Seems like they should just build every truck with that already on there. Thats why you buy a 3/4 or 1-ton truck.

Just finished the install just in time for a shower and to enjoy turkey with the family. Thank you for the very detailed video I referenced it multiple times during the install. I used an engine hoist with ratchet straps to the four tie down cleats in the bed and it worked like a dream.

Outstanding! Thanks for taking the time to showing us. I love how you take time to clean as you work.👍🏻

Great attention to detail wish I could find someone near me with the same work ethic...great video thanks

This was probably one of the best KZread videos I've seen regarding installs. Great job Mat. Especially the way you removed the box and the care you took to ensure the cab was not creased or damaged. Only wish you were working at a Ford dealership in my neck the woods, because, I sure know where I'd be taking my Fords for professional work to be done. Keep up the awesome work!!!

@raincitywrench117

2 жыл бұрын

Appreciate the comment! Techs that take pride in their craft, they're out there.

At last, a true craftsman at work. Outstanding video and an excellent install! 5star

Well, today is the day, I have a 2020 F250 and I'm moments away from my install, along with a 55gal Titan fuel tank (direct replacement) and 7500# air lift bags. I hope all goes well. Thank you for a fantastic, detailed video. It is a huge help.

@raincitywrench117

3 жыл бұрын

If you have the ability to remove box, that will make all three installs easy. Those boxes are light enough to where I think four people can lift it off without tailgate attached. Should be a fun job to do, enjoy!

I really love how this man works! I would want him to install this equipment onto my new truck. It came without the hitch preparation for both: Fifth wheel and goose neck ball

This was the most well captured and well documented video I’ve ever seen concerning installs. Appreciate the quality and the professionalism!

HEY just want to thank you. I installed my prep kit today and your video was very helpful. Thanks

@raincitywrench117

2 жыл бұрын

Very nice! Love to hear it.

Nice video!! Thanks for taking the time to document everything!

Good job man, i love that you followed the manual and then made adjustments, and thanks for torquing, it helps keeping a mind at ease cause its someones safety

@raincitywrench117

2 жыл бұрын

That's definitely a job you want the bolts torqued.

Thanks for the great detailed video and the hole template! My brother and I installed in 4 hours with no issues. Saved myself $750 for the install.

@raincitywrench117

2 жыл бұрын

Awesome! Love saving money. Did you remove the box?

@jamesmorris8226

2 жыл бұрын

@@raincitywrench117 Where are you located? I need one installed in a 2022 f350 dually.

@raincitywrench117

2 жыл бұрын

@@jamesmorris8226 Snohomish WA

Thank you for this. I did mine this past weekend and referred to your video whenever I needed some clarification. This made it easy. Quite frankly if you have the right tools, it's a fairly easy job. Only took us a few hours. I also did air lift 5,000 air bags in the back and that took a lot longer with the compressor, tanks, and all. I have about two days in the whole thing. I saved about $2-3k on labor though so it was a good weekend for sure. I can't wait to hook up my new toy hauler to it 🤠

@raincitywrench117

2 жыл бұрын

Awesome! If money can be saved by doing yourself, I'm all over it.

@johnyoung4772

Жыл бұрын

$2-$3K labor? I have a 2023 F350 and my dealer wants $600 labor to install mine.

@Tuckgcinc

Жыл бұрын

@@johnyoung4772 I don't know what type of systems you're talking about, but I duplicated the factory OEM by removing the bed just like this video and did an custom Air Ride with extras. Some of the other products bolt from the top. A whole different project. I got prices from two different Ford dealers and they were about $1,000 for the gooseneck prep. I'm near a big metropolitan area so prices are high here. The air system that I have in my truck is not one of the simple plug and play ones. I put in a constant duty cycle 200 PSI pump, to be able to pump my high pressure tires, and an auxiliary tank. I did some other custom stuff extra ports for tools. It's ran inside the truck with valves and gauges. I could only find two shops to give me a price on that anywhere near me and they both wanted $2,000 and said maybe more. Quite frankly I don't think they wanted to even do the project. 2-3k all Day. It took me in my buddy a long weekend and a few cases of beer, about 40 man hours.

Man your craftsmanship is great!! Attention to detail 👏 great video and informative.....kudos budd

@raincitywrench117

3 жыл бұрын

Appreciate that! The quality I put into my work is the same as if it were mine.

searched the web for 4 hours until I found your video, great video Thanks man

@raincitywrench117

2 жыл бұрын

Thanks for watching & the reply!

This video was fantastic. The step by step explanation was on point.

Thank You for posting your version of how to install the 5th Wheel Crossmember!

@raincitywrench117

3 жыл бұрын

You are very welcome!

Just finished up. Did it on my buddies lift this video made it easy! Thanks for the detailed video. Took us about 3 hours as well. Came out Tits!!!

@raincitywrench117

Жыл бұрын

Awesome! Glad to hear

straightforward and informative, this guy needs to be sponsored

@raincitywrench117

2 жыл бұрын

I second your comment.🙂

Excellent video, nice clean installation

Great video, thanks for sharing that. It's nice to have guys like you getting to the point not like others that talk and talk and don't get to the point.

@raincitywrench117

2 жыл бұрын

Yea, I hate that too.

If I could be assured a competent technician such as this could be found at my local Ford dealer I wouldn't be apprehensive about having the dealer install this item and perform any other service in general..... Great job !

@raincitywrench117

2 жыл бұрын

I hear ya. That goes for about any industry, some good techs/bad techs, good and bad doctors, contractors, etc. This industry only cares about profits. Flat rate techs are in a rush to "make time" so quality suffers. Worked on a comeback just yesterday at our dealer. Reverse lights would flash when turning on right turn signal plus stepping on brake. It just had some wiring work done to the back. The tech never checked his work. Not double checking your work on something important like lights? Really? That wouldn't make me very happy or confident as a customer.

Very well done. Nice clean work, just the way it should be done.

One of the best videos ever made imo. Very well done sir.

@raincitywrench117

3 жыл бұрын

Wow! Appreciate the kind words. Glad you enjoyed.

The part where you showed the removal of the bed was interesting. My bed had to be removed (because the factory managed not to paint a small spot on the back of the cab) and the body shop decided to remove the bed rather then trying to work around it. As a part of this, they removed the rear bumper. I was not sure why they had to do this until I saw your video!

@raincitywrench117

2 жыл бұрын

Yea, it's a tight fit. The older gen trucks come straight up but they tightened up the tolerance for aesthetic purposes.

one of the best videos yet Great Job!!!

Great job all mechanics should be as thorough as you.

This made me so glad that we had this factory installed! 😆 I highly recommend it. We use the B&W Companion w/ Slider Fifth Wheel Hitch, which has a pin that drops in & locks to the bed mounted Turnover Gooseneck Hitch. Unlike a lot of 5th Wheel hitches, it doesn't require any additional attachment points, so it's easy to remove (in 2 heavy pieces) & have a clear bed. We're towing a 40' 5th Wheel & the whole system works really well. We will definitely be putting it in any future trucks too.

@raincitywrench117

15 күн бұрын

Thanks for the comment! Installed a couple B&W companions, really nice units 👍

Such a great video! Thanks!

Just enjoyed watching...very relaxing great job

Best how to video on KZread! Thank you for doing a great job. Have you ever installed upfitter switches??

@raincitywrench117

3 жыл бұрын

I haven't installed upfitter switches yet. My super duty already has them but don't have anything wired in yet. Glad you enjoyed the video.

Awesome video, thanks.

Bought this gooseneck package today. Also bought all new box bolts and retainer nuts since apparently they are a one-time use only. Hoping the bolts come out smoothly...2017 w/ 48k miles.

@raincitywrench117

2 жыл бұрын

No sweat getting them out unless you live in Alberta and only drive in winter. Ford always wants stretch bolts replaced or anything with threadlock. Don’t use an extension when you torque the box bolts, works way better. I learned the hard way

@coloneljessup5949

2 жыл бұрын

@@raincitywrench117 Good to hear. I'm in MI, so we see our fair share of salt. I have the big boy 1/2" Milwaukee impact like yours, so it should do the trick. Thanks for the video - very informative!

Ive watched this video three times. Local ford dealer doesn’t install these. Nearest one is 1 hr away and they don’t have any fifth wheel Prep packages. Ordered mine online for. Gonna tackle this today!

@raincitywrench117

Жыл бұрын

Good luck!🙂

@mikem8475

Жыл бұрын

Took me about 6 hrs this video was great help thanks man

Great video! Only thing I wasn’t too keen on was not putting a protective finish on the cuts for the pucks. Not sure if you mentioned whether it was aluminum or steel. Haven’t had one of the aluminum beds myself but as someone who works with aluminum frequently, it does corrode particularly when cut through the cladding in high moisture environments. We usually treat with Alodine, Prime, and paint or seal to prevent future corrosion. If steel then obviously rust would be the concern.

@raincitywrench117

Жыл бұрын

These are aluminum beds and not worried too much but good ideas.🙂

Thank you for posting the template and the video!!

@raincitywrench117

3 жыл бұрын

Any time!

Thanks for the great video, this helped a lot.

Outstanding work and very helpful video. Thank you!

@raincitywrench117

Жыл бұрын

You're very welcome!

Thanks for posting this, I was a little apprehensive till I watched your video.

@raincitywrench117

3 жыл бұрын

You can do it! Think that was from Happy Gilmore... lol

Excellent work.

Great video. Thank you

just priced the b&w 5th wheel hitch for my f-350. i can amazon the hitch for a bit over $1000. The place only wants $1500. Well worth the $500 for everything that is involved. I was thinking I might could do this myself until the bed needed to be lifted lol.

@raincitywrench117

3 жыл бұрын

Smart move. Time is money. Those B&W's are even more of a pain but really nice units. I've installed two.

You do good work.

I have a factory 5th wheel installed from the factory. Just watched for entertainment. But hey I learned how to put the trim bezels on. I thought they were just supposed to sit on top. Thanks.

@raincitywrench117

2 жыл бұрын

Cool! Have seen them sitting on top before and thought the tech was real lazy but now that you said this, it's possible a lot of people don't know they go into the groove.

Great video!!!

@raincitywrench117

3 жыл бұрын

Thanks for the visit!

Great video

Always wondered about this, but I still think it's a lot easier to get this on the truck from the factory.

@raincitywrench117

2 жыл бұрын

Most definitely!

I have installed the surface rails in a f150 . You made it look easy . Looks like with out that lift & just a block & tackle it would not be that easy.

@raincitywrench117

2 жыл бұрын

Ford aluminum beds are somewhere around 300 lbs & can easily be lifted off with three people. Have a couple sawhorses nearby and you are good to go.

Steel bit doesn’t work great but it works. Aluminum and wood burrs are pretty close

@raincitywrench117

3 жыл бұрын

I recently bought a non ferrous bit for the next one I do, should work great.

I don’t remember ever watched a video more than two times to learn how to do something by myself. Specially a video as long as this one. I must say that this gentleman is a true professional. I wish he was either in the LA area or in the Rio Grande Valley. I would take my truck to him for everything. I hope someone could tell me if this method also applies to a one ton dually. 2022 Ford F-350. Do all the steps in the video would apply the same to a dually 8’ bed? Please! Some one tell me

@raincitywrench117

Жыл бұрын

Appreciate the comment! Everything is the exact same process.

@rafaelcardenas9231

Жыл бұрын

@@raincitywrench117 Thank you so much for replying.

Awesome tutorial, glad I found it! Almost installed this hitch without the inner brackets Any chance you have extra inner brackets you would be willing to sell? I got this hitch off a f350 I put a steel flat bed on and would like to put this on a new f350.

@raincitywrench117

2 жыл бұрын

I don't but you may call your local dealer and cross your fingers. Many of the new pickups have the inner brackets welded on and if your dealer installs these they may have a spare set laying around.

Great video! Any tips for those without a lift for the bed removal or options to partially lift bed for proper fitment?

@raincitywrench117

Жыл бұрын

These aluminum boxes are real light. With the tailgate off, four people can lift it easily. Remove the bumper, invite three friends over and yard that box off. Make sure you drill all the holes first when the box is still bolted down. When you remove the box bolts you can grab a corner and lift up to see how easily it picks up.

I really appreciate such a detailed video as I have this job coming up as soon as Ford releases the fifth wheel prep packages from factory back order. My only question is how did you remove the bed liner material from the bed bolts?

@raincitywrench117

3 жыл бұрын

They are on back order again? They were on BO last year also. I use the same really sharp narrow width gasket scraper in the video to dig in and work around each bolt head and then it will peel up and off in one piece. You may be able to get away with using a box cutter to cut around bolts and then pry up coating with screwdriver

@bobmathews4021

3 жыл бұрын

Wow, after over a 2 month wait the prep pack finally came in. Box had been through the war zone

@bobmathews4021

3 жыл бұрын

and of course was missing parts. Drivers inner bracket not there ( probably laying in a FedEx facility somewhere) no trim kit for the bed holes and the locating pins are missing. The dealer parts people here where I bought the truck are really struggling to figure out what the part #’s are for the missing pieces. Couldn’t be so lucky as to have the inner brackets already welded to the truck and it looks like the LC3C-5L028-CA may be superseded to a new number. The pass side inner I received has the LC3C-5L028-DB listed on it. I’m betting the locating pins are the same as the ones used for the bed and am hoping you could verify that, if so I’ve figured out the # for that.

@raincitywrench117

3 жыл бұрын

@@bobmathews4021 Don't know but they look identical. The last couple kits had metal locating pins so they have changed over from plastic ones at some point. Worst case is you can eyeball xmember or drop bolts down to get aligned and remove after tightening. I will say that every kit I've installed, the crossmember has ended up slightly off to the passenger side but the plastic rings cover up the gaps. The first kit I received was also completely destroyed and missing wiring, brackets. The customer has waited for weeks to get it installed and was on his way down to pick up his new 5th wheel. He completely flipped out and was screaming from what I heard and said was not leaving dealer until it was installed. FO MO CO had to overnight the parts but of course they sent wrong stuff and customer came unglued. LOL What a hell of a mess! I believe the dealer now stocks multiple kits and the first thing I do is check inventory. Ford has completely dropped the ball on packaging, all that holds box closed is two straps and they weight so much that one end peels wide open when they are done heaving it around.

Awesome video. I did one and need to do another soon. Was told the bolts and in frame nuts could not be reused?

@raincitywrench117

3 жыл бұрын

You bet. They are not stretch bolts and have one torque spec. I like doing these jobs. Haven't done one in a few months but spring & summer are coming. Thanks for watching.

@Rain City Wrench Do you have a part # for the bolt kit? Recently bought one of these hitches off of a wrecked superduty but the guys that had it didnt save the bolts. I know i can just go out and buy some good bolts etc locally but i'd rather just buy the correct bolt kit if it's available seperately. And thank you for a great video!!

@raincitywrench117

2 жыл бұрын

I contacted parts. They show no part# for individual bolt kit but did send picture showing hardware quantity and description. Email me if you like & I can send to you.

Looks like it’s worth getting this from the factory as an option.

@raincitywrench117

3 жыл бұрын

Yea, would be a good idea. I'm kind of curious what that option runs.

@22apoach

3 жыл бұрын

I think it’s like a 500 upgrade. 3-4 hours of a mechanics time plus the parts. I’m guessing is more to have it done after assembly

I just want to say thank you for taking the time to make this video. With that being said. I dont have the equipment or the skill set to accomplish this....lol My question how much to i stall?????

@raincitywrench117

Жыл бұрын

Not sure what the kits go for these days, maybe around $700? Dealer labor rates will vary but my guess is this job is somewhere between $1500-$2000

@kevinmcdonald8030

Жыл бұрын

You were close, part 792 labor 1035....

Great video. I may have to do mine when my truck arrives because the factory is saying the prep option is delaying deliveries too much. Sad thing is this $500 option costs $595 just for the parts and I've been quoted $600 for the install. Anyway, just curious if removing the tailgate was required or a convenience?

@raincitywrench117

2 жыл бұрын

Just built a new super duty last week with the prep package. Will be ordering one soon but I'm in no hurry. How long is your wait? I did one and left the tailgate on but it makes the box =back heavy- It's just easier getting it out of the way. The box is surprisingly light and seems like the tailgate is 20% of the weight.

Dude, we need to talk! Holler

Thank you for the great instructional video. Do you know if the 7 way and spacer is available through Ford by themselves?

@raincitywrench117

Жыл бұрын

Depending on your year this may be what you need. HC3Z15A416A accessories.ford.com/products/super-duty-2017-2021-7-pin-trailer-wiring-harness-1

Excellent video! My kit seemed to have come with an extra part. It's about a 18" hydraulic cylinder....any ideas??

@raincitywrench117

3 жыл бұрын

Strange. No idea what it would be for. Wonder if it accidentally fell in at the processing plant?

Great video. I just had this installed on my 22 super duty by a Ford dealership near me. When I got home I noticed the castings seem to be slightly off-center in the bed. I measured the position of the gooseball casting from the left and right side of the bed and there is about a 1/4-inch difference when measuring left-to-center compared to right-to-center. My bed seems to be aligned with the cab based on my measurements but the crossmember seems to be slightly crooked. I’m curious if this can be corrected or even matters? I brought it up with the dealership but haven’t received much of a response as of yet.

@raincitywrench117

13 күн бұрын

Almost every one I have done is slightly off to the passenger side and forward on the right side. There are alignment pins that the bracket fits over but it places it off slightly. Luckily it won't affect anything other than the aesthetics to the eye. You will be good to go 👍

@Ryan727vg

11 күн бұрын

@@raincitywrench117 thanks very much for the reply! Much appreciated

I have a 2015 f350 drw with a spray in bed liner similar to this. Are the bed dimple like this truck where the holes need to be to install the puck system like this?

@raincitywrench117

2 жыл бұрын

The steel boxes have the same dimples. I start with the center & fronts and then measure back 13" (I think) to find the rears.

What locks the goose neck ball into assembly? On my B&W goose neck set up I have a lever that in the wheel well that I pull and push locking the ball in place.

@raincitywrench117

2 жыл бұрын

The factory ball has a lever on top that flips down pressing out two pins that lock it in. I have install two B&W hitches, Those are nice too as they allow you to stow ball upside down when not in use.

Great video thx! My 2022 super duty has a Tremor package. Is everything the same?

@raincitywrench117

11 ай бұрын

Everything is identical 🙂

My 19 i just bought used has the prep kit installed but i do not have the ball, is there a specific one that needs to be used?

@raincitywrench117

3 жыл бұрын

Just needs to fit Ford factory prep packages. Etrailer has a few manufactures:www.etrailer.com/g-2019_Ford_F-350+Super+Duty.htm?style=8+Foot+Bed+with+OEM+Prep+Pkg Ford also makes a nice unit that has tie downs and a storage bag.

nice work probably can do it myself, but I do not have the lift to get the bed up or the building to do it in,so that being said ,how much do you charge and where are you located?

Do you apply any protective coating to the now exposed metal where the drill & hole saw removed metal in order to prevent corrosion at those areas?

@raincitywrench117

3 жыл бұрын

I do not but it definitely wouldn't hurt. Since it's an aluminum box I don't bother, a little oxidation around the lip is all I see happening IMO.

@manunava1776

3 жыл бұрын

@@raincitywrench117 Doh, my bad! I had totally forgotten Ford switched the SD to aluminum as well!

Wow! Nice, precise job you do! Can you install one on my 2019 F450?

@raincitywrench117

3 жыл бұрын

Sure can. I'm 35 miles north of Seattle Wa. If you are in the area we can set it up.

@anthonyleeser4571

3 жыл бұрын

Cool. I'm in Salem, Oregon. My email is aleeser@reagan.com and we can work something out.

Nice video where can I get some of those protector caps

@raincitywrench117

3 жыл бұрын

Find another pickup out in the home depot parking lot and borrow theirs. Nah, better not. Here is a kit on ebay:www.ebay.com/itm/254236619386?chn=ps&norover=1&mkevt=1&mkrid=711-117182-37290-0&mkcid=2&itemid=254236619386&targetid=1068323858110&device=c&mktype=pla&googleloc=9033382&poi=&campaignid=12589942946&mkgroupid=121185185993&rlsatarget=pla-1068323858110&abcId=9300523&merchantid=8260744&gclid=Cj0KCQjwyN-DBhCDARIsAFOELTnyy17r6AFRB2QUNOyv1wMJF890Zy4UQHl_uew_rqzlMfy3T6PKFpMaAkcHEALw_wcB

Great video on the install Is there another kit to install if you are going to use chains? I have heard that some states require using them.

@raincitywrench117

11 ай бұрын

There are safety chain attachments that fit into the outer pucks when using the gooseneck. www.amazon.com/Reese-30134-Attachment-Under-Bed-Gooseneck/dp/B004R35WAO/ref=asc_df_B004R35WAO/?tag=hyprod-20&linkCode=df0&hvadid=242007613379&hvpos=&hvnetw=g&hvrand=9899688782086202783&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9033391&hvtargid=pla-570375513968&psc=1

@swabbievet

11 ай бұрын

Thanks for the info.

Are the receptacles for the 5th wheel posts, also where you install the safety chain anchors for a gooseneck set up?

@raincitywrench117

Жыл бұрын

They make a gooseneck kit with anchors that lock into the outer pucks. Works slick. Not sure what you are asking on the receptacles?

Installed mine today and everything went just as you described. I did notice though that the pucks on one side wound up being half of an inch further forward than the other side. So apparently it is slightly crooked. They still came up through the holes in the bed fine. Do you think this is an issue? I didn’t realize when we put the crossmember on the alignment pegs that there was that much play in it.

@raincitywrench117

2 жыл бұрын

Nope, won't matter at all. The passenger side pucks end up slightly forward on every one I have done. Once the plastic caps are on you don't really notice. I guess that's why the holes are drilled quite a bit larger to allow for misalignment. The structural rigidity will remain unchanged. I may run a tape measure from the cab back to the front pucks on the next one to see if there is any wiggle room front to back.

First class mechanic work. But this is making me lean toward the B&W hitch, I'm sure the ford is stronger, but I don't think I will be towing more than 12-14K with the gooseneck. What do you think of the B&W kit as far as strength. I'm just not wanting to take the bed off my 2023 F350 without a lift. B&W does not require bed removal.. I"m sure you have done both.

@raincitywrench117

11 ай бұрын

Installed a couple B&W units. They fit nice and work great. Real pain to install though. kzread.info/dash/bejne/gaiLrbaSc7uqY84.html&ab_channel=RainCityWrench

@goneridingparts

11 ай бұрын

@@raincitywrench117 video link not working.

Hi I'm in Marysville what would you charge to install the puck system on my 2016 f350 diesel dually? Including the kit? Great video thank you

@raincitywrench117

2 жыл бұрын

I'm not 100% sure but know our dealer charges 5.5hr and think out labor rate is $189hr. My guess is the kit is around 750 bucks so that would put the total install somewhere around $1800 before tax.

How do you know which ones will have the bracket and which one won't? I mean welding onto a frame is not a good idea is it? Integrity of the metal would change from the heat no?

@raincitywrench117

3 жыл бұрын

That I don't know. Seems like every other one I do has the inner brackets already welded on from factory. These are all factory welds, I think the frames are welded in many other areas also so it must not affect anything. The kit has the inner bolt on brackets for those vehicles which are missing them.

Have you done this on any of the 2023s yet? Any significant changes? Just got my prep package finally for mine. Contemplating installing myself.

@raincitywrench117

7 ай бұрын

I haven't yet. Was supposed to do one last Monday on a 23 but it didn't show up. There are quite a few changes on the 23 from the 22 like front control arms, body style/badging, instrument cluster, electronic parking brake, etc but doubt the box/frame are any different.

What length bed for that truck, and thanks for the video. Some of us though will need to use a couple of fall hoists to lift the bed out of the way 😃

@raincitywrench117

2 жыл бұрын

I think that was an 8' bed. The install instructions say to lift bed on each side & block up with 4x4's. It is easier for me to just lift the box off but this is a job you can easily do in your driveway without any lifts. The box is surprisingly light being aluminum. I will say though, it's a real pain to torque the bracket bolts without completely taking the bed off.

@dennismills4862

2 жыл бұрын

@@raincitywrench117 thanks for replying so soon. All the best to you and yours.

My 2021 F250 does not have the welded inner brackets. So, how do you set the height? I don’t see any reference to the proper height in the instructions. Thank you for any help you can provide!

@raincitywrench117

2 жыл бұрын

The fifth wheel bracket will set the height. When installing the side brackets, leave them ever so slightly loose. Lay the crossmember on the frame aligning the two dowel pins then install and tighten the top bolts which will suck the side brackets up tight to the fifth wheel crossmember & will set the height. Lastly tighten the four main side bracket bolts. Bing bang boom you are done! Well once the box is back on.

I just picked up a '17 350 with the prep already installed, the trim rings and covers are missing. Do you happen to know if they sell the trim kit separately? If they do do you have source or part number for teh trim kit?

@raincitywrench117

2 жыл бұрын

You're in luck, yes they do. BC3Z-99000A25-A www.fordgenuineautoparts.com/oem-parts/ford-hardware-kit-bc3z99000a25a?origin=pla&gclid=CjwKCAjwquWVBhBrEiwAt1Kmwkogj0KiksQp1q1W9EwbRUNdG9diwP8G64wxGwTNdxOWis75F0yxTRoCkDAQAvD_BwE

How much does that weigh compared to the Curt and Draw Tite bolt on?

@raincitywrench117

Жыл бұрын

Sorry, I don't know

In my search for a 5th wheel receiver, I'm noticing that they are made specific for certain trucks. My question then is if you use top mounted bed rails that are universal, then isn't it a moot point?

@raincitywrench117

Жыл бұрын

Yes, exactly

Will this same kit fit on a 2013 250?….i like the four pucks to use for a 5tth wheel and the gooseneck option as well

@raincitywrench117

2 жыл бұрын

BC3Z-5F057-A is the kit for 11-16 Superduty's. It looks almost identical and goes in the same way.

If you were to take a factory one out that’s already been installed would you have to take the bed back off or can you do it without taking the bed off?

@raincitywrench117

Жыл бұрын

You don't have to take the bed completely off but will need to remove the box bolts, lift it up enough to place 4x4 wood blocks between the frame to access the bolts and remove bracket. The box is fairly light and can easily be lifted by two people to wedge blocks under it.

When you order this option from the factory, does it come installed? I assumed it did. (BTW i have bought a car from Bickford before and I might order an F450 from there this year or next) thanks

@raincitywrench117

11 ай бұрын

If you order that option it comes installed. Check your build sheet to see if it's listed. It used to be around $600. I ordered that option on my 2022 but they stopped installing during the covid years so I had to pull it. Maybe Ford is back to normal now and they are installing at the factory again?

Hub city Ford in Lafayette Louisiana told me they are not equipped to do this job!!! I have to install this with a bad back because Ford has inexperienced techs!!! Go Ford!

@raincitywrench117

2 жыл бұрын

At least you will know it's done right.

@thomasbroussard2316

2 жыл бұрын

@@raincitywrench117All done!! Took me about 4 hrs and that's with a few breaks. I did end up taking the bumper off just for a little extra view for clearance. That's also including assembly and install of a Reese 27k hitch. Going to make good uses with a 2021 F350 Dually and 2022 KZ Venom 4013tk Toy Hauler!!!

@raincitywrench117

2 жыл бұрын

@@thomasbroussard2316 Three slides, 2 baths, residential shower, center island. Damn, that is a nice hauler!!

I'm 4 minutes into the video hopefully you show the part number to the trim kit as my truck did not come with them and well I hate that I have to throw on a sheet of plywood to haul some top soil, sand, or gravel.

@raincitywrench117

3 жыл бұрын

Don't do that, lumber is the price of gold now. Here is the kit: ford.oempartsonline.com/oem-parts/ford-hardware-kit-bc3z99000a25a?origin=pla&gclid=CjwKCAjw7J6EBhBDEiwA5UUM2vdeWctUnE_ADpnVwLL5vyDKzQe-3sulPmJUhqodUML2CEUHjzhN8hoCimUQAvD_BwE

Great video but do you need to remove the tailgate or can you leave it on and just unplug it? Thanks

@raincitywrench117

2 жыл бұрын

You can leave it on and just unplug it. I did that once but it's in the way so I remove the tailgate every time now.

@lancebarger2470

2 жыл бұрын

@@raincitywrench117 thank you

Do you have a video that shows the puck system being installed on a 2000 f350? I'm haven't been able to find one that says it fits.

@raincitywrench117

2 жыл бұрын

I do not. I think the factory puck setup is for 2010 and up. ETRAILER has below bed rail fifth wheel hitch setups for that year.

Great job. Where are you located?

@raincitywrench117

2 жыл бұрын

Thank you! Snohomish WA

I wonder if this prep package would fit on a 19 F150 since the frame is basically the same.

@raincitywrench117

2 жыл бұрын

Interesting... Have no clue. The cabs are essentially the same but pretty sure the frames are different and they don't have the holes in the frame to attach the side brackets.

Just a quick question for you since you appear to be a tech for a Ford dealership - considering buying a F-350 XLT with the panoramic sunroof. Is the sunroof pretty reliable or should I leave that out of my options list? THANKS!

@raincitywrench117

3 жыл бұрын

Funny you ask, lol. Have seen nothing but problems with them. Yet to see one issue with the old school single glass moonroofs like on my super duty. Vista roofs have one tsb that I know of. The side brackets have plastic laminate over metal & they break apart and bind in the channels. Sound like hell and sometimes the glass completely stops. Fixed about 8 of them so far in the last 14 months and we're talking about rigs with low miles. Also repaired a couple shades, one ripped loose and spooled back up (5.5hr repair) & another had stains from water leaking. The thing I notice on almost every one I have opened is a clunk immediately when the front glass drops down just before it slides back. It's like the front and rear glass want to stick together at the center seals. Have had to apply sil-glyde multiple times for that complaint. They are really cool and I'm sure there are many happy campers but.... If you want a fifth wheel prep package then order with that option and you'll save about a grand.

@mark02tj41

3 жыл бұрын

@@raincitywrench117 THANKS for the info. No sunroof saves $1400. Might also make the difference for me on whether to go with an XLT or just get an XL. Biggest issue now is the seats - will the XL split bench be comfortable enough for my wife's bad back on a long trip; or do I need to go with bucket seats?

@raincitywrench117

3 жыл бұрын

@@mark02tj41 I would recommend buckets

@mark02tj41

3 жыл бұрын

@@raincitywrench117 THANKS! I appreciate the advice!!

@acdii

2 жыл бұрын

I call them Rattle glass roofs because that is what they do. Had two of them, BOTH rattled. They are also COLD in the winter and HOT in the summer. Not having one saves $1500 and about 60 pounds of payload.

I need to remove the bed on my 2012 to fix some holes from red oxide rot. It's the 17+ that are tight, correct? I have a 22 on order and am thinking I may add this down to road, but for now just install the bed rail system since that is what my 5th wheel already uses, but watching the process, not that hard provided a means to lift the bed.

@raincitywrench117

2 жыл бұрын

Yea. The steel boxes lift straight up without interference. I have a 22 on order too since last November. Got a call a few weeks ago saying the fifth wheel prep package would add another 8 weeks so I told them to take that option off. Disappointing since it is only a $550 option. Now I have to send probably 800 or more for the kit and the time to install later down the road.

@acdii

2 жыл бұрын

@@raincitywrench117 I had it removed after looking up what the legs cost for the A20. The bed rail kit for $250 is a far less expensive option and doesn't require bed removal. Get a rubber mat, cut slots in it and you once again have a flat surface to slide things on and lay flat. The only item I really need is the box 7 pin and the TPMS/Camera socket. Does the factory installed Prep have the backing plate that accepts the 7/21 socket in the TPMS kit, or is it the same square box that you installed in this video?

@raincitywrench117

2 жыл бұрын

@@acdii It does not come with it. You will have to do your homework but think you need the 7/12-pin trailer connector and wiring kit LC3T-14G621-AC. This is for pro trailer backup assist, camera and tpms setup.

Is that bed aluminum? Shiny shavings and looked like it drill very easy.....

@raincitywrench117

2 жыл бұрын

Yea, 2017 and up superduty's are aluminum bodies. Makes it much easier to drill.

Is there any dimension difference between a 2019 f350 dually and a 2021 f450 dually bed wise, I have a 1/4” steel tool tray to protect bed from oilfield tools rolling around. I want to upgrade to a f450 just not sure if my tool tray will bolt in the f450, cab to axle distance and bed mounting bolts?

@raincitywrench117

3 жыл бұрын

I'm not sure. Have had a few 450's in the shop and the cab, box and frame look identical. I think the difference is in the front/rear suspension, differentials and wheels. To be sure, stop by your local dealer with a tape measure. Wow, 1/4" tray. Now that will have some weight. Great idea.

@BenDover-gz6bg

3 жыл бұрын

@@raincitywrench117 well unfortunately I can’t find any f450 within 400 miles of me. Thanks for your quick response

@raincitywrench117

3 жыл бұрын

@@BenDover-gz6bg Just looked up specs on Fords website. www.ford.com/trucks/super-duty/models/f450-limited/ Only one 8' box listed for F250-450's. I don't think they have changed box design since they introduced the aluminum bodies so that being said I think the boxes are identical between a 19 F350 and 21 F450. Cheers!

Great tutorial. I got a used kit that does not have the inner brackets because the truck it came off of had them welded on. i see that you did not need your inner brackets. would you be willing to sell them to me?👏

@raincitywrench117

Жыл бұрын

Sure. Send me an email to raincitywrench@gmail.com and we'll figure a way to get them to you.

But did you rustproof the drillen holes? Otherwise just a great video for something we in Europe can only dream about!

@raincitywrench117

2 жыл бұрын

Thanks man! I don't treat the holes. These are aluminum boxes but it wouldn't hurt to install some corrosion inhibiter.

Can this be done by loosening the box and lifting and blocking up the passenger side, then sliding the unit in from that side without removing the box?

@raincitywrench117

3 жыл бұрын

Yes sir. Ford says in the directions to place 4x4 blocks between bed and frame to gain clearance. Removing box makes it much easier but I did my first one by blocking it up. I wouldn’t be surprised if four guys could lift the box off. They are real light compared to steel.

Any chance I could get the part numbers for the bolt kit, trim kit and trailer wiring kit, allignment pin? I can't find a new hitch kit, but I found a new take off that doesn't have them parts. Thanks

@raincitywrench117

2 жыл бұрын

Someone else emailed me wanting the bolt kit PN so I contacted our parts department. They said parts are not sold separately. It only list one part number for the kit with a breakdown on description of parts. Will look and see if I still have that screenshot.

@littledave601

2 жыл бұрын

@@raincitywrench117 I found a write up article you did online. Reese makes the hitches, they just use regular bolts, thats probably what I'll do. Thanks for getting back to me.