Tell him it's 12.7mm not 12.5 ;)

@thetallcarpenter

6 ай бұрын

I suspect you will be the first of many to correctly point out this Mark👊Cheers Del

@paulknights1764

6 ай бұрын

Always clean your hole out , before you put your bolt in … 😂😂😂 and a couple of pumps away ..

@thetallcarpenter

6 ай бұрын

@@paulknights1764 Not you as well Paul😲🤪

@paulknights1764

6 ай бұрын

@@thetallcarpenter couldn’t resist del .. 😆..

@RyanBrown-87

6 ай бұрын

I was waiting for someone to correct me 😂

Great video Del. Its a good tip to put your nuts on before cutting the threaded bar, saves any mishaps from ruined threads.👍🏻

@thetallcarpenter

6 ай бұрын

That's a great tip Lee👊Thanks for watching bud 😎 Cheers

👍 always like the problem solving discussions

@thetallcarpenter

25 күн бұрын

It's good to get the brain going Adrian👍Cheers Del

Great to see you posting another video. Understand why you cut down though. Still don’t know how you find the time when you are going all out to finish the job. I certainly don’t seem to have a minute to spare at the moment. Thanks 👍

@thetallcarpenter

6 ай бұрын

Hi Iain🖐It does take up a lot of my time, but I think I've found a fairly happy balance now, and try to get a couple of videos out a month🤞Thanks for your great comment and for watching 🤩Cheers Del

Brilliant great to watch atop class tradesman be great to spend aday with you have a wonderful Xmas

@thetallcarpenter

6 ай бұрын

Hi Trevor🖐Your too kind with your comment bud🤗and I hope you also have a great Christmas 🎄 Cheers

Great video! I was looking to setup resin anchors and this does a great job of explaining

@thetallcarpenter

5 ай бұрын

I'm glad the video helped🤩Thanks for watching 😎 Cheers Del

Love jobs like this, in the dry, loads of room to work and having the crack. Nice one👍

@thetallcarpenter

6 ай бұрын

Hi there🖐Absolutely bud, and I was actually looking forward to this job as I knew it would be hassle free and a giggle🤩Thanks for watching 😎 Cheers Del

Great to have you back Del 👏

@thetallcarpenter

6 ай бұрын

Appreciate your comment Jarrod🤗Thanks for watching 😎 Cheers

Well done Del nice to get in for the bad weather 🇮🇪☘️👍👋 , Always remember keep your nozzle clean 🤪🫣

@thetallcarpenter

6 ай бұрын

My goodness John, Ryan is the king of the double entundre🤪Thanks for watching bud 😎 Cheers

Ona a job a while back using chem fixing when we ran out and needed to go and get some more. Store had run out of the brand we were using so got a different brand. Half filled a hole with the last bit of the first brand and then filled hole up with some of the new stuff. And then the 2 reacted creating a gas cloud that instantly filled the work area and we couldn't breather and with eyes streaming ran out of the room. And we were working in a secure facility and got an almighty rollocking for that, a proper one. Don't mix your chemicals fella's.

@thetallcarpenter

6 ай бұрын

That sounds well iffy bud😬and definitely something to be aware of when using resin👍Thanks for your comment and for watching 😎 Cheers Del

@tilerman

6 ай бұрын

Very amateurish on our part, considering we'd filled out a COSHH sheet. Seriously, the smell was off the chart, really choking. Learned a lesson from the ear bashing we got!

absolutely loved the video, can’t wait for part 2!!!!

@thetallcarpenter

6 ай бұрын

Thank for your kind comment Peter🤗and part 2 is out soon👍Cheers Del

Nice one Del. Good to see you pushing on. That Ryan's a bit of a lad, eh? 😀

@thetallcarpenter

6 ай бұрын

Hi Matt, hope you are well🤞Ryan is a really good guy with great energy👊Thanks for watching 😎 Cheers

Good stuff! Can’t wait for part 2👍

@thetallcarpenter

6 ай бұрын

Thanks for watching 😎 and part 2 coming soon🤩Cheers Del

Great video, as usual. Looking forward to round 2.

@thetallcarpenter

6 ай бұрын

Appreciate your comment and thanks for watching 😎 Cheers Del

"you taking the piss?"......."Grand Fromage". Oh the banter.😅😅

@thetallcarpenter

6 ай бұрын

First swear EVER on my channel John😬 I really couldn't put most of the banter in as Ryan is not particularly 'PC'🤪Thanks for watching 😎 Cheers Del

@johnmackay7789

6 ай бұрын

At one point I was expecting Kenneth Williams and Sid James to appear. 😂

@thetallcarpenter

6 ай бұрын

@@johnmackay7789 😲🤩

Great video Del !!! thank you !!!!!

@thetallcarpenter

6 ай бұрын

Thanks for watching Michael 😎 Cheers

Great to see you back

@thetallcarpenter

6 ай бұрын

Thank Paul👊

Nice job in the dry. And a bit less cold. I agree a good job to do. Pretty simple work. Satisfying job. And for a mate. Perfect. We are cooking in high 30's heat. And the first Cyclone of the season is currently hitting Qld as a category 2. Doing a fair bit of damage as it tracks inland towards the Daintree. End of this week we should get the fall out. Some much needed rain. Different world.

@thetallcarpenter

6 ай бұрын

Hi Dave🖐Sounds like it's a bit full down there bud, and I actually think too hot is worse than too cold🤔 Thanks for watching fella🤩

Awesome job Del, always enjoy watching your vids mate

@thetallcarpenter

6 ай бұрын

Well I appreciate you watching🤩and thanks for your kind comment 😎 Cheers Del

Love it Del 👏👏

@thetallcarpenter

6 ай бұрын

Cheers Mark🤩

Filth Del ! Pure filth 🤣🤣. Sorry we missed you lot down I’m leam. Have a great Christmas Del 🎅🏽🎄😍🤜🏽🤛🏽

@thetallcarpenter

6 ай бұрын

I cut most of it out Steve😵‍💫Yeah, it was a shame we didn't get together😬Hope you also have a restful break over Christmas 👍Cheers

A great bit of work there Del. You soon got it whipped up . You can get a cone like cutter that fits in your drill and fits over the threaded rod to changer the end .👍👍

@thetallcarpenter

6 ай бұрын

I know the cone bit you're talking about John, and REALLY must get one for next time👊Thanks for watching 😎 Cheers

Fantastic channel. ❤

@thetallcarpenter

6 ай бұрын

Thank you Mark🤩Cheers Del

Always nice to see you Del and it looks likes a good project for this time of year. Great tip in how you managed to straighten out that ledger. A tip I have for you is next time on a similar job, before cutting your bolts thread the nuts on first just behind the length needed and it will save you deburring the ends, especially 40 bolts. Looking forward to part 2 but if thats all for 2023 thanks for all the videos and happy xmas to you and your family. 👏👏👏

@thetallcarpenter

6 ай бұрын

That's a great tip Kevin 👍 I just need to make sure I actually have some nuts next time🤪 Many thanks for your best wishes and hope you too have a nice Christmas 🎄 Cheers

Love the unintentional innuendos

@thetallcarpenter

6 ай бұрын

I had to edit most of them out bud😲Thanks for watching 😎 Cheers Del

Great video del 👍

@thetallcarpenter

6 ай бұрын

Cheers Joe🤗Thanks for watching 😎

Outside winter is a killer!

@thetallcarpenter

6 ай бұрын

You know it bud💦💨🥶

push it in as far as we can.. give it a couple of pumps and hopefully everyones happy 🤣🤣🤣🤣 you can tell you two are mates like. good craic when jobs are like that. just as a minor point. i found that toolstation sell short sections of threaded bar for this sort of thing which maybe wirth a look in future

@thetallcarpenter

6 ай бұрын

Hi Paul🖐hope you are well bud🤞Yeah, I do enjoy working with Ryan, it's always fun🤪I'll check out the short resin rods at toolstation 👊Thanks for watching 😎 Cheers

Quality video Del; that looks a nice project and those are some quality looking timbers (apart from the bowed one!). The resin part made me chuckle; looks like you got it in "bolts" deep, right up to the nuts!

@thetallcarpenter

6 ай бұрын

Honest bud, Ryan is just a inappropriate comment machine, and it took all my editing skills to keep the video from being X rated😆Thanks for watching 😎 Cheers Del

Having worked in the mud whole week i am looking forward building something similar next month, think slightly smaller but its in a heated space. Impressive progress, if you are alome it gennerally takes 3 times longer. Cheers!

@thetallcarpenter

6 ай бұрын

Working outside in the mud is no fun Tom😢 and you're right about things taking longer on your own🙃Cheers

👍👍👍.Thank you

@thetallcarpenter

6 ай бұрын

My pleasure 🙏 Thanks for watching 😎 Cheers

Neat project

@thetallcarpenter

6 ай бұрын

Appreciate your comment 🙏 and thanks for watching 😎 Cheers Del

Nice work, I recommend the Makita caulking gun battery powered! Very easy to use and you don't have to squeeze at all

@thetallcarpenter

6 ай бұрын

Checking out right now👊Thanks for watching 😎 Cheers Del

Double top plate to carry the load .

@thetallcarpenter

6 ай бұрын

Hi there🖐It's double tacked with 18mm osb so no need👍Thanks for watching 😎 Cheers Del

@kiwigrunt330

6 ай бұрын

And it is 6x2. Plenty strong enough.

@thetallcarpenter

6 ай бұрын

@@kiwigrunt330 💪

Top vid

@thetallcarpenter

6 ай бұрын

Cheers Joe🤩Thanks for watching 😎

As per 👏🏻👏🏻👏🏻👏🏻

@thetallcarpenter

6 ай бұрын

Appreciate you watching Alistair 🤩

Well Del . A laser is handy for this job. How did we manage before them 😅. I am a little jealous you been able to mark the studs were the laser hit, while standing 😂. I would need a steps 🙄🤣. Great video. 👍 🇮🇪

@thetallcarpenter

6 ай бұрын

Hi Paul🖐To be fair, the joists are only 2.2 meters off the floor, so not much of a stretch for most people👍And yes, it's crazy how much easier laser levels have made the game👊Thanks for watching 😎 Cheers

@paulcloona9331

6 ай бұрын

@@thetallcarpenter I only started using laser in the last 2 years. A game changer .as you rightly say. 👍

@kiwigrunt330

6 ай бұрын

@@thetallcarpenter That is a low ceiling for a carpentry workshop. Even for a not-so-tall carpenter. Too low to swing a full sheet around, let alone a cat. On lasers, I was compelled to buy an expensive rotary laser level 20 years ago to set out a new house on a steep site by myself. A dumpy level and a five metre stick clamped to a saw stool just didn't cut it. I earned the laser level back on that job alone. I just recently bought a cheap 3/360 laser level with receiver from Aliexpress. It is fantastic and remarkably accurate. How long it will last is of course another matter...

@thetallcarpenter

6 ай бұрын

@@kiwigrunt330 I actually described it as a workshop by mistake, and it's only offices and storage downstairs and showroom upstairs😬

What a great job for the winter. Was that compressor out of a travel fridge? The external deburring tools are great for thread ends.

@thetallcarpenter

6 ай бұрын

Sure is Michael👊Every time I'm grinding the sharp edges off threaded rod, I remember how much I need to get one of those deburring bits👍Thanks for watching 😎 Cheers Del

It's a veritable minefield of double entres! 😂

@thetallcarpenter

6 ай бұрын

He was a nightmare TN😵‍💫 I gave saying, 'I'm just going to push it in' 🤪Thanks for watching bud 😎 Cheers

@TheToolnut

6 ай бұрын

@@thetallcarpenter 👍💪🔨🇮🇪

You should try using thunderbolts Del. No need for resin and rod any more. M12 thunderbolt abd you just drill a 10mm hole and drive it in. Saves loads of time.

@thetallcarpenter

6 ай бұрын

Hi there🖐I will check them out as I've never heard of them👍Cheers

@kiwigrunt330

6 ай бұрын

Yeah, they are a game changer. I use them from 6mm and up. I find 6x80s fantastic for pinning down partition bottom plates.

@thetallcarpenter

6 ай бұрын

@kiwigrunt330 I've checked them out, and actually used some today for fixing an aluminium gazebo down into a concrete base👍Bloody brilliant 👏

@hendrax5889

6 ай бұрын

@@thetallcarpenter Bosh!! 👊

Love your vids pal really well explained and simple to follow . I’m sure you’ll have done a review or vid on it before but what’s the laser level your using on this ?? Keep up the good work 👍

@thetallcarpenter

6 ай бұрын

www.powertoolworld.co.uk/dewalt-dce088d1r-gb-12v-xr-cross-line-red-laser-level-kit-inc-1x-2-0ah-battery?gad_source=1&gclid=Cj0KCQiA4NWrBhD-ARIsAFCKwWsYQakIuvqVosQjklp0a6NFHPAUvcli7taeZa66_BBtNxvZKAOrkV0aAu87EALw_wcB This is the one in the video👍Appreciate your comment and thanks for watching 😎 Cheers Del

Don’t get too many stud walls like that. I like the the idea of marking off the studs to the laser! I would have built frame work on the deck to the tightest measurement and stood it up then wedge it up to the laser! I prefer your method🎉

@thetallcarpenter

6 ай бұрын

Using the laser was particularly suited to working indoors, plus it was a fairly low top plate👍Appreciate your comment and thanks for watching😎Cheers

Great video. I really enjoy your channel. Tell the smart arse at the beginning, 1/2 “ is actually 12.7mm if he wants to be pedantic…haha!!

@thetallcarpenter

6 ай бұрын

He's been told Charles🙃Thanks for watching 😎 Cheers Del

hi del long time no see ........this job is very interesting i love a new project where you can get your teeth into , no doubt as always its going to be another pukka job cant wait for the second episode

@thetallcarpenter

6 ай бұрын

Hi Stevie🖐You're right bud, jobs like this are great cause you can get stuck in👊Part 2 coming soon🤞Cheers

Del, you forgot to tell the jokers..."Hey, I'm trying to make a video here!"

@thetallcarpenter

6 ай бұрын

I told him many times bud😬but it made no difference🤪Thanks for watching 😎 Cheers

👍

@thetallcarpenter

6 ай бұрын

Thanks for watching Paddy 😎

👌

@thetallcarpenter

6 ай бұрын

Thanks for watching James 😎Cheers Del

Forgive me Del, I'm laughing now...I only just realized it's just one joker!

@thetallcarpenter

6 ай бұрын

He goofs around enough for two bud😆

Ryan aka Sid James!👍

@thetallcarpenter

6 ай бұрын

Absolutely SPOT ON Maurice😆

Are you putting a vision panel in the internal wall or door as you have created a room within a room in terms of fire regulation compliance?

@thetallcarpenter

6 ай бұрын

Hi there🖐There will be 2 doors through the center wall, both will be glazed fire doors and be hung according to the fire escape route👍Thanks for watching 😎 Cheers Del

Another great video Del, joisting out a space like this is always a glory job as it changes instantly, looking forward to the next video. Did you consider a double top plate for the stud wall? Cheers, Will.

@thetallcarpenter

6 ай бұрын

Hi Will🖐We didn't go for a double top plate purely because there is 18mm osb screwed on both sides of the wall👍Thanks for watching and your comment 😎 Cheers Del

Hey, where do you stand on 15 vs 16g nailers? I've got a 18g and framer, but wondering what to buy next.

@thetallcarpenter

6 ай бұрын

Hi there🖐I've had 18, 16 and 15g nailers and found that the 15g was good but only used for a few specialist applications. I now only use the 18g for finer work and the 16g for more 2nd fix carpentry jobs👍Cheers Del

Would you use M8 or M10 Fischer frame fixings for a 40mm x 70mm door frame, door is around 35kg

@thetallcarpenter

6 ай бұрын

I would use M8x100's 👍

What laser are you using? Del

@thetallcarpenter

6 ай бұрын

Hi there🖐 It's this one👍www.powertoolworld.co.uk/dewalt-dce088d1r-gb-12v-xr-cross-line-red-laser-level-kit-inc-1x-2-0ah-battery?gad_source=1&gclid=Cj0KCQiA4NWrBhD-ARIsAFCKwWsYQakIuvqVosQjklp0a6NFHPAUvcli7taeZa66_BBtNxvZKAOrkV0aAu87EALw_wcB

@pureblood1415

6 ай бұрын

@@thetallcarpenter cheers Del

👊🫡

@thetallcarpenter

6 ай бұрын

Cheers Richard🤗

How's the ribs

@thetallcarpenter

6 ай бұрын

Still quite sore Neil😬but much, much better thank you🤗Cheers

Grownups 🤪😂

@thetallcarpenter

6 ай бұрын

I used the term loosely bud😆

Obviously you have building regs & fire on what your doing

@thetallcarpenter

6 ай бұрын

Hi there🖐Yes, this is all done in strict adherence to the commercial regs for both fire and structure👍Cheers Del