Franke Ascona Tap Stiff Neck Repair most mono blocks the same Link to Tools and Parts, www.amazon.co.uk/shop/aaanton11 Link to descaling fluid on Amazon, amzn.to/36WicBy
Жүктеу.....
Пікірлер: 83
@alanpayne14422 жыл бұрын
Good video - a little tip I've learned over the years is while working on sinks and basins is to always fit all sink stoppers/plugs just in case the little grub screws or other small bits fall down the drain. It save a lot of dismantling the waste trap.
@aaanton11
2 жыл бұрын
Thanks for the great information👍🏻👍🏻🛠
@richardward24804 жыл бұрын
Thanks! I have been putting off this job for months, if I'd have known it was this simple...... You've saved me a plumber call out or just replacing the tap due to not knowing the simplicity of solving this problem!
@aaanton11
4 жыл бұрын
Thanks for the great comments👍🏻👍🏻🛠.
@cathkiddle35003 жыл бұрын
Just found this video and finally fixed my stiff Ascona tap properly - I say stiff but the whole tap was turning with it. Had mine a while so no "just popping" it out for me - tried silicon wd40 then had to use a bit of the silicone grease just to help get it out. Cleaned it all up as shown and then regreased with the silicon grease as suggested in the comments. Now it's like I bought it new - amazed it was so straightforward really and just as shown in the video. Thanks very much aaanton11
@aaanton11
3 жыл бұрын
Thanks Cath for the great comments love to hear a good fix story👍🏻👍🏻🛠
@ianer56 жыл бұрын
Thanks Franke, saved me a lot of time and money.
@aaanton11
6 жыл бұрын
+ian atkinson 👍🏻👍🏻
@zaffiqbal97404 жыл бұрын
Many thanks for ur video. It helped me fix my issue. Also the hint about the gap on the white clip was really useful. No more leak. Cheers.
@aaanton11
4 жыл бұрын
Glad it helped! Thanks for the great comments👍🏻👍🏻🛠
@allisond2087 жыл бұрын
EXACTLY what I was looking for - thank you so much
@aaanton11
7 жыл бұрын
+Allison D happy to help👍🏻
@jeffreycrawley80946 жыл бұрын
Thank you! That swan neck had been getting stiffer and stiffer over the last 6 months - fixed in 5 minutes!
@aaanton11
6 жыл бұрын
Great stuff 👍🏻👍🏻
@StevenGalvin.Photography5 жыл бұрын
Thanks for the pointer about placing the gap of the nylon shim at the back :) That's what I'd missed out on when refitting the new o-ring set (1425R) :(
@aaanton11
5 жыл бұрын
Thanks for the great comments 👍🏻👍🏻
@davidbritton15105 жыл бұрын
Thank you for posting, good demo
@aaanton11
5 жыл бұрын
Thanks for watching 👍🏻👍🏻
@paolopandas21034 жыл бұрын
Two minutes to watch your video and ten minutes to fix my kitchen tap that has the same problem. Thanks!
@aaanton11
4 жыл бұрын
Thanks for the great comments👍🏻👍🏻🛠
@grahmanjonas55934 жыл бұрын
Thanks I thought the whole tap would need removing your vid saved me hours.
@aaanton11
4 жыл бұрын
Thanks for the great comments 👍🏻👍🏻🛠
@ismay62587 жыл бұрын
Great vid dude 😀lovely camera angles
@aaanton11
4 жыл бұрын
Thanks for the great comments👍🏻👍🏻🛠
@callandy1002 жыл бұрын
Cheers 😁 cold water valve leaked so replaced (of course it was not standard !) Thought I'd sort the stiff neck while I was at it - so perfect vid thanks.
@aaanton11
2 жыл бұрын
Glad it helped Thanks for the great comments👍🏻👍🏻🛠
@NolTee23 жыл бұрын
Gonna try this tomorrow its a different brand of tap but should still be the same job. Thanks 👍
@aaanton11
3 жыл бұрын
Yes they are all very similar, Thanks for the great comments👍🏻👍🏻🛠
@beegee29835 жыл бұрын
Thank you for posting that`s my next job.
@aaanton11
4 жыл бұрын
Thanks for the great comments👍🏻👍🏻🛠
@glenleslie80873 жыл бұрын
Thanks for this "How to" video, my girlfriend has OCD and I was able to replace her Franke Olympus spout after watching it, so didn't have to get a plumber in, which would have been a major ordeal for her. Glen & Jennie
@aaanton11
3 жыл бұрын
Thanks Glen for the great comments👍🏻👍🏻🛠
@EvanJoanette Жыл бұрын
Thanks. Did the trick with a similar Howden's / Lamona version.
@aaanton11
Жыл бұрын
Thanks for the great information👍🏻👍🏻🛠
@darrencapaldi99913 жыл бұрын
Good video sorted my problem out
@aaanton11
3 жыл бұрын
Thanks for the great comments👍🏻👍🏻🛠
@IBIZABIKE4 жыл бұрын
Thanks ,Some others say put the plug in as not to loose anything down the waste, also silicone grease as Vaseline ruins the seals ?
@aaanton11
4 жыл бұрын
Thanks for the great information👍🏻👍🏻🛠
@BL-ik1zz2 жыл бұрын
Great vid. I've got a franke tap with mixer handle. The lever is quite stiff and sometimes moves the whole unit. Can you do a video on it please?!
@aaanton11
2 жыл бұрын
This video will help, kzread.info/dash/bejne/eKybtKeyndDLm8o.html Thanks for the great comments👍🏻👍🏻🛠
@roberttaylor7854 жыл бұрын
Any advice on how to remove the aerator (tap flow restrictor) on these types of necks because these are a little different to the other ones that are made to screw out. With these styles its very difficult because of the way its designed?
@aaanton11
4 жыл бұрын
I can't say I have ever taken it out, you can clean with a back flush, by removing the neck as in my other video, Thanks for the great comments👍🏻👍🏻🛠
@kwithnics21344 жыл бұрын
Hi mate. The neck of my mixer is leaking. Had a quick look after watching your video and the problem is that mine doesn't have a grub screw at the back. Another difference with your tap is that mine has a threaded collar at the top of the neck that screws down onto the base. Do you think my spout just pulls out ? Cheers
@aaanton11
4 жыл бұрын
there will be something holding it in, Thanks for the great comments👍🏻👍🏻🛠
@paulfraser3204 жыл бұрын
Put the plug in the sink in case you drop the grub screw and use silicon not Vaseline or you will destroy the rubber bits...
@aaanton11
4 жыл бұрын
Thanks Paul for the great information👍🏻👍🏻🛠
@MrNeon88Ай бұрын
❤ awesome video
@aaanton11
Ай бұрын
Glad you liked it Thanks for the great comments👍🏻👍🏻🛠
@nancynancymeyermeyer8898 Жыл бұрын
Very helpful video! Will the petroleum jelly degrade the gaskets?
@aaanton11
Жыл бұрын
No issues here, Thanks for the great comments👍🏻👍🏻🛠
@991Geoff Жыл бұрын
Thanks for the vaseline tip, solved immediately!!
@aaanton11
Жыл бұрын
Glad it helped! Thanks for the great comments👍🏻👍🏻🛠
@sueogilvy-white5188 Жыл бұрын
I have a Frankie tap thats leaking at the neck, but my tap has no grub screw, any suggestions how to remove the neck?
@aaanton11
Жыл бұрын
It will be a tiny hole round the back, Thanks for the great comments👍🏻👍🏻🛠
@vrublisko4 жыл бұрын
hi, done as demonstrated, however still leaks , what to do next pls, a new one?
@aaanton11
4 жыл бұрын
There is a link in the description for some new cartridges just pop them in, thanks for the great comments 👍🏻👍🏻🛠
@vrublisko
4 жыл бұрын
@@aaanton11 where is the link again?
@alidavoodparsa39772 жыл бұрын
My basin mixer tap is a Franke Olympus tap and recently started leaking from Spout. I have purchased the replacement O ring parts but I am unable to unscrew it and cannot remove the Spout. Also, the tap is dripping So I tried to remove the handle and look into the cartridge if it needs to be replaced. But when I removed its screw the stiffed cold handle and the cover of the cartridge does not move clockwise or anti-clockwise at all. Any idea of how to loosen it and which tool can unscrew it without a scratch or denting it. Regards Ali
@aaanton11
2 жыл бұрын
this is the kit you need amzn.to/3eBxeT0 Thanks for the great comments👍🏻👍🏻🛠
@alidavoodparsa3977
2 жыл бұрын
@@aaanton11 Thanks, but I have purchased the replacement O ring parts but I am unable to unscrew the grub screw and cannot remove the Spout. it won't come off !!
@Peter-lm3ic
2 жыл бұрын
aaanton11: did you solve your problem because I have similar and cannot remove the spout? It must be limescale, I am trying with white vinager but no luck so far.
@chislenko44995 ай бұрын
Do you need to turn the water off at the mains to do this?
@aaanton11
5 ай бұрын
Or isolate the tap if they are fitted, Thanks for the great comments👍🏻👍🏻🛠
@TheSheamus78Ай бұрын
Do i need to turn the mains water off to do this?
@aaanton11
Ай бұрын
Depends if the tap has isolator valves on the pipes, Thanks for the great comments👍🏻👍🏻🛠
@lynnewilson29754 жыл бұрын
Don’t tighten the grub screw too much as you will have difficulty moving the tap at all !
@aaanton11
4 жыл бұрын
Thanks for the great comments👍🏻👍🏻🛠
@mychannel-kb9xo5 жыл бұрын
was it still leaking after?
@aaanton11
5 жыл бұрын
No all sorted 👍🏻👍🏻Thanks for watching 🛠
@mychannel-kb9xo
5 жыл бұрын
@@aaanton11 I replaced mine with genuine seals from franke and it's still leaking
@stevebearsley2308 Жыл бұрын
A good video and useful information thanks, but always use Plumber's Grease for repairs like this and not Vaseline. Cheers
@aaanton11
Жыл бұрын
Thanks for the great information👍🏻👍🏻🛠
@Handleshmandle12 жыл бұрын
I replaced with fresh o rings today, my tap still leaks 😔
@aaanton11
2 жыл бұрын
Try New cartridges links are in the description, Thanks for the great comments👍🏻👍🏻🛠
@wtfMYRONL4 жыл бұрын
Should be silicone grease not vaseline. Don't even know how I've ended up here 😂
@aaanton11
4 жыл бұрын
Thanks for the great comments👍🏻👍🏻🛠
@Skampino5 жыл бұрын
Vaseline? petroleum jelly will rot rubber o rings
@aaanton11
5 жыл бұрын
Thanks for the great information, what would you use? Silicone grease 🤔
@Itchytriggerfinga
5 жыл бұрын
Absolutely Silicone grease. Like mentioned Vaseline will destroy the o-rings and silicone is waterproof.
@TT-it6cr
4 жыл бұрын
@@aaanton11 Yes, silicone grease or sometimes called plumbers grease. Vaseline will destroy the rubbers within 6 to 12 months.
Пікірлер: 83
Good video - a little tip I've learned over the years is while working on sinks and basins is to always fit all sink stoppers/plugs just in case the little grub screws or other small bits fall down the drain. It save a lot of dismantling the waste trap.
@aaanton11
2 жыл бұрын
Thanks for the great information👍🏻👍🏻🛠
Thanks! I have been putting off this job for months, if I'd have known it was this simple...... You've saved me a plumber call out or just replacing the tap due to not knowing the simplicity of solving this problem!
@aaanton11
4 жыл бұрын
Thanks for the great comments👍🏻👍🏻🛠.
Just found this video and finally fixed my stiff Ascona tap properly - I say stiff but the whole tap was turning with it. Had mine a while so no "just popping" it out for me - tried silicon wd40 then had to use a bit of the silicone grease just to help get it out. Cleaned it all up as shown and then regreased with the silicon grease as suggested in the comments. Now it's like I bought it new - amazed it was so straightforward really and just as shown in the video. Thanks very much aaanton11
@aaanton11
3 жыл бұрын
Thanks Cath for the great comments love to hear a good fix story👍🏻👍🏻🛠
Thanks Franke, saved me a lot of time and money.
@aaanton11
6 жыл бұрын
+ian atkinson 👍🏻👍🏻
Many thanks for ur video. It helped me fix my issue. Also the hint about the gap on the white clip was really useful. No more leak. Cheers.
@aaanton11
4 жыл бұрын
Glad it helped! Thanks for the great comments👍🏻👍🏻🛠
EXACTLY what I was looking for - thank you so much
@aaanton11
7 жыл бұрын
+Allison D happy to help👍🏻
Thank you! That swan neck had been getting stiffer and stiffer over the last 6 months - fixed in 5 minutes!
@aaanton11
6 жыл бұрын
Great stuff 👍🏻👍🏻
Thanks for the pointer about placing the gap of the nylon shim at the back :) That's what I'd missed out on when refitting the new o-ring set (1425R) :(
@aaanton11
5 жыл бұрын
Thanks for the great comments 👍🏻👍🏻
Thank you for posting, good demo
@aaanton11
5 жыл бұрын
Thanks for watching 👍🏻👍🏻
Two minutes to watch your video and ten minutes to fix my kitchen tap that has the same problem. Thanks!
@aaanton11
4 жыл бұрын
Thanks for the great comments👍🏻👍🏻🛠
Thanks I thought the whole tap would need removing your vid saved me hours.
@aaanton11
4 жыл бұрын
Thanks for the great comments 👍🏻👍🏻🛠
Great vid dude 😀lovely camera angles
@aaanton11
4 жыл бұрын
Thanks for the great comments👍🏻👍🏻🛠
Cheers 😁 cold water valve leaked so replaced (of course it was not standard !) Thought I'd sort the stiff neck while I was at it - so perfect vid thanks.
@aaanton11
2 жыл бұрын
Glad it helped Thanks for the great comments👍🏻👍🏻🛠
Gonna try this tomorrow its a different brand of tap but should still be the same job. Thanks 👍
@aaanton11
3 жыл бұрын
Yes they are all very similar, Thanks for the great comments👍🏻👍🏻🛠
Thank you for posting that`s my next job.
@aaanton11
4 жыл бұрын
Thanks for the great comments👍🏻👍🏻🛠
Thanks for this "How to" video, my girlfriend has OCD and I was able to replace her Franke Olympus spout after watching it, so didn't have to get a plumber in, which would have been a major ordeal for her. Glen & Jennie
@aaanton11
3 жыл бұрын
Thanks Glen for the great comments👍🏻👍🏻🛠
Thanks. Did the trick with a similar Howden's / Lamona version.
@aaanton11
Жыл бұрын
Thanks for the great information👍🏻👍🏻🛠
Good video sorted my problem out
@aaanton11
3 жыл бұрын
Thanks for the great comments👍🏻👍🏻🛠
Thanks ,Some others say put the plug in as not to loose anything down the waste, also silicone grease as Vaseline ruins the seals ?
@aaanton11
4 жыл бұрын
Thanks for the great information👍🏻👍🏻🛠
Great vid. I've got a franke tap with mixer handle. The lever is quite stiff and sometimes moves the whole unit. Can you do a video on it please?!
@aaanton11
2 жыл бұрын
This video will help, kzread.info/dash/bejne/eKybtKeyndDLm8o.html Thanks for the great comments👍🏻👍🏻🛠
Any advice on how to remove the aerator (tap flow restrictor) on these types of necks because these are a little different to the other ones that are made to screw out. With these styles its very difficult because of the way its designed?
@aaanton11
4 жыл бұрын
I can't say I have ever taken it out, you can clean with a back flush, by removing the neck as in my other video, Thanks for the great comments👍🏻👍🏻🛠
Hi mate. The neck of my mixer is leaking. Had a quick look after watching your video and the problem is that mine doesn't have a grub screw at the back. Another difference with your tap is that mine has a threaded collar at the top of the neck that screws down onto the base. Do you think my spout just pulls out ? Cheers
@aaanton11
4 жыл бұрын
there will be something holding it in, Thanks for the great comments👍🏻👍🏻🛠
Put the plug in the sink in case you drop the grub screw and use silicon not Vaseline or you will destroy the rubber bits...
@aaanton11
4 жыл бұрын
Thanks Paul for the great information👍🏻👍🏻🛠
❤ awesome video
@aaanton11
Ай бұрын
Glad you liked it Thanks for the great comments👍🏻👍🏻🛠
Very helpful video! Will the petroleum jelly degrade the gaskets?
@aaanton11
Жыл бұрын
No issues here, Thanks for the great comments👍🏻👍🏻🛠
Thanks for the vaseline tip, solved immediately!!
@aaanton11
Жыл бұрын
Glad it helped! Thanks for the great comments👍🏻👍🏻🛠
I have a Frankie tap thats leaking at the neck, but my tap has no grub screw, any suggestions how to remove the neck?
@aaanton11
Жыл бұрын
It will be a tiny hole round the back, Thanks for the great comments👍🏻👍🏻🛠
hi, done as demonstrated, however still leaks , what to do next pls, a new one?
@aaanton11
4 жыл бұрын
There is a link in the description for some new cartridges just pop them in, thanks for the great comments 👍🏻👍🏻🛠
@vrublisko
4 жыл бұрын
@@aaanton11 where is the link again?
My basin mixer tap is a Franke Olympus tap and recently started leaking from Spout. I have purchased the replacement O ring parts but I am unable to unscrew it and cannot remove the Spout. Also, the tap is dripping So I tried to remove the handle and look into the cartridge if it needs to be replaced. But when I removed its screw the stiffed cold handle and the cover of the cartridge does not move clockwise or anti-clockwise at all. Any idea of how to loosen it and which tool can unscrew it without a scratch or denting it. Regards Ali
@aaanton11
2 жыл бұрын
this is the kit you need amzn.to/3eBxeT0 Thanks for the great comments👍🏻👍🏻🛠
@alidavoodparsa3977
2 жыл бұрын
@@aaanton11 Thanks, but I have purchased the replacement O ring parts but I am unable to unscrew the grub screw and cannot remove the Spout. it won't come off !!
@Peter-lm3ic
2 жыл бұрын
aaanton11: did you solve your problem because I have similar and cannot remove the spout? It must be limescale, I am trying with white vinager but no luck so far.
Do you need to turn the water off at the mains to do this?
@aaanton11
5 ай бұрын
Or isolate the tap if they are fitted, Thanks for the great comments👍🏻👍🏻🛠
Do i need to turn the mains water off to do this?
@aaanton11
Ай бұрын
Depends if the tap has isolator valves on the pipes, Thanks for the great comments👍🏻👍🏻🛠
Don’t tighten the grub screw too much as you will have difficulty moving the tap at all !
@aaanton11
4 жыл бұрын
Thanks for the great comments👍🏻👍🏻🛠
was it still leaking after?
@aaanton11
5 жыл бұрын
No all sorted 👍🏻👍🏻Thanks for watching 🛠
@mychannel-kb9xo
5 жыл бұрын
@@aaanton11 I replaced mine with genuine seals from franke and it's still leaking
A good video and useful information thanks, but always use Plumber's Grease for repairs like this and not Vaseline. Cheers
@aaanton11
Жыл бұрын
Thanks for the great information👍🏻👍🏻🛠
I replaced with fresh o rings today, my tap still leaks 😔
@aaanton11
2 жыл бұрын
Try New cartridges links are in the description, Thanks for the great comments👍🏻👍🏻🛠
Should be silicone grease not vaseline. Don't even know how I've ended up here 😂
@aaanton11
4 жыл бұрын
Thanks for the great comments👍🏻👍🏻🛠
Vaseline? petroleum jelly will rot rubber o rings
@aaanton11
5 жыл бұрын
Thanks for the great information, what would you use? Silicone grease 🤔
@Itchytriggerfinga
5 жыл бұрын
Absolutely Silicone grease. Like mentioned Vaseline will destroy the o-rings and silicone is waterproof.
@TT-it6cr
4 жыл бұрын
@@aaanton11 Yes, silicone grease or sometimes called plumbers grease. Vaseline will destroy the rubbers within 6 to 12 months.
@stuartpalmer8233
4 жыл бұрын
I use food-grade silicone.
Vaseline ! That will rot the rubber washers
@aaanton11
3 жыл бұрын
Thanks for the great information👍🏻👍🏻🛠