Serwus! Zajebiście nagrane czytelnie pokazane! No muza z entuzjazmem! Brawo!

just to add when swoping make sure the new cluster does not have crash damage data or there will be a airbag warning on and will need to be cleared ........ cheers

@Placekmich

2 жыл бұрын

Correct

Nice video!!

@Placekmich

2 жыл бұрын

Thank you!

Hello! I'll probably buy a Convers+ dashboard, I found it not expensive. The question is, what diagnostic equipment will I be able to synchronize the panel with my climate system? I can edit the odometer readings using my scanner, but the rest.

@Placekmich

2 жыл бұрын

If you´ll find dashboard with smaller meleage than your original dash you can use Fosrcan (free extended version) with this: www.aliexpress.com/item/1642318181.html?spm=a2g0o.order_list.0.0.21efa396rYYxTi (I have USB with FTDI chip version). If you have bigger mileage you have to find somebody who can do it. I did not any synchronisation of climate panel with dashboard - it was just plug and play.

@konstantinsavchenko2622

2 жыл бұрын

@@Placekmich I have several scanners for diagnostics. But when I connect the scanner, it says "Transfer odomer data" and that's it)).

@Placekmich

2 жыл бұрын

And which software are you using? Try forscan from forscan.org. There is an option to activate extended version where you can read and write data in car units.

hello after the replacement did you have to connect the car diagnostics to run it or did you just plug in the connector

@Placekmich

2 жыл бұрын

Hi, just plug in... Diagnostic was used only for KM adjustment and then for special functions.

@bosko1004

2 жыл бұрын

@@Placekmich thank jou

Hola tengo un ford mondeo mk4 y quiero hacer el cambio de cuadro de instrumentos, solo hay que cambiarlo y ya esta? , no hay que hacer nada mas ?

@Placekmich

Жыл бұрын

Correct, just replace dashboard and set km according you original meleage.

@gipsyblog1150

Жыл бұрын

@@Placekmich muchas gracias 👍

Where did you buy the dashboard and how much did it cost? I would also like to change the instrument panel

@Placekmich

2 жыл бұрын

Hi, I bought it from the scrapyard from broken mondeo. Total cost with additional functions activation and language change was approx 200 euros.

Ahoj, mám galaxy 2008 a úplně stejné budíky jako vyndáváš na videu. Protože se mi asi měsíc různě zasekávají ručičky , nebo různě se i přetáčejí, pokusil jsem se v nich dle návodů na youtubu přepájet co šlo. 3 dny to fungovalo a už je všechno zase špatně. Uvažuji, že místo opravy u někoho, raději koupím convers +. Opravdu to stačí jen vyměnit? Dal bys mi nějakou radu? Díky za případné info. Ať se daří.

@Placekmich

2 жыл бұрын

Ahoj, ano opravdu je to jenom o výměně kus za kus. Je potřeba si dát pozor akorát na kilometry - pokud mají nové budíky míň než stávající na autě, jde to nastavit přes rozšířenou licenci Forscan, která je zdarma a levnou diag z číny. Pokud mají najeto víc, už to bude muset udělat někdo, kdo ví co a jak a má potřebné vybavení. Dále je asi potřeba zjišťovat, zda budíky nemají uloženou bouračku v sobě (to já jsem popravdě neřešil, protože mě to nenapadlo, ale někdo to tady zmiňuje v komentářích) - pak bys musel údajně vymazat crash data a to si nejsem jistý jestli jde přes Forscan. Jinak na fcb skupině prodávají budíky už s rozšířenýma funkcema a nahraným cz jazykem včetně nastavených km, ale stojí víc než se dají sehnat na vrakáčích a tak, ale zase je tam určitá záruka že budou fungovat. Tak držím palce ať se zadaří.

Do you need to code the new cluster? I have heard car wont start if you buy new cluster and dont code that because car has immobilize in the cluster??

@Placekmich

Жыл бұрын

You don't need to code immobiliser, data are not stored in the dashboard. You heard probably about wv cars.

Hi. Nice video! how we can adjust mileage? And someting what we need to do for full eorking? Thank you

@Placekmich

Жыл бұрын

Hi, see my other video with Ford Mondeo, there is shown procedure for mileage correction. kzread.info/dash/bejne/loKImJuHkbbLYs4.html

Is the just plug and play? Any modding or programming needed? I have an old smax 2006. I heard many people reporting issues with airbag and seatbelt warning🤔

@Placekmich

3 ай бұрын

Hi, only kilometers are needed to adjust. No other modding is needed. Airbags light warning appears when face-lift dashboard is installed to pre-facelift car.

@Blazestalker100

3 ай бұрын

@@Placekmich how do i know? My car is old, not facelift, but when if tye new dash came off a facelift car? Like i got offered a display from a newer Smax, but i don't know if its a facelift or not. And can i edit mileage i free version forscan? I cant seem to find it 🤔

@Placekmich

3 ай бұрын

PreFace-lift dashboard has silver frame and analog arow for fuel, there more differences, try Google pictures... Extended licence for forscan is free for one month and could be extended.

@PModesto

3 ай бұрын

​@@Placekmich Silver frame and analog arrow for fuel is the Pre-facelift, the facelift don't have arrow for fuel or motor temperature, he have an old 2006 S-Max, so he have a Maxidot cluster.

@Placekmich

3 ай бұрын

Correct, I made a typing error... Now its correct. Yes he could have maxidot, the same as I had on s-max.

Hi, I saw your videos of changing Maxidot odometer to Convers+. I have few questions, I have Ford Mondeo Mk4 2010, 1997 cm³, 103kW, diesel automatic gearbox version. But it has same old odometer like you replaced and It doesn't show real-time car running speed in digital format, which is the only reason I am thinking of upgrading it with Convers+. Can you tell me that after replacing I would be able to see real-time car speed in digital number? 2nd question is regarding Bluetooth, my car doesn't have a Bluetooth for mobile, can I enable Bluetooth by installing Bluetooth module CS7T-14D212-AG ?

@Placekmich

9 ай бұрын

Hi, digital speed is additional function which was activated by local programmer. Original convers dashboard this functionality don't have. Regarding bt module, it depend which radio unit you have. If supports bt streaming or not and it also depends if you have cables prepared for bt module.

I saw your other video doing same thing to an Ford Mondeo MK4, and it was way less steps and easier. Does it needs to dismantle so many panels and screws to change the dashboard on a Ford S-Max?

@Placekmich

Жыл бұрын

Yes, on the s-max it's more difficult due to top steering shaft cover - there are two hidden screws which aren't in the Mondeo.

did you disconnect the battery before you did this job ... cheers

@Placekmich

2 жыл бұрын

Hi, no I did not disconnected the battery, but I would recommend to disconnect it. Just for sure.

dear i have a ford s-max 2.0 tdci 2011 he would buy a watch from the redesign does the number or code have to be the same to work without problems?

@Placekmich

2 жыл бұрын

If you have facelift version of the Ford S-max you have to search for dashboard panel from the facelift version. Pre-facelift and facelift instrumental panel are not compatible without modification of the panel.

@benjaminrados9075

2 жыл бұрын

@@Placekmich that's it thank you so much for helping me

@Placekmich

2 жыл бұрын

You're welcome 😊

@juliusszaszi5899

Жыл бұрын

Ahoj. Co treba urobit ak chcem pouzit budiky po facelifte do pred-faceliftu? Ďakujem

hello, can it be put in a Ford smax 2007 and what frame should be put and if it is plug and play or should something be modified, I await your response, thanks

@Placekmich

2 жыл бұрын

Hi, no physical modifications are needed. Just replace maxidot / halfdot dashboard for the convers. Only mileage has to be adjusted accordit your old dash. And yes it will work also for your s-max 2007.

@kenivag

2 жыл бұрын

@@Placekmich Hello, thanks for answering, but the frames do not have anti-start, so as you say, it is plug play, remove one and put the other in like that.

Hola qué referencia de cuadro has montado en el vídeo, gracias

@Placekmich

Жыл бұрын

I am sorry but I don't understand your question.

Is it possible to do the opposite? Downgrade from Convers+ to the Maxidot?

@Placekmich

Жыл бұрын

There should not be any problem. The procedure is the same. It is just plug and play. Only mileage has to be adjusted according to original value.

Hello! Did the exact same thing but the cluster works but the display is completely black... I mean, when I open the door, it flashes the logo a couple times and then you can barely see the logo, but it's there

@rudri8

Жыл бұрын

Maybe because it has chinese aftermarket radio on it

@Placekmich

Жыл бұрын

Hi, I cannot say what is causing that. Did you tried disconnect the radio unit if it is help? Or try to adjust dashboard light with knob next to light switch.

I'd like to add dark theme and other updates to my Convers+ from 2007 ?

@Placekmich

2 жыл бұрын

Hi, yes this is possible on convers+ from 2007. You have to find your local expert who can do it.

Hello I have a mondeo mk4 2013 and I have changed the cluster to converse + but when I connect it a beeping sound starts

@Placekmich

5 ай бұрын

I would recommend to connect car to the diag to see what is happening.

Hello. I have problems with my dashboard, exactly the same as in your video, with a rectangular screen. But when I bought a panel with the same screen as mine, the climanic system does not work at all. A car with the same system as in this video. Sincerely, Konstantin.

@Placekmich

2 жыл бұрын

Hello Konstantin, is climatic panel working with old dashboard? The new one could be broken and it disable the climatic panel. I would recommend to try another or old dashboard to eliminate or confirm failure in new dashboard.

@konstantinsavchenko2622

2 жыл бұрын

@@Placekmich Yes, I got my dashboard back. However, I soldered the processor and everything got better, for a short time. The climate system works with the old panel, no problem. Have you sold your old dashboard? Maybe I could buy?

@Placekmich

2 жыл бұрын

@@konstantinsavchenko2622 I had the same Idea to solder socket on the board but unfortunately during assembly back I broke the LCD completely (and problem with half working LCD was not repaired anyway). So I have no spare dashboard. I am sorry. Try some local scrapyard to find some convers dashboard. Sometimes you will find really cheap ones as I did. Cheaper than repair of old ones.

@konstantinsavchenko2622

2 жыл бұрын

@@Placekmich I could insert my lcd screen, no problem. If you didn't throw away the old panel, even without a liquid crystal screen, then it's okay, I would buy from you. Sincerely, Konstantin.

@Placekmich

2 жыл бұрын

@@konstantinsavchenko2622 I would prefer to keep them because I have also mondeo MK4 with small display. So I would like to do sopme experiments with this.

Is swapping 1 to 1. Plug and play for de clusters? Cluster working

@Placekmich

Ай бұрын

Yes, it is just swapping of the clusters and adjusting of the mileage.

what is numbers behind the new dashboard I would like to buy same one

@Placekmich

Жыл бұрын

Hi, on my other video with Ford Mondeo it is visible. The Part number is 8M2T-10849-VC. But you can use every dahboard Convers+ and it should work. Only thing you need to keep is pre facelift version for prefacelift car and facelift dashboard for facelift car.

Ahoj, chci se zeptat na S max 2008 mám problémy s budíky už jsem měnil asi 3 a chvili jdou teď rafičky pak zase ne, tak jsem koupil právě dnes ty barevné Convers+ už, ale po zapojení se zase odpojují a připojují furtr dokola, je mozné, ze to bude někde v káblech nebo mám takovou smůlu, že všechny budiky co koupím jsou ko. děkuji

@Placekmich

2 жыл бұрын

Ahoj, upřímně pokud už jsi vyzkoušel několik různých budíků, a chyba se opakuje, hledal bych chybu jinde. Další možností je vyzkoušet koupené budíky u někoho, kdo nemá problém (třeba v Mondeu, kde je k budíků jednodušší přístup).

@maramaryhrasek8485

2 жыл бұрын

@@Placekmich děkuji také si to myslím že to bude jiný problém

@Placekmich

2 жыл бұрын

@@maramaryhrasek8485 ještě chytit někoho z mondeem a jen si ověřit, že nové budíky jsou ok... Víc mě nenapadá...

@maramaryhrasek8485

2 жыл бұрын

@@Placekmich no a právě takového nemám, to bylo první co mě napadlo

@Placekmich

2 жыл бұрын

@@maramaryhrasek8485 škoda, možná se poptat na fcb skupině Ford Mondeo mk4 cz/sk, zda by nebyl někdo ochotný... Občas tam i nabízejí úpravu nebo opravu budíků.

I have a 2006 model and just intalled a converse plus and although everything works ok..i have no lights on the dash panel..climate control radio and all the other buttons..also the same on the steerine will..why??

@Placekmich

Жыл бұрын

I have no clue, in my case everything worked on first trial. I would change old dashboard back to see if the problem remains, just to be sure if the problem is not in the convers...

@gypakos11

Жыл бұрын

Ok thanks

@athyholdt

Жыл бұрын

Unfortunately, the 2006 modell S-Max up to nov-06, I remember correctly, does not support the Converse cluster. The firmware in the GEM module is too old. I don't know if it can be updated, but someone said it couldn't.

I als put in Converse+ . But interior light do not work???

@Placekmich

Ай бұрын

I have no clue why you interior light doesn't work. I never faced to the similar problem.

Ahoj, koukal jsem na výměnu těch budíků. Mám galaxy 2008 a jak tady v komentářích píšeš, tak je to jen o výměně. Jde mi ještě o tu češtinu a rozšířené funkce. Výš o nějaké skupině nebo nějaký odkaz, kde se to dá takto koupit? Nebo to zkusím jinak. Kdyby jsem si na ebay sehnal budíky, dokážeš to za "mírnou" úplatu počeštit a srovnat kilometry, popřípadě i ty rozšířené funkce? Díky Martin

@Placekmich

15 күн бұрын

Ahoj, je to opravdu jen výměna a nastavení km. Češtinu a rozšířené funkce jsem si nechal nahrát od Petra Čadského, ze skupiny Ford Mondeo MK4 CZ/SK na Facebooku.

@martinvrsovsky9337

15 күн бұрын

@@Placekmich a ty km jsi nastavoval jak? To potrebujes nejaky soft? Ten Petr Čadský to dělá na dálku nebo za ním musíš někam dojet? Diky

@Placekmich

15 күн бұрын

Kilometry jsem upravoval přes forscan, je zdarma, ale kilometry jdou upravovat jen směrem nahoru. Funkce mi upravoval přímo v autě, dojel jsem do Slaného. Myslím že funguje kolem Prahy...

Hola me an dicho que después de cambiarla el coche no arrancará eso es cierto ?

@Placekmich

2 жыл бұрын

Hi, no it isn't. In the dashboard there is no immo or similar things. It has nothing to do with keys or starting. For mondeo mk4 or s-max mk1 you can change dashboard without any problems.

Hi, I have car Ford S Max Zetec Tdci 2013 1.6 Diesel u have old Dashboard I need to put LCD Dashboard like your Video can I do that for my card or not

@Placekmich

Жыл бұрын

Hi, if you have facelift version of car, you have to search for facelift version of the dashboard. It will work. You cannot combine pre-facelift dashboard on the facelift car.

Warum die Komplette Verklebung? Sind es nicht nur 2 Schrauben?

@Placekmich

Жыл бұрын

Yes, but access on them you have to uncover upper side of steering wheel cover which is held by another 2 screws. For ford Mondeo it is easier because upper cover is not held by screws.

you didnt get any airbaig error after the swap?

@Placekmich

16 күн бұрын

No error. I think that you will get airbag error message only when you combine face-lift tacho and pre-facelift car.

Is this literally plug & play? With any cluster?

@Placekmich

2 жыл бұрын

Yes, just plug and play. You have to only keep pre & after face-lift version.

@damuavadventures9955

Жыл бұрын

I’ve got a galaxy 2007 I guess it’s exactly the same?

Hi. Working on kuga mk1 ?

@Placekmich

2 жыл бұрын

Hi, I am afraid that this dashboard is not compatible with kuga. But I could be wrong - no experience with kuga.

Same works on focus 1.6 2007?

@Placekmich

Жыл бұрын

I don't have experiences with Focus, so I cannot say.

Ahoj.Bude sa to dat urobit aj na mondeo 2007 2.0 benzin 107 kw? Dakujem

@Placekmich

Жыл бұрын

Ahoj, pokud se jedná o Mondeo MK 4, tak ano. Je musíš hledat benzinovou verzi (má víc otáček na otáčkoměru).

Bonjour j’ai une ford s max 2006 j’ai monté compteur converse + marche mais pas toute les lumières de l’autoradio ne fonctionne pas

@Placekmich

Ай бұрын

Unfortunately I cannot tell. In my case everything worked. Try diagnostic to search for fault codes.

Same works on Mondeo?

@Placekmich

Жыл бұрын

Yes, on mondeo it's same. See my other video with mondeo.

what is the exact number 8M2T-10849????

@Placekmich

Жыл бұрын

Hi, on my other video with Ford Mondeo it is visible. The Part number is 8M2T-10849-VC

@anarnesib25

Жыл бұрын

@@Placekmich Thanks a lot

Para smax 2008 funciona?

@Placekmich

2 жыл бұрын

Yes, but for pre-facelift you need pre-facelift dashboard. Face-lift dashboard and pre-facelift dash is not compatible.

Ola como trocar os quilómetros o meu carro tem mais do o quadrante novo obrigado 🇵🇹

@Placekmich

3 ай бұрын

I adjusted kilometers via Forscan extended licence. But program can adjust km onlu upwards.

@estrelagoldenbaby

3 ай бұрын

Obrigado ❤