Frameless to Shameless DIY Jeep Cherokee Frame Stiffeners
How to create your own frame stiffeners using 3x3 angle iron. On my XJ.
Check out our website: muddybeards4x4...
Amazon Store: www.amazon.com...
Get 10% off your purchase at Barnes4wd with this link or use “muddybeards” at checkout
www.barnes4wd....
Get your OnX Offroad Free trial and use Coupon code “Muddybeards” for 20% off your subscription. subscribe.onxm...
Get 10% off your Yes Welder purchase and using coupon code “muddybeards”
yeswelder.com/...
Yankum Ropes: yankum.com?afmc=1v
Get 10% off Olight Products, with coupon code “muddybeards4x4” www.olightstor...
Get 12% off the Setpower AJ30/40/50 With the coupon code: “MuddyBeards4X4”
www.setpowerus...
Tools I Use, MotivXTools: www.motivxtool...
10% off coupon code: muddy
www.setpowerus...
DISCLAIMER: Due to factors out of the control of Muddy Beards 4X4, we cannot guarantee against improper use or unauthorized modifications of this information. Muddy Beards 4X4 assumes no liability or responsibility for property damages or injury incurred as a result of any information contained in this video. Use this information at your own risk. Muddy Beards 4X4 recommends safe practices when working on vehicles and/or with tools seen in this video. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Muddy Beards 4X4. Be safe! This video and description contains affiliate links, which means that if you click on one of the product links, we receive a small commission. This helps support the channel and allows us to continue to make videos like this. Thank you for the support!
Пікірлер: 38
I live locally to affordable offroad and I am building my xj using g alot of thier parts. I also have a decent shop. Videos likes yours are great for me but bad for my wallet lol. I am currently stiffening my frame from front to back. Also 6.5 long arm! And possibly rear coilovers once I recover from long nights of fourwheeling! Thank you for the channel
Thanks for showing this can be done without buying a kit for $500.
@MuddyBeards4X4
5 жыл бұрын
Thanks. I plan on making my own for the front section too
@jackbower8671
3 жыл бұрын
Same, I should be able to do this myself so why not and save the cash and be more satisfied with what I made.
Thanks for sharing. I picked up same angle long time ago. Lacked to motivation to complete install. May give it a try in the spring. Good job on your install.
@MuddyBeards4X4
5 жыл бұрын
Thanks brother. Been planning on making my own for the front section too, but haven't gotten around to it either.
So, does anyone living in the salt belt do this? Here in the Midwest taking things to bare metal and creating places where snow/water/salt can hide seems completely nightmarish.
@michaelg6890
4 жыл бұрын
Weld-through primer works wonders. Look into it, you'll thank me later.
AWESOME, nice video. U've boosted my confidence. ThankU. Michigan out.
ok the xj is not all one unit. the frame is laid first. the 2 floor pans are welded to the frame. then the body is welded to the floor pans. so not all one unit.
No need for weld through primer ? Good job btw.
@MuddyBeards4X4
6 жыл бұрын
I have never used the stuff before, but some sort of protection underneath would have been a good idea.
Thank you!
What settings did you run on your welder and or setup if you don’t mind me asking looking for a starting point. Thanks
Been thinking about doing this to my zj alot more lately.
@MuddyBeards4X4
5 жыл бұрын
I think if your planning on tying in rock sliders, or cross members or even a cage it's pretty important to strengthen up the unibody.
@gatoroffroadOR
5 жыл бұрын
@@MuddyBeards4X4 im going pretty extreme on the build so to skip this simple step would probably be a downffall
@MuddyBeards4X4
5 жыл бұрын
Well then git r done. I bet they sell kits but I just like making stuff myself. Never really looked at a ZJ frame but I'm sure it's similar.
@edzimdahl1158
2 жыл бұрын
There a company found that has an entire frame stiffening kit, front, mid, and rear, both sides, paid 254 + tax & shipping, fabbed my sliders, and rough country 4inch longarm for zj
@dyingtolive076
Жыл бұрын
@@edzimdahl1158 what the link or website? I'm looking to do the same to my ZJ
I want to do something similar on a smaller unibody car.
@MuddyBeards4X4
6 жыл бұрын
Do it! Pretty straight forward. Maybe use lighter material. I used 3/16 but honestly might be over kill. Most frames are prob not that thick
So hopefully you used some sort of seam sealer. Why not finish the welds and close it up completely? It would only make it more solid and stronger than leaving all the stress on those welds. It also seems like a lot of places that water can penetrate between the frame rail and your stiffener. Leading to an eventual rusting out in those spots.
@MuddyBeards4X4
5 жыл бұрын
I have done a lot of reading on this topic and it seems like there was a consensus on forums like NAXJA that stitch welding on the un was important because the metal is thin and brittle. Large amounts of heat can really affect it structurally. I'm no engineer but I thought it made sense so stitch weld it is. The thing I do regret was not using some weld through primer......
hell yea good stuff
Seems cheaper and less time consuming..to buy the mid kit for 180$..then the front for 80$..plus it’s one piece..less welding on the uni frame..
@MuddyBeards4X4
5 жыл бұрын
Definitely not cheaper but yes certainly less time. But using angle wraps the entire channel making it much stronger than a kit, and was needed for the crossmember I built. Buying kits is certainly easier but it is possible to diy and make it specifically for your builds needs.
You guys are MIG’ing it - I would too if I had the option. All I have is a TIG and stick welder. Normally I’d TIG it, but I’m thinking if I use the stick welder I won’t have to remove all the paint from the undercarriage/weld points. I know stick isn’t generally recommended with thin material, but I think some thin 6013, welded on favoring the angle iron rather than the sheet, would be ok. Any recommendations?
@MuddyBeards4X4
4 жыл бұрын
I honestly dont have much experience with stick. But I know people use this process to weld stiffiners all the time. I think it would be fine if like you said, favor the thicker material
@frankj2458
4 жыл бұрын
Muddy Beards 4X4 thanks man, love the show!
What long arm kit are you running?
@MuddyBeards4X4
5 жыл бұрын
I built it using some barnes enduro joints, a piece of 2x4 steel for cross member, and dom tube for the arms.
Whay good are those stiffeners if they're not welded to the floor?
@MuddyBeards4X4
4 жыл бұрын
Still adds strength to the rails..... also provides mounting for rock sliders, cross members, etc... most companies stiffiners do not attach to the thin sheet metal of the floor boards.
technically the Cherokee XJ is a un vehicle
Need a little better lighting to film
@MuddyBeards4X4
6 жыл бұрын
Yep. Have a lot to learn about making videos...... and probably jeeps too.