Great video young man. Very meticulous of you which is a great thing. Keep it up and I wish you the best. God bless.

The nut on top of the main injection pump next to the 3 fuel lines requires 8fl oz of 10w 30 oil every 50 hours to lube the pump.

You have no idea how much you have helped me. You gave me the information I been searching for. Im now a subscriber.

Good job! Your fluid is nasty due to water in your system. Replacing those seals surly will help keep water out. In had algae in my hydraulic tank once, the fluid looked a lot like yours but chunky.

Great how-to, thanks for showing all the part numbers..

Thanks for this video! i have the same issues with my 3 pt hitch. Mine is bouncy too. I have already changed the fluid and filter but still had an issue. I did not know about the seal on the piston!

Thanks for the great video! There isn't anywhere else on forums or videos that I could find that shows the same problem! Thank you :)

Thank you for this video. I have a 1700 with no working hydraulic system. Thanks to you I have the new piston seal on and ready to assemble the top end .

Good video, I just picked up an old 1900 model and have already learned so much about it from your videos. Keep it up!

@averybryant

4 жыл бұрын

Thank you!

@beunbad

3 жыл бұрын

How are these old Ford tractors? I have a chance to pick up a 1220.

Well done.

Just replaced that seal with the help of this video. Thank you! That seal was NOT easy to get on.

That was a good repair gob. It lifted well after

Awesome video. I think the next video should be replacing that seat.😂🤣 Jk

@averybryant

4 жыл бұрын

Hahaha I completely agree. Maybe sometime soon. Thanks for watching

Great video just backwards on what's at hand. The whole system apart Inspection of all, clean all. Put together.

Thank you very much for the video!!!

Thanks for a great video it is very helpful

I am so satisfied to see it works again, great job bro, I will get a Ford 2000 soon, this is very useful, thanks man.

@anthonyr5869

Жыл бұрын

Did you do this on your 2110 ?

Very helpful video. I liked and subscribed.

@averybryant

3 жыл бұрын

Thank you

Great video

Good info!

Amazing job :O !!!

Just curious where you bought your dipstick for the transmission. I’ve seen a few different ones but I decided just to order the fill cap/plug. Had to chisel the old one out bc it seized up. But I’ve got the original shibaura sd2200 which is the same tractor basically.

Thanks for the video it helps a lot. Can you tell if the hydraulic oil has to be Exactly on the mark To be able to run the 3 Point and the front motor. And I have a nineteen twenty Ford and I can't get the PTO to engage.

You replacing that stabilization chain with a bar or leaving it as chain. Maybe a quick video on that.

Awesome 👍

How did you get cylinder liner off of valve assembly?

Great vid

@averybryant

3 жыл бұрын

Thank you

Did I miss the part where he checked the Flo to the pump? How does one go about that?

Great video. Sure wish it was a Massey Ferguson so it would help me a little more lol

That cylinder came with flat part down, but honestly it probably spins inside the cylinder overtime especially when you have a non functioning cracked seal

Where did you order the new seal for the piston and what is the part number? Great video.

@averybryant

3 жыл бұрын

Messicks.com I cant remember the part number at the moment but you can look up the one specific to your machine on that site

Another good vid!!! One thing I noticed is that our 1910 has the other gear shift on the tree not both on the deck..... were there different versions of the diesel 1910? Great to see her working so well!!!!! Thanks!

@averybryant

4 жыл бұрын

There sure was! They had all kinds of options for these tractors back in the dah. Ive found a lot of the different options when looking for parts on messicks.com. Thanks for the support!

Hi hoping you see my comments, I having problem with my shibaura SP1540 . It can lift slow at the start and after the temperature rise it wont lift the implement. What shoul I do. I used SAE 10W for the hydraulic oil and filter is cleaned. any suggestions to this thanks

Looking for video of ford 1910 axle seal replacement

Hey I have a Ford 1910 where did you get your pinston seal mines doing the same thing I know it’s gotta be shot like yours?

@averybryant

3 жыл бұрын

I ordered mine from messicks.com they have our fords listed under the new holland section

U the goat

Thanks. I am having problems with my 1700's lift. It is making a whining type sound when I try to raise the lift arms. Do you think this could be the issue?

@averybryant

2 жыл бұрын

It very well could be, never know for sure until you start checking things out for sure though. Plus a basic service definitely cant hurt

Great video, I have the same tractor and was wondering what type of hydraulic fluid you used? I buy most all my parts from the New Holland dealer, because they are local, but the Hydraulic fluid they recommend is almost $100.00 for 5 gallons! I was looking for a less expensive alternative, but still quality oil.

@averybryant

4 жыл бұрын

Thanks for watching! I used the Traveller Brand in the black bucket from Tractor supply. Its just called Universal Tractor Trans/Hydraulic Fluid. As far as other brands as long as it meets the ford 134 requirements you should be fine

@crpth1

3 жыл бұрын

@@JNHEscapes - For goodness sake! For "test" or troubleshooting purposes you could use olive oil, sun flower oil, engine oil and a vast etc. Keep that in mind and the credit card quiet in your wallet. LOL 😂

you all might be aware the owners manual on the 2110 says to put oil in the injector pump when you change the engine oil.dont know why unless the injector pump gets oil from the engine? the 1910 and 2110 are very similar machines. there is a plug in top of the pump you put the oil in . but it doesnt say how much.

@averybryant

3 жыл бұрын

That is true, only some models capped for it, the 1910 did not but if you manual says to do it then you should. They do get their oil from the engine.

Might want to replace that seat

I have the same issue. Can you tell me where to find the seal and other parts. I just bought a 1710. Thank you.

@averybryant

4 жыл бұрын

I bought mine off ebay but it was the only one on there. Messicks.com has everything you will need including parts diagrams. Thanks for watching

12:00 does that sound like a rod knock?

any chance i could message you or call you about some questions on my tractor? im lost

Have a 1320 I'll try this it should be the same I think

Where can I order these parts? 17 10

👏🍻👍

Great video. I just bought a Long 320. From the research if done so far is it's a Ford knockoff. My three point is not working as well. I found this videos and was wondering if anyone knows anything about the long tractors. I drained the fluid and it was milky which tells me it probably had water in it. The only filter I found was in the power steering reservoir. I would also like to know if there is a piston seal I need to check. Any help would be greatly appreciated.

@averybryant

4 жыл бұрын

See if you can find a parts diagram for the hydraulic system on your tractor. Some models have a screen at the start of the return tube that gets plugged up. Thanks for watching

Dude that seat.....

@averybryant

3 жыл бұрын

Got to make do sometimes hahaha. Ill change it soon

You need to put a new Seat

@averybryant

3 жыл бұрын

Nahh its fineeee

GH

U need to order a new seat

that's my bf

@averybryant

4 жыл бұрын

Same

i know him

@averybryant

4 жыл бұрын

No wayyy

Do not use WD-40 on any seal. WD-40 was designed as an industrial solvent to clean industrial machinery and parts, it will, if left on any type of rubber, plastic, or petroleum based seal and not completely cleaned off it will destroy your new seal and you’ll be right back at it again. Just a PSA.

@averybryant

2 жыл бұрын

Thanks for the tip. So far its held up fine, I suppose the hydraulic oil probably “washed” it off from the seal

@reedhryals7007

Жыл бұрын

It's for water displacement that's what the wd stands for

@mattfleming86

Жыл бұрын

It's not as aggressive as some folks make it out to be.. but it is still not great to use general purpose. It degrades stuff, and in presence of oxygen it turns into sticky varnish. For hydraulics, use a dab of hydraulic oil. Mixing anything with hydraulic oils, even mixing different grades/specs CAN cause problems, especially in setups that have a transmission attached. I wouldnt want to put wd anywhere in my trans case for that reason. not worth losing a detergent package over.

Great Video on hydraulics repair! I have a Ford 3910 and did a video on maintenance on it. If you can, check it out and please subscribe. Thanks, CUBMANCAN

The poor baby needs some annual care, take care of your tools so that they can serve you better....

@averybryant

2 жыл бұрын

This was actually a project I had picked up a while back to fix up and use. It is still working hard for me and gets regular maintenance now

Boo that's zoow....nowsey

i//s he available for adoption