Good ole local machine shop. That part was a quick fix for them. Wham bam here you go Sam. Good Lord was watching out for both of y’all

@SoybeanFarmer3300

Жыл бұрын

Same shop that built the engine for the dump truck they do good work down there.

It's been years since I replaced a wheel hub. You did an excellent job of explaining each step for a novice. Job well done.

@SoybeanFarmer3300

7 жыл бұрын

only if I'd pulled those hubs years ago I might have been able to do a simple rebuild i.e. replace races and bearings and not have to buy new hubs. negligence can be such an ugly thing. costly too. thanks for the compliment and for watching.

The reason that the hub was rubbing on the bottom of the casting is that the thrust bearing at the bottom of the spindle had completely disintegrated!! The thrust bearing keeps the spindle in the correct position so that what you experienced doesn't happen as well as the spindle rubbing on the bottom of the casting itself. The hub was not the wrong size. If you were already taking the hub off I would suggest to replace the two spindle bushes and thrust bearing too. Thanks for sharing your video.

Daddy and overhauled the front end on our 5000 . It didn't release how bad it was till , I drove it down the road after we finished. Thanks for sharing this video!

@SoybeanFarmer3300

7 жыл бұрын

when I found out how bad my 4000 was 7th and 8th gears were not used. tonight when I get home, if the rain has stopped, I see a test ride. thanks for watching.

we'll enjoy your video and how you explain things I'm so glad you keep making them. one thing nice about making videos to get the talk through it to make sure you're doing the right things. and if you have to do it again you can go back and watch it. hope you have a good evening

@SoybeanFarmer3300

7 жыл бұрын

"go back and watch it" the camera was running when I flung a fit after realizing the hubs were actually the wrong part for the tractor. it was about a 2 minute rant before I calmed down. certainly not suitable audio for all age groups. it was good to see how the elevated blood pressure did not produce the result of magically changing the hubs into the correct part and just how worthless getting that upset was. yep going back and watching something again does have a certain measure of value. Elm custom harvesting, your comment here has within it a tremendous value, thank you for saying it my friend.

Brings back memories of the day my front hub broke on the 4020, that flange with the studs broke in two. I was using the loader to haul sand, apparently it was too heavy! Good thing was I used the loader to lift the front off the ground so i could replace the hub out in the field!

@SoybeanFarmer3300

7 жыл бұрын

that for sure was a matter of convenience being able to use the loader as a lift. this reminds me I need to lift the 4020 and check the wear and possibly adjust if necessary. thanks for saying 4020. :)

I like the improvisation bud! Seems like you have my luck!! Keep it up bud.

@SoybeanFarmer3300

7 жыл бұрын

the choice was week and a half mail order turn around or trip down to the local machine shop. lost my mail order savings at the machine shop but at least the job is done and over with. thanks for watching.

There is a video by 'Bundy bears shed' called 'How to change your front kingpins' I would recommend watching it as I think you may have to do that job too if you havent already. Good luck !

@SoybeanFarmer3300

Жыл бұрын

This repair was done back in the year 2016 and later after revisiting the issue I found exactly what you just described. Thanks for pointing it out and stating it like you did, gave me kind of a nice feeling. Thanks for watching the video I hope you'll come back and watch some more.

A bearing puller would work too put in the bearings. You could attach to the outer rim of the hub and push the bearing in square. Your method works but there is always a danger that you go off square and your bearing gets stuck. Great video.

@SoybeanFarmer3300

3 жыл бұрын

Thanks for watching. Yeah I agree bearing puller would pull it in straight there's always a risk with driving it in. Getting these new hubs and getting all this rebuilt sure did improve the tractor.🙂☕🇺🇸

Good video as always. I spent a lot of summer doing that job, I got to be darn good at it.

@SoybeanFarmer3300

7 жыл бұрын

job not all that difficult and even better when having the correct hub. thanks for watching.

You change wheel studs on the tractor with the wheel on. Just take the nut off and hit the stud inwards with a hammer. Then use the nut to pull in the new stud just do one at a time with the wheel ON. This way stud stays Square Just a tip, done it this way on old Ford for years

@SoybeanFarmer3300

6 жыл бұрын

David Watt - thanks for the tip and for watching.

@WillsBullies

3 жыл бұрын

@@SoybeanFarmer3300 Hi where did you get the hub they keep asking me for part numbers?

Aint trying to be weird or nothing but where are you in NC? Like the Piedmont mountains or coast

@SoybeanFarmer3300

7 жыл бұрын

piedmont. kzread.info/dash/bejne/n5-pq61yj8XNp8Y.html

Hi, I have a 71 4000 I need a new hub and rim do you know where I can get them ?

@SoybeanFarmer3300

3 жыл бұрын

I bought those here: www.reliableaftermarketparts.com/

@WillsBullies

3 жыл бұрын

@@SoybeanFarmer3300 Thank you

im from coats not to far from you

@SoybeanFarmer3300

7 жыл бұрын

Hi Jack. been years since I was in Coats. you or your family farming there?