Superb ! I really enjoy doing a FG knot following the Ultimate channel technique, but I will enjoy this one too !

@pescadorestamora

Ай бұрын

Thank you, friend ☺

Great tutorials on fg knots and variations. Thanks

@pescadorestamora

3 ай бұрын

You're welcome

Good video. Nicely filmed all in close up so you can see exactly what’s being done.

@pescadorestamora

Ай бұрын

Thank you 🙏

Most of my fishing is for bass, so forgive me for asking a question related to scaling down the line size. Although I typically tie an FG, my question applies to both the PR and the FG. In order to make the knot smoother when reeling through guides, level winds, and to prevent the knot from “catching” other coils of line on the reel when casting, I typically tighten the main knot after one or two half hitches, add another 5-10 half hitches over both mainline and leader, then trim the leader and apply the Rizutto on the braid only. I can't think of any reason this would result in a weaker knot, but I'm curious if you think it might. Thanks.

@pescadorestamora

2 ай бұрын

sir, the knot as you said, putting Rizzuto on the braided line will not make it weak and the knot will make your line smoother. Please correct me if I'm wrong sir 🙏

Great tutorial - thank you 👍

@pescadorestamora

2 ай бұрын

You're welcome

I like this knot buddy

@pescadorestamora

3 ай бұрын

Me too 😁

I am going to start listening to this music when i am rigging. Very soothing

@pescadorestamora

5 ай бұрын

Wow, this music is very calming, isn't it?

This looks so much easier than the regular FG. This will be the way I tie it from now on.

@pescadorestamora

17 күн бұрын

☺

PR knot tied without a bobbin. Great knot for just about everything that swims.

@pescadorestamora

Ай бұрын

You have to try it buddy

@Sam-xn7zp

Ай бұрын

@@pescadorestamora yep it is a good knot. It takes a bit longer to master without the bobbin.

@pescadorestamora

Ай бұрын

@@Sam-xn7zp good luck ☺

A hybrid between tony pena/ hand wrapped PR and alternating half hitches withe the rizzuto finish. Surely a very good knot in my opinion

@pescadorestamora

2 ай бұрын

try it bro

@dante7228

2 ай бұрын

@@pescadorestamora I don't think I will, FG works fine for me

@pescadorestamora

2 ай бұрын

😁👍

Some humble thoughts... 1) I'd say the strengh should be the same a the fg knot. Based on the physics, both knots use to take a bite into the leader. 2) Because the fg is bound with both ends of the main line from the same side instead of coming from one side, turning and wrapping back, the bite into the leader might be even better than your version? But... with 20 wraps it shouldn't matter any more. ;-) 3) The last knot (a grinner?), I'd make it a little bit different. Here's how: instead of wrapping the knot around main line plus leader, I'd rather make it over main line only. Here's why: the connection between main and leader should be rock solid by the 20 wraps. These last overhand knots and the grinner should only be nessesary for securing the end of the main line. The grinner with main line only is slimmer than your version. It ads a step in diameter between main line and knot. So, the end of the leader is kinda hidden behind the grinner. I'd argue, it makes it easier to go through the top ring while reeling in the line. These kind of knots tend to be pretty stiff, so, it makes a difference. Just some thoughts. I really loved your video!

@pescadorestamora

4 ай бұрын

Thank you my friend, your explanation is very helpful for me

Thanks bro.... I can try this knot 🙏🙏🙏

@pescadorestamora

4 ай бұрын

You're welcome, and good luck

Wow, great turtorial mate!! Thanks for sharing!! 🤜🏼🤛🏼🎣💪🏼🎣

@pescadorestamora

5 ай бұрын

You're welcome. Thanks for watching ☺

@davids1314

3 ай бұрын

C du solide c sur mais, honnêtement je suis pas fan bcp trop long quand t au bord de l'eau !!!

@pescadorestamora

3 ай бұрын

@@davids1314 alors vous pouvez utiliser un nœud de pêche plus rapide. Comme le nœud Alberto ou Yucatan

Looks somewhat easier then the FG with all the wrapping around your fingers, standing on the line etc. Same result a good knot just seems a little easier Thanks

@pescadorestamora

5 ай бұрын

if you use a bobbin to weave into the leader line, this knot will be much easier 😁

@reefnreefer

4 ай бұрын

Cheers buddy!

@pescadorestamora

4 ай бұрын

😁🎣🎣

3 ай бұрын

Great tutorial, thank you. Sometimes my FGs slip off the Fluoro when I tightened so I am going to try this one.

@pescadorestamora

3 ай бұрын

You're welcome, then you should try this knot

Great knot, will give this a go. Question, When you go back 20 wraps, is it essential you stay right inbetween the previous made wraps or is it ok if some overlap the braid from the first 20 wraps? Ta

@pescadorestamora

3 ай бұрын

It should be possible, because in the last 20 wraps after you finish with the first lock, you will pull it into a smooth braid like I did in the video. but if you repeatedly overlap the nodes, it will make it difficult for you to pull out the first lock. hope it can be understood 🙏

It can't be stronger than the FG knot, because it's a FG knot ! Just the technique is different. Thanks for sharing it.

@pescadorestamora

5 ай бұрын

You're welcome, actually this is a PR knot, but made without using a bobbin

@pescadorestamora

4 ай бұрын

thank you, please tell me what kind of concept I should review

@snappyvalleyfishing

4 ай бұрын

@@pescadorestamoraI was going to say this is a PR knot. I use an FG on most of my rigs except my heavy jigging set where I use 80lb braid and 100lb leader - this is when I use the PR knot.

@pescadorestamora

4 ай бұрын

@@snappyvalleyfishing Tell me bro, so what type of knot do you think this is? 😁🙏

@snappyvalleyfishing

4 ай бұрын

@@pescadorestamora I would say it is a PR knot. Typically though, a PR would have 30 winds. (IMHO). Like I say, I only use this on my heavy jjgging set up.

I’m curious as to how this can be stronger than the FG, when it’s essentially the same thing except it’s merely wrapped/overlapped, while the FG is braided by alternating the legs of the braid. I’ll stick with the FG.

@pescadorestamora

2 ай бұрын

😁👍

Thank you for the good technique.+1

@pescadorestamora

5 ай бұрын

You're welcome, good luck

Great knot. Have to try it.

@pescadorestamora

4 ай бұрын

You must try it 😁👋

I like this hibrid knot half Tony Pena and half FG… the only critical part in my opinion is the coconut oil that stays slippery while i would use saliva

@pescadorestamora

3 ай бұрын

And when sailing, I also use saliva to moisten the knot 😅

PR. Save yourself some effort & snug your wraps up tight to 1 another as you wrap (say every 10) then wrap them tightly taking your time on the return in the main line direction. Looks pretty good but I will stick with the fg. A tiny dot of super glue on the rizutto finish will lock it.

@pescadorestamora

25 күн бұрын

And I always use the Fg knot as well

@koogle612

16 күн бұрын

Love to see a connection knot for mono to fluoro other than the surgeon knot. Thx.

@pescadorestamora

16 күн бұрын

😁👍

Anyone know how this would compare to a PR done with a bobbin with that extra tension?

@pescadorestamora

Ай бұрын

obviously stronger if tied with a bobbin

I know this knot is amazing! And I love the art of it. But I can confidently say, I will never take the time it takes to make this lol. I’d do all that and then just get snapped off by a barracuda or get snagged and be pissed. 😂😂

@pescadorestamora

4 ай бұрын

Because it takes longer to make than alberto knot

Another thing is if you tie the FG right you have no need to tie 100 half hitches after 2 will be plenty, I’ve used the FG for 35 years and never once has it came undone with only 2 half hitches

@pescadorestamora

17 күн бұрын

👍

Nice job!

@pescadorestamora

2 ай бұрын

Thank you

Alberto or Albright, but without doubling over the leader. Interesting.

@pescadorestamora

4 ай бұрын

This is a PR knot and not an albright or alberto 😊

This is new to me. What tests were done to show it is stronger than FG? Just curious. Thanks

@pescadorestamora

2 ай бұрын

The leader line grips more firmly than the main line

@lucky4meyeah

2 ай бұрын

It's a pr bobin knot without the bobin it's been tested many times and the out come has always been stronger than the fg knot you can find many test video on KZread

Can this be used to tie two different thicknesses of braid like thicker braided leader to thinner main line braid??

@pescadorestamora

5 ай бұрын

I hesitate to say, because I've never tried it. But I recommend that you use the Alberto knot to make braid-to-braid braids and I have used the Alberto knot and the results are good. Next video I will make a tutorial

@gavinlangford2984

5 ай бұрын

@@pescadorestamora So the Alberto knot is the strongerst braid to braid connection?? What about the slim beauty??

@pescadorestamora

5 ай бұрын

@@gavinlangford2984 I only recommend alberto, because I use it. As for fineness, I think it can be used for UL 6-15lbs fishing rods

@frederikmare9002

5 ай бұрын

Yes the PR knot is very effective for joining braid of different thicknesses. This knot is known as the PR knot and is indeed stronger than the FG knot. It is usually tied with a special bobbin.

@pescadorestamora

5 ай бұрын

Agreed, but if you don't have a bobbin, a PR knot can also be made without a bobbin

There is no way this is stronger than an FG knot. Countless break tests have been done comparing this and an fg knot and the fg always wins. Always.

@pescadorestamora

Күн бұрын

That is true 😅

PR knot done without a bobbin. PR>FG nice video

@pescadorestamora

4 ай бұрын

Thank you. you can also see the PR knot using a sinker

@asmadiahmad8606

2 ай бұрын

Yes Sir I also use this PR knot on my pe8 popping set. But this video without bobbin... I using bobbin for the tightening the bridded winding at leader...

@pescadorestamora

2 ай бұрын

The best

طريقة جيدة لأننا نتفادى بها راس النايلون المعكوس الذي يرتطم مع الحلقات عند الرمي. شكرا

@pescadorestamora

2 ай бұрын

You're welcome ☺

Rizzuto ตกปลาบ่อยๆ เงื่อนมันคลายออก มีวิธีแก้ไขไหมครับ

@pescadorestamora

Ай бұрын

You should add a half hitch a few twists, then pull to tighten the braid, and finally finish with Rizzuto. this way the knot won't slip

How do you guys lock your rizzuto? My rizzuto always starts to unravel after a few casts.

@pescadorestamora

3 ай бұрын

You can see directly how I tie the rizzuto lock in the video. I always end the rizzuto lock at the end of the Fg, PR and Sc knots. And it never unravels

👍good nice

@pescadorestamora

2 ай бұрын

😊👍

Top demais amigo

@pescadorestamora

3 ай бұрын

você deveria tentar amigo

I only use peanut oil for my knots.

@pescadorestamora

2 ай бұрын

👍

salam hadir dari indonesia kepulauan aru maluku

@pescadorestamora

27 күн бұрын

Salam juga bosku ☺

@benskai2475akurfishing

27 күн бұрын

@@pescadorestamora terimkasi senior ilmunya untuk memperbaiki kesalahan saya sering nyangkut di ringnya ternya gini caranya mantap sekali senior

It’s the exact same thing as the FG knot just different way to tie it ! So definitely not stronger than an FG like the guy before my message said because it is the FG!

@pescadorestamora

17 күн бұрын

😁

Can yah make a video for light leader line like 2-6lb? All theses type of knots like these will snap needing to pull soo hard to synch..

@pescadorestamora

4 ай бұрын

If you tie it properly with a knot like this, it won't slip. I myself use it for a 3-6lb fishing rod.

@expansioniskeyrn

4 ай бұрын

It doesn’t slip. The line itself snaps when pulling to make it tight.

@pescadorestamora

4 ай бұрын

sorry, I just understood what you said. what you mean is, let me try making a video with a 2-6lb leader line, is that correct?

@expansioniskeyrn

4 ай бұрын

Yes please 😊

@pescadorestamora

4 ай бұрын

Next video 👍

It really look sp strong

@pescadorestamora

3 ай бұрын

It's really strong, sir, I've tried it

It is a PR knot. Done without the tool. With some dodgy wrapping, more half hitches than you need and a good resutto finish. Takes too long. The school has moved off. But thanks for the show.

@pescadorestamora

5 ай бұрын

Thank you again. this is indeed a PR knot and I made it without a bobbin because I don't have one. So I made it in a simple way and just used my hands 😁

@ThatGuy-sw2xe

2 ай бұрын

What idiot starts tying on his leader when the fish arrive? Do it on shore and be ready.

So an FG with coconut oil?

@pescadorestamora

5 ай бұрын

I don't use oil for the FG nodes. But for the PR knot I use it to be smoother when pulling the braid

Tuna Knot?

@pescadorestamora

19 күн бұрын

PR knot

No coconut oil ty...

@pescadorestamora

3 ай бұрын

That's right, just using saliva will do the trick

buy a bobinknot asist von shimano make it more faster stronger and easier...

@pescadorestamora

5 ай бұрын

I do not have the funds to purchase it 😅.. So I am using whatever I have

It's a bit ridiculous. I don't have ten minutes to make a knot. I'm sticking with the Carrot knot.

@pescadorestamora

3 ай бұрын

😅

Imagine wasting 10 minutes to tie a knot on a charter boat, rocking back and forth while the fishing is hot? Yeah, gimme a swivel hommie.

@pescadorestamora

2 ай бұрын

😅

@pescadorestamora

2 ай бұрын

😅👍

@ThatGuy-sw2xe

2 ай бұрын

Do it right before you leave and you won’t have to do it again on the boat.

@sigspearthumb1056

25 күн бұрын

@@ThatGuy-sw2xethat’s what I’m saying who would wanna do this on a boat yea it can be done but my stuff is always rigged up and ready the night before so I don’t have to waist any time when I get there and I always tie on a good amount so I can wind it on my reel a couple cranks so even if the bottom end breaks I still won’t have re tie the leader knot I just tie back on whatever rig I’m using or switch to.

Effectively tied an FG knot with 20 loose wraps

@pescadorestamora

4 ай бұрын

👍👍

@gabrielduarte3904

4 ай бұрын

that is a pr bobbin knot W/O the bobbin and less wraps.. so i doubt it will hold more than a well done fg

@pescadorestamora

4 ай бұрын

@@gabrielduarte3904 👍👍

Get yourself some sharp scissors

@pescadorestamora

4 ай бұрын

OK sir, I have sharpened these scissors to be sharper

By the time I'm done with this knot tide has done a full cycle

@pescadorestamora

Ай бұрын

😅

@BladeIntoOblivion

Ай бұрын

@@pescadorestamora it looks like a very strong knot tho and streamlined too. I might try it one day, might.

@pescadorestamora

Ай бұрын

@@BladeIntoOblivion please try it bro 👍

👏👏

@pescadorestamora

24 күн бұрын

👋👋

It takes too long to tie The FG knot is easer

@pescadorestamora

3 ай бұрын

Thank u 👍

Keren bang

@pescadorestamora

2 ай бұрын

😁👍

Fg for me tie a fg inside a few minutes

@pescadorestamora

2 ай бұрын

👍

Knot stronger than the FG knot!

@pescadorestamora

4 ай бұрын

Yes, this is a PR knot

где-то спряталась третья рука, которая держит моно справа

@pescadorestamora

23 күн бұрын

не руки, а ноги. Я завязала моно на большом пальце, чтобы было легче заворачивать.

@michaelemelyanov5199

23 күн бұрын

@@pescadorestamora а можете посоветовать узел для тонких шнуров? типа 0.06 + флюр 0.12 чтобы можно было вязать почти вслепую, внатяг, на весу в ветер с фонарем. что не пробую - все рвется как труха, завязывается один узел из пяти, времени и нервов уходит вагон

@pescadorestamora

23 күн бұрын

@@michaelemelyanov5199 с тонкой леской того размера, который вы сказали, я всегда использую узел Альберто или Юкатан.

You need to get yourself a pair of ridgemonkey braid cutters, they are excellent. Got 2 different pairs of what your using both shite for cutting braid

@pescadorestamora

Ай бұрын

Maybe in the future I will buy it

Nightmare knot😮

@pescadorestamora

2 ай бұрын

😅

All of these impractical knots. Like most things there is a point of diminishing returns with these knots. Its like, sure it my be a strong knot, but how long does it take you to tie it and can you tie it on a bass boat in 1.5 foot roller with wind blowing 15 mph? Good luck! Great demonstration video, but no thank you. Im a bass angle, and Im not going to invest 10 minutes in tying a freaking leader knot, and even more time if the conditions are rough.

@pescadorestamora

Ай бұрын

Thank you for watching and commenting sir. If in the situation as you said, I also would not tie it like this. Maybe I would prefer to tie it with an alberto or yucatan knot which I think is easier and faster. So more precisely to tie I look more at the situation and conditions when going fishing 😁🎣

@sigspearthumb1056

25 күн бұрын

Why not just tie the leader on at home and tie it to a length where if you loose your rig you still have a nice amount of leader tied on so you can just retie a hook or whatever you use. The knot is strong enough that it shouldn’t break from normal use unless it’s not ties properly and even then I’d bet your line would break off at your hook and jig or whatever you use. I always tie about 6 or 7 feet of leader on. And then tie on whatever rig I’m gonna use. That’s why it’s also called a wind on leader. Not to mention you also get the benefit of having a almost invisible leader line under what’re for them finesse fishing on soft biting fish

any knot is strong if u do it correctly

@pescadorestamora

4 ай бұрын

Thank you for your advice, sir.

👍🏻👍🏻👍🏻very good 🙏🏻🙏🏻มารับชมเติมกำลังใจ❤ +1 ❤ให้กันครับ😊

@pescadorestamora

Ай бұрын

Thank u ☺

SC knot process

@pescadorestamora

4 ай бұрын

Many say this is a PR knot

@KingPogsit

4 ай бұрын

@@pescadorestamora exactly.. a pr knot master..

@pescadorestamora

4 ай бұрын

True, you should try this one knot

i ain’t got time for an 8 minute knot

@pescadorestamora

4 ай бұрын

It only takes 1 minute to tie this knot, if indeed really tie it

@skippt2

3 ай бұрын

It's actually a knot you tie prior typically, if you break off you've learnt to tie it in a way that doesn't teach others. Otherwise, you're right a basic knot might take you 8 minutes, who am I to judge your abilities.

So what's the point of using braided line if you just going to tie a fluorocarbon to it I mean it's just not making any sense to me

@pescadorestamora

Ай бұрын

The function of the leader line is as a damper when the fish suddenly fights back. The illustration is the same as the use of shock absorbers on motor vehicles. Casting without using a leader line will feel less comfortable, it will feel rough when striking, not smooth.

@sigspearthumb1056

25 күн бұрын

Main reason people use braid is because it’s way stronger for the diameter of the line itself. Say you have 20Lb mono or Floro you coil use like 40 or 50lb braid for the same diameter of line meaning you get stronger line for less diameter. If you reel holds 250 yards for 20Lb mono test you could have 450 or 500 yards of line if you used a light strength braid say like 30lb braid. Not exact numbers just demonstrating the difference. Another reason people use a Floro leader while having a braid main line is because braid has absolutely no stretch and mono and Floro do have stretch. Also for a shock leader when casting super heavy wait as soon as the braid tightens when casting heavy weight it juts snaps and pops your line. When mono or Floro would give some buffer and strech. And also because Floro line is almost invisible under water.

@swimpsmagbayao9513

25 күн бұрын

@@sigspearthumb1056 wow okay that's a great response I'll buy that I just retired and getting into fishing thanks for the info

@sigspearthumb1056

25 күн бұрын

@@swimpsmagbayao9513 NP another tip when throwing heavy weight and I’m talking like 5ozs and up you need 10ths for every oz thrown for your shock leader and the shock leader needs to have a couple turns into the reel like 6 or 7 turns of line onto your spool and again 10lbs of line for ever 1oz of weight thrown. This is usually done for surf fishing but I also do it when bank fishing for sturgeon on the Columbia river in Oregon and Washington

@threesixasrael7554

23 күн бұрын

😂😂😂because you have no idea buddy😂

The time you waste doing this "embroidery" is done by making two throws with a simpler knot

@pescadorestamora

Ай бұрын

I am sorry 🙏😅

@joeywinters3061

13 күн бұрын

This knot is meant to be reeled through the guides on the road and be a long term thing so you can have a topshot or 20ft leader material and cast it through

@pescadorestamora

13 күн бұрын

👍

But we'll done

@pescadorestamora

4 ай бұрын

👍

Wow, spend all day tying, not fishing, then you forget the coconut oil, and the whole day is shot.

@pescadorestamora

4 ай бұрын

🤣✌

no thanks. too long, too much effort.

@pescadorestamora

5 ай бұрын

😁

You lost me at coconut oil! And yes, this is basically a FG knot with a risutto.

@pescadorestamora

22 күн бұрын

you can use saliva

Still FG knot but done by each side. It takes more time than normal FG knot. Imagine when you have to do it at the fishing site .... do it then you will see the difference.

@pescadorestamora

5 ай бұрын

Most people say this is a PR knot without a bobbin

@befmx31

4 ай бұрын

Shoot, I can't imagine tying a FG out on the boat. I can tie the FG. Not a pro but I can tie one.

@pescadorestamora

4 ай бұрын

There's an easier way to tie the Fg, you can tie a braided line to knob reel. You can find it on my channel 🙏

@sigspearthumb1056

25 күн бұрын

Or you could do what like everyone else does and tie up the night before so you don’t have waist time when you get out on the water.

Not an FG , that looks like a bobb8n knot without the bobbin

@pescadorestamora

5 ай бұрын

This is not an Fg knot, sir, many say this is a PR knot without bobbins

Way to long, gotta be done in 60 seconds max. Imo

@pescadorestamora

4 ай бұрын

Actually this is quite fast, but if I make a video quickly. Can other friends follow it?

@georgeweiss2137

4 ай бұрын

@@pescadorestamora why wouldnt they.???

@pescadorestamora

4 ай бұрын

If you watch a fast video, you will definitely get very confused

@theodgracia1281

4 ай бұрын

@@pescadorestamorathere's 3 option video speed

uni knot would be easier.

@pescadorestamora

4 ай бұрын

If you use a 60lb leader line, it will be difficult to use the uni knot.

@johnnyjj2712

4 ай бұрын

@@pescadorestamora ok

@sigspearthumb1056

25 күн бұрын

Ya I don’t know anyone who would ever tie a uni knot for a wind on leader ever. Knot is to big and rough to repeatedly keep casting thru guides

PR knot, get yourself bobbin tool !

@pescadorestamora

Ай бұрын

😁👍

Ten minutes to do this

@pescadorestamora

5 ай бұрын

It should be faster, but if I make it faster. Can it be called a video tutorial? 🤔

It looks like PR knot without use of the tool.

@pescadorestamora

4 ай бұрын

Yes, this is a PR knot

@ouks5

4 ай бұрын

Well done

@pescadorestamora

4 ай бұрын

You can also see the video on making PR knots using sinkers on my channel

@ouks5

4 ай бұрын

Awesome, I'll check it out. Thanks

@pescadorestamora

4 ай бұрын

Thank you and nice to meet you. May you always be filled with happiness

HAHAHAHA!!!! Thats is still a FG KNOT... just being twisted from front to brack.... i got THUMB NAIL BAITED LOL

@pescadorestamora

3 ай бұрын

But many say this is a PR knot

@KantoBassTV

3 ай бұрын

@@pescadorestamora i can seee you agree it's still an FG knot, only a different way of tying it. lol

@pescadorestamora

3 ай бұрын

@@KantoBassTV 🤣

It can not be stronger than FG knot, i think.

@pescadorestamora

26 күн бұрын

maybe, but most people do strength tests and PR knots win against Fg knots

Coconut oil 😂😂😂😂😂😂😂😂😂😂😂 Just spit on it man

@pescadorestamora

3 ай бұрын

🤣Just use saliva, bro

Too long to do. I can almost ask the knot out on a date, coconut oil and all.

@pescadorestamora

3 ай бұрын

Actually, I use water from my mouth 😅

This is the same basic knot as the FG tied in a different way is all. It uses the same Chinese finger trap method and half hitches so the strength would be exactly the same! And its spelled "KNOT", not node dipstick. lol

@pescadorestamora

5 ай бұрын

Thank you for taking the trouble to scroll and provide criticism 😁

@dharmakusuma2560

5 ай бұрын

PR knot without bobbin❤❤❤

@sigspearthumb1056

25 күн бұрын

Does the uni knot and clinch knot have the exact same strength

9 mins......

@pescadorestamora

Ай бұрын

😀

Complicated than FG but not stronger.

@pescadorestamora

3 ай бұрын

😁

Its still fg so... 🤷

@pescadorestamora

4 ай бұрын

This is a PR knot without a bobbin

PR knot.... nothing new

@pescadorestamora

2 ай бұрын

😁

8min to tie this knot. No thanks

@pescadorestamora

5 ай бұрын

😂

@f1hook

5 ай бұрын

If he tied it any faster, you would be crying that you couldn't keep up 😂

@pescadorestamora

5 ай бұрын

sometimes I'm confused. If I tie it faster, can the video I make be called a video tutorial?

Zzzzzzz

@pescadorestamora

5 ай бұрын

☺☺😅

@at_tro_sizematters

5 ай бұрын

@@pescadorestamora it was a great video. I just wanted to be funny. Keep up the great work.

@pescadorestamora

5 ай бұрын

Thank you, sir 🙏

This guy is talking total BS.

@pescadorestamora

Ай бұрын

😁

FG knot more better

@pescadorestamora

5 ай бұрын

Ok 👍

@robertcox9226

5 ай бұрын

Wrong, that is the pr bobbin knot tied by hand stronger . Also there are many variants of the FG knot as low as 70%to as high as low 90% The GT knot for offshore size line is also very strong (doubled line ) not the copycat knot. Sc knot is faster than Fg and nearly as strong

@babefishing4921

5 ай бұрын

Still FG knot😎😎

@pescadorestamora

5 ай бұрын

You can see how I tie a PR knot using sinkers in my other video 😁

Ha ha same freaken knot fg

@pescadorestamora

2 ай бұрын

😅

This looks really good I’m just super scared for my bait caster 😰🫣

@pescadorestamora

Ай бұрын

don't be afraid, you have to try it 😁