FIRST START OF MY CHINESE 10 HP DIESEL !
Автокөліктер мен көлік құралдары
In this episode I work on getting my 10 hp ebay diesel running. I first start by hooking up the battery and key switch. After making sure it will turn over with the starter I work on priming the fuel system. After messing with the fuel petcock at the bottom of the tank to figure out which way is on and witch is off I finally got the system primed. The lawn mower battery wasn't cutting it so I hooked up one of my semi trucks battery and it cranked right up!
Пікірлер: 33
Nice!!! No more gummed up carbs from the corn sauce we run in the old kohlers! Good choice, Diesel is the way to go ! 👍👍
@dreamingbigcustoms9860
2 жыл бұрын
Oh yeah and no messing with fuel mixture screws
Diesel Power😈
Did you install the starter? If so what starter is compatible with this engine?
Where did you get the starter for that
What pulley did you use?
FINALLY SOMEONE ELSE WITH AN IDEA LIKE MINE!!! I'm wanting to put one of these on my John Deere 210!! And i want to remove the pullstarter, and instead have a huge ass flywheel to hand start it, like starting the 1940's john deere model A!!!
@texaspoontaper5813
2 жыл бұрын
I wanna do it to my 212 did you finish yours yet
@nascarsimracing1
2 жыл бұрын
@@texaspoontaper5813 i haven't done it yet, I'm sorry. Ive been having a ton of life drama, shit's been hell lately. I currently dont have time to work on the deere. Right now i gotta focus on keeping myself afloat.
@texaspoontaper5813
2 жыл бұрын
@@nascarsimracing1 more power to you man good luck
Hey nice build !
@dreamingbigcustoms9860
3 жыл бұрын
Thanks but it's not even close to done
@corndogextreme8887
2 жыл бұрын
@@dreamingbigcustoms9860 where did you get the engine?
@dreamingbigcustoms9860
2 жыл бұрын
@@corndogextreme8887 ebay
i had to shorten the battery cables.. cut into them to find 9o percent rubber 1 percent copper .. nice big looking cables tiny little wire inside . im gunna open up the starter motor ill be looking for a rubber band
Volume control on the next video would be nice...
Please music needs to go or it least lower vol. Nice project!
Did you import this motor? Or ?
@dreamingbigcustoms9860
2 жыл бұрын
Bought it on eBay but it definitely came from China
Why didn't you rotate the recoil to start from the seat
@dreamingbigcustoms9860
2 жыл бұрын
I'd like to see you pull that from the seat even with the compression release on it takes alot of strength to pull it over. If it was a 6 hp gas engine than I would have but no Way you are pulling that sitting down
@kidddogbites
Жыл бұрын
@@dreamingbigcustoms9860 You can, seen it done.
these are a 500 hour motor the Japanese one is a 3000 hour motor
@logenanderson5825
2 жыл бұрын
Where can you find a Japanese one?
@kodisteffes8699
Жыл бұрын
Got close to 2000 on mine it’s a Chinese clone engine like this bought it in 2007!
@jonnysnipes3123
Жыл бұрын
What happens when you get close to its end life, does the motor runaway and scream to the moon
@user-et7yp1ih1j
4 ай бұрын
Fucking china
@Waterboi-kd8bq
Ай бұрын
Lawn mower engines cost $2,000 and dont last that long😂
Diesels run at much lower rpms than gas.That would make everything like a mower deck turn much slower.
@williamfurniss6442
Жыл бұрын
Easily countered by fitting a bigger drive pulley
@Wingnut353
Ай бұрын
Old mowers like this often had a low speed Briggs 10hp or something like that on them, in other words its already fine.
not the best idea to have all that exhaust blowing into your face , extend it with a flexible heat resistant pipe.
@thewobblywelder8362
Жыл бұрын
Like an ‘exhaust’ pipe?