ай бұрын

nah that's diesel

@FC-qe1wl

5 ай бұрын

@retroguardian4802 probably carbon techachorlide ......the stuff we banned many years ago

@leesmith1558

5 ай бұрын

I think Petrol@@meditation9112

Excellent travail les gars !

The same outfit that supplied Boeing with their door bolts

@phyrros1

12 күн бұрын

😂😂😂

Someone buy the man a torx driver

The torx screwdriver killed me

Top.10.

Yeah, but the bearings weren't even changed.

Con que producto lo limpian?

In America it would be stripped for copper. These people are productive and saving them from destruction and trash land fills. I just wish they would have explained it in the video of what they do and use so I could do it if mine ever breaks down.

@jamskinner

5 ай бұрын

It’s just not cost effective. Costs more to repair then make a new one.

What oil do you use for cleaning?

@AlQuran-Hidayah

7 ай бұрын

it’s gasoline/petrol.

@andrelimadasilvasilva5709

6 ай бұрын

You can use diesel too!!

what would be the restored part??

I am from indonesia❤

did Zero to fix compressor - shinny black paint fixes all

Сварной крутой!

ਕੰਪਰੇਸ਼ਰ ਦਾ ਸਪਰਿੰਗ ਟੁੱਟ ਗਿਆ ਹੈ ਗੋਦਰੇਜ , ਇਸ ਦਾ ਹੱਲ ਹੋ ਸਕਦਾ ਹੈ

amazing.

@Talentfy

5 ай бұрын

Glad you think so!

No light for Grandma😂😂😂😂

No va bañado en aceite?

What we need back in the USA

Shop location??

Он свое отработал , этот ремонт не на долго

👍👍👍

Please where gloves, the chemicals are bad for you.🙂🙂🙂🙂

I saw a compressor disassembled, then reassembled. I did not see any diagnosis, troubleshooting or even testing of the reassembled unit. Was it repaired? Who knows....

@alexdiver9809

3 ай бұрын

New gasket... 😉

и продали как новый. 😁😁😁

Nice welding…

@sonnyc3826

5 ай бұрын

yeah i thought so too that guy is a good welder a nice clean bead

These guys are crafty

Good

Bahut rough work, but Pakistani are good mender.

И в новый холодильник его потом :)

What was fixed?

What repairs?

There's a big missing time chunk in cleaning at 1:07

Like the welding jig😅😅

Bro wearing a paper mask, but no glasses when he's grinding is wild.

Kırık tornavida,imkansızlıklar ve başarı... Hepsi evde ki çocuklara bir tane ekmek götürebilmek için... Tebrik ederim

@Barmaley80x

6 ай бұрын

Ничего не сломанная. Подваренная бита, удлиненный шток отвертки. Этот просто удобнее для работы. А так половиной бит и не подлезть к отверстиюб

My question is. For how long will that compressor last?

@user-dv9cb7tm8o

6 күн бұрын

Лет 30. Потом ещё раз отремонтируют, и ещё 30.

Very good

Тоже не понял, в чем поломка(

Mountain Dew does the trick every time.

Czyli kupując kompresor Danfos nie mam pewności czy jest po regeneracji czy nowy ? :)

It is not clear what was the problem with the engine, it opened and closed and that's it

Yo no he visto que halla arreglado nada lo que hizo fue desarmar y limpiar y nisiquiera ha verificado presion y amperaje como sabe que aun no sigue malo . Esto no es una reparacion

Which chemicals do you use for cleaning

@raufjaleel8317

2 ай бұрын

It's a closely guarded secret😉

Was that an certified Danfoss workshop ? hmmm i don't think so

I wonder what brand of pop is he using to clean it and how does that fix the compressor?

@westhavenor9513

3 ай бұрын

Mountain Dew for sure

از‌کجا‌وچهطوری‌میشه‌این‌کوپرسورهارو‌خرید‌وسفارش‌داد