I have to put put a new clutch on my MS461. You answered all the questions I had. Now it's my turn. Thanks a million for these instructions.

Very clear and concise instructions, easy to understand and follow along. You have a new subscriber. Thanks!

Excellent video.Like the impact drill hack to remove clutch.Look forward to more of these.Thank you

@chainsawshack2642

3 жыл бұрын

Thankyou. I’m glad you liked it.

Well done video! Thank you for being thorough. Do not let negative nasty comments deter you. Just delete. Thanks from Texas

@chainsawshack2642

2 жыл бұрын

Thankyou. I'm kind of sensitive to this stuff. I'm not trying to make money - just to share tips. Your support means a lot.

@jonp.6131

2 жыл бұрын

@@chainsawshack2642 Keep up the good work! I have a Dolmar 6100 saw that, I suspect, needs a new clutch and this video helped immensely. Cheers from America

@chainsawshack2642

2 жыл бұрын

@@jonp.6131 Hi Jon. Doing the videos was a lockdown experiment for me. It’s great to hear when it’s been helpful for someone. Thanks for the feedback. Andy

Great info, very helpful! Thanks!

Kia ora Excellent video. I like your easy to follow style without all the excessive waffle in american videos. I intend to carry out a check on the clutch of my Shindawa tomorrow as it does not seem to be working correctly. Kia kaha

@chainsawshack2642

2 жыл бұрын

Many thanks for your kind words.

Thanks so much ! Love your content brother! Would to see a maintenance video or some tricks and tips on gaining power

@chainsawshack2642

2 жыл бұрын

Thankyou. I do a lot of maintenance teaching - I just need another lockdown to give me time to do some more videos!

Superb! Really struggled to hear what you were saying, what I heard I thought was very important.

Thanks for doing this video, very helpful

@chainsawshack2642

2 жыл бұрын

Good to hear it was useful. Thanks

Thank you very useful information.

I tighten the clutch with my impact tight enough to get the E clip on the end of the crank. If you do not get the sprocket connected to the arm on the worm gear, you will not be able to get the E clip on the end of the crank. Stihl’s Service Manual says to rotate the sprocket one full turn to make sure it is engaged in the worm gear’s arm. I usually just put the sprocket on and rotate it a full turn and watch for it to drop down on the worm gear. Then, I put the washer and E clip on. I use a pair of kitchen pliers to snap the E clip in place. You should hear it snap into place. If not, replace it because it has lots its tension. They are pretty cheap at your Stihl dealer. It is better to replace it than have it come off while you are cutting.

Thanks, and God bless you!

Stihl company,please give this man one year supply of free beer.😄Absolutely superb presentation ,just like my old man.🍻🍻

@chainsawshack2642

2 жыл бұрын

Thankyou. I'm hope it helps.

Great video! Thanks mate!

Well done. Thoroughly and carefully shown and explained.

@chainsawshack2642

3 жыл бұрын

Thankyou. I was considering stopping doing videos due to unfriendly comments so it’s great to have good feedback.

@scatoutdebutter

3 жыл бұрын

@@chainsawshack2642 Unless the criticism is constructive or valid, then those people are to be pitied and ignored, right? :) Also, there is a wide range of audiences out here even among those of us who are sincere "watchers" -- e.g. from total beginner to "expert" -- and some of us conceitedly imagine any video we decide to watch should be all about "us" and exactly what we want to see at the moment, and so when a video fails to meet those unreasonable expectations we feel offended and the more stupid and immature among us react with an angry/mean, etc. comment! .... which is well to ignore! :) (and for what it's worth) ... along with good content, among other things, it does take (it appears) much patience and perseverance to build an audience in this medium. Anyway, best regards, sir, and keep up the good work!

@andybakewell1286

3 жыл бұрын

@@scatoutdebutter Thanks. I guess you take the risk when you participate in social media. I appreciate your support.

@chainsawshack2642

2 жыл бұрын

@@scatoutdebutter Thankyou. This means a lot.

@kaylas4132

Жыл бұрын

Yes very well. Thank you!

Great job. I think you put the big washer before the clutch wrong side tho.

Awesome video ❤🪓🌲

excellent video, wish y ou had more videos.

I just hit the clutch with my impact containing the righ size socket turning CW. As soon as it loosens, I spin it off by hand. The best way to take the old springs out is with a pair of needle nose pliers. With the clutch in a vise. I usually use oem clutch springs. 9:26

Great video! I take you eliminated idle screw setting as the cause first? It looks like the clutch was the problem though.

@chainsawshack2642

2 жыл бұрын

Yes, but it's a good point. I'd rebuilt the engine with a 100cc Hyway rebuild kit so it's certainly a possibility that this is a factor. Don't buy saws unseen from ebay is the lesson from this one!

Husqvarna suspernders and stihl chainsaw 👍awsome video thank you for sharing

@chainsawshack2642

2 жыл бұрын

No worries! Regarding the mix and match branding, when people ask, I always say that it depends much more on the model of saw than the make. Both Husqvarna and Stihl have made some truly terrible saws, and some great ones. The best saw for reliability, balance and all-round likeability for me is the Husqvarna 346xp. I still haven't found a saw I like more for small scale forestry work. As for suspenders (this means something a bit different in the UK!), oh well, I guess I am a lumberjack!

@danielpadgett2831

2 жыл бұрын

@@chainsawshack2642 yes sir I understand and greetings from alabama sir

@chainsawshack2642

2 жыл бұрын

And greetings to you from Wales, UK.

Nice video

Stihl recommends rotating the sprocket 360 degrees to insure the worm gear arm engages with the notch in the sprocket. If you cannot get the E clip on the end of the crank, your worm gear arm is probably not engaged in the notch on the sprocket or you did not tighten the clutch sufficiently. I usually put my clutch on with my impact and give it at least one rap with the impact.

Good stuff.

@chainsawshack2642

2 жыл бұрын

Thanks🙂

Thankyou

I got a farm boss stihl and my clutch seized up what u think ima see when I open er up ?

@chainsawshack2642

2 жыл бұрын

Very likely it will be a broken spring. You should replace them all because if one has broken the others will be close to breaking as well. Good luck.

I have ms180 she start fine but in the wood chain stop but chainsaw working fine.can be problem clutch or

@chainsawshack2642

2 жыл бұрын

The ms180 is a small saw and needs treating gently. The chain will stop in the wood when the chain is sharp and you have lots of teeth engaged with the wood (i.e. when you are cutting a large piece). Make sure you keep the engine revs high by not pushing too hard to get through the wood. The harder you push, the more load there is on the engine and the more likely it is that the chain will stop. With a plastic bodied saw like the ms180, if you carry on revving when the chain is stopped in the wood, you have a chance of overheating the clutch and melting the body of the saw.

I fix ‘em - I replace them. Putting new springs can be a hassle. I only replace the springs if I cannot get a new clutch in short order.

Where can i buy the stihl brand return spring for the clutch of chainsaw?

@KillingForFaith

Жыл бұрын

Only available through a stihl authorized dealer

Why not engage the clutch lock to keep the clutch from moving?

👍

So I have a stihl 026 that has the metal oil pump and plastic worm for some reason every single time the clutch over tightens when I put it on and go to pull the string causing it to not be able to turn over would anyone have any ideas on this

@andybakewell1286

4 ай бұрын

Two possible things. 1) check you didn’t put the big black washer on back to front. Note in the video I got it wrong first time then corrected myself. 2) make sure you pick up the oil pump drive arm with the notch in the clutch drum when reassembling.

That’s the wrong sprocket washer for a rimless sprocket. The aluminum washer goes on with a spur sprocket. You need the thicker steel washer with a rimless sprocket.

Gud video and use full speak

@chainsawshack2642

2 жыл бұрын

Thankyou

C clip, known as a Jesus clip, because when you took it off you said - where the .Jesus did it go? I have lost more of these than any other part on a chainsaw.