These are the Tools and Parts needed to complete this job: Thermostat Housing Assy (check fitment guide)- amzn.to/2sZIxOr Vacuum Fill Tool (an absolute must on these engines)- amzn.to/2sZzRYo Alternate Cheaper Vacuum Fill Tool- amzn.to/2t6Lu0b Coolant Burping Funnel- amzn.to/2s327Kn Gold Coolant- amzn.to/2rZBUMS or depending on model year OAT Coolant- amzn.to/2t48mgN How to use the Vacuum Fill Tool- kzread.info/dash/bejne/kYt3tMWuc72vZZM.html How to remove stubborn air pockets from your cooling system- kzread.info/dash/bejne/ZpufltqbacS1l6g.html

@PalmettoMoon

7 жыл бұрын

FordTechMakuloco A fellow youtuber highly recommended you! I have an 2006 mustang Gt 4.6L coupe hardtop premium edition. I need to know if my transmission is a 5r55w or a 5r55s? I've beat my head against the wall for a week now trying to find this answer. Please help!!!

@FordTechMakuloco

7 жыл бұрын

It has a 5R55S, I have only seen the 5R55W in some Explorers.

@PalmettoMoon

7 жыл бұрын

FordTechMakuloco Thank you so much for your time! New sub here☺

@raphatang6050

7 жыл бұрын

FordTechMakuloco in

@alvarosilva957

6 жыл бұрын

FordTechMakuloco i got a 2010 ford fusion. 2.5 se my fan turns on on highway speeds. Passing 70 on a 20 min drive. But the. Temp needle stay in place would this be the issue. No code at all

i paid my buddy $50 bucks to do this for me. he said the same thing, just leave the hose on it swap it over and re install! you can tell great mechanics think outside the box! you sir are a great one!

As a former flat rate tech (20+years at Ford & GM, now in fleet maintenance) I really appreciate the sharing of your knowledge. Having this kind of information available is a time and money saver! All your video's are very helpful. Thank you and best of luck with your FordTechMakuloco You Tube Channel.

This is by far the easiest guide for dealing with that sucker of a thermostat. Dropping the fans is a simple and easiest way to get enough room. I've seen others remove the drive belt, engine mount, power steering pump and reservoir, or removed nothing and struggled forever. This takes no time at all and makes it an easy job if you have small hands like me. As for the bleeding technique, that's a little too "official" for me. I just leave my radiator reservoir cap off and let it get to about 90c so it doesn't boil but also circulates that air out of there. Maybe if your water pump is really weak you'd have some issues pushing the air out, but I've Never had any issues doing this with my 06 focus and my previous 2 cars (99 corolla and 04 audi a4).

I just tackled this job on my '08 Focus 2.0 Duratec. Unfortunately I live in New England and one of the thermostat bolts was severely rusted and wouldn't come out (even with a bolt extractor socket). I ended up having to remove the intake manifold so I could weld a nut onto the stripped Bolt to remove it. I give kudos to anyone able to do this job. There is very limited space to work especially if you have large hands like me..

At least they finally designed a thermostat that generally fails open rather than closed

@arthuroalcorte123

3 жыл бұрын

Ain't that the truth!

@rolandohiebert2144

3 ай бұрын

Mine is sticking closed on my 2.0 focus so the engine literally boils the water without the temp gauge going up

@jesusramos5204

2 ай бұрын

What causes the water to back flow through the expansion tank.

@jesusramos5204

2 ай бұрын

2.0 engine 2014 focus

I picked up the AirLift off Amazon, and got the $70 Amazon Visa Card discount.... so it was 1/2 off.... We used it on my 08 Escape this past weekend and it worked great. I have a couple of these Escapes, so I think it's a well worth tool. Thanks for the advice via your Video. You are my 1st stop for For Escape service!

You are the best Tech and best repair videos/info on KZread, thank-you.

Just replaced the thermostat in my wife's 2009 Ford Focus earlier this week using this video. I used a vacuum refill tool I got from Harbor Freight once done but didn't clamp off the overflow tank when applying the vacuum yet everything seems to be working alright. So far there's no overheating and the heater is blowing great!

1:16 "Be a little smarter than the car" Great words of wisdom right there.

I just did this on my 08 and it went pretty well using this method. Had a few hiccups along the way but over all it went exactly as described.

@FloridaSunMitochondria

9 ай бұрын

What were your hiccups so others can learn from them?

As always, excellent work on the video; the detail work is beyond reproach. Replaced thermostat assembly with new hoses and clamps today on a 2008 Focus. Did not remove the fan. Time about 4.5 hours total; tough job for me. If I do another one I believe that the time saved by removing the steering pump would be better than my effort today. But as always and again, thanks truly for your presentations.

Very good video. Tons of tips and tricks. No need to remove the power steering pump. Thank you!

I just did this on my 2007 Ford Focus. Some notes: Would recommend a magnetic-type socket for removing and replacing the thermostat bolts. A long jawed and angled needle nose pliers works good for getting the clamps off. The 2007 2.0 Focus doesn't have the hex drain cock and nipple shown here. It only has a slotted plastic plug you loosen to drain the radiator. When removing the shield behind the front bumper and under the radiator, you may want to already have the plastic push pins available. Because it's often impossible to remove them without breakage. Cooling fan electrical connectors on this car are on the top left side (two plugs). Also on this car the cooling fan assembly sits in tabs on the sides and doesn't use bolts. Will need a screwdriver to slightly open the locking tabs on the top. Lift up slightly and then lower. Disconnect the pressure switch connector from the power steering pump, that interferes with access to the thermostat bolts. On my 2007 Focus, the clamp on the short bypass hose that is removed on this video, on my car it didn't have any "ears" to grasp. So I had to unbolt the thermostat (again--a magnetic socket makes this easier), pull the thermostat away from the engine, and then take off the clamp that's closest to the thermostat. On my 2007 Ford Focus, didn't need to use any special procedures to refill the system. The Ford Service Manual just says to fill the recovery reservoir to 1 inch over the "full" mark, and then run the engine until the thermostat opens. And yes---it's a real bear to replace!

That 2.0L is the first Ford engine that I have seen in a VERY LONG TIME that has a coolant fill neck attached directly to the radiator and a true overflow tank. Every other Ford I have encountered (admittedly not that many) has a pressurized remote coolant tank (you called it a de-gas bottle on the second car). I have never had to use a vacuum fill tool on an engine with a pressurized remote coolant tank. Fill it up, run the engine up to operating temp, top off the coolant and your done. Best practice is to check the level after a full drive cool down cycle.

Hey! I just got a P0128 on my 09 Focus. I've had my car since brand new, and this is the first time it occurred.

Best an most complete vid on this I have seen … will be doing one in several days myself … repair shop wants $400.00 . Thanks loads !!!!

Just did this on my daughter's '09 Fusion 2.3L. Things to note about it: Before pulling the cooling fan up & out, there is a hose support at the bottom that wraps almost all-around the radiator hose... you'll need to push the hose out of it. Second, to help guide your extension and 8mm socket, use a light for the top left bolt which can be seen thru the IM runners. The top-right bolt, look from the PS pump side, but to see the bottom-right, I used a mirror. For the small bypass hose on our car, there was no extension hose near the t-stat housing like on the car in this video, so I also just left it clamped to the housing like the main radiator hose. Once the t-stat housing is unbolted, I had to disconnect the connector at the compressor clutch, which allowed me to manipulate the housing and attached hoses between the a/c lines. At first, you may think it's not possible to get it through there, but if you tilt it a certain way, it actually comes thru easily. Doing so, makes it easy to swap out the t-stat/housing assembly right there at the car. Unlike the car in this video, on my Fusion there were other hoses branching from the main hose, so to me it was more trouble to try to get it to the bench. I easily put the clamps back on hoses where they were. Also, just before refilling the coolant, don't be afraid to loosen the plastic bleed valve cap several turns or even to take it off for that matter. My Haynes manual incorrectly said to only loosen it 1/4 turn but that wasn't nearly enough to allow any air to escape. However, running the engine afterward for 10 minutes at 2500 rpm did seem to do the job. I only had to top the reservoir off a little bit after I drove it about 3 miles afterward.

@AustinWilhite

4 жыл бұрын

I fought with getting the fan out of my 2008 Mercury Milan 2.3L for 45 minute before giving up on it. I removed the bottom hose support from the hose, but still couldn't wrestle it out of there. I'm not sure how you managed to do it. I opted instead to remove the power steering pump for access to the thermostat bolts.

Thank you so much! The video I saw before this one was a nightmare! Guy took off power steering pump reservoir and a bunch of other stuff. Much easier, weekend project

The Mazda FSM says that in order to bleed the air out you can hold the RPMs at roughly 3000 for 30 seconds, rest, then repeat. This worked quite well for me. You cool with that Brian? I don't think that many DIYers will have that vacuum bleeder assembly. Thanks!

@FordTechMakuloco

7 жыл бұрын

Yes I have a video on that procedure, but I only use that to remove the last bit of air from the cooling system Here-kzread.info/dash/bejne/ZpufltqbacS1l6g.html

@baxrok2.

7 жыл бұрын

Excellent. Thanks!

@ReclusiveMountainMan

7 жыл бұрын

I recently changed coolant on my 2010 Fusion. Luckily I was monitoring the temp after refilling. The temp gauge went into the red range. I shut the engine down immediately. Everything was okay, but those pesky air pockets are dangerous if you aren't observing things. I'll invest $100 in a vacuum bleeder system. I bought the brake vacuum bleeder you recommended and love it!

Excellent video and workmanship as always Brian. This video interested me since I have the 2015 2.0 and have complained to Ford service dept about how slow it is to create heat in the dead of winter. Often times on those sub zero days its 15 miles of highway driving before I can feel heat at my feet. Then I jump in my work Sprinter diesel and have abundant heat within 2 miles ... ya can't make it up. I'm sure it just a matter of time before I'm doing this procedure.

Thank You‼️This Channel is a God Send!

Excellent video. Articulated the reassembly perfectly. I appreciate all the good work! keep it up!

Ford sure likes to pack that engine bay tight, don't they Brian? I recently acquired a 1996 Mercury Mystique with the 2.0L Zetec engine. 243k miles and purrs like new. I know the owner replaced all the coolant hoses and thermostat housing before I got it...the hoses burst one by one, and also the water pump seized up at 230k miles. So several overheating episodes but engine seems to be OK. It definitely has a lot of specialty hoses and pipes and clamps that are a PITA to get to. Wiring insulation under the hood is a little crumbly too lol. But the 5-speed drives so nice and looks cool too so I'm keeping it! :)

@FordTechMakuloco

7 жыл бұрын

The ZETEC was one rusty nightmare!

@PineHollowAutoDiagnostics

7 жыл бұрын

The engine or the car? The one I got is pretty mint for a Central PA vehicle...and the oil pan seeps around the gasket so there is some undercoating on the belly as well haha

Great video. Idk if some fusions are little different but it was a lot easier for me to take hoses off and slide right back on. Didn’t take off fan shroud. Changed water pump also. Thank you for the video.

I was so sir-prized you didn't replace the hoses while it was out. A few bucks now saves a lot of work later. Also, a very light swipe of silicon grease on the surface of the housing connector or inside of the hose makes a nice seal and keeps it softer and easier to remove later.

My '02 Explorer 4.6l 2V had the same symptom, didn't heat up fully. But I'll admit teh Thermostat replacement was several times easier. The O-rings do a great job of sealing it.

Brian you make it look easy, thanks. P.S. The F one sissy is still running!

Thank you very much, I just changed mine this weekend, 2008 Ford Focus SE, was not as bad as I thought. I tested the old thermostat in boiling water, it did not open so it was bad. After putting on the new one (no sensor, $23 Advance Auto) the car does not over heat at all anymore! It was overheating all the sudden after only 5-10 mins. of driving, on not even a hot day, lik 78 degrees.

@tn7198

5 жыл бұрын

Exact same symptoms here. I HATE overheating even for a moment. I have seen solid cars with low miles turn to DEBT for the owners due to this (new engine). Remember when you shut off, residual heat will cause temp to rise for a few more minutes, and of course your imagination runs wild what's happening inside the engine. My wife was amazed that we use thermostats at all when I explained how they work and what can go wrong. She has a very fair point!

Most direct installation I've seen... Appreciate it.

Amazing video on this replacement, thank you good sir!

Some thermostats come with a sensor and the one you recommend is without one. I have Ford Focus 2008 SES, how do I know if I need the thermostat with sensor or without? Thanks

Just did this repair on my 06 Escape Hybrid and it wasnt too bad. Removed the belt and tensioner which made so much more access to the housing. Took me about 2 hours to do.

@FordTechMakuloco

7 жыл бұрын

Yes but that is a bit easier with no power steering pump in the way.

@WillsGarage91

7 жыл бұрын

True..

@thomasrossi31

5 жыл бұрын

What is the best procedure for bleeding the system on a hybrid?

Thanks for a great tutorial. I own a 2015 Jaguar XF and yes wrote Jaguar since the 2.0 shares the same engine as the Ford edge , focus, fusion and Lincoln. I have been looking on KZread and I found your video on the same engine on how. I know the XF has the rear wheel drive so I may not have to disassemble the radiator bit it is still a challenge to get to. Thanks for a great video

I have a ranger with the 2.3L. Same thermostat. Just popped the p0128 code. Will be changing it soon.

Another briliant Ford Design!

This guy is the best.

Hi, so I have a 2010mercury mariner 2.5 liter with a heater problem, I had it fixed a few months ago and now it doesn’t work again. I think you're videos will work for my mercury pretty much since it's just a ford with a different name right. Thanks again

Serious question: So there is no way to “burp” or remove the air from the coolant system without using one of those special air pressure bleeders?? That kind of limits any DIYer from doing a thermostat change.

Thanks for the video. We just bought a really nice 2011 escape last year. That thermostat doesn't look that bad, a pain but not the worst. My worst t-stat was a 95 lumina with 3.1, the housing was covered by an exhaust pipe. The bolts were rusty and you can guess how bad it got. God I hated that car!

2011 Focus. Thing never reaches operating temp unless I let it idle in park for at least 30 min. Going 80mph on the highway in 60 degree weather though? Thing doesn't even get up to 1/4. No CEL. Just sulfur smell from the CAT burning excess fuel. Considering my wife never says anything and I only check the car periodically, it's been rather reliable at 175k. I recently did the gasket on the top of the engine in an attempt to change the overhead temp sensor... oil all over the plugs and it still kept chugging. At least the wife was good about oil changes as the engine looks pristine inside, no sludge and the lobes look great. The 2.0 really is a strong and reliable engine minus a couple dumb quirks. Mazda really made a solid engine. I can see why Ford has continued to use it and refine it for decades now.

Got a 07 focus 2,0 duramax. Getting a 1289 code. Any advice would be welcome. I watch all your vids before doing a repair, and also have a 01 f150 with 4.6 . Ford does make you LOCO!

Excellent explanatory video so much I thought I knew. Thank you very much for the help

this was a BOMB video it was well put together -thanks for posting saved me $500.00.on my 08 Ford Focus showing code P0125!!!!!! GREAT EXPLANATION....

@pslay9324

Жыл бұрын

OMG !! I found my post well my sister has a 2009 and 4 years later her car thermostat needed to be replaced.

Wasnt sure I was going to learn much from you 1st few moments had no idea where you were on that engine BUT I NEVER used a magnetic tool to thread a bolt in that my fat hands cant reach thank you

Thank you sir....everything you did in the video was perfect....you were spot on ....made a hard job easy .....again Thank you.......Terry

The filling system you have I might have to get one mo mess trying to bleed it with the funnel I have

When I did one the other day I just removed the belt and moved the power steering out of the way. And I had access to the thermostat. A little tight but it fine.

@Jota-rc8yq

3 жыл бұрын

How do you seal the thermostat, do you use silicone or some type of gasket?

This is a well made video that explains it all. Thank you!

This was super helpful- thank you!

I had this code pop up in cold January. I took the car to the dealer to replace thermostat and flush/replace the coolant. Everything was working fine afterwards. Few months later, (October-chilly weather) the code has come back. Any suggestions?

@mistersnapon

Жыл бұрын

I replaced 3 genuine ford thermostats...2 cylinder head temp sensors and still get the code!!!! Whats next?

@MrGgarcia7298

Жыл бұрын

@@mistersnapon my scan tool also says it could be a bad Intake Air Temperature sensor. In the case of the panther platform, this sensor is incorporated into the Mass Airflow Sensor. I will have to replace the MAF if this other thermostat doesn't fix the code. Beyond this, I've no clue.

@mistersnapon

Жыл бұрын

@@MrGgarcia7298 Replaced that also....took to ford dealer and after $500 later it still does it!!! Also air filter!!! $$$$

@mistersnapon

Жыл бұрын

@@MrGgarcia7298 I replaced that too!

My thermostat failed shut on my '07 Focus SE at the 11 year point. When they were repairing it they broke the power steering reservoir and thus I had to have that replaced. I wish I had seen this video before it happened.

I had the code on my 2009 2.3 Ford Fusion. The thermostat was definitely the culprit. I am not getting an overheat condition and I am getting heat in the cabin;however there is a slight slushing sound at the beginning upon starting the car. That is an indication of air in the system correct? Well I attempted the vacuum method-pulled about -26. Filling it up was easy but once I started it no heat in the cabin and driving it around it started to overheat. I purged it through the service purge valve and it seemed like some air made it’s way out, but I am back to hearing the slushing sound when first starting the vehicle but everything works: heat in the cabin and no overheating. I am curious what the long term effect is if left the way it is now? I will attempt the vacuum tomorrow once again and hopefully it gets rid of the slushing sound, almost sounds like ocean waves 🌊

FTM Thanks for another beautifully shot video!

I don't have an air compressor. Is there a way to do this with a vacuum pump?

@NilsJakobson

5 жыл бұрын

That vacuum procedure is completely useless. Just put the coolant in, let the engine run with the cap off, put the heater on max heat and revv the engine abit now and then until you feel that it starts blowing warm. Then shut it off top off the coolant to the level and youre good.

Nice! Keep it up!

Thank you for the video. They definitely do help us out. I would have never known to bleed the system after replacing the housing.

I did this two years ago on my 2010 fusion, if you take the air box out you can reach the rad drain from the top, and since it has electric ps I could reach the thermostat from the top no problem, I replaced the factory clamps with screw clamps, no leaks working just fine.

@bobmcl2406

4 жыл бұрын

Actually the original spring clamps are superior to the screw clamps. Spring clamps allow for expansion and contraction cycles, while retaining tension. Screw clamps eventually loosen. I also replaced a Ford spring clamps with a screw clamps on a lower rad hose, and wound up with a leak a while later. Now I grab good condition spring clamps whenever I am at the wreckers.

Brian - Awesome Video Bruddah. I learn so much from watching and re-watching your videos. Thanks Bruddah!! Btw, where is the video link you mentioned at 18:45? (procedure to push air out of the heater core and engine)

@leo28a

7 жыл бұрын

Hawaiian F150 same question Where's the link to that vid. Brian

@FordTechMakuloco

7 жыл бұрын

I had to run out to a few mobile repair jobs right after posting but all the links have been updated at the top of the comments and in the video description as always.

Does this engine have a cylinder head temperature sensor and a engine coolant temperature sensor or r they the same

I know this is an old video but had some questions.i have a 2011 fusion with the 2.5. Manual says specialty green anti freeze. Ford said it's been replaced with yellow. I don't think I should mix these. Also I bought the vaccum fill tool. My car doesn't have a radiator cap. Can this tool be used on the degass tank or can this tool not be used on this car?

Love the Air Lift been using that for many many years.

I have a 2012 focus w/2.0 and its consuming coolant. The car only has 70,000 miles on it. No coolant mixing with engine oil. Is this common?

Excellent video

I just changed it on 2006 escape hybrid, pain in the but, the radiator drain is on driver side. To bad I did not had the tool to remove the air from the system. The 3 bolts from the termostat were the most difficult to remove and after to install. If you do not have the proper tools, extensions etc. Is better to see a shop to do it for you. Took me 3 hours to replace it.

@againsttyranny2149

2 жыл бұрын

@Ciprian Taune I have similar truck the heater is not coming on. Was that the reason for replacing the thermostat? Because it stuck open.

Question: can you bleed the air by using bleeder valve? I don't have the vacuum set up. I used bleeder valve until all the air was gone and only fluid was coming out in a steady stream.

I don't know how he did it! i have an 06 focus(2nd generation focus), same engine as the one in the video(3rd generation focus)2.0 duratech, and I had to remove the power steering pump. fordtechmakloco did a wonderful job. before you condemn the thermostat, check your cylinder head temperature sensor. mine i had to replace before.

Great VIDEO I have a 2.3l in a 2011 Ranger that seems to be running cool (175deg.). What would be the proper operating temperature for this engine. I've found a RT1193 and a RT1194 thermostat but the don't give any temperature settings. Thanks

Very well put together video,its strange for me to watch a video on car repair,I come from the day when parts counters had parts books 5 ft wide

I have a 2016 and when you start the car up and use the heat it won't go past a quarter on the temp gauge. Heat keeps the engine cool. Suspecting thermostat. Replacing it today.

How do you know if the thermostat is the Problem ?

@FordTechMakloco could you please do a video on pinging/knock on these engines? i have an 06 focus that the engine knock in the summer months. especially audiable when you're stopped at a street going uphill and want to initate speed from a stand still!! i changed the knock sensor, spark lugs, used premium gas, to no avail!

@mrau92me

6 жыл бұрын

If you're talking about a kind of a "grunt" sound when you first accelerate, I think it might be related to some butterfly valves in the intake manifold that are supposed to cause intake air turbulence at lower RPMs. The flaps are plastic and the rod that actuates them is metal. I think the metal rounds out the plastic a bit and then it begins to rattle, especially when accelerating from a stand still.

Great Channel, Love my Ford

Brian I replaced both the thermostat and the ECT sensor on my 2.3L Focus and cleared the P0128 code but the code still keeps coming back. I used Motorcraft parts. The coolant level is good. What now?

@Mr2004MCSS

2 жыл бұрын

Did you ever figure out what the problem was with yours? My fiancé's son's 2008 Ford Focus had this code pop up last year and we had a shop replace the thermostat with a Motorcraft replacement. The CEL came back on the other day and it was the PO128 again. I can't imagine the thermostat is bad again so it may be the ECT sensor or the wiring to it. I'm not even sure where the ECT sensor is on this car which is the 2.0.

@LA_Commander

2 жыл бұрын

@@Mr2004MCSS I had replaced both parts and still get the code popping back up. I even took the car to the dealer for a complete refresh and update of the PCM and that still didn't work. Don't know what else to do now. You can try to replace the ECT sensor, it MIGHT fix the problem. It actually doesn't have an engine coolant temperature sensor like many cars, it has a cylinder head temperature sensor (CHTS). FordTechMakuloco has a video just on this subject. It is located on top of the motor between the 2nd and 3rd coil packs. You need a 19mm deep socket to remove and replace the sensor. You will also need a new pigtail to splice into the wiring. Please watch FordTechMakuloco's video on this very thing.

@Mr2004MCSS

2 жыл бұрын

@@LA_Commander Thanks for the additional information. I remember that sensor from when I replaced the valve cover gasket on it. Next time he is here I will take a look at the connector and wiring to the sensor and see if I see anything obvious.

I have a 2005 Ford Focus ST with the 2.3L engine, and I will be undertaking the same repair/replacement this weekend. I am having trouble finding the bleeder nipple on my engine. Do you have a diagram or picture of where it is? I looked where you showed in the video with no luck.

Very informative. Thank you.

The early ford focus 2000 to 2004, the thermostat housings were prone to leaking. The lip that holds the rubber O ring in place will corrode away causing the O ring to collapse in on itself causing the leak. The permanent fix is to install a thermostat housing from a Ford contour, same diameter but different design.

wouldn't you just get a new hose since you got it off anyways? extra expenses for sure but new for the new part?

@jessev2197

7 жыл бұрын

I always use a new hose b/c there is no more rubber compression to seal. Just asking for a leak that's cheap to prevent.

@FordTechMakuloco

7 жыл бұрын

Never a problem here.

@DeRochaJ

5 жыл бұрын

The rubber hoses today are well made. Back in the day when they were not that stout it was wise to change them.

@vice7943

4 жыл бұрын

Great video. I only would disagree with resetting the clamps in the same place. As seen in the vid, the clamps will continue to dig deeper into the hose causing damage...mostly at the pinch-point. If you slightly rotate their alignment upon replacement, the clamps have more "meat" to eat into and will hold beautifully. Also a little silicone glue helps prevent any leaks. Who wants to do a job like this twice? Lol. Great video though. Thanks!

Was that a scotty kilmer grunt at 7:50 ?

@FordTechMakuloco

7 жыл бұрын

+ReclusiveMountainMan Maybe!

@jamess4351

6 жыл бұрын

ReclusiveMountainMan Rev up yer engines! !! 😂 uuh

@DeRochaJ

5 жыл бұрын

LOL -> @@jamess4351

How do I remove those 2 connectors, I've tried for about 4 hours now and I'm afraid I will break them if I pull harder

any idea why my focus 2.0 '13 is pissing out coolant from the middle of the car? there appears to be hoses that run underneath possibly damaged Im not sure. Why is coolant running back there?

My 2013 Fusion Titanium (93k miles) is leaking coolant. Seems like from the thermostat housing area. I'm guessing the gasket wore out. Can I just replace the gasket (part # 3M4Z8255A) or should I replace the whole thermostat housing with a new thermostat? Thank you

Awesome well laid out video👌🏻

@FordTechMakuloco

7 жыл бұрын

+Darwin W Thanks!

@darwindropmazda

7 жыл бұрын

FordTechMakuloco Huge fan of your vids very good consistent content!

@FordTechMakuloco Love you videos, they help me alot!!! was curoius what kind of camera do you use when filming?

Checking Thermostat without taking the thermostat out was, one hose cool & then hot when open or look in radiator & when open, coolant moves across because Water Pump

i have a 1.6 do you know if the alternator needs to be removed to access the thermostat

I am loosing coolant kind of slowly cant find a leak someone is telling me its thermostat and that because its sticking my coolant is coming out overflow this doesnt really sound right to me.. thoughts?

@rinr7052

4 жыл бұрын

BRWfilms I was told the same thing! Coolant leak. Need thermostat replacement. I’m looking into it now.

Any idea what a hissing sound coming from the driver side of the engine is, plus I see bubbles. I thought it was the thermostat but I see that the thermostat is on the opposite side .It does this specially on Summer. I have a 2010 Ford Focus BTW-Thanks

Where is the coolant temperature sensor located? 2006 mercury milan 2.3! At idle my temperature gauge keeps shooting to cold. Only thing I can think of is the sensor. Just change thermostat about a month ago

Very helpful! Thanks!

what motor does the 2005 zx4 Ford Focus have in it I know it's a 2.0 but it has been an excellent motor we have three hundred two thousand miles on it and it's still going strong

@KB-bh9hp

7 жыл бұрын

Big Mike FAM Prob a series of engines called duratec they have a reputation for being extremely reliable expect similar milage from the 3.5 in my explorer at least.

@atx-cvpi_99

4 жыл бұрын

Kevin B The 3.5 and 3.7 transversely mounted Duratec is the least reliable Duratec other than the Duratec 3.0 in the 4th gen Taurus and Sable.

Bought the airlift have to do daughters focus but no radiator fill tube do you put vacuum on overfill bottle?

@FordTechMakloco Thanks for this video. My question is if I am doing a coolant flush on the exact same engine do I need to use the vacuum tool you are showing? Thanks in advance.

Ok i changed the Thermastat and bleed the line its not over heating but my engine lite is still on . how do i get it to go off

@FordTechMakuloco

6 жыл бұрын

You must disconnect the battery it is not self clearing.

@DeRochaJ

5 жыл бұрын

The CEL may take several drive cycles/days to clear on it's own. For immediate results you can use a OB2 reader to read and clear the codes or disconnect the battery for a few minutes.

Dumb question, but how do I know if the thermostat is the issue or the temperature gauge in the dash?

Please tell me something, there is an o-ring inside the thermostat, how to place it in its place? not talking about the around seal, but about the circle ring

so i need to replace my thermostat on my ford edge 2.0, i cant just replace the thermostat, put new coolant in there and then start the car ?

I just bought a thermostat just to have one in-stock at the house! ;)

If the car has 110,000 miles, wouldn't it be good to replace the hoses?

My 2008 Escape with 3.0 L engine had thermostat that sticked closed, not open.