This is really proving to be a great radio. I have achieved one kilometre with an f949 (yes FPV on a 50 gram plane!) running in AFHDS only, and with my Hawksky and X84 wing with x6b and iA6B receivers on AFHDS2A, over two kilometres so far with no failsafes. You can disable telemetry, and it also has hall effect 4k gimbals, you can easily exchange any of the other two position switches for three position, or pots, unlike the older i6. I have just changed the batteries for the first time after months of flying with it, and my only problem was the power switch recently getting very stiff. I popped it out and greased the back face and it is good again. One important upgrade that is required (listening flysky?) is to have audible alarm option available for RSSI. The value is there available on screen, but useless while flying fpv if you can't read it, it requires an audible warning, so hopefully a future software upgrade will address this. The battery voltage alarm, although quiet compared to my Taranis is still ok. I currently have over ten planes and two heli's running with this radio, and I get way less failsafes than with any of my frsky X series receivers on the Taranis, actually nearly double the range. Love it, I can actually trust it.

Nice Review. Does the Rx have an RSSI output voltage that can be used with an OSD board like the minimo OSD?

Great presentation. Wanting to find out if the tx is compatible with Bind and Fly planes like a Spektrum TX is with Hobbyzone planes.

Hi, good video. I have a question; can you set an alarm for a 4s battery for example, to start beeping at 14.0v? I have tried to do it with the I6 but it seems impossible, the rx voltage threshold only goes up to 10 volts..

Ty for the review man! But noone talks in detaill where to connect this battery sensor cable on the fc. I'm new to this and prepairing to build my first quad with this receiver. On every video they hook it on the battery. Other say solder to the pdb. Isn't it ment to connect to the fc?

Hi, do you have to use a flip 32 to connect the servos to the X6B receiver ? Or is it possible to connect the servos directly to the receiver ?Thank you.

This RX does a great job sending the right voltage sensing to my fs-i6 (no X), however I am having problems getting the TX to sound an alarm when my 4s is low in voltage. The TX alarm setting only go as high as 5v. Ideally, I need the alarm to sound when the voltage goes below 14.4v. Is there anyway to solve this? Does the i6x TX allow this alarm to be set? Can I upgrade the firmware of the original i6 to have the alarm work properly.

its nice to see flysky adding new stuff, i hope the new wireless updates aren't just a lock out for people to hack the new radio, they do look a bit nicer than the old i6, woulda been nice to have a usb port to use with flight sims.

Could you show the screens for each of the menu options?

hi! which is better between fly sky i6 with fs ia6b and i6x with x6b? and range? thanks

Hohmies Mcfly Santez Morrow so I bind my x6b receiver with my I6X TX and sometimes the RX voltage is disappears from my TX and then shows again screen pls help me did I made the bind not properly?

The interface looks identical to the previous model. Can you please tell/show where they added 4 new channels?

Which firmware have u updated to this tx. I am not able to find any new firmware to this tx. Plz inform if there is a new firmware.

Hi, how many 3 position switches does the transmitter have? Thanks

Hey there, Are you gonna release a new video on this transmitter soon? I am still interested in the voltage port... Do I need an extra sensor or is it like the Turnigy one where you can connect the voltage directly? And can you say something or share some pics of the internals because people are speaking about possible hardware upgrades?

@DronesVisuals

7 жыл бұрын

Hello and thanks for asking. I apologize for the delay, I do have plans to do some more videos about it, but I´m just really short on time and there are more products I need to review. I´ll do my best to get some more viids out. Cheers.

Quick question. Would this work with the Turnigy Evolution? How about Voltage reading/sensoring?

@DronesVisuals

7 жыл бұрын

Hello and thanks for asking. I´m not sure whether it will work with the Turnigy. For voltage transmitting you would need to hook it up to a sensor. Cheers.

I think I'll get 1 of these to test and I am super excited... 1 question. Are the holes on the receiver spaced to allow it to mount on top of a Flight Controller?

@DronesVisuals

7 жыл бұрын

Hello and thanks for commenting. Nice! Oh, good question. I´ll try that, didn't think about it. Cheers.

@RCFlyer85

7 жыл бұрын

Drones Visual did you get a chance to check?

@thmls5744

7 жыл бұрын

RC Flyer85 same question and still no answer

Hi there, is the Fs i6X compatible with receivers that have gyro?

Hello. Please help me. In the FS-i6X model, USB signals are already output to the connector, not UART. This means that a UART converter is not needed and you can connect directly to USB. I understand that you can update the firmware via USB. But I need to know how to link 2 remotes to train a student and how to connect it to a computer for the trainer. Questions: 1.Can I use the USB connection for simulator training? 2. Will it be possible to connect a computer directly to the PPM output of the Tranier connector through the sound input of the card? So how do they do it in the FS-i6? 3.How to connect the remote control to another remote control. Should I connect the pin bus to USB or take the PPM In and PPM Out pins?

Thanks for the nice video on Flysky Fs i6x. Finally, i got mine arrived yesterday Flysky FSi6x and was trying to bind it with Wltoys F959, F949 and F939. i was able to bind it with Wtoys F959 and F949 but despite trying several times i was not able to bind it with Wltoys F939. Would appriciate if you can share any ideas to get my Flysky FSi6x bound with F939. Thanks

can I bind this transmitter to I bus receiver without using flight controller and bind using esc and battery

Hello, how to get voltage of the battery on screen, i ma newbie, and don't know

can you elaborate more on how you update the firmware wirelessly? does it have a bluetooth or wifi chip? otherwise how does the transmitter gets the new firmware? so you said the voltage monitor allows 1-4s, why do you need an external voltage sensor? isn't it included on the receiver? to me it looks like they are using the exact same hardware, updated the firmware and made a new receiver and put it as a new product. as you all probably know there is a community firmware that allows 10 channels also on the old transmitter.

@DronesVisuals

7 жыл бұрын

Hello and thanks for asking. Yeah, I´ll elaborate more on that as soon as I try it. There is a dedicated port in the receiver for the voltage sensor, the receiver itself does not seems to offer that option. This receiver will allow up to 18CH via iBus. Cheers.

Can i get RSSI signal for OSD with this Receiver?

TQ good tutorial

@DronesVisuals

7 жыл бұрын

Hello. Thanks. I´m glad it was useful to you. Cheers.

Can you tell me the number of mixes present in i6x ??

Is it worth it waiting on a FS-i6X preorder or just get the FS-i6? Waiting for my first drone but will take a whole month for this controller :(

@DronesVisuals

7 жыл бұрын

Hello and thanks for asking. What receivers will you be using and what quads will you be flying? Cheers.

@Amivit

7 жыл бұрын

Wizard X220 with "Flysky FS-i6X 2.4GHz 10CH AFHDS 2A RC Transmitter With X6B i-BUS Receiver". My first time :)

good video, will it work with a Drone with a FlySky reciver? Thanks

@DronesVisuals

7 жыл бұрын

Hello. Yes, it will. Cheers.

Nice video! Id the reciever compatible with the i6s?

@DronesVisuals

7 жыл бұрын

Hello and thanks for commenting. I´m glad you like it. Yeah, it is, but still need to test it to be able to confirm it. Cheers.

Hey sir, salam. I didnt understand english so much but i want to ask, is this flysky fsi6x default channel is 10? I read default channel is 6. So, is the flysky fsi6s better?

@DronesVisuals

7 жыл бұрын

Hello, the FlySky FS-i6X is 10 by default. Cheers.

@DronesVisuals

7 жыл бұрын

I mean that you don't need to change the firmware to get 10 channels, you can select them directly. Cheers.

@elliotrees4451

7 жыл бұрын

Woooah thanks 😃

This has been long overdue. I guess with all the Micro Quads Banggood/Eachine have been putting out they got around to making a mini RX for Flysky. The little QX95 and others probably have this little RX on board.

@DronesVisuals

7 жыл бұрын

Hello and thanks for commenting. There is another smaller one that I expect to be showing soon. Cheers.

It looks like you can mount the receiver above the fc and pdb with the 2 holes in the receiver

@DronesVisuals

7 жыл бұрын

Hello and thanks for commenting. Indeed, someone mentioned this to me before. I will check whether the spacing matches. Cheers.

@RCFlyer85

7 жыл бұрын

Yes, that was me.... any updates???

Hello, just want to ask, does it still support ald AFHDS protocol? because this rx are still to big for a micro quad, and all micro rx for flysky fight now only support AFHDS and not AFHDS 2A, thank you

@DronesVisuals

7 жыл бұрын

Hello and thanks for asking. It supports AFHDS 2A which includes the FlySky FS-i10, FS-i8, FS-i6, FS-i6S, FS-i6X, FS-i4 and FS-i4X. Indeed it's rather large for a micro, but FlySky has released another receiver, smaller, that might be suitable for micro. Cheers.

@devilbur0

7 жыл бұрын

hum, it looks like flysky really leaving AFHDS now. What's their smallest rx available now? thx

@DronesVisuals

7 жыл бұрын

More on that smaller receiver coming up soon. Stay tuned. Cheers.

@peterwoo2489

7 жыл бұрын

You can use choose between the two just like the i6

@devilbur0

7 жыл бұрын

Peter Woo it did out of box with official firmware ? because none of the description, and any video review mention about it, and latest releases of Flysky TX only support AFHDS 2A (fs i6s) in the other hand, those x6b is quite neat, maybe it's time to upgrade my radio system

i have the FS-i6S + ia6b, is this a good upgrade? how about range? +/- same?

@GoncaloSantosHit

7 жыл бұрын

Fs-i6X and X6b about 2km?

@GoncaloSantosHit

7 жыл бұрын

Ok Thanks!

have you tried to bind the i6x rx with the the i6 tx

@DronesVisuals

7 жыл бұрын

Hello and thanks for asking. Will try that today and let yo know, but it should be compatible. Cheers.

This receiver include s bus signal???

Nice! I wonder if the receiver is compatible with the old i6...

@DronesVisuals

7 жыл бұрын

Hello and thanks for commenting. Yeah, it is compatible. I will try that next. Cheers.

I just receive this today. It comes with an USB - SVideo cable to connect it to a PC, but it dont seem to work, any help?

@DronesVisuals

7 жыл бұрын

Hello. Do you want to use it with a simulator? Cheers.

@cobealex

7 жыл бұрын

Yes, I would like to.

@alchemicalanarchist

7 жыл бұрын

That cable only updates firmware, you need another type of cable to use as a Simulator you can find it on amazon

Great! What it's the range difference betwen the FSIA6B? And where I should connect the yellow cable of the voltage sensor? (Por cierto eres español?)

@DronesVisuals

7 жыл бұрын

Hola y gracias por preguntar. El rango max del FS-X6B es de 300m. El sensor del voltaje se conecta en la toma que se encuentra sola en la parte inferior del recibidor. No soy espanol, pero si hablo espanol. Puedes ver mi canal Torrente Digital donde tengo algunos de mis análisis en espanol; no solamente drones sino otros productos también. Saludos.

@BelloDDC

7 жыл бұрын

A vale gracias, pero el cable esse trae uno de color amarillo no? ese donde va?

@DronesVisuals

7 жыл бұрын

Todos los cables con los conectores se conectan al recibidor. Luego algunos van al controlador de vuelo, otro iria al sensor de voltage. Saludos.

@BelloDDC

7 жыл бұрын

Vale, merci

can i use i bus receiver for rc planes

Will this control any of the tiny whoop style quads?

@DronesVisuals

7 жыл бұрын

Hello. It should control the ones that are FlySky compatible, but i have not tried them out. Cheers.

@OlliGarch

7 жыл бұрын

Thank you.

@nicobreeliant

7 жыл бұрын

It might be to heavy though.

What is it's range in km?

You mention range about 300m, but regular FS-i6 has confirmed range more than 1.5km. Could you test it?

@DronesVisuals

7 жыл бұрын

Hello and thanks for asking. Yeah, the range of this transmitter is shorter. I have not tried it yet, but that's what FlySky states so, so I do expect a range of around 300m, will update when I test it. Cheers.

@peterwoo2489

7 жыл бұрын

Is the hardware the same? If it is, it will have the same range. 300m is just absurd. The range, of course, varies with the receiver being used. It will however have shorter range compared to the ia6b which uses two dipole antennas. Please check if the hardware is the same. Just post a part two comparing the insides of the two receivers. (or does that violate the reviewer's contract if there is one)

@RCFlyer85

7 жыл бұрын

The range mainly depends on the receiver. So I think they mean that the receiver that comes with this bundle is only rated at 300m... If you use an ia6b i'm sure you'll get the full range of the previous transmitter

@DronesVisuals

7 жыл бұрын

Hello, Indeed RC Flyer85 has already replied. Cheers.

When it's related I mean what is the release dat of Flysky FS i6x. ????

@DronesVisuals

6 жыл бұрын

Hello. Do you mean, when was this transmitter officially released to the market? Cheers.

are you able to flash the old i6 with i6x firmware?

@DronesVisuals

7 жыл бұрын

Hello and thanks for asking. I haven't tried that yet. Cheers.

@randylachman5273

7 жыл бұрын

can you please try it and reply back ?

@larsmartintangen7072

7 жыл бұрын

Randy Lachman you can't do it as the transmitter is wery different on the inside

@larsmartintangen7072

7 жыл бұрын

But there is firmware for the i6 that give 10ch ppm

Where can i get the voltage sensor?

@DronesVisuals

7 жыл бұрын

Hello and thanks for asking. Let me check whether they sell one and I´ll get back to you. Cheers.

@krallopian

7 жыл бұрын

Any news? =)

Hi, great video, if you can open the Flysky FS-i6X and see what is in for the new output mode and know if we can place in the Flysky FS-i6, is it very good. :)

@DronesVisuals

7 жыл бұрын

Hello and thanks for asking. All right, I´ll check that out. Cheers.

@onclefly8450

7 жыл бұрын

Thank you :)

@conway310

6 жыл бұрын

Jason

Can we have spring loaded throttle for fs i6x

@DronesVisuals

6 жыл бұрын

Hello. Yeah, it is possible, but need to do it yourself. Cheers.

Hola tienes este mismo análisis en español? en tu canal de torrente digital. Gracias

@DronesVisuals

7 жыл бұрын

Hola. No, este no lo he hecho en espanol. Saludos.

which one is the s bus port.

@T3hFr00bSh0w

7 жыл бұрын

the one he didnt plug into.

will it work with 1s

@DronesVisuals

7 жыл бұрын

Hello and thanks for asking. Do you mean the mini receiver? Cheers.

D\V I have the FlySky FS-i6X Transmitter and FS-X6B 6 Channel 2.4GHz Receiver can I use it with my Blade 130s rc helicopter and how can i get it to work PLEASE

@litejk01

4 жыл бұрын

If you are using regular servo's and such, I would recommend to connect the PWM plug to this board: www.ebay.com/itm/184100616268 But I do belive that Blade 130c uses their own connections?

@anmwolfrc159

4 жыл бұрын

thanks for the information god bless will try it and see if it works

could you just hock the wires for the voltage sensor going out from the rx straight to the soldering points of the battery cables without having them burned though ?

Hi I just subbed to you and I'm in a big dilemma with what to get, these are my options a Cheerson cx20 or Xk detect x380 and add gimbal, firefly 6s and Fpv, or a hubsan h501s with Fpv and gps and osd and possibly could add a gimbal but other youtubers don't recommend, then the cg035 I'm really interested in cheap gps quad with brushles motors and then add a gimbal which I would love to see you try that out a gimbal on the cg035 , or last option is bayang toys and add gimbal and Fpv but yours had a flyaway and I really want gps how you reply

Dont buy this flysky i6x its better to buy flysky i6 because it has custom firmware which is updated but flysky i6x you cant upload new firmware its just impossible it will show you that you have flashed your transmitter and then when you go to firmware ver. its same like before ... Better buy Flysky i6 you have more features then i6x the range is same ... Edit: There is custom firmware for flysky i6x its written from same guy who wrote firmware for i6 so now i6x its better option then i6

@DronesVisuals

6 жыл бұрын

Hello and thanks for sharing. Cheers.

@swugger

5 жыл бұрын

Fuck I just bought the i6x

@swugger

5 жыл бұрын

Nm

what is its price?if anyone knows plz tell me.... thanks

@DronesVisuals

7 жыл бұрын

Hello. Check out the link in the description. Cheers.

And to connect the PWM to regular ESC ( Electronic Speed Controller ) and use regular 3 pin Servo's. You can use this adapter board: www.ebay.com/itm/184100616268

W Polsce dostępne tutaj: avifly.pl/pl/aparatury-drazkowe/fs-i6x-fs-ia6b