A segment about setting timing would be helpful as part of the ignition overhaul. The shop manual description is a bit wonky so seeing it live would be helpful. Thanks for all you do, these videos are excellent.

Very comprehensive but I watched one of your 4 cyl 9n tuneup videos that threw me off. In that video you mention distributor rotation and stated that all distributors newer than a particular date rotate clockwise. I assumed that meant for the newer 3600 3 cyl as well. I doubted my own documenting of my wiring and assumed I had mis-traced my wires which indicated a counter clockwise rotation. I finally removed the new cap to watch actual rotor rotation and verified it is, in fact, counter clockwise. It would be worth mentioning in this video. Otherwise, you've taught me more about this tractor I inherited than I've been able to find out anywhere else. Thanks for these wonderful videos.

THANK YOU FOR COMING BACK AND LETTING US COMMENT... This channel has helped me with my farmall's

@DanGingell

2 жыл бұрын

Our pleasure!

@patkelley2190

2 жыл бұрын

@@DanGingell thank you both for the help .

Bravo, Rachel! Was using it Friday ('67 Ford 4000 Industrial w/ Ford 737 front end loader) . 30 minutes into job it died and refused to start again. It has never done this before. Had plenty of fuel in the tank. Suspected fuel line blockage but, pulled a spark plug before pulling and fuel lines and discovered we were not getting any spark. Decided to replace coil, and all the ignition parts you recommend in your video. Can't remember the last time this was done...probably 20 years ago. Your video was great for reviewing the process of replacing all the ignition parts. When my local NAPA guys could not find the condenser for the repair I canceled that order and ordered everything but coil and spark plugs from you. You have impressed me so much that I subscribed to your channel and created my own KZread channel just so I could comment on your video. Plan to look into everything you have on Ford 4000 tractor repairs. Wish you had one on how to replace the rear main engine seal. I'm having a tough time finding anyone in southeast New Mexico that works on these awesome little tractors.

Just brought home my "new" 65 Ford 4000 today and this was the first video that caught my eye. I'm very happy I watched it. New subscriber!

Rachel, this is an excellent job explaining the electrical circuit in the motor, I have such information and have been working with it in the past. Thank you 🙏

@abuabdallahalutiby5161

2 жыл бұрын

Thank you for highlighting this reply and I am happy to follow all new you and your father..

Such a professional channel this is, keep up the good work

@DanGingell

2 жыл бұрын

Glad you enjoy it!

Mighty interesting. I love working on old engines!

Thanks ya'll for all the sharing. I keep waiting for some Massey 35 Diesel videos, but THEY NEVER BREAK! Lol, just joshing.

Thank you so much. I just came here to get help with my Ford 3000 and saw this!

love it. thanks so much for this content. just ordered the service manual!

Great video as always Rachel !!!!!!!!!!!!!!

Great video thank you for all your hard work

Great videos. I have a 1965 Ford 4000 Diesel. Would love a video on troubleshooting won't start.

Great tutorials. Excited to see a channel so dedicated to the cause. Exactly the kind of quick-transfer of knowledge I was looking for. Just acquired a 1969 Ford 2000; one that has been sitting for 6 years, but absolutely certified as 'ran-when-parked.' So, we'll wake the old girl up, on site, and take her home under her own power.

Great job always helpful information. Thanks 😊 🙏

Very thorough, articulate and easy to follow instructions

Great video. Thank you. I’ll be ordering parts for a needed tuneup on my Ford 3000 soon.

Great video and good job explaining things. Take care and have a blessed weekend and I'll see you on your next video.

Thanks for all these videos they are great.

Good job Rachel. I made a similar video last fall. I always learn something from you and Dan so I encourage you to keep creating and posting videos. It's challenging to keep our old tractors operating. Thanks.

Blue Streak used to sell some stuff called "Lubricam" put just a little on the cam that the points run on, and your points will stay in spec and last longer too.

thank goodness this vid is up......great photography and flow....nice!!!!......

Great job, one of the best I have seen !!!

You are incredible. Very helpful

Another wonderful well done video

Great tutorial

Awesome video!! It helped me a lot!

o-my this is just what i needed on a cold winter day is to watch a hot tractor repair video. 🤩 gee, it would be interesting to see the factory workers make the old tractor parts. 🧐🥳

Very thorough video

Nice work

Great Video

This was super helpful

I own a ford tractor 2000. 3 cyclender your such a good teacher thank u so so much

I am rebuilding the harness, carburator, and distributor system from a tractor that caught fire and matches exactly the model you are working on, I hope your website has all the parts needed! I also noticed you didn't address the missing vacuum line, it's purpose, and that the newer distributor assemblies don't require the vacuum line from the manifold above the carburetor.

Thanks. My father in law left us a 2000. He didn’t believe and buy a new parts. He believed in finding something you could make work. When you’re a mechanic, I guess you can do that. But I’m a plumber, so I just go by what the book says. The problem is things like the neutral safety switch aren’t even wired up anymore. I ordered that thin manual. But there’s no troubleshooting section.

Fantastic👍

Thank you Rachel, you da Lady.

You are a big help

She is awesome!

Hay Dan thank you for your help from over the phone call. Ford 1964 4000 industrial . Found the trouble in loose plate on top lid.

Ford 3000 is my dream tractor .one day I'll have one !!!

Extremly good.

شكرا رشال على الشروحات القيمة في مجال ميكانيك الألات الفلاحية الذي هي نفس مهنتي ربما تختلف الجرارات عندنا في الجزائر، هناك انواع جرارات قديمة مثل الماسي فيركيسو والفورد الازرق نفس الذي رئيته في حلقات معك سابقة

Man I wish my son would meet an pretty, smart, and incredible lady like this. I have two tractors that are always breaking.

You show the tuneup but do you ever need to reset the timing? Where is the timing mark? Thanks, Don

Can you show how to remove an injector on an 801 ford......please.

First...I LOVE YOUR VIDEOS! Question: In the manual it states the firing order is 1 2 3 and the rotor rotates CCW. The #1 starts as indicated in the distributor cap (You continue to state it could be different on your tractor) All gas 3000's have the same firing order and distributor rotation, you state several times you are putting the number "1" wire on the cap first then putting the cap on because of manifold clearance issue with #1 wire. That is ACTUALLY the #2 wire that is having the clearance issue with the manifold. Watch your video at 17:04 you can see the #1 in the cap just to the left of your right index finger. The number one wire you are referring to is really number 2; Correct? since its a 3 cylinder it may not matter as long as the order is 123 on the distributor in the CCW direction. :)

@erics3101

2 жыл бұрын

Hello collie, I think you're right and I'm putting one back together for a guy and I know the firing order is 123 but is that counted from the radiator or the back of the motor?

I love your videos. Thank you very much and your father too I guess.

Does Petronix make a kit to get rid of the antiquated points setup? It looks the same as some older v8 engines we changed.

Great shoe young lady 👌 👏

Should your test light blink on both sides of the coil when turning the motor over?

Great tutorial, and clearly the distributor on this tractor did need some work, but is it not true that the noise it makes at 2m30s when you try turning it over is a bad starter?

Can you do a video on fuel air lock in lines I re did my carb and started it . it whistled very loud then I put another gasket on it stopped. My gas lines had rubbor selves on them that went into the carbirator front and side is that why??

Love it i have ford 3000 diesel engine 1973 model

Does any of this apply to a Ford 340 industrial tractor?

is that an american version, becouse i have a ford 2000, and it has no sparkplugs but glow pins, nor carbouratour but a central injection, no distrubuter connected to the camshaft, it tanks diesel, has the front lights on the front grill and can you cover the hydrolic system? Mine is having issues lifting heavy things and keeping it in the air, the hydrolic pump has to step in constantly

working on this 3000 and got the points replaced. Unfortunatly I dropped a screw and had to pull the distributor. I'm betting i screwed up the time because it backfires when I try to start it now. At least I know I got spark and fuel. A step closer. So I 'm likely not in too bad a shape. I didn't turn it over while I had it out. Hopefully I can figure it out. Mechanics isn't my strong suite. lol Do you have a video on setting the timing?

I’m not getting at spark at all and have replaced everything. Coil, condenser, cap, rotor, wires. Turns over but no spark.

excellant show on job have one question ford tractor i bought # 1 was at back of motor you say front maybe person before me did wrong why wont run its a 3 cylinder please help me thank you

Hi Rachel how do you set the timing on a 2000 gas ford tractor

Cool

Does the Ford 8 n solenoid ground with that metal bracket?

I have a question sure hope you answer it. I replaced everything that is in this video. I have no spark. So i tested it with a spark tester(in line type) i have spark and tractor starts up with the tester connected but as soon as i remove it wont start no spark. Any ideas what would cause this???

On the hopes that you watch comments on older videos … do you have a source for throttle springs for the Holley on a 1968 Ford 3000?

Can i put a electronic tac on my tractor off of the coil

No love for the 5000? Just about everything you mentioned applies to that machine as well. What's your opinion of ditching the points for an electronic ignition like the Pertronix? Also allows you to convert the ignition to a full 12v setup. Love the videos. Agree that the large White manual is well worth the $$.

@ShainAndrews

2 жыл бұрын

We convert everything to electronic and 12v. If a person has the means it is money well spent. Especially if equipment is left outside year round.

What gauge battery cables for ford 3000 and length

All well and good, but I'm having trouble with my 1963 Ford 4000 6-volt charging system, and no YTrs have covered this in concise understandable terms and provided a functional schematic diagram for the regulator or an explanation of how/why it works or doesn't. In fact, there is very little information out there for this tractor. My generator shows it is charging, but after running the tractor even 5 minutes, it fails to restart because the battery refuses to turn it over. I've worked on this for days, searched for relevant information to no avail. Any advice? (apart from just junking this POS).

why would not clean inside of the distributor before you install new parts?

Very informative. Thank you. Also tractors are meant to be diesel powered.

What manuals cover a 1975 industrial loader backhoe Ford 4000 3cyl Gas ?

Dear rachel gingell, here we have mf 240 in large scale production in pakistan... So we have basic problems with mf240 since it has been invented... 1. Poor internal hydraulic pump...so can it would be mount externally like fiat 480....no.2 is low pto hp... So can we increse its pto hp by modifying or changing pto gear...

also on cap does it go clock wise direction on three cylinder ford

@Bradm88

7 ай бұрын

We have a ford 3000 and it goes counter clockwise.

I never had a dust cover on my 8N tractor. Did they once have one from the factory, and should I buy one and install it? Only use the tractor to cut the grass, and plow show, not disk a field of dry soil.

@DanGingell

2 жыл бұрын

The 8N side distributor was not originally outfitted with a dust cover. The dust cover was introduced for the Jubilee model and later. Please see this video for a tutorial on that specific distributor, and a more detailed explanation of the dust cover: kzread.info/dash/bejne/iWF-t8eImLfbqNI.html

@lostinmyspace4910

2 жыл бұрын

@@DanGingell Thanks for your feedback. I'll check the video you suggested now! FYI...I had Dan Gingell convert my 8N tractor to 12 volt way back in 1994 when the shop was on Lapeer Rd. THUMBS UP!!!

pleage, Belarus gave a video of the steering column on the tractor

Hallo Rachel can you help i need a Starter for a international TD 6 or a Part number thank you from Germany

Have you any interest in some pdf manuals? Nicely done video as always. Personally I never cared mush for 3 cyl. gas engines.

Don't you guys have Diesel ford tractors in the US ?all our ones seem to be diesels in NZ.

Fuel, spark……..air Rachel, you know this. And valves making this happen.

Thank u

👍👍👍👍

Satishmulge🎉

Plz make one ☝️ video for timing fire order for Ford diesel 3000 ,3600

Just an FYI regarding some 3000/3550 systems. At kzread.info/dash/bejne/pGuEu6qSqK7SiKw.html your test is overlooking one possibility that occurs on my 3550. The rearmost coil terminal shows voltage with the ignition switched on, but it disappears when the starter is engaged because some ignition switches don't provide coil voltage in the start position (like mine). There is a secondary contact in the starter relay that is supposed to provide that while cranking but I've had two relays fail. I start mine now by connecting a push button switch between 12V+ and the rear coil terminal. I have to hold the switch closed while cranking to start the thing. I'm going to install a permanent push button switch instead of replacing the starter relay again.

I’ve got a Ford 2000. I can’t get power to go to the starter. I replaced the key switch the regulator the coil. I am at a loss and out of my element. That thin manual doesn’t have any trouble shooting section. It was a waste of money. I’m gonna see if I can find a digital copy of the thick manual. In the meantime, I will take advice from anybody.

You are so lucky yours doesn't have a Loader on it.... Impossible to fit tools in there.

2000 Ford tractor tune up.

861 Power master videos please

Olet kaunis nainen olen ihastunut ja kiinostunut sinun haluan tavata sinua 🌹🌹🌹🌹🌹🌹♥️💋🤠👍🏻

That's weird. That big tractor only has three cylinders, but my 8N has 4 with a firing order of 1-2-4-3.

¡Usa guantes, Rach!.

can anyone answer my question?

Thanks for the video...I would also like to say that you're absolutely beautiful...and I love the slight accent

Been working on a family members tractor for a month now. They thought it was an electrical problem and ended up burning the entire harness. So I replaced all the wiring. No luck starting. Rebuild the carb. Still wont fire. I'm doing the timing now. How about you come fix it for me. I'm getting sick of working on it for free. Ford 2000 3 cyl gas. I own a ford 5000 diesel thank god. So much easier to work on.

when you put the distributer wires on you have black gloves, when you put yours hands in the nasty transmission you have bare hands ha ha ha me too

Everything was great but you left out the timing which is critical!

This video didn't help me at all. Mine's a diesel.

@sgg17003

Жыл бұрын

Your complaining doesn't help anyone at all. The video helped a lot of other people. Negative people suck. Fix your tractor and get some fresh air to clear out your mind.

@chuckfinley4757

Жыл бұрын

@sgg17003 And your reply contributed what to society?

@sgg17003

Жыл бұрын

@@chuckfinley4757 No much, but it didn't scream "Hey world, I'm a whiney douchebag" to the world like you did. Instead of crapping on the great work that people do for free that helps out everyone but you, you could have moved along. So yeah, if calling you out makes you just a smidge less of an a hole, then I did contribute to making the world a better place. Now if you don't mind, I'm going to watch a Chef Ramsey video on how to cook a perfect burger and complain that it didn't help me because I'm planning on cooking fish (see how douchey that sounds? Yeah, you brought that on yourself).

@chuckfinley4757

Жыл бұрын

@sgg17003 Oh the ironic tone in your replies.

Hi. I'm having trouble with hydraulics on farmtrac 60. Was wondering if you could help me out with it. Is there a way to contact you. Email or text

@DanGingell

2 жыл бұрын

Hi Mike, We do have some familiarity with FarmTrac tractors and would do our best to help you. Please schedule a call at this link: farmtractorrepair.com/collections/tech-support/products/schedule-a-phone-call-for-mechanical-help

Dear rachel gingell, here we have mf 240 in large scale production in pakistan... So we have basic problems with mf240 since it has been invented... 1. Poor internal hydraulic pump...so can it would be mount externally like fiat 480....no.2 is low pto hp... So can we increse its pto hp by modifying or changing pto gear...