Thanks for the review. Can you please do a range test vs the turnigy RX?

Hohmies Mcfly Santez Morrow so I bind my x6b receiver with my I6X TX and sometimes the RX voltage is disappears from my TX and then shows again screen pls help me did I made the bind not properly?

is there any other page to buy the turnigy evo than hobbyking? They don't sell them currently...or do you think I should rather get the fs-i6x?

@AlbertKimTV

7 жыл бұрын

Try here - goo.gl/KPppUr

Does it have a return home function ?

Both using afhds2a i take it the binds to the turnigy evolution controller ? Also will the battery monitoring work like the, turnigy ia6c receiver that comes with the turnigy evolution ? It looks like they are both pretty similar in specs etc .

@AlbertKimTV

7 жыл бұрын

I haven't tried the battery voltage on the Evolution (it does bind). However, I have no reason to think it wouldn't work the same way.

@darrenduds20

7 жыл бұрын

Thank you for the reply, i have ordered one to try as im struggling to get the Ia6c as hobbyking seem to be out of stock at the minute.

Kindly how to connect the voltage sensor to pixhawk?

Hi Albert, do you have any idea if the X6B receiver will bind with either the Turnigy Evolution transmitter or the FS-i6S transmitter? Thanks

@AlbertKimTV

7 жыл бұрын

+Moises Moraga it will bind with both.

@moisesmoraga9618

7 жыл бұрын

Albert Kim. Awesome, thanks!

Hey Albert good video, but I couldn't see what you did with the vbat sensor alarms that is what I'm looking for. Can you set the alarm for 14 volts for example? Because within the fs-i6 the highest voltage you can reach in the External sensor tab is 10 volts , which is pretty useless when running 4S quads. THanks!

@AlbertKimTV

7 жыл бұрын

I think you might have to update your transmitters firmware. I can go above 10 volts.

@DashzRight

7 жыл бұрын

Are you talking about the i6X or the older sister the i6 cuz I'm talking about the standard i6.

@AlbertKimTV

7 жыл бұрын

+Dashz i6X. Did you try the open source firmware for the i6?

@litejk01

4 жыл бұрын

You could monitor either 1 cell or 2 cell of the battery and customize the voltage alarm based on those cell's performance. Most likely 1 cell should have the same "range" as the other cells of the main battery. (4.2 as full and 3.7 as - emtpy) (Since a 3 cell battery have 4 pins on the load charging plug)

Hey Albert can you verify that you can actually switch into AFHDS mode? There is some confusion in the forum about this. One person says even though the option is there it doesn't actually change modes. Hopefully you can clear things up.

@AlbertKimTV

7 жыл бұрын

On the RCGroups forum? I've definitely been able to switch to the old protocol cuz I am able to fly some of these micros with build-in receivers. Check out my QX70 videos. That has a built-in 1A receiver and I'm using the i6X radio to fly it just fine.

@RCFlyer85

7 жыл бұрын

Albert Kim Yeah in the i6x thread www.rcgroups.com/forums/showthread.php?2746447-Updated-Flysky-FS-i6X-2-4GHz-10CH-AFHDS-2A-RC-Transmitter-FREE-TEST Thanks...

I just got this receiver with my I6x and wondered how I would also use it for planes? My esc has a 5v BEC. Do I just need a 3 pin male adapter or something?

@AlbertKimTV

7 жыл бұрын

airplane setups can vary wildly so it's difficult to give an answer to this question. The X6B also has multiple input methods to further add to the permutations. It has PWM input so it would behave like any other receiver. Then there's all the radio setup that goes with the airplane as well but one could make 100 videos on that depending on what is being used. I'd suggest searching other videos on receiver setup for airplanes and maybe you'll find one that is close to your setup.

@usarmyfl1

7 жыл бұрын

Gotcha. Thanks!

Have you tried binding the x6b with the turnigy evolution tx?

@AlbertKimTV

7 жыл бұрын

+DimplePoji Yes, it binds

@DimplePoji

7 жыл бұрын

Albert Kim that makes the evo very appealing. Between this and the A8s, which would you recommend? And would i miss any of the rssi and telemetry function of taranis?

Is the Fs i6X compatible with receivers that have gyro? if so then what receiver?

@AlbertKimTV

2 жыл бұрын

I'm not aware of any receivers that have gyros. What are those?

Hi, I've just recieved the shuriken 180 pro(flysky) and turnigy evo. It came with the A8S reciever. All good but I've just changed reciever to the X6B for telemetry to the evo. Everything working except failsafe. Tried everything but can't get failsafe to cut in. Any help is appreciated guys

@AlbertKimTV

7 жыл бұрын

You have to play with your throttle channel range and make sure it goes below 980ms when you set the failsafe. Or an easier way is to set failsafe on your arming channel if you use a switch to arm which is what I do.

@senditfpv6538

7 жыл бұрын

Albert Kim thanks for your quick reply Albert. Failsafe was set on betaflight spot on and worked with A8S. I've checked it again. I just set failsafe on arming switch (2way on front of evo aux1) but now no arming.

@AlbertKimTV

7 жыл бұрын

So now it won't arm? I wonder if you're doing something wrong with the setup? Any way you can upload a video and show what your are doing? I think I'll need that to assist further.

@RCFlyer85

7 жыл бұрын

Tony Peart Did you set failsafe in the transmitter while connected to the receiver? In failsafe set your throttle channel to -100 (or 0%)

@senditfpv6538

7 жыл бұрын

RCFlyer85 I've found out the x6b early versions had failsafe issues. So I put the a8s back in and it worked perfectly. Shame as wanted telemetry

Will this still be able to bind to eachine BNFs with flyskys recievers like the QX95?

@AlbertKimTV

7 жыл бұрын

+Andre Martinez Yes

@madebyandre_

7 жыл бұрын

I have a question, are you familiar to the Flysky TH9X using the FS RM002 module? Will the module be able to bind to the QX95 and such?

@AlbertKimTV

7 жыл бұрын

Sorry, not familiar with those.

Can the ix6c run ibus?

@AlbertKimTV

6 жыл бұрын

yes

Will it work with the regular I6s

@AlbertKimTV

7 жыл бұрын

the receiver?

@Onlyone10184

7 жыл бұрын

Albert Kim also will I be able get battery telemetry

Can you help check if the USB cable come with the Tx works in simulators? Or is it just a data calble only good for F/W upgrade? Thanks!

@AlbertKimTV

7 жыл бұрын

+abghere It doesnt. Its just for firmware upgrades

@BrassStacks

7 жыл бұрын

Albert Kim , is there a way to use this on a simulator? How about using one of the simulators on Android? I was hoping to get a set of VR goggles and hooking this TX up to the phone to practice.

@AlbertKimTV

7 жыл бұрын

Unfortunately, this model won't work with simulators. The USB cable is only for firmware updates.

@BrassStacks

7 жыл бұрын

Albert Kim , Oh... well... That changes things. Thank you for the quick reply! Is there an entry level TX that you recommend? I would really like the new Evolution but it's sold out everywhere. The Taranis Q7 (I think it's called) isn't out yet.

@AlbertKimTV

7 жыл бұрын

Last I checked the Evolution was back in stock at the Internation warehouse. The other entry level radio I can recommend is the FlySky i6 transmitter. It's about $40 to $50 and is very reliable and has good range.

Hi kim, i got i6 with firmware mod to ibus&10ch and i got cvt01 voltage sensor and i really like it. ia6b and cvt01 weighs 14.5g+6g vs x6b 6g. The i6x seems to have sigS what the i6 dont have.I could use sigS but if there is no warning beeps its useless. The modded firmware has 2 stage beeps. My question is. Can you update the i6x firmware and get 2 stage beeps on sigS and volt. If so i will update my gear. not sure if mod firmware has sigS.. github.com/benb0jangles/FlySky-i6-Mod-

@TheMadmacs

7 жыл бұрын

yeah i have the 10 channel mod too courtesy of iforce2d's vids and others. i have signal % but no warning beeps (which are too quite) i'm not clear yet what the x6b or or i6x can do as far as voltage and signal warning, there is a port for battery voltage though but no clear info yet??? iforce2d also did a teardown and the new i6x is significantly redesigned inside,,, i'm really hoping the evolution gets a hack to match the 10 channel one.

@AlbertKimTV

7 жыл бұрын

+LazyFPV I'm gonna investigate the alarms more for future videos. I'll have to run some experiments as the documentation is very poor.

Every time I do a front flip with this transmitter I flip the kill switch accidentally and I just fall right out of the sky! Don't really like pinching with this one. But it is a great radio for the money. Nice video!

yes

@AlbertKimTV

7 жыл бұрын

Yeah, the X6B receiver will work with the i6S and the Turnigy Evolution.

yeah what is it with the names.. the a8ai8asxsa88assb

And to connect PWM to ESC and Servo's directly you can use this adapter: www.ebay.com/itm/184100616268