These are the Tools and Parts I Recommend: Updated Molded Lead Frame- amzn.to/3myMVgw Bulkhead Sleeve- amzn.to/35NNZqP Pump Pass Through Seal- amzn.to/2FOP9Yc Assembly Lube- amzn.to/35QrstB Transmission Filter- amzn.to/35Lawor Transmission Fluid (may need up to 10qts) amzn.to/3cbkVLg Transmission Pan Gasket (if damaged) amzn.to/33yYuf6 Torque Specs: Molded Lead Frame to Valve Body Bolts- 53 inch lbs Valve Body to Case Bolts- 71 inch lbs Transmission Pan Bolts- 98 inch lbs Valve Body Torque Sequence- drive.google.com/file/d/14Tkq7t-qol_uCCDDZlIOkbJSy9MTKhUD/view?usp=sharing Transfer Tube Seal Locations (if they fell out) drive.google.com/file/d/1HW7e6bVVsdHKjHUy2AReCGMNzyIwV8RV/view?usp=sharing Transmission Fluid Fill and Adjustment- kzread.info/dash/bejne/iIZ4tbN8m8-peKw.html Forscan is free Ford Specific Diagnostic Software: Download Here- forscan.org/home.html ELM 327 Adapter I Recommend- amzn.to/2GC6dBj As an Amazon Associate I earn from qualifying purchases.

@bliskin8847

3 жыл бұрын

FordTechMakuloco just wanted to thank you again for all your great videos, and getting back to me last year. With your help and that of your videos, I fixed my dad's 2000- F150's transmission and changed the timing chain. Had a bit of a Snafu at first when I used the long screw for the right chain guide on both guides, when I put the cover back on I noticed the bolt wasn't flush on the left, so pulled the cover off and found that I had forgotten to pull the pin on one of the tensioners. Anyhow, one year later my dad's truck has nearly the same power as when it was new, and is running great. My next project will be to service the rear differential. Again thanks for all the videos and take care.

@labf5213

3 жыл бұрын

FordTechMakuloco Have you done a swap from 4r75w to 6r80 on a f150 04 5.4 triton?

@josearellano3268

3 жыл бұрын

How can I get a hold of you..?? What’s your number, I have a few questions, lol 😂 I’m think of swapping my 4.6 2v for a 5.4 2v, Can I use the same comp. and engine harness from the 4.6 to run the 5.4..?? It’s on a 2004 f150 not heritage model.. will the transmission bolt on to the 5.4 ..??

@whpony96

3 жыл бұрын

@@josearellano3268 You can get more reliability and a lot more HP \TQ from a Coyote Swap. The 4.6L is pretty Bullitt proof the 5.4L isn't.

@boobizzy4173

3 жыл бұрын

Hey Brian, do you have a video on a 2004 Ford Expedition front heater core removal? 🙏 thanks.

I’ve watched hundreds of automotive DIY videos and appreciate all of them. Overall this is probably the highest quality I’ve seen. Great lighting, great audio, he hits on all the important things, doesn’t repeat himself, nothing irritating. This video should be the model.

Honestly a large majority of ford dealerships and their technicians would benefit from this video, you should probably be getting paid by ford to properly train and provide service procedures to their techs!

@Barrera00009

4 ай бұрын

He gets paid by youtube already , he benifits the world not ford techs

@marcuswolf184

Ай бұрын

Ford trains it's techs better than any other manufacturer. Fact

@WorldCommander

Ай бұрын

@@marcuswolf184 I don't know where the dealerships are getting their mechanics now then. I've been to three different ones and they couldn't fix the problem on my truck. Didn't used to be this way. Always had good luck with Ford mechanics 20 years ago.

@boostedsaleen6146

Ай бұрын

​@@marcuswolf184 traines 😅

@alsofletcher

Ай бұрын

I’m here watching already lmfao

Just finished this repair. Video was spot on. The fluid level check and adjustment was the worst part. Thank Loco for your help. Long live the channel!!

@enzodunn2577

7 күн бұрын

I'm not sure if this is what I need to do myself or not. But mine will sometimes have a loud bang and a jolt like I'm getting rear ended by a small economy car. It has happened when I'm going up a hill at 30mph. And it happens when I try to gun it and get it to go into passing gear to pass someone. It's a loud audible BANG and I feel the whole truck jolt. Mine never got fixed for the recall until today. It's a 2013 3.5 v6 ecoboost and the dealership sent someone out to my home today to perform the recall. And it didn't change anything. I have 138k on the odometer. Was yours doing this loud bang shift type thing as well?

Great video! I've been wrenching for over 45 years and you are one talented technician and a good teacher! Thank You for the hard work you put in editing these videos AFTER you put in a long day at the shop.....well done!

Thank you for another Ford lesson. I do a bulk of the Ford work at the shop I work at & you are a huge part of my jobs being done right the first time. So many lessons that I otherwise would have fumbled my way through. You are awesome! 👍👍

This man has been a live saver not only with my 5.0 6r80 but also my 3 vavle triton. Thanks for everything you do!

You, by far, have the most comprehensive and thorough, how to, videos on KZread. Well done, Sir

This video helped me resolve and repair my Dad's broken pump pass through seal in his 2009 F150 5.4. More videos than I can count of yours have helped me to save a lot of money on Ford repairs and I am extremely grateful. Thank you for all the time you take to make your videos. God bless!

as a ex 21 year ford dealer tech ( 15 years ago ) its good to know i can always fall back to you to keep up with current ford problems , just wanted say thanks for all the info.

As a 20 year Honda/Acura master tech these videos you put out are great!! The close up explanations of the small details, torque specs and sequences, this info is invaluable. Thanks for the help with my tow rig. Liked Subscribed

Brian, My sincere thanks for putting together all of these videos. It has made essential service to my 2017 F-150 5.0L 4X4 easy and done with confidence. This service is the last one on the list after I replaced spark plugs, front differential fluid, transfer case fluid, rear differential fluid, and new Motorcraft yellow coolant. The truck has never run better and I've actually gained 4+ MPG for highway driving. My transmission started acting up (slamming gears and wouldn't shift into 6th) and was throwing multiple codes at around 50k miles; the main one being a P0720 for the output speed shaft sensor. Given the TSB related to that code for 2011-2013 6R80's, I am confident that my issue is related to the molded lead frame. I was able to order the molded lead frame, foam strip seal for the solenoids, transmission filter, bulkhead sleeve, and pump pass through seal from my local Ford Dealer for $330 out the door. Definitely worth it and will save many headaches in the future. I actually had a different dealer tell me there was no serviceable filter on my truck, so I knew I had to do this myself. A HUGE THANK YOU from your neighbor in the great state of Missouri.

Thank you so much. I was trying to get my dealer to do this recall because my 11' was acting weird but of course they were saying it did not apply to my truck. Thanks to you and the work you kindly share with us I have been able to at least change fluid but thanks for this latest video I can do this update myself. Thank you again!

You're a lifesaver Makuloco! Just completed this job in my garage this weekend. Defiantly a pain using only jack-stands but I can finally feel safe and confident in my Truck now. These videos mean a lot to me. Also fixed the coolant Y-Pipe Issue and programmed my new TPMS sensors with your videos.

I just changed mine on my 2014 ford expedition. 83k miles. Fault code P0720! Went in to limp mode. Miles to empty went blank and my Tire Pressure Monitoring light came on. Output shaft sensor was the problem. Parks ford of Wesley chapel wanted to replace transmission for 5k! They did not even consider changing the lead frame when I explained to the service manager that ford recalled over 1 million cars and trucks for the same problems. All ford did is perform a software load on 2013 and newer cars and trucks to eliminate the possibility of downshifting into first gear if the output shaft sensor fails. However they still kept putting in the same faulty lead frame in newer cars and trucks. Thanks for your great videos. Big Help! I think the total cost was about 275 bucks with fluid and gasket as well as a new connector. Runs like a champ!

@SevenSixTwo2012

3 жыл бұрын

Awesome and congrats of getting it done. I have a 2014 Expy too, but the trans still is trouble-free at 130k miles (knock on wood!). Did the dealer confirm that all 2013+ are already factory flashed not to downshift to 1st gear?

@georgekrall175

3 жыл бұрын

@@SevenSixTwo2012 They wont tell you that its reflashed but its been updated. They will also tell you that your fluid is discolored and burnt which is not true! They want to sell you a transmission bottom line! Mercon Lv oil will discolor quickly due to the additive package in the fluid. This is normal, and even Ford has a service bulletin out that explains this. Beware of dealer service. Its a dirty game to them!

@SevenSixTwo2012

3 жыл бұрын

@@georgekrall175 Allright, thank you for the information. I changed the fluid & filter last summer myself, it was quite an ordeal. No drain plug + no refill tube makes this job pretty crappy...

You really make it look easy. I don't own a Ford Truck, but with your videos I feel like I can do it all. Nice work! You really love what you do.

You have taught me so much about Fords from real recommended service intervals to what Fords to avoid, THANK YOU! 🤙🇺🇸

Your videos are an absolute game changer ! My transition place wanted to charge me 1,500 to replace my lead frame. After watching your video i changed t my self for just under $300. You are a savior my friend !

This video is gold. It just saved me from having to pay somebody to diagnose my F-150 and fix it. I really appreciate that you made this and made it so clear and easy to follow. Thanks!

i've never got into any transmission work ever, i just replaced the mold lead frame today with no issue, thanks to your video and taking my time i completed the job with no issues so far so thanks for the awesome video, it helped me alot.

Thanks so much for the methodical approach. Every detail is valuable as you know how easily a novice can get caught up with some unanswered question that may be of no concern at all. Your approach makes sure those questions are answered before they are even asked. Thank you again

THANK YOU!!! My 2013 F-150 just went out about 2 weeks ago. I bought all the parts and tools that I'd need and watched this video about 6 or 7 times. I took a few notes and wrote down step-by-step instructions just in case my phone wouldn't load this video if I needed it to. Just like all your other videos, this one was absolutely spot on and gave me the confidence to tackle this job by myself. I didn't even have to refer back to the video once during the entire process. THANK YOU AGAIN!!! Just in case anyone out there is contemplating this job, I was able to do it and I consider myself a "slighter better than the average DIY mechanic.....at best." Also a few notes that may help the next guy: -The front and rear bolts of the trans pan required a 1/4 drive socket wrench because the cooler lines and exhaust pipe are in the way. I couldn't use an impact gun. When I reinstalled them, I basically guessed the torque setting because my torque wrench wouldn't fit. -I only had (3) transfer tubes vise (4) on my 2013. The two to the right (green and blue) were actually stuck to the valve body. The other one was still in the far left hole. -For the life of me, I cant remember ensuring the manual shaft and manual valve were lined up. I think I did it. I've driven the vehicle 40 miles since and everything seems perfect. But I just can remember actually lining the two up. I was got sidetracked torquing the valve body bolts. -Trans fluid starting spilling out after 5.5 quarts. Next time, I'll measure after the 4th quart and adjust as needed. I cant thank you enough for all the videos you make!!!

@FordTechMakuloco

Жыл бұрын

Nice!

@codysturgill3695

Жыл бұрын

Where were you able to find a replacement lead frame?

@santossingleterry2621

Жыл бұрын

​@@codysturgill3695 I found an after market lead frame at Transtar in San Antonio. If you call them they will ship via UPS. I believe they guy I talked to was Scott. It was a perfect fit.

@vicentebchacon

9 ай бұрын

@@FordTechMakuloco Hello, I would like to know where I can buy the transmission module and that the manufacturer is Ford? The link that you leave as a link says that it is not available for the money. Many thanks in advance.

@jaym7369

3 ай бұрын

Thank you, @jonleonguerrero8077, your comment was helpful also! I’m considering doing all this as preventative maintenance on a’15 F150 Platinum

Absolutely awesome the quality of content is unbeatable on this channel 👍.

Very comprehensive tutorial on the 6R80. FTM is your one stop Ford tech channel.

followed this video for 2012 Mustang 6V 6R80 and Mustang is now running great. No more random RPM revs or hard shifting. Awesome video - thanks

I’ve been wrenching for fifty years still have my own shop licensed red seal mechanic this guy knows his stuff

I love watching your videos man. You're such an outstanding mechanic. I wish mechanics today were 1/4 as knowledgeable and mindful as you are. If you lived near me you would be my tech for life. Great job and great educational videos! God bless!

Your video made it possible for me to do this myself. Only took 6 months to find the Lead Frame lol. I also did all parts you recommended at this time . Big thanks you !!

Another superb video on these problematic transmissions. I really appreciate the thorough demo and explanations. Thank you!

My buddy owns a transmission shop he’s a top notch builder. It’s interesting about solenoid shifted transmissions and how reliant they are on other sensors for proper operation. Even large trucks have this style of shifted transmission and anything you ad on that requires action while moving, for example sanders or plows, such as on dump trucks, requires seamless electronic signals to operate properly. Ford is a popular chassis for many things like fire trucks, again example mini pumpers or brush rigs, Ford proprietary electronics are a tough system for aftermarket electronic systems to work with water pumps and other equipment need to communicate with the PCM and transmission sensors. manufacturers are challenged with making electronics that work with Fords.

@bernelfinnegan8563

10 ай бұрын

Hello, is your friend's transmission shop in Florida?

Thank you sooo much for making this and all of your videos. You are truly talented and create some of the best content I've seen on youtube! I don't know how you do these types of repairs AND do such a great job filming and explaining everything that you are doing. I am so glad you made this video. I have a 2013 F-150 and was about to change my trans fluid and filter. I have been avoiding the recall deal with them reprogramming the software because I read about the issues with the mold lead frame thing and knew that the reprogramming was a bandaid fix. I have had zero problems with my trans ( knock on wood) but would like to do everything you just did in this video as preventative maintenance. Where are you located and what would you charge for the service that you just did in the video? Seriously I will drive to you to get it done by YOU. I do not trust the dealership in the least bit, and I don't think I want to do this laying on my back in the driveway. Again, thanks for all your videos, I have learned so much. Been watching for a while. Please let me know about the service.

Outstanding video. Ford had a recall on these in March 2019. My supervisor’s daughter brought in her 2012 or 2013 F-150 for the repair and that lasted for about 9 months. Then it wouldn’t shift out of 1st and the speedometer was showing 0 mph. I did a transmission fluid and filter change in early December 2019 and everything was fine; however, this issue recently reappeared a couple of weeks ago. A friend of mine suggested the lead frame or frame lead whichever it’s called and I immediately looked to see if you did a video on it and thankfully you have. I’m an old school mechanic but your videos makes it easier for us old timers to stay up to speed.

@FordTechMakuloco

3 жыл бұрын

Yeah there was a couple recalls in 2016 and 2019.

Thank you for all your Ford help. This video was awesome. Did everything you said, shifts like a dream now. Saved me big bucks. Aprrectiate all your help.

My 2011 F150 tried to kill me on the highway while towing a trailer. I noticed the speedometer moving around and then go to 0mph. The trans tried to shift into first gear multiple times. It banged and slammed like you wouldn’t believe. This was all before the recall. It got towed to Ford and they replaced the molded lead frame. The recall is abosolute garbage. It’s a bandaid like Brian stated. The trans won’t try to kill you, but you can still get stranded. It’s just a programming update so it won’t shift into first gear, but I believe it will just go into limp mode. Good job Ford! Doing this as a preemptive repair is a good idea.

@jackhenry6268

3 жыл бұрын

So the recalls they dont do this? Going to be buying a 2013 tomorrow and it has had the 2 recalls done. So they designed this new one but dont put them in? I dont get it.

@elvism684

2 жыл бұрын

@@jackhenry6268(Recall) Software Update=$ Installing new molded lead frames=$$$ Get it now. Granted they do install a new molded lead frame if you get a code for it up to a certain mileage and certain years. New trucks should have updated molded lead frames. Not sure with years though.

Thank you for taking the time to make this video. I have a bad Transmission Range Sensor and this video gave me all the confidence in the world that I can do this myself and save a lot of $$. Stealership is wanting $600 for just labor. Subscribed.

@heribertosanchezmendoza8688

3 жыл бұрын

They asked 1700to 1850 to do this job! To crazy behind my wallet!!

@blakehowell6990

2 жыл бұрын

My trucks throwing codes for intermittent transmission range sensor. It will randomly shift erratic and the guages will go crazy where the gear selector is. Does this sound like your issues? What did you replace to fix it?

Thank you for the video. I just knocked it out yesterday. Man without a lift you really work out them neck muscles

Just took my 2012 into the dealership for the second time. Again they just tried to flash the ECM and gave me a runaround again. Of course the molded lead frame is on back order. Like 6 months. So I will have to wait 6 months to do it myself with your guidance. Thank you sir.

This is the kind of job where a lift is your best friend!

Another home run, on this trans service repair.

I personally want to thank you for this video and all the information and support that you have provided. I ordered all the parts and my son and I replaced my lead frame and the other parts you have suggested to do. It was a breeze to do because of you. I ordered through you on Amazon. Thank you so much

Followed step by step and the trucks now running again and driving great only problem I had was a 8mm pan bolt that was stripped from the previous owner/repair lol can't ever have a job go to smoothly of course. Buy thank you for all the videos you put out they have been total life and money savers!

Seems like these lead frames are going out everywhere. All the ford dealers near me are out of stock. Thanks for sharing your knowledge!

@fernandobriseno8164

3 жыл бұрын

Yeah I'm in the same boat, been looking around to buy that part 😤

Your videos are some of the very best on KZread and this one doesn't disappoint. Thanks for the extra effort you put in to making such high quality videos.

Thank you for the video,done mine in about 3 hrs longer for it to drain and put fluid back in it than it does to change to change the lead frame

Simply amazing. Incredibly generous effort

I love watching this dude he's thorough no bullshit gets to the point and so far if you follow him word for word you'll be fine...knows what he's talking about.... always good videos... just wish he'd stated the cost for the parts usually....or I may of just missed it

Very well presented! The close-ups of the work area, the procedure details, and the technical information were of great help to perform this operation seamlessly. By the way, I have a paralyzed right arm and this video gave me all the necessary knowledge to complete this repair. Thank you and keep on posting.

Thank you so much for sharing your expertise and knowledge! Guys like you have saved me tons of money!

This is the only thing that has failed in my 2012 Expedition in 108K miles. Ford fixed it under warranty via a recall; great service at the dealer near my house!

@kylekirchner1163

3 жыл бұрын

Robert Cope were do you live? Where I live you would be better off taking your car to Walmart.

@robertbcope

3 жыл бұрын

@@kylekirchner1163 I'm in Houston. I was surprised, as well, but the experience at the dealer was fantastic, particularly given that I had never set foot in the place before in my life. Who knows if the quality of the work was great, but the truck hasn't missed a beat since getting it back.

you make that draining look easy, my driveway looks like a massacre happened

@Quick_Fast_Hurry

9 ай бұрын

🤣🤣🤣

You do a Great Job, not adding lot of unnecessary blabbing. I've been working on cars since I was 12 and it's nice to see what I'm getting into first hand instead of the old day Motor/Chilton manual pictures / procedures.. Thx Again!

Success thanks to this video. 2011 F150 5.0 w/ 209K I had an intermitten no crank no start. This issue developed as an occasional delayed start when turning the key. Noted that the dash gear select indicator light would not illuminate in failure state (P would not be orange) Eventually, progressed to where I could put the key in and turn 5-500 times before the indicator would illuminate and allow for a regular start. Ordered the OEM Lead frame, coastal sleeve, pump pass through and fluid from a dealership. I had a fluid change and trans filter replaced less than 10 mos ago otherwise would have changed the filter too. Although the trans pan gasket could be reused, I had to pick up an aftermarket at assembly time due to damage noted at the flexible point on the old gasket. This video was great to eliminate any surprises. One deviation I had was 2 of my transfer tubes were secured in the trans and 2 were secured in the valve body. No big deal as none of them were loose, just an unexpected configuration. I put the front end on jack stands for better access. This still allowed me to fill the trans when finished, I did take them out for the final fluid check though. Glad I printed the torque specs and tightening sequence as that was very handy to have during assembly. Grateful to have found this video. FordTechMakuloco, thanks a ton for creating and sharing this. As others have said, you are a good communicator and effectively convey necessary info. With gratitude, Dennis.

I'm very able, but if not, I'd drive all the way from CA to have YOU service my Mustang ;-)

I had to do a service to one of these recently..as our shop has a machine with a powered vacuum hose...I removed the 19MM plug for the fill hole and just sucked out all the fluid before dropping the pan...real clean job at that point!

@915greenhornet

3 жыл бұрын

Best tip yet

@blainemcdonald6972

3 жыл бұрын

THATS A GREAT IDEA PLUS YOU WOULD EXACTLY HOW MUCH FLUID TO PUT BACK IN

Great video. 30 years as a mechanic, first time I had to deal with this issue on a 2013 Ford F150. You are spot on! Replaced lead frame and the truck back on the road. Thanks for the information!

@fluevano1204

3 жыл бұрын

where did you find the part? dealers are out of stock

@tuneuptony3679

3 жыл бұрын

@@fluevano1204 we waited for 4 weeks for it. I think my work ended up buying it from another dealer. A stock order came in and they had 1 extra.

@bigb6548

2 жыл бұрын

Had anyone had issues after all the fluid change I'm at 155k and currently getting fixed. Just curious if I need to worry about anything after

@mattmorgan5370

2 жыл бұрын

Did you have to program the module when replacing?

@tuneuptony3679

2 жыл бұрын

@@mattmorgan5370 I did not.

My 6R80 is 2010 model year but I watched the whole video anyway because I like your videos so much 👍. This one was excellent as usual nice job.

Master of master fantastic video.

This is a great video! Thank you for all the amazing videos you provide. I just purchased a 2015 Expedition. It has 100k miles on it. I am planning on dropping the pan for the filter and fluid change. Are you saying this service should be done as a standard on every 6R80 transmission if it has not been done? I have not gone this far into a transmission before so it would be my first time. If I am dropping the pan I might as well do this if it is recommended.

@joelusa1

3 жыл бұрын

I owned a 2011 expedition el and ordered all the parts associated to the issue, I am now calling Ford if it's needed but I will replace it just for the heck of it.

You are the best. Watch your videos all the time. Brothers truck decided to give up right before vacation. Swapped out the lead frame and was back in good shape. Thank you, k

Thanks so much! Shop quoted me 2k. I used your affiliate links along side this video. $500 and 3 hours later we’re back and running properly. 👍

THANKS for the great video, My 6R80 harshly shifts from 1 - 2, and also 2 back to 1 i dont think my 2011 trans was ever upgraded... would replacing my lead frame as you did help mine, thanks again

@joshuaj6657

2 жыл бұрын

@Spiro Flying @FordTechMakuloko I would like to know this as well as I have the same issue!

You beat Scotty Kilmer to the punch on this. All he can say is “Get a Toyota”.

@pmartinagejr

3 жыл бұрын

Both Scotty and this guy are great to watch.

@xoxo2008oxox

3 жыл бұрын

@@pmartinagejr Sorry but you can't put Scotty in the same league as FTM...Kilmer is just not as instructive and thorough.

@kimdavis5631

3 жыл бұрын

pmartinagejr Scotty is not a master/specialist like FTM. He is a ‘jack of all’ kinda guy.

@whpony96

3 жыл бұрын

Scotty Kilmer needs to be removed from You Tube nothing but BS spews from his pie hole.

@pmartinagejr

3 жыл бұрын

@@xoxo2008oxox l absolutely agree. Mukalo is a Master Mechanic and has great instructional videos. Scotty is more of an opinion guy but is certainly entertaining

Thank you for explaining step by step how to change molded Lead frame. Your video is great.

This helped me immensely. I have a 2014 F150 STX, speed sensor issues, odd driving, no codes (yet) but all sorts of weird shifting. Followed this video , bought the parts, drives 100% now. Thank you.

How can you tell if this repair has been done to my f150 ?

This design looks very similar to the ZF 6HP19 in my BMW. There must have been some collaboration with ZF?

@FordTechMakuloco

3 жыл бұрын

yup

great video. Just completed my daughters 2012 Mustang and this video was perfect. It addressed everything that a person needs to know to successfully do this job. Thanks!

Excellent description of failure points and fix. Top notch video, thanks.

Ford Engineers: "We've got a new 6R80 transmission that doesn't use friction bands or servos!" Accounting Mgmt: "So simpler construction? Great - less cost and more profit for us! Any issues?" Ford Engineers: "Well, the vehicle may drop out of 6th gear at 60 mph to 1st gear, destroying the trans and possibility over-revving the engine, destroying it too." Accounting Mgmt: "No problem - we can blame the consumer for not performing regular fluid changes like we did with the DCT trans - NEXT!" BTW - great video Brian! Clear and concise - you made it look easy enough for any shade-tree mechanic to perform. Cheers!

@zenbhudda8342

3 жыл бұрын

It’s ZF trans By VW

Brian, you always make it look easy. The sign of a real pro! ?: Why do manufacturers avoid a drain plug on the transmission pan?

@Squat5000

3 жыл бұрын

Sealed for life. It ensures it hits its target life of 60K miles in this vehicle (warranty duration) and then explodes shortly thereafter. Same with differentials and many other components.

@officialyoutubecommentator4357

3 жыл бұрын

@@Squat5000 100% correct because there is no other way to swap out the trans fluid.

I'm a pretty green diesel mechanic and this video was so helpful. Thank you very very much.

Dude, you are concise and very easy to understand. I believe you are the best. Also a badass

If im getting a 2-3 jerk but only on 2-3 would that be a shitty solenoid? it doesn't jerk if i'm stepping on it and getting the rpms up in the 2.5-3k range or higher, but will jerk hard at slower accelerations and deceleration but not always. filter and fluid was replaced few thousand miles ago to fix a leak. it was all oem ZF fluid and filter. could the leak have damaged a single solenoid but none of the others?

@martinbramston2244

3 жыл бұрын

Hi Fishfind3000 ,I have the same problem on 2nd to 3rd gearchange, only on that one ,the other gears change smoothly . Same as you with no issue when under hard acceleration. Thought it was solenoids A and D ,and recently changed them with no benefit at all. Will pull it apart again and replace solenoids B and C to see if any improvement .Will let you know results . Martin

All this is easier if you turn the vehicle upside down.

@kevingiltner5560

3 жыл бұрын

Customer wanted the french fries left under the seats though or else he...

@livenfree

9 ай бұрын

😂 Can you please make a video showing me how to do that safely? 😊

Have a 2015 expedition el with 190k miles. Just starting to have moderate issues Here and there but kid because I've maintained it according to your videos. Thank you very much haply new year!!!

Absolutely great video, did mine like a pro this weekend 👌 I ended up being able to get 9 qts in on the fill. By far the most pain in the ass part of the whole job

@mattneal4941

Жыл бұрын

Does this have to be programmed?? I just bought and updated valve body and lead frame assembly.

@marcjorgensen

Жыл бұрын

@@mattneal4941 nope

And this is supposed to be a better idea. What does it take these days with all of our technology to get a simple, tough, long life mechanical component. Its ridiculous !!! Develop a simple brute of a transmission without all the silly gimmicky stuff and leave it alone. Why change it every few years, its just a transmission. Why do we as consumers have to keep paying for their stupid, impractical, incredibly poor designs ???

@blainemcdonald6972

3 жыл бұрын

THE NEW TRANSMISSIONS ARE WAY MORE EFFICIENT THAN THE OLD BAND OPERATED TRANS, THE NEW SOLENOID OPERATED TRANSMISSIONS VERY CLEAN FLUID . FOLLOW BRIANS RECOMMENDED CHANGE INTERVALS AND YOUR TRANSMISSION WILL LAST LONGER

@outlawgentleman8860

Жыл бұрын

Uhhh money that's why

@JoshSmith-wo7zw

Жыл бұрын

So they get better fuel economy and shift smoother.

This looks like the 6 speed ZF's used in bmw/Audi's.

@FordTechMakuloco

3 жыл бұрын

It's based off the ZF design yes.

@FishFind3000

3 жыл бұрын

I bet they work together on them or zf builds them with fords designs or vis versa.

@FishFind3000

3 жыл бұрын

18:20 that yellow part with 2 squares is a part that was replaced on my zf 6hp19 when I did a trans flush and replaced all the seals as well as that connector seal. that one was leaking on mine. there is a strong resemblance to zf

@alb12345672

3 жыл бұрын

@@FishFind3000 They licence the design and intellectual property. Then they can build it and save a few pennies :). I think some Fords had the real ZF in some cars.

@FishFind3000

3 жыл бұрын

alb12345672 makes sense

I've never worked on a car before, but watching your videos makes me confident that I could do these repairs.

Your videos have been a huge help for our shops

Too many electronics in vehicles. When they work, they work, but when they don’t, a program cannot dismiss a simple fault to keep you from having a catastrophic accident.

Dear God...talk about poor designs that could lead to a tragedy.this electronic stuff has gone way too far.

@oldschool9746

3 жыл бұрын

Not much common sense in automotive engineering anymore.

@pl5624

3 жыл бұрын

@@oldschool9746 hasn't been in decades.

@richardcranium5839

3 жыл бұрын

all driven by the need to meet fleet emissions and fuel mileage standards. the standards have outpaced the technology

@joe1273

3 жыл бұрын

Thats alot of hype the pcm has a strategy to keep it from going into 1st. It uses wheel speed sensors and will throw an oss code. It may go into first at low speed but it will never go into 1st at 60mph.

Just changed mine out. Had limp mode on and off for about a week. Video saved me fr. Thank you

Thanks for the detailed video. Going through this fix on my 2013 navigator. Navigator made it 205,000 on the original lead frame. No mechanics would take on the repair and no ford shop in town so I’m following your video and it’s going smooth so far

I have removed a gallon and added a gallon of Redline synthetic fluid just about every other oil change. Removed the 19mm plug to do it. A sensor went bad back when I had 268,000. The Ford tech was happy as could be because I exchanged my transmission oil. Rebuilt my valve train, sensor and a new filter. 303,000 miles now and just went up Mt. Ellen in Warren, VT to a cell site. 2012 Expedition. Enjoy your videos, really informative. I have learned a lot.

@alb12345672

3 жыл бұрын

For a real test you can drive it up whiteface :lol:

LOL first thing I noticed was the Anti splatter matt, I love those things. Great Video

You're awesome. Going to do this repair soon. Got a no start on the truck a few days a go and was reading forums on what it could be. This sounds like the culprit.

dude this video is top notch. this has certainly given me the confidence to do it on my own without half-assing it as i usually do!

Great job on video/trans repair. You made it so easy to get those replacement parts.

Great video, thank you so much for making this video! 👍👍👍👍👍 I'm going to do some long distance, mountain driving, so I want to get this change out and rebuild done before I do that. This really helps!

Great stuff yet again. I have the 10R89 in my 2019 f 150 and waiting (forever probably) for them to address a lot of the issues it’s having.

"No sweat!" Your videos are so detailed and helpful.

unbelievable how informative the video is..THANK YOU

Thank you so much! Im by no means a mechanic but your video helped me every step of the way i took a while but got it done🔥

Thanks. This video helped me a lot. I completed this repair with no problems. Luckily I bought the lead frame over a year ago. It’s not available anymore. This fixed my hard shift from 5th to 4th gear.

@mattneal4941

Жыл бұрын

Does the lead frame have to be programmed? I just bought and updated valve body and lead frame assembly.

@Raydarman1

Жыл бұрын

@@mattneal4941 nope

In 2016 I used your video of a 2002 f150 rear axle seals replacement..It was a challenge, but your step by step instructions were flawless. Thank you so much for being so meticulous, I saved at least 1k on the repair. Marry Christmas Billy #3

I appreciate you. I've only been here for a year.. your strength I hold.

First off. I absolutely love your videos and you are a very valuable asset and a true master in my opinion. I am going to install a TransGO shift kit in my 6R80 In my 2013 F-150 during the 100K service along with the filter and other bits you pointed out. I just received the (Supposedly) updated leaf frame (AL3Z-7G276-D) and it didn’t come with the foam strip. My dealer is telling me it’s a separate part. So I just ordered that also ($26) seems like a lot for a little strip of foam.

Great Video! Made servicing my F150 much easier! Fluid, Filter, Molded Frame, Connector, Seal and Gasket replacement.

Thank you @FordTechMakuloco for another great lesson on how to get the job done... I am about to do this job on my F150 pending a couple of suppliers that have complete valve bodies and refurbished OEM lead frames. Thanks man.. you rock! And I finally found a part supplier in FL that has this lead frame in stock... took some finding, man these lead frames are like hen's teeth these days.