First Flight: INAV 6 FPV Freewing L-39 Albatros 80mm EDF Jet Takes to the Skies!
Ойын-сауық
Join your boy on my maiden flight with my customized FPV - Freewing L39 Albatross EDF jet. Equipped with a DJI O3 digital FPV system, a reliable Matek-743 flight controller, a TBS Crossfire receiver for long-range control, and a BN 880 GPS for precise navigation. I've also added some custom 3D printed parts to improve cooling and airflow, and Motion RC provided some top-quality interior 3d designs so we don't have to (It's on their website).
Using FDM printed parts until I print them in resin and paint. Still deciding on if I like the camera placement.
Пікірлер: 18
Great flight! and great angle from the camera view! 👍
I'm about to Maiden my L-39 also in FPV... great flight.. Watching this has given me confidence.
@AntoniusBlack01
Жыл бұрын
That's great to hear!! This baby flies like a Cadillac
I'd say it is good maiden. Your camera placement is fine and I think it resembles the actual cockpit view of someone piloting the actual Albatros. I can't help but ask man - that mAh reading on the left side right bellow the speed reading can't be true, right? An 80mm freewing edf (that is in case you fly stock setup) that runs on 6 cell should consume more than a 1000mAh in three or so minutes, which was the duration of your flight. I would suggest throwing some shortened throws on the aileron and elevator, as well as pleeeenty of expo in order to smooth out that bumpy ride my man. Set low rates and expo's, test fly without fpv and confirm that settings are sufficient and smooth enough. Throw some sort of flight stabilization on it too for further improvement in flight comfort. Last but not least if I was you I would dedicate a whole flight to confirming the stall speed of the plane experimenting at heights of about 400ft. Once stall speed is confirmed you're gonna be allot more confident in that landing approach. All in all great footage and I thank you for it my guy. I especially enjoyed how the airframe vibrates in tight loaded turns. That's wicked.
Great flight with that fpv , very impressive, what's the fpv set up ? Where to get it from ?
@AntoniusBlack01
Жыл бұрын
DJI O3 digital FPV system, a reliable Matek-743 flight controller, a TBS Crossfire receiver
Great flying! Love your minimalistic OSD. Which flight controller are you using?
@AntoniusBlack01
Жыл бұрын
Matek-743
@motionsic
Жыл бұрын
@@AntoniusBlack01 with INAV 6?
@AntoniusBlack01
Жыл бұрын
@@motionsic yes
Looks good. How much trouble is it to remove windscreen ?. I want to detail my cockpit
I also love my L39 and plan to fly her FPV, but must first begin to know how to deal with my new Speedybee F405 Wing and INAV on simple airplane...already have flown FPV my 90 EDF Viper with DJI O3 with simple autopilot, but must have an OSD now with INAV! the problem is : I have no recorded OSD when playing the SD card on DJI goggles V2, only when flying! Do you have the stock canopy? the view is very clear through!
@AntoniusBlack01
8 ай бұрын
Working on a video today I will show you what I used for the windscreen.
@alainrac56
8 ай бұрын
@@AntoniusBlack01 can't wait for yout canopy, thanks! an other question if you don't mind, I use also a Crossfire nano connected to my F405 fc and can't have the channel 7 of my TX16s active on the fc pins for a pan servo...as you have a pan servo working, do you also use the same Rx?
@AntoniusBlack01
8 ай бұрын
I use elrs now@@alainrac56
@alainrac56
7 ай бұрын
@@AntoniusBlack01 I have pan cam on ch7, and use 10ch of 12, I can move the cam manually, but surprisingly, with the headtracker "on", all servos are jamed, while it works correctly on my Funjet! Got the + from the ESC direct to the landing gear to avoid to have too much amps for the FC, but on the bench, I have an overheat message...in the 80 EDF L39, I dont exceed 90A!
man, I have this exact plane and radio, what rx are you using by chance?
@AntoniusBlack01
Жыл бұрын
Crossfire