Great idea taking a picture of the board before removing wires

@fixitFlip

2 жыл бұрын

Thanks!

I’m having a faulty relay problem in my rv roof ac unit, I just ordered a new relay and I’m going to try and solder the new one on. I figured I’d try fixing it myself for $7 rather than buying a new circuit board for $180. Great video flip!

@fixitFlip

2 жыл бұрын

Absolutely and thanks brother! You can save a lot of money if you can do your own soldering!

Great detail and thanks for the repair center information

@fixitFlip

4 ай бұрын

Thanks and no problem.

Thanks!!

@fixitFlip

2 жыл бұрын

No problem!

Great video and info about circuit board medics!!

@fixitFlip

11 ай бұрын

Thank you! They were a great company to work with!

Have the exact same model, mine is doing basically the same thing yours did, but as of this moment haven't yet pulled it out to test the various likely components. Mine will heat to ~240F before it seems to "top out," so to speak, and doesn't want to heat further, other than a few times when I've opened the door, shut off the bake cycle and restarted it again, then it proceeded up to the set temp (350F) in short order almost like new. Bizarre. That's where I apparently differ from the problem you were having, as at the end of your video you said it wasn't heating up at all. I'm hoping it's the temp sensor that's gradually starting to fail, simple and relatively cheap repair.

@Bluebloods7

Жыл бұрын

Also I've taken the back top panel off mine in the past to remove the overlay for a similar reason you did, too funny. The wife loves to make things on those back burners that throw off a ton of steam without turning the vent hood on, so I suspect that overtime the excess moisture accrued behind the overlay and led to the error codes and buttons being triggered on the display board without being touched (spooky!). We would be sitting in the living room and all of a sudden the oven would start beeping, different cycles being initialized, etc.

@fixitFlip

Жыл бұрын

@@Bluebloods7 That is creepy, lol. And yes, hopefully for you it is the temp sensor. Cheaper fix. Mine would go up to about 200 and then just stop there. Good luck with the project!

You are amazing!

@fixitFlip

2 жыл бұрын

Ha ha, thank you!!

I replaced the control board, igniter and the probe on my Frigidaire convection oven and it still takes forever to heat up and does not go up to set temperature either. Very frustrated… what could be the problem??????

@fixitFlip

Жыл бұрын

Have you tested the bake element? I linked 2 good videos in the description under the video that are great for diagnosing what is wrong.

how much does it cost to repair the control board including a shipping fee?

@fixitFlip

7 ай бұрын

I don't remember the exact price, I just remember it was much cheaper than buying a new one!

You mentioned taking the overlay off to clean the thing for an error code, I suspect I need to do the same right now. F11 error code, did you need to remove the glued on portion under the overlay also to clean, or just clean the part under black overlay?

@fixitFlip

Жыл бұрын

I did. I removed the glued on part when I had the same error code and cleaned with rubbing alcohol and a cue tip where the buttons connect and that did the trick.

What if the display has 5d or Sd

My fridgare stoves all burner works good. But oven not heating up. Should i replace control switch and will solve my problem 🤔

@fixitFlip

Жыл бұрын

The control board is one of a few problems that could be going on. There are a few good videos here on KZread about diagnosing the issue.

My oven (also a Frigidaire Gallery, with convection) does not heat to its setpoint. It stays in the 200's F. Could this be due to one or more of the three elements?

@fixitFlip

Жыл бұрын

Yes, I would say it more than likely is!

@Bluebloods7

Жыл бұрын

Exact same issue I'm having with mine (same oven as Flip's and yours) - it tops out ~240F and doesn't want to heat past that point. Been able to mess with it a little to get it to proceed onto the 350F set temp a few times while this has been going on, but appearing now that it's completely dead as it doesn't want to proceed past ~200F now.

How much did it cost for Circuit Board Medics to repair your circuit board? I have the same stove and same issue.

@fixitFlip

Жыл бұрын

I don't remember the exact price but a lot cheaper than buying a new board.

My control board has no light and the door is locked, it happened after self-cleaning. can you help me with what happened?

What is the part number for the control board

@fixitFlip

Жыл бұрын

5304495520

@j.warren757

Жыл бұрын

@@fixitFlip thank you

@fixitFlip

Жыл бұрын

@@j.warren757 No problem.

My stovepipe and oven is not working. Amana

@fixitFlip

2 жыл бұрын

Did you mean stove top?

How can you remove the 5d from the Frigidaire stove from the panel