Great video well done. Good clear voice and close up with the camera. No stupid music going in the back ground. I just had my 06 Honda Ridgeline done.

@klowny1969

6 жыл бұрын

Arthur Smith thanks

You provide such great material to your viewers. I appreciate all of your hard work. I truly appreciate it!

@klowny1969

Жыл бұрын

Thank you for commenting

"I'm not gonna use a torch for you DIY guys," then proceeds to use a lift and numerous pneumatic tools.....

@klowny1969

7 жыл бұрын

Lennon Morales hahahaaa .. u dont need a lift to go underneath a vehicle..and the pneumatic tools arent necessary as well, although alot of diy guys do have air tools..thanks for watching and commenting

@nananooknak

6 жыл бұрын

Lifts aren't terribly expensive, it's having foundation that make the means

@psky1921

6 жыл бұрын

True, but it added to the humor!

@W333dm4n

5 жыл бұрын

B R E A K E R B A R S

@cryptogaming6266

5 жыл бұрын

Lennon Morales haha yeah as soon as he says yeah I’m going to use this air hammer, I’m like yeah I don’t have that

I enjoyed watching this. I miss working on cars. You having fun with all those tools and techniques. I am 50yo and worked in IT for past 25+ years. I missed the normal work instead of this abstract work. I came to see the $300+ charge for replacing this on my car.

@klowny1969

2 жыл бұрын

Thank you for watching and commenting and don't forget to subscribe

one of the best detail video in a while

@klowny1969

Жыл бұрын

Thank you!!

when buying ur bolts at hd, or wherever, make sure to get stainless hardware to keep the rust at bay.

This goes by so well when you have the right tools

@skip741x3

4 жыл бұрын

yep! try doing that lying on ur back with the car wedged right over ur face and armed with nothing but a ratchet,vicegrips and a hacksaw! oh , AND LOTS OF PENETRATING OIL!

Luv the commentary. New follower

Good job bud. I have all the same tools as you except that beautiful LIFT! I'd never leave the garage if I had a lift like that!

@klowny1969

7 жыл бұрын

Fireship1 i usually spend the entire weekend in there lol

@michaelreece458

6 жыл бұрын

Real men use goddamn jackstands.

@jonniewadd56

5 жыл бұрын

@@willem2544 LOLOLOL!!

@Godhorse6969

3 жыл бұрын

@@michaelreece458 peasants use jack stands

@teslarocks7345

3 жыл бұрын

@@michaelreece458 Guys like me pay a guy like that to do exhaust work cause crawling underneath to do that forget it.

This is your 2nd video that saved me big $$ on my Focus. Thanks--keep it up! One thing I wanna point out is that that flex pipe is for the 2.3L Focus PZEV engine, which makes sense since you're in NY (a PZEV state). The 2.0L Zetec was the most popular engine and is what most 01-04 Focus owners watching this video probably have. The pipe for that engine is the Walker 52243

@klowny1969

7 жыл бұрын

1975augusto kool!

Great video man! This was very helpful! Now I know how to change my own flex pipe!! 💪

@klowny1969

6 жыл бұрын

ShayButtaTV thanks for watching and commenting

nice video klowny love the work love working on my car

@klowny1969

7 жыл бұрын

Thank u sir

Nice work straight to the point no bs great video

You made short work of that! Loved the humor!!! Too many damn people trying to convince others to be PC in this crazy freakin world. Think and say what want,but leave others the F alone! Btw, and you seem like a smart dude and may already know this, but for those that don't, Kroil is great for cleaning gun barrels as well. Cheers

@klowny1969

7 жыл бұрын

MG-70 lol screw pc hahaaa yeah kroil is used for a ton of stuff..thanks for watching and commenting

love the klowny tube channel

@klowny1969

7 жыл бұрын

bigwillywes78 thank u sir

Another job well done, yes sir . Cheers buddy.

@klowny1969

7 жыл бұрын

STEVE ROB thanks for stopping by again and watching

Good video, nicely done!

@klowny1969

4 жыл бұрын

thanks for watching and dont forget to subscribe

Nice job

Thanks - replaced my flex y pipe on my Enclave… very similar and wasn’t too bad ($200 no torch and 3 hours)

@klowny1969

2 жыл бұрын

Awesome! Glad i was able to help you out..don't forget to subscribe

must be nice having all that space to work

Thanks you made my day

@klowny1969

6 жыл бұрын

Steve Mick thank u

I like the humor and good work

@klowny1969

3 жыл бұрын

Thank you..don't forget to subscribe

Nice job dude

@klowny1969

6 жыл бұрын

john smith thank u

Good job, Bro.

@klowny1969

6 жыл бұрын

Narin Van thanks!!

Nice job well done..

@klowny1969

6 жыл бұрын

Taj Tomlinson thanks

My idea worked. I think I found my exaust leak.To listen better, I put my ear muffs on to drown out much of the vacuum's noise. I used the blowing end of the vacuum.

Good informative video. Thanks!

@klowny1969

8 ай бұрын

Thanks for watching and don't forget to subscribe 😉

Dang i don't have 3 hands like you! Good video man thanks

@klowny1969

3 жыл бұрын

lol glad i was able to help..dont forget to subscribe

Excellent. Thanks!! 😊

@klowny1969

Жыл бұрын

Thank you..don't forget to subscribe

“hello ladies” 😂

@tonistarks2874

3 жыл бұрын

🤣🤣🤣

@ArabMoee

3 жыл бұрын

😂😭

hola amigo se le puede añadir silicon gris a la junta para que selle en caso de haber fugas???

Oh it must be so nice to have a bolt on flex pipe. Very useful indeed.

@klowny1969

2 жыл бұрын

Yes it's handy..don't forget to subscribe

nicely done.

@klowny1969

7 жыл бұрын

Thank you

I love your "intro" 🤣🤣🤣

@klowny1969

3 жыл бұрын

Thanks for watching and commenting..and dont forget to subscribe!

Great job

@klowny1969

11 ай бұрын

Thanks..don't forget to subscribe 😉

good work

@klowny1969

2 жыл бұрын

Thanks..don't forget to subscribe

Thank you!

@klowny1969

Жыл бұрын

Thanks for watching and don't forget to subscribe

what brand and model air hammer is this? I noticed the straw on the pent fluid can was longer then the standard can where did you get that ?

Nice homemade bandage.

@klowny1969

Ай бұрын

Thank u..don't forget to subscribe 😉

very good

@klowny1969

Жыл бұрын

Thanks don't forget to subscribe

Having four hands is really helpful.

@klowny1969

4 жыл бұрын

I thank my lucky stars..dont forget to subscribe

The studs at the cat on the manifold on an 07 are a real PIA.

@klowny1969

Жыл бұрын

Yep! Thanks for watching and don't forget to subscribe and hit that bell

@hoipolloi890

Жыл бұрын

@@klowny1969 I hit it after giving it a little shot of butter sauce.

What year focus & is it diesel? Mine focus-max 2.0lt tdi 2006, needs the same, is this the same part number? Cheers

I have an ‘09 Hyundai Accent as a fixer up... and definitely gonna try doing this myself, this time around. I got charged $180 for my Malibu. When the item itself was $30. 🙄

@klowny1969

5 жыл бұрын

Yes, you should..thanks for watching..dont forget to subscribe

How long they last I just got mines done on my Camry ? Usually with my truck I didn’t need a flex pipe.

@richieschmidt6225

4 жыл бұрын

Zionic-iDrxp-YT has to do with FWD vs RWD (usually). A lot of RWD vehicles don’t use flex pipes

hey can you do a video on Chevy impala rack and pinion need a little help

@klowny1969

7 жыл бұрын

Dominic Fincher if i do that job..ill film it

I got a nice beefy air hammer!!!

Your accent and not seeing your face I'd swear comedian Anthony Jesilnek was doing an automotive video.

@klowny1969

Ай бұрын

It could be!!

@neurodadvirgent

Ай бұрын

@@klowny1969 this is a twist if I've ever seen one! 🤣

I'm glad your socket didn't break

@klowny1969

6 жыл бұрын

Carlos Antonio Lopez Chavez say what?

damn klowny, how many hands do you have? no wonder you so good at fixing cars, and maybe at other things lol at 6 min.

@klowny1969

7 жыл бұрын

Bob Smith lol .. more hands the better haha

man you're the best.....just subscribed.....makes me realize I need to invest in good tools....etc

I just had the flex pipe done at an exhaust shop here in Philadelphia.. 2006 Nissan Altima.. $120.00..

@klowny1969

3 жыл бұрын

Thank you for watching and commenting..don't forget to subscribe

so can you do a tutorial on how to change the spark plugs of a third gen Camaro? I have a 1992 Rs Camaro hatchback and I have never worked on a car before, it's a piece of shit but it's my piece of shit. it's my first car and I want to learn how to do stuff on it. your videos have helped me out allot.

@klowny1969

7 жыл бұрын

Jonathan Criswell if i get a chance to, sure..thanks for watching and commenting

Holy shit man, this was awesome! I don’t know shit about vehicles but I’ll fucking learn watching you! Lol thanks so much for sharing!!!

@klowny1969

3 жыл бұрын

lol thank you..dont forget to subscribe

@kenswope8822

3 жыл бұрын

Hey

"Gonna tap it, like a bitch that ows me money" lmao

homeboy your fucking entertaining, i need more videos from you!

@squirrelcovers6340

2 жыл бұрын

You're *

On that second flange since it's an actual nut and bolt you could tighten instead of loosen and just snap it and replace nut and bolt. It's sometimes easier to do that instead of trying to get it loose. I have done this and it works. I wouldn't do that with studs of course, but if it can be replaced, why not?

@klowny1969

Жыл бұрын

Thanks for the advice! Don't forget to subscribe

diy says the octopus with a full toolbelt.

I can always tell when a guy knows what he's doing. Looks like you know all the little tricks. If you wouldn't have hit the bolts with the pneumatic chisel it most likely would have broken the bolts off when you removed them. Great job.

@klowny1969

6 жыл бұрын

victory21222 thank u

Kinda like the sex scene from the Watchmen and Dr. Manhattan where suddenly there are more than two hands doing the 'job'. Thought you were by yourself until then. :-)

@klowny1969

6 жыл бұрын

39knights LOL

An induction heater would make quick work of those rusty nuts. Today they are a $500 tool any shop can afford.

@klowny1969

4 ай бұрын

Yes I have that tool, I tried to gear this toward the average diy person..thanks for commenting and don't forget to subscribe

Are the flex pipes common to go bad on these cars?

Excellent video, thanks bro!!

@klowny1969

5 жыл бұрын

Thanks for watching

Hi Klowny1969, could you recommend andy video's on air tools please, I picked up an impact wrench here in UK 2nd hand no instructions, it has settings one to 4, I am unsure how to determine what settings to use as scared of breaking bolts, also do you set the compressor at say 90psi before you press the trigger on the tool or does it need to be say 90 psi when using it, also as I see how hold spanners on the other end while using air tools is this ok when using certain settings as scared of breaking my arm, excuse my ignorance but I would like to learn, many Thanks Ian

@klowny1969

7 жыл бұрын

sandydogy i keep everything maxed out..150 psi on compressor and highest setting on gun..ignore the recommended 90 psi, u would never take anything off...snd only use impact tools when taking bolts off..not putting them back on, unless u know what ur doing

@sandydogy

7 жыл бұрын

klowny1969 thanks

what was the name of the penetrating oil in the spray can? Nicely done BTW.....

@klowny1969

7 жыл бұрын

Thank u..i used kroil ..thanks for watching and commenting

👍👍

@klowny1969

7 жыл бұрын

juiced71 thanks

"my favorite personal lubricant" hahahahaha

@klowny1969

7 жыл бұрын

stopherrr yeah babyy

@stopherrr

7 жыл бұрын

tap the bitch like she owes me money dude I love these videos

@klowny1969

7 жыл бұрын

stopherrr lol thank u

No engine light for broken flex pipe?

Took care of that Ford

Man is only as good as his tools

@Zx14rrrrrrrrrrr

4 жыл бұрын

Na I don't own a crazy amount of tools and still know way more than some guys that do.

Impact gun with chrome socket. Good plan.

@klowny1969

6 жыл бұрын

GophukYerselv I'm rich..I can afford to mess my sockets up

@jimturcotte5519

5 жыл бұрын

I was looking at impact sockets at Lowes a few years ago. Guy there talked me into going cheap becuase they have a lifetime warranty. So I did.....lol.

What does the Andi seize do for the bolts?

@valpanig

2 жыл бұрын

protects socket from stuck rusted nuts

I'm here cause I have a 2009 HHR that just rolled 100k a month ago and low n behold the engine light came on for 3 days. Then went off as soon as I borrowed a friends code reader. It still came up with a code even without the engine light on. The code $7E8:engine and $7EA. I've looked all over the web and came up with "Hot oxygen sensor" and cracked flex exhaust pipe. Does this sound right to you or anyone in comments? Will replacing the flex section like you did here reset the engine warning light? Just looking into it before going to a shop and hearing what they think and will charge. Thanks for your time and cool video.

@handsomyoungman

5 жыл бұрын

idk but if your car sound louder than usual when you start it and it makes lot of noise when you drive then you need a flex pipe . run you about 180-350

What size are those 4 bolts? Thank you!

@daniellaudman8580

2 жыл бұрын

3/8 x 1 1/2

What is part number for that flex piece.

I bought a aftermarket header tht came with a new flex pipe. now the car makes a ticking noise. don't see any leaks anywhere but I heard the flex pipe that comes with headers is junk. can a ticking noise come thru a cheap flex pipe

@klowny1969

4 жыл бұрын

ticking noise is usually a leak..dont forget to subscribe

off topic a bit but is it okay to spray the engine with degreaser then rinse it off without damaging anything? Sorry if it's a dumb question.

@klowny1969

7 жыл бұрын

Kevi O u can just becareful u dont get any of the wiring wet

Have you ever changed the rear gate trunk support shocks on jeep grand cherokee? I'm willing to lend mine for a demo....😉

@klowny1969

7 жыл бұрын

Edie Mazzullo lol ive been so busy..unless ur willing to wait two months or so

@mazz588

7 жыл бұрын

😓bummer

@klowny1969

7 жыл бұрын

Edie Mazzullo sorry..i have two people waiting for the cars to be done..hope all is well with u and ur family ☺

@mazz588

7 жыл бұрын

No worries buddy. miss you so glad you're busy.. busy is awesome. 😄

@klowny1969

7 жыл бұрын

Edie Mazzullo thanks 😊

Not sure if it was anythingto worry bout but what was the water bubbling when it was started

@klowny1969

3 жыл бұрын

i dont think it was anything...probably AC condensation..i would have to look at the video again..dont forget to subscribe

on the vid your part has complete ends included instead of just the flexi , do u sell exactly what you show at 4.57? thanks

@klowny1969

7 жыл бұрын

karl mah take a look at rockauto.com

@benram9062

7 жыл бұрын

thanks , i thought the adverts under your video were from your company , shame you are across the water, great vid , all the best

@klowny1969

7 жыл бұрын

karl mah yup not mine..thanks for watching

I dont miss working on that eastcoast salty crap.

@klowny1969

7 жыл бұрын

russellfheim everything and anything i work on is rusted to sh1t!!

@russellfheim

7 жыл бұрын

HA, Yea, one hand a torch, the other an IMPACT socket.

@chrisafp071

6 жыл бұрын

I love the rust feels so good.

Was that flex pipe and flanges welded by you or was it a one piece bought at the local autozone

@klowny1969

5 жыл бұрын

One piece..I mentioned in the video the part number I think

So at 2:39 he says “I’m gonna tap my mom cause she owes me money”, very classy... bet she would be proud...

@klowny1969

6 жыл бұрын

I would never say that..not me..no way sir

@chrisafp071

6 жыл бұрын

Tap the bitch like she owes me money is what he said. You clearly can't hear shit....

@bobvilla7230

5 жыл бұрын

Chris Taylor u clearly can’t either fucktard

@chrisafp071

5 жыл бұрын

@@bobvilla7230 xD

@ryanmullis3571

5 жыл бұрын

Tap YOUR mom. Cause she owes me money. You're just being stupid. Walk on home boy.

Clown-Thanks for the vid. Doing some research as my sons car just failed inspection. Exhaust "loose, leaking joints". An 04 Camry, and I've no lift. Will 1200 degree RTV applied suffice? You feel Home Depot's bolts to be high enough quality? How does a newb know? Thanks

@klowny1969

6 жыл бұрын

Spencer Field i would just readjust everything and clamp it down..home depot bolts are good

Hi there, what is the name or reference the Milwaukee tool. Good video.

@klowny1969

7 жыл бұрын

Julian Rojas the 3/8 ratchet?

@coltm4a1ops

6 жыл бұрын

the m12 1/4 impact?

I knew it was a ford focus the second I saw the wheels

@klowny1969

Жыл бұрын

Lol yup!

Any way to do maintenance to that part, like spray wd40 or other thing?

@klowny1969

2 жыл бұрын

Nope

2.30 to 2.40 tap the bitch like she owes me some money jaja pricelesss,,, love it...

he said farts, butter sause and nuts! lol

Can flex pipe be part of the header? And if so do you habe to replace whole thing?

@klowny1969

3 жыл бұрын

You can cut it off and replace it..Thanks for watching and don't forget to subscribe

@itachiswish4705

3 жыл бұрын

@@klowny1969 thx for info, would most auto shops have flex pipes laying around or you have to order it?

Will a bad flex pipe make a loud noise only when u start the car and accelerate that's what my exhaust is doing.

@klowny1969

2 жыл бұрын

it could be numerous other things as well..you need to identify where the noise is coming from..dont forget to subscribe

I was the 400 & 20th like I'm so proud

@klowny1969

6 жыл бұрын

Buzz Green Thank u so much!!

“Tap the bitch like she owes me money “ 😂

I just did a similar Job on my car and at the gaskets I don’t feel air coming from the area but there is a bit of water drip is this normal ???

@klowny1969

3 жыл бұрын

condensation..wouldnt worry about it too much if you dont see air coming out

@IDKWHYIDOTHISSHIT

3 жыл бұрын

@@klowny1969 cool thanks

❤Save 400 US.

@klowny1969

2 ай бұрын

Glad i was able to help..don't forget to subscribe 😉

What happened between 6:33-6:39 with your finger?

@klowny1969

7 жыл бұрын

rj jenkins had a little accident

Ah, so this is what an $1,100 dollar repair job looks like.

@klowny1969

6 жыл бұрын

ZombiZohm its a peice of cake to do yourself

@itsnotbleach

5 жыл бұрын

They want to charge me 1300

the only thing this video tought me is that i need a fucking air hammer asap

Yeah like my ol lady would be doing this repair or any repair herself LMAO!!!! I'd be one rough looking lady 😂😂😂😂😂😂😂😝😝😝😝😝😝 thanks for showing the part where you had to use vice grip pliers instead of doing it off camera and playing it off like it came right off with the box end wrench...that'd be the route I take because I doubt I have a bolt the same size laying around and I'd put it back on with the vice clamps too and make a note of it in my book of repairs

@klowny1969

3 жыл бұрын

Thanks for watching and don't forget to subscribe!

I wanna change the shocks in this 77 impala I picked up for $900. But afraid once I get em off can't get em back on.....cars in great shape but lots of rust on original bolts underneath etc. Been driving it in stock condition for over a year. thanks for the insight

@klowny1969

7 жыл бұрын

Kevi O easy to replace..cut nuts off if they are frozen..thanks for watching and commenting