3D printed parts for car to FPV conversion: www.printables.com/model/660115-dji-o3-fpv-kit-for-rc-car-freecad ~~~~~~~~~~~~~~~~~~~~~~ 00:00 Start, first location (not stabilized goggles footage) 00:11 switching to "rocksteady" stabilized video 03:35 back to goggles' view 03:57 Second location (air unit footage only)

Truly nice 3D printed stuff for RC cars!🎆

Digital image is great but alas out of my budget. Commendable driving! You really can't see far enough ahead at those speeds and "altitude". Thanks for sharing!

Very nice!

Nice one brother! What remote are you getting for this next? Maybe try an aircraft receiver? And also use lipo for the transmitter. And then boost the signal with a more powerful antenna!

@NUeB_RCFPV

7 ай бұрын

I've already pre-ordered a Radiomaster MT12 (with ELRS) and it should arrive soon as shipping starts today. 🙂 At home i saw that the wheel alignment was weird, no wonder that the steering was so over reactive. But FPV driving really is a lot of fun. 😁

@uncleraymond

7 ай бұрын

Yes, that's one of the hottest radios now. Should be good! I initially had problems with alignment as well but I think it was because I didn't bother with repairing the crooked suspension! So be good to inspect that or maybe just get a receiver with gyro?

@NUeB_RCFPV

7 ай бұрын

@@uncleraymond Suspension looks good to me. First thing I did was to raise the car and level out the shocks; even w/ the additional load of the FPV gear the car was too springy. I'll try the reveiver that comes w/ the MT12 first, I think it has no gyro. I think my new setup and a more precise radio will help a lot.

@uncleraymond

7 ай бұрын

@@NUeB_RCFPV oh I’m sure you’ll figure a way out bro. Or you can consult one of those ultra long range FPV KZread videos, there are some FPV dude with a car that can drive far out, really far out…

@Revelation1177

5 ай бұрын

I had that same car it's hard to keep straight but fast as hell I had the walksnail system hooked up to in with the camera on the inside incase it flipped or run in a puddle

Can you make a video on how you’re powering the O3 unit? I have an RC and I want to get the same set up but haven’t figured out to how to power the camera.

@NUeB_RCFPV

Күн бұрын

Just connect the red & black wires from the air unit to the battery.

Is this footage stabilized? Im thinking about adding fpv to my cars but I think it might be too shaky to be worth it

@NUeB_RCFPV

7 ай бұрын

Yes, the O3 air unit has DJI's "rocksteady" automatic image stabilization (AIS). 00:00 to 00:11 you see the live feed recorded in the goggles without AIS and from 00:11 on how much smoother the footage recorded by the air unit is. At 03:35 there is a transition from stabilized footage back to goggles view. So while riding on bumpy paths, the live stream is quite shaky - but I can cope with that. And this is a small 1/12 car, that jumps at every little pebble… Pretty sure that I will get a bigger car too; but this is a good (cheap) start and easy to transport.

Wow ! Je cherche depuis des semaines pour trouver comment utiliser le air unit o3 car j’ai déjà les lunettes goggle 2 , de quoi j’ai besoin pour avoir le même système que toi ??

@NUeB_RCFPV

5 ай бұрын

Very simple: - Goggles 2 (now with TrueRC directional antennas) - DJI O3 air unit + "Arduino ARM" github.com/ramiss/arduino_DJI_03_RC_ARM - servo parallel to steering fir tilt - a 5V fan some 3d printed parts to mount the stuff www.printables.com/model/660115-dji-o3-fpv-kit-for-rc-car-freecad-updated

How is kilometre range video transmitter and receiver

@NUeB_RCFPV

3 ай бұрын

That's very much dependant on the obstrusions… without any it's multiple km.

You get the 03 air unit out from low power mode?

@NUeB_RCFPV

4 ай бұрын

Yes, with a tiny arduino board. Please see the comments of @junebugpetty7386 & myself on this video: kzread.info/dash/bejne/d2GIssltj6-qnpM.html

@NUeB_RCFPV

4 ай бұрын

p. s.: check also Chadd's device if you don't like to tinker around w/ arduino and stuff yourself: kzread.info/dash/bejne/oaNllNWupZvQgMY.html

@syfrslis9232

3 ай бұрын

You can disable it and the air unit will go full power even without arm cmd

@NUeB_RCFPV

3 ай бұрын

@@syfrslis9232 since when and how?

@syfrslis9232

3 ай бұрын

@@NUeB_RCFPV idk maybe on most recent update. Tried that a couple of days ago. Go to setting, control and disable auto low power mode state

Camera name and link please

@NUeB_RCFPV

2 ай бұрын

Camera is DJI O3. What link are u lookin for?

What js the range you have on this?

@NUeB_RCFPV

6 күн бұрын

Some 230 m in the neighborrhood kzread.info/dash/bejne/d2GIssltj6-qnpM.htmlsi=toCbOpVWsH8dTIN2&t=235 - and even more in the flat field. With the other car I got up to 700 m in the fields.

@webbyhawk5643

6 күн бұрын

@@NUeB_RCFPV how to fpv drones get such good range?

@NUeB_RCFPV

6 күн бұрын

@@webbyhawk5643 DJI O3 (later w/ "FCC hack"), radio improved DIY: kzread.info/dash/bejne/nqJomZamYcvOYNI.html (now I use MT12 ELRS instead of crappy stock remote)

@MikeKirchner-zf7zm

5 күн бұрын

That MT12 transmitter is awesome, I have it too and the range is insane lol, and for the price it can't be beat

You should build a lot of these and sell it! How much does it cost??

@NUeB_RCFPV

Ай бұрын

Depends heavily on which car platform you choose. A car like like this: DIY for about 400 Euros; my big one did cost more that 1000. Plus radio (150), plus FPV goggles (600). Analog FPV is much cheaper, but *I* don't want analog any more; started with that a decade ago.

@josealejandroaristizabalca7430

Ай бұрын

Where can I buy ?

Cloud rc streamer is much cooler than this 👍🏻

@NUeB_RCFPV

2 ай бұрын

Kafka is more entertaining than your comment.