Ford N Series Tractor "The coil is bad......or is it?"
A short basic video on how to do a preliminary test of the coil on your tractor.
Жүктеу.....
Пікірлер: 39
@tractorman446110 ай бұрын
On the conversions I've done to Petronix, on tractors or automobiles, I always use their wires as well as their suggested flamethrower coil for the electronic ignition system. Never a failure. Good test procedure on the coil my friend.
@icannevergetthistowork11 ай бұрын
Great video. My tractor just quit on me this morning. Checked everything and then found your video. It was the exact same problem. Thanks for your help!
@TheKiltedHomesteader
11 ай бұрын
That’s awesome! Thank you for watching.
@coltonwillie-wp3wk Жыл бұрын
That was the best example I have found thanks!
@TheKiltedHomesteader
Жыл бұрын
Awesome and thanks for watching!
@dustytrailswithepa11 ай бұрын
Great video my Friend !
@24-Card2 ай бұрын
“The coil never goes bad.” I have replaced MANY, same with the condenser!
@plcreman Жыл бұрын
There is no internal resistor. The resistance of the coil is determined by the length of the wire, the diameter and the composition of the wire. Thinner wire with more turns will read higher than thicker wire. Shorted turns will cause low resistance as well as. A static resistance test is ok, but a better test would be a ring test or better yet an inductance test compared to a known good coil. A small resistor in series is not a bad idea on either coil as of the key is left on and the contacts are closed you have continuous current flowing through the coil and creating heat. Once the points are interrupting the current flow you are getting an AC pulse and this is where inductance and inductive reactance (resistance) comes into play. The higher the RPM the higher frequency of the pulse and the more reactance. Overall the video is a good basic test.
@TheKiltedHomesteader
Жыл бұрын
Thank you for the feedback! All information is greatly appreciated.
@kennethtalbott22336 ай бұрын
those blinking gnomes.....
@captainschannel9331Ай бұрын
😎
@benitocamela8541 Жыл бұрын
My primary show 5 ohms but secondary shows infinite. Does that mean the coil is bad?
@Electric-Bob
Жыл бұрын
Yes
@user-tb5rt4rt6x5 ай бұрын
How do I know if my coil has the internal resistor or not?
@TheKiltedHomesteader
5 ай бұрын
By getting the makers specs. Usualy a part number can help.
@robertpeacock5515 Жыл бұрын
You need to move the ohmeter resistance to 20k for second test.
@TheKiltedHomesteader
Жыл бұрын
Why is that?
@The13thSword
Жыл бұрын
@@TheKiltedHomesteader Because in general, the secondary circuit on an ignition coil will be in the range of 6000 Ohms to 16,000 ohms, depending on the coil's original specification. The Primary circuit should be tested on the 200 Ohms setting on the meter. Same reason. Coil Primary circuits in general will range between 0.2 to 3 Ohms, again depending on the coil's original specification. Just my experience but electronic ignition modules (Pertronics, GM HEI, etc.) don't play well over time with higher resistance on coil Primary circuits. I've learned from research (and from actual doing) that most electronic ignitions that use a Hall Effect signal generator in the distributor work better & longer if the coil Primary resistance is 1.5 Ohms or less. Ideally (at least as far as HEI modules are concerned, Pertronics is similar, depending on model) 0.2 to 0.8 original specification for Primary resistance is best. If you look at Pertronics own website & check the coil Primary specs on their later-model Flame Thrower 2 & 3, they are in those lower ranges. I found it very interesting that both your Primary & Secondary circuits went "open' at the same time. I've never come across a coil that did that. They most usually develop high Secondary resistance over time or the Secondary just goes "open". That's mostly due to time, heat, & the fact that the Secondary can put out 20,000 to 50,00 volts. That's a lot of stress over time & it will break down eventually.
@TheKiltedHomesteader
Жыл бұрын
@@The13thSword thank you for the information!
@t.h.o.r.
3 ай бұрын
@@TheKiltedHomesteaderbecause the resistance is much higher and needs to be measured on a higher scale.
@rodritz838410 ай бұрын
I don't think the secondary winding is connected to the primary winding. To test the secondary you have to connect from the center terminal to the body of the coil which is grounded by the mount.
@TheKiltedHomesteader
10 ай бұрын
Trust me, this way works!
@ianrobinson9565
Ай бұрын
Lucas coils. The Secondary winding is in series with the Primary. Why? This improves the spark at the plug. The 300 volts induced in the Primary at the contact break being added to the Secondary voltage. This effect is known as auto transformer action. Now, please take note. A standard Lucas wet (oil filled) coil is 2.7 ohms. Work on 3 ohms, but check current. On 12V you are looking for 4 AMPS. This is a standard coil without an external resistance. Remember that Lucas coils are wound for positive ground which is negative spark. Don't try running negative earth. Yes it will work for a while, but you must have a negative earth wound coil.
@ianrobinson9565
Ай бұрын
Also the centre terminal of the coil is grounded by the spark plug. The case is fully insulated from both the primary and the Secondary windings of the coil. If you get a reading through the case then you have a faulty coil. Hope I haven't confused you too much. 😊
@marioncobaretti22809 ай бұрын
I have to find a nomes equipped meter
@TheKiltedHomesteader
9 ай бұрын
Let me know if you find one ; D
@timgroleau16129 ай бұрын
I don't believe there is a resistor in the coil. The resistance reading on the primary should be under 1 ohm, because there is a small amount of coiled wire compared to the secondary. To test the secondary. Move the meter to 20K ohms. The secondary has many more coils of wire and would have much more resistance, it should read 5k to 10k on many coils. General rule.
@TheKiltedHomesteader
9 ай бұрын
Yes, some coils have built in resistors and some do not. They make them both ways and for different applications. Thank you for watching.
@Peter-od7op Жыл бұрын
I have ford 3000 tractor it dies at 1400 rpm any ideas
@TheKiltedHomesteader
Жыл бұрын
I don't know much about that machine.
@Peter-od7op
Жыл бұрын
@@TheKiltedHomesteader ty for reply
@samgibson684
Жыл бұрын
Replace your ballast resistor
@acecraige6419Ай бұрын
KAL BO OOO,---SUPUTTT,!!!!
@patrckgann1438Ай бұрын
Should have named the video the impotent nome!😂
@TheKiltedHomesteader
Ай бұрын
lol
@Electric-Bob Жыл бұрын
Its One Point Ohms... Not Point One Ohms Resistance showing on the Meter, Sir. People... ALWAYS Purchase an AUTO RANGING Digital Meter! Harbor Freight GIVES THEM AWAY!!
@TheKiltedHomesteader
Жыл бұрын
Thanks for the info.
@robertbarnhardt97924 ай бұрын
Why all the bs just what is the value of the coil 2 min video
Пікірлер: 39
On the conversions I've done to Petronix, on tractors or automobiles, I always use their wires as well as their suggested flamethrower coil for the electronic ignition system. Never a failure. Good test procedure on the coil my friend.
Great video. My tractor just quit on me this morning. Checked everything and then found your video. It was the exact same problem. Thanks for your help!
@TheKiltedHomesteader
11 ай бұрын
That’s awesome! Thank you for watching.
That was the best example I have found thanks!
@TheKiltedHomesteader
Жыл бұрын
Awesome and thanks for watching!
Great video my Friend !
“The coil never goes bad.” I have replaced MANY, same with the condenser!
There is no internal resistor. The resistance of the coil is determined by the length of the wire, the diameter and the composition of the wire. Thinner wire with more turns will read higher than thicker wire. Shorted turns will cause low resistance as well as. A static resistance test is ok, but a better test would be a ring test or better yet an inductance test compared to a known good coil. A small resistor in series is not a bad idea on either coil as of the key is left on and the contacts are closed you have continuous current flowing through the coil and creating heat. Once the points are interrupting the current flow you are getting an AC pulse and this is where inductance and inductive reactance (resistance) comes into play. The higher the RPM the higher frequency of the pulse and the more reactance. Overall the video is a good basic test.
@TheKiltedHomesteader
Жыл бұрын
Thank you for the feedback! All information is greatly appreciated.
those blinking gnomes.....
😎
My primary show 5 ohms but secondary shows infinite. Does that mean the coil is bad?
@Electric-Bob
Жыл бұрын
Yes
How do I know if my coil has the internal resistor or not?
@TheKiltedHomesteader
5 ай бұрын
By getting the makers specs. Usualy a part number can help.
You need to move the ohmeter resistance to 20k for second test.
@TheKiltedHomesteader
Жыл бұрын
Why is that?
@The13thSword
Жыл бұрын
@@TheKiltedHomesteader Because in general, the secondary circuit on an ignition coil will be in the range of 6000 Ohms to 16,000 ohms, depending on the coil's original specification. The Primary circuit should be tested on the 200 Ohms setting on the meter. Same reason. Coil Primary circuits in general will range between 0.2 to 3 Ohms, again depending on the coil's original specification. Just my experience but electronic ignition modules (Pertronics, GM HEI, etc.) don't play well over time with higher resistance on coil Primary circuits. I've learned from research (and from actual doing) that most electronic ignitions that use a Hall Effect signal generator in the distributor work better & longer if the coil Primary resistance is 1.5 Ohms or less. Ideally (at least as far as HEI modules are concerned, Pertronics is similar, depending on model) 0.2 to 0.8 original specification for Primary resistance is best. If you look at Pertronics own website & check the coil Primary specs on their later-model Flame Thrower 2 & 3, they are in those lower ranges. I found it very interesting that both your Primary & Secondary circuits went "open' at the same time. I've never come across a coil that did that. They most usually develop high Secondary resistance over time or the Secondary just goes "open". That's mostly due to time, heat, & the fact that the Secondary can put out 20,000 to 50,00 volts. That's a lot of stress over time & it will break down eventually.
@TheKiltedHomesteader
Жыл бұрын
@@The13thSword thank you for the information!
@t.h.o.r.
3 ай бұрын
@@TheKiltedHomesteaderbecause the resistance is much higher and needs to be measured on a higher scale.
I don't think the secondary winding is connected to the primary winding. To test the secondary you have to connect from the center terminal to the body of the coil which is grounded by the mount.
@TheKiltedHomesteader
10 ай бұрын
Trust me, this way works!
@ianrobinson9565
Ай бұрын
Lucas coils. The Secondary winding is in series with the Primary. Why? This improves the spark at the plug. The 300 volts induced in the Primary at the contact break being added to the Secondary voltage. This effect is known as auto transformer action. Now, please take note. A standard Lucas wet (oil filled) coil is 2.7 ohms. Work on 3 ohms, but check current. On 12V you are looking for 4 AMPS. This is a standard coil without an external resistance. Remember that Lucas coils are wound for positive ground which is negative spark. Don't try running negative earth. Yes it will work for a while, but you must have a negative earth wound coil.
@ianrobinson9565
Ай бұрын
Also the centre terminal of the coil is grounded by the spark plug. The case is fully insulated from both the primary and the Secondary windings of the coil. If you get a reading through the case then you have a faulty coil. Hope I haven't confused you too much. 😊
I have to find a nomes equipped meter
@TheKiltedHomesteader
9 ай бұрын
Let me know if you find one ; D
I don't believe there is a resistor in the coil. The resistance reading on the primary should be under 1 ohm, because there is a small amount of coiled wire compared to the secondary. To test the secondary. Move the meter to 20K ohms. The secondary has many more coils of wire and would have much more resistance, it should read 5k to 10k on many coils. General rule.
@TheKiltedHomesteader
9 ай бұрын
Yes, some coils have built in resistors and some do not. They make them both ways and for different applications. Thank you for watching.
I have ford 3000 tractor it dies at 1400 rpm any ideas
@TheKiltedHomesteader
Жыл бұрын
I don't know much about that machine.
@Peter-od7op
Жыл бұрын
@@TheKiltedHomesteader ty for reply
@samgibson684
Жыл бұрын
Replace your ballast resistor
KAL BO OOO,---SUPUTTT,!!!!
Should have named the video the impotent nome!😂
@TheKiltedHomesteader
Ай бұрын
lol
Its One Point Ohms... Not Point One Ohms Resistance showing on the Meter, Sir. People... ALWAYS Purchase an AUTO RANGING Digital Meter! Harbor Freight GIVES THEM AWAY!!
@TheKiltedHomesteader
Жыл бұрын
Thanks for the info.
Why all the bs just what is the value of the coil 2 min video
@TheKiltedHomesteader
4 ай бұрын
Thanks for watching!