I bought a cheap foam cannon from amazon as well. I've used it over 100 times already and it still works perfectly fine. In reality you only need 1-2 oz of soap and about a quarter of the bottle filled with water and I got some crazy foam. Have used this technique in all of the cars I've detailed and even when doing larger vehicles

@djeremie2153

5 жыл бұрын

Like mentioned above. You only need about 1/2 the bottle with water. I use CG mr pink and get great results with similar setup

@johnnydavies927

5 жыл бұрын

Dose it fit any jet washer

@matthewjackson9615

4 жыл бұрын

And the foam does what ? Looks cool , so what the hey.

@brandonalan1513

4 жыл бұрын

Matthew Jackson loosens stuck on debris so when you rinse it, it washes away and leaves your car squeaky clean

@SOKPUPPY

4 жыл бұрын

Does that mean you don't have to scrub your car? For light dirt obviously, not caked or baked on stuff. Or does it break that down too?😁

Used the same 1.1mm orifice mod on my amazon foam cannon. And CG Honeydew Snowfoam, awesome results.

Thanks for showing the mod. I kept hearing people talk about this mod but I had no idea what they were talking about. Now I do.

Good video. I have same foam cannon and was considering buying a more expensive one. But I'll try this mod first.

Ordered this setup thanks to you. Works great 🤟🏻

Other than getting the hose connector turned around (watch out for that one), the machine is simple to put together and use kzread.infoUgkxfQauTxLT0JLSvqkq10rD79TU4k0Vz8zP . And very nice, too. I'm surprised at the power-it's more than we'll ever need, and we've not even used the most powerful setting yet.I've cleaned off a dirty concrete porch to get it ready for sealing, started to clean siding, and I know this pressure washer will be terrific for cleaning tools this fall.The only issue we had is we had turned around the hose connector, and it leaked. Once it was on correctly, though, we had no problems with the connection. Just remember that the end with the green knob goes towards the hose. It's obvious now what we did wrong, but not necessarily obvious at the time.

Thanks for also showing the orifice swap install itself. Plus citing 16 for wrench size.

I typically use 3 oz of soap and fill up half the bottle. No real need to fill whole bottle up and I get really good results. I also have same pressure washer but bought a chemical guys foam cannon and then upgraded to that smaller piece.

Loving the intro! 🙌🙌🥰🥰

2:56 when you start dating a Latina

@user-fb5zk3bd7i

5 жыл бұрын

alex nasiadka 😂😂

@brad_neal

5 жыл бұрын

Pasty white here... I married one. I call her my lovely Latina! Damn!!

@alexnasiadka5140

5 жыл бұрын

Brad Neal lucky man!! Lol

@mrsmith7493

4 жыл бұрын

Funny but true

@Skyoneder

4 жыл бұрын

😂 nice

Thanks to this video, just pulled the trigger on this orifice, the Amazon cannon, and a SunJoe SPX4000. Thank you for the top quality intro to a killer budget car wash setup, Blake! Looking forward to using it on my '90 325i sedan and '07 E92.

@BlakesGarage

5 жыл бұрын

Sweet!!! It will make your life so easy

@BigLou19

Жыл бұрын

Will that set up work on a electric Green works 2000psi?

If you swapped in a 1.1 then you most likely had a 1.25 installed on the first test. The 1.1 orifice is made for lower psi washers so it doesn’t get quite as much water

@92greensho

4 жыл бұрын

YEP ^

@nahuel2222

4 жыл бұрын

My washer is 70PSI with a max of 105PSI, should i use 1.25 or 1.1 ?

@Audiophilifix

4 жыл бұрын

@@nahuel2222 1.1

@Taylexwow

3 жыл бұрын

@@nahuel2222 You don't have a pressure washer......you have a garden hose.....the water system from my city is higher pressure than that unless you are using some different system of pressure measurement.

@tebz2145

2 жыл бұрын

@@Taylexwow he prob ment bar not psi

Dude! YES, thats a super cheap fix that makes it so much better. Also I really like the two B-Roll shots you 3:02 Keep up the great work!

@claudeloi

3 жыл бұрын

Still too expensive for me. Read my comment. Got my done for zero dollar.

Not even through the video yet, just needed to stop and thumb up the use of ‘No Quarter’ - dope!

@BlakesGarage

5 жыл бұрын

Thanks buddy

The 1.1mm orifice clogged within 30 seconds for me (using Stanley 2150psi 1.4gpm electric pressure washer). The stock orifice works flawlessly.

Have the same pressure washer. Got pretty good results in foam with meguires gold class. Switched to chemical guys stuff. Not as much foam so I'm eager to try this

Thanks for this info. I'm going out tomorrow and get the Ryobi 1,900 PSI electric sprayer.

Just started checkin out these foam cannons after 5 vids ,read the directions pressure and gpm determine orifice size

@AB-80X

Жыл бұрын

Yup. The manufactures of pressure washers must really love these "experts" giving advice. Why mess with a good thing when people are shortening the life of their pressure washers lol. That said, many of these small garbage pressure washers do work and need a 1.1mm orifice. But still, people should really look in a table to find what they actually need.

I realize I'm a bit late here. Been out sailing the seas on Navy Aircraft Carriers. Retired now and got more ME-Time. You sold me on the Orifice replacement. Great Video!

@Aswaguespack

3 жыл бұрын

Thank you for your Service to our Country in defense of our Freedoms.

Bro I just got this foam cannon but at the time you connected to the pressure washer it doesnt attach kinda well, it leaks water from the quick connector. Did you use some white tape to seal it?

i just ordered the 1.1 orfice for mine Thank you

Excellent Mod. Thanks.

Perfect solution to my issue. Thx for the video. 💯👊

@BlakesGarage

3 жыл бұрын

No problem 👍🏼👍🏼

Blake recommend to exchange the orifice universal 1.1m screw costing about over 7.00 + shipping on Amazon. I am frugal so I went get me a short piece of Nichrome wire, cut a short lenght then insert into the orifice bent the wire to a 90 so it mate flat into the grove slot of the screw and that is it. The new reduce hole diameter will do the job. My way to save money and get result.

Awesome thanx just ordered

Can you provide a link to an adaptor to make the lance wand quick connect fit the soap cannons? The sun joe spx3000 doesn’t fit standard foam cannon connections.

Great video man! I just ordered this!

Adjust your spray pattern. It’s to wide. You’re putting half the foam on the ground.

I’m no chemist, but the foam thickness doesn’t mean better cleaning power. The soap also has something to do. I did that mod. Yes the foam is thicker, but it doesn’t remove more dirt than before. Thanks for the video. Wash your hat or better yet, throw it out.

@tuninggamer

3 ай бұрын

I think the idea is that thicker foam is less runny and liquid and thus stays longer in place to work its magic on the dirt. But I think you’re right in saying that the type of soap used is important too

hi does this work for MATCC Foam Cannon Adjustable Snow Foam Lance for SPX Series Pressure Washer?

Cleanest passenger fender after that video was done lol

Now this is a strong beard 💪

I like this soap and have the same foam cannon. You may need to adjust the + and - on the top...I get thicker foam than this with mine consistently. I have a ryobi pressure washer so nothing much different in that realm.

@every_thing_wood1251

Жыл бұрын

I have the ryobi 1800psi and i cant get good foam for the life of me

I would put the hot water in the cannon first and then add the snow foam soap. Great video! I just got me a 1.1 and can’t wait to try it out. You have to get a short gun it is SO much easier!!

@AB-80X

Жыл бұрын

Here's a question. What do you think that happens when all that cold water flowing though that lance hits that small amount of warm water? Some very thick soaps will dilute a bit better in hot water, but other than that, it doesn't do anything.

@jh.f30

4 ай бұрын

Helps the soap mix with the water​@@AB-80X

I noticed adding water first is better then your soap but any recommendations on when i use my foam cannon it comes out to strong like my pressure washer is on full blast

Hey anyone know a cost effective source for the replacement bottles? snapped mine, company cites their $20 plastic bottle is back ordered. Has to be a standard size available?

Where can I find the stainless steel piece?

Thanks for the tip. Just ordered one, hopefully I see a change. I pay way to much for my foam cannon soap not to get the most out of it.

@Coelacanth97

4 жыл бұрын

I bought this 1.1mm oriface for an MATCC foam cannon and when I removed the original oriface and compared it to the "upgrade" part, the hole sizes looked identical.

@jiovannymadrigal4335

3 жыл бұрын

@@Coelacanth97 yeah I noticed it was the same size as well. I think there was no point in buying this.

I'm trying to focus my eyes on the foam cannon but it keeps on focused with the beammer lol

Nice video 👍🏼

I use my foam cannon with my Karcher eco-although it's not set on the eco-mode it doesn't do a bad job took it to my buddy's place changed the end put it on his petrol pressure washer wow what a difference with the form so it also has to do with the amount of pressure coming through Took it back to mine change the end again put it on my Karcher not to good .. took it back to his did the same thing wow

I am waiting for the bosch easy aquatak 120bar to be delivered....and i have the meguiar's snow foam cannon .... !!! Will i have a good result for car wash??

after you foam it what do you do next

Thanks! Hope it works.

Check out nerta active diamond foam, find it quit good. rinse all the dirts out with about 5% mixture.. My fav prewash foam

OK I got a bear force Lance cannon 😳 how can I hook it up to my garden hose??

do you know the thread size of the quick fitting? is it 14mm??

Do you need to put a new O-ring on the new orifice?

Badass video bro

Did the one you removed have an o ring on it?

When I use my phone Cannon the pressure washer stop and go stop and go and it's not coming out at an angle and I did the modification I'm new to this if someone help me?

I appreciate this video, along with your others, but I'm not sure why the fluffier foam is better. I get that it LOOKS better, but I can't think of a way it gets your car cleaner. It seems like the mod just increases the amount of air that gets mixed into the soap. If so, how does that clean better, at least after a certain minimal point? It reminds me of how the shaving cream companies used to sell their shaving foam - advertising how thick it lathered. It took me years to realize how much better it was to use a little soapy water and a brush.

Why y’all hating it’s clearly thicker than before. He didn’t say “this is the thickest foam ever” no he was just stating that it was thicker than before which it definitely was

Just bought one, same day shipping hopefully it will get here early during the day so i can see if it makes any difference with my 1600 psi electric power washer

@BlakesGarage

5 жыл бұрын

Awesome hope you find thicker foam after the install.

I have the same Foam Cannon but I feel that it uses a lot of shampoo, I have to fill the bottle two and three times to be able to foam the entire car...... Any suggestions???

Thank you! I was about to get the exact same washer only the model w out the hose reel. Have you tried the other soaps? Great video

@BlakesGarage

4 жыл бұрын

I haven’t. Mostly because I’ve yet to run out of the gallon I purchased about two years ago.

@CTRadventures

4 жыл бұрын

@@BlakesGarage thanks for the update ! I put in my order, I'll let you know!!

Where did you get that new fitting?

What a cool video! Did not even think you could hack it haha I will copy your idea! Thanks for the tip.

Thanks for the video, I will have to go this route. I have a chemical brothers store not far from me so was wondering if I should buy one of their guns or like you did just a cheap one online.

Your car was already clean ;-)

whats your ride ? make and model ?? Nice

holds in same place for 10 seconds. oh yeah waaay thiccer

@11Forty6

5 жыл бұрын

Naz Sen I thought that too.

@BlakesGarage

5 жыл бұрын

It’s the way the foam builds, with the other orifice the foam is much less fluffy, more watery, so it doesn’t build up just leaks off the car.

@PoradoWeara

5 жыл бұрын

Yeh thought same

@JyroOne

5 жыл бұрын

@@BlakesGarage Its supposed to flash foam and run pulling dirt off with it. Thicker foam doesnt mean cleaner car either. Dawn Platinum foams way better than that private labeled Chemical Guys garbage and probably cleans better too. I have some truly bad ass soap if you ever want a real difference. Check Blair Ceramics website if you want info.

@Tuvzii

5 жыл бұрын

@@JyroOne dawn also strips off waxes and other sealants, you would only use that if you were doing a full detail to get all product off the paint

I noticed a lot of the 1.1 mm brass orifices sold on Amazon are also including a stainless steel mesh filter many call the “foam maker”… I wonder how much of a difference replacing that mesh filter makes?

@NickVetter

2 жыл бұрын

I noticed no difference between the filter that it comes with and the replacement. They look the same. It is nice in case it gets completely clogged.

I notice when you first start foaming with either orafice, the spray pattern is crazy wide, then you cut the video and then the spray is much narrower. What did you do?

@BlakesGarage

5 жыл бұрын

Just spun the tip to dial in the spray pattern to what makes the best foam.

oh hell yeah!!!! awesome. Positive Flow.

Intro was Sick👍🏾

@BlakesGarage

5 жыл бұрын

Thanks man!!

Nice it does foam up more. Honey dew sucks I don't like it. I use maxi suds and it doesn't up good I can just imagine what it will do one I change that part.

Bilt-Hamber Auto-Foam works a treat....try it.

@AkAsCoTTii3

5 жыл бұрын

James Butler Quality products

@philb1378

5 жыл бұрын

I concur!

@whitewalker9622

5 жыл бұрын

Love it!!!

@AK-ck1bz

5 жыл бұрын

I really wish I could get that in the states

Problems with all the links in the description that I tried. I didn't try them all. Any tips?

Hey are any of the sun Joe pressure washers good? I am looking at the smaller one right now and the one from harbor freight. Or is it better to just get the newer version of this sun joe in your opinion? Don't want anything too big since I'm military and I'm moving around a lot.

@AB-80X

Жыл бұрын

No they are not.

You can put a screen in it as well. Works better. Gose in the front.

That Zeppelin is a nice touch

Blake, what was the size of the orifice you removed from the cannon to replace with the 1.1 mm oriface? There are a few cheap knockoffs of this same cannon and maybe they're not all built equal. Mine is an MATCC and the orifice I removed, after buying the one recommended here, looks like it has an identical hole size. I guess it doesn't make sense to remove one part if the "upgrade" part is the same.

@BlakesGarage

4 жыл бұрын

1.3mm was the stock size most foam cannons come with this size. It’s very hard to tell the difference as it’s not much smaller but it makes a huge difference.

New subscriber broh thanks for Sharing!

With what towek do you dry the car?

You held it on there longer buddy of course it's going to be thicker

@edubb2491

4 жыл бұрын

I noticed that too!😂

Could you tell me please, will the foam canon be still affective if the plastic pipe, that is in the bottle, will be much more longer?

@jeffk3192

2 жыл бұрын

the tube in the bottle should likely be slightly longer than the bottle itself so that full screwed in it bends to the side. That lets u get the last bit out easier. If your talking about hooking up plastic aquarium tubing to move the heavy bottle off your wand it would prolly work but the soap solution would take a while to siphon up the tube before it reaches your tube which is a bit of a hassle imo

1:30 you gotta coat that small area for a bit dontcha

That’s a mikuni jet I have quite a few. Did you bigger on the jet or smaller ?

@Jonathan-L

3 жыл бұрын

I really hate it when good questions like yours don't get answered :(

I have the same foam cannon, don’t have a wand but it connects right to the gun of my pressure washer, tried spraying it and water shot out, tried twisting the nozzle as well as the twisting thing on top and pure water, any recommendations ?

@BlakesGarage

4 жыл бұрын

Take it apart something maybe clogged or linked in the soap feed area. I've never had an issue with mine.

Honeydew by CG is one of the best pre wash soaps out there. People are just haters...

@akidim13

5 жыл бұрын

What you mean by pre wash soaps

@mistersleep7

5 жыл бұрын

@@akidim13 a soap that is applied, usually with a pressure washer/foam cannon, and left to sit and breakdown dirt and road grime before being rinsed off. It's a good technique for preventing swirls on very dirty cars to get a lot of the crud off before you even touch the paint with any towels or wash mitts. Although being honest for most well maintained cars this is a waste of time on anything except your wheels.

@Hondaddy

3 жыл бұрын

It's hated on cause it's over priced ... Other soaps work the same or better for much less.

@mistersleep7

3 жыл бұрын

@@Hondaddy it's $25 a gallon on amazon...

@Hondaddy

3 жыл бұрын

@@mistersleep7 in america ... The world isn't living there....

Just wondering about one thing. I have 2 foam cannons (one is for just in case). With both on them, I've had the cannon on a vice with a long wrench on the quick connect. These things are so torqued on, they absolutely refuse to budge. How did you get yours loos the first time you did this?

@AB-80X

Жыл бұрын

They are more than likely fitted with loctite. Stick the quick release fitting in boiling water for two minutes, then it should be easier to loosen while hot. No need to dunk the whole thing in the water, just hold it in vertically so that the water submerges the connector fully.

I guess the question is: is Sookie thicker foam truly better at washing the car? If it just sits it's not actually removing any dirt where is the soap that runs off will continue to pull away and you can just recoat. It seems cool but I'm not convinced it actually does a better job cleaning your car

@BlakesGarage

5 жыл бұрын

The foam does run off relatively quick. So I would say it’s better at pulling the dirt away from the paint.

@BigWitter1

5 жыл бұрын

Thicker foam is better because it does not evaporate as quickly giving you more work time, the car stays wetter for longer with thicker foam, reducing chances of water spots, plus it acts as a lubricant allowing you to scrub the paint and not scratch and swirl the paint as much. you can also add all purpose cleaners inside the foam cannon to help breakdown tar and bugs.

@AB-80X

Жыл бұрын

@@BigWitter1 First off, foam is NOT a lubricant. What determines the lubricity is your PIR and the product in question. Secondly, thick heavy foam falls off in clumps, and if it is too dry, it does not do squat. Quality foam is a foam that is light which means it can be wet, but still cling for long enough. Snow foam does not evaporate either. It's tendency to collapse in on itself as some foams do, is either a trait of the foam, and sometimes a simple lack of quality. However, the latter is far from always the case. Especially some prewashes would not be able to do their job if they were too thick and did not create a wet surface. BH Touch-Less is a good example of this. Some add a foam booster to it and quickly find that it does not work nearly as good. If you get water spots because your foam dissipates, wash your car in the shade, or make sure your foam is not too dry. See that's the difference between an MTM and a MJJC. The former creates a lingering, but light and wet foam that does a lot of work, the latter just creates a thick heavy dry foam that looks cool on KZread, and waste a ton of product in the process.

whats a good electrical pressure washer to do semi truck ? something not super expensive but effecient and can connect that foam cannon too and water to wash it off later

@BlakesGarage

3 жыл бұрын

It would definitely do the job you can also buy a wand extension to get higher easier also.

Thanks

Do you know if the sunjoe can be swapped? I bought it from homedepot and I ripped up the box so now i am stuck with it

@Taylexwow

3 жыл бұрын

If you have a receipt you don't need a box to return to home depot

The honey dew is my favorite car soap

Do I need an adapter if I use that spray cannon and that pressure washer to allow it to fit together? Or is this all I need? Thanks

@BlakesGarage

5 жыл бұрын

That’s all you need it all connects together 👍🏼

We're do you get that at

Here is the next mod for you. Get a couple quick release fittings to put on the actual handle of your gun. Then you just swap the wand to the cannon and don't have 5 pounds hanging out there. Best setup I've used. You can then get some different length wands for different situations and swap them quickly as well.

@BlakesGarage

5 жыл бұрын

Great idea, I'll have to do that ASAP.

@phil7791

5 жыл бұрын

Idk why but if you watch videos from the USA most of the foam bottles are hanging off the end of the lance, but in UK they're attached right at the trigger. Normal lances with changeable nozzle patterns arent as common here in UK so maybe that's why.

@Sror3d

5 жыл бұрын

Blake's Garage yeah it’s a must! You might have to get a new gun but it’s better than having the wand.

@Itsyunlo

Жыл бұрын

You do need some sort of adapter to connect the cannon to the pressure washer right? Dont know why its not talked about more, not even on the box does it say 😂. My chemical guys big mouth even says something about quick connect but doesn’t say it’s not included.

I love your KZread channel

What is your psi, or litres per minute

Great video ! But this might sound lame of me to ask ,,but I got the sj 1000 and I bought a foam canon but I can't seem to take the wand apart to connect the damn canon

@richnet12

2 жыл бұрын

Dont remove the wand. Just attach the cannon at the end of the wand like you do with a nozzle.

I am confussecd, is this only washing the car, but not waxing it?

Mine came with 4 nozzles and a black one. Does that mean I can spray 35-35 ft with the right nozzle? What ration water to soap? I want to soft spray my blackened roof. Thanks

@johnnybrowning470

Жыл бұрын

Yeah I believe you talking about the pressure washer not the foam cannon.

Does the orifice need to flush all the way down or just till it's tight? Because the orifice I have won't go down it stops half way..

@BlakesGarage

5 жыл бұрын

Just until it seats and it should be fine.

I also bought a 1.1 orifice and it’s too small, just keeps on turning. So frustrating

What about adjusting the fan spray width to a smaller fan width on the spray cannon it self ... Just a thought ... Thanks for the video brother ... 😎

@BlakesGarage

3 жыл бұрын

That actually makes the foam more watery usually the wide fan seems to make the best foam. You can try with yours but it’s pretty easy to figure what works best.

I bought this orifice for my proklean cannon,but it didn,t work properly.Any info,guys?Is it a particular 1.1mm orifice for a Karcher k2

@BlakesGarage

4 жыл бұрын

Just buy the foam cannon I recommended and put it in that. Problem solved for $15 👍🏼

Does this modify work with pressure washer under 100bar ? (i used karcher k2 which is had only 90bar)

@BlakesGarage

2 жыл бұрын

Yes helps on any low psi washer