This dude is a legend. 4x4 swap in 3 days, are you kidding? What a legend..

@bradynbrown41

3 жыл бұрын

Not only 3 days . But laying on the ground 🤘🏻 epic

@Beandiptheredneck

3 жыл бұрын

Just gotta want it. It’s really not that hard, I dropped and swapped my trans, auto for manual in one day, drove it home that night, that was all laying on the ground too

@austinbales9168

3 жыл бұрын

@@bradynbrown41 he says in a comment that he did it in 3 days total, 2 for the front and 1 for the back

@crispfn4605

3 жыл бұрын

@August Carl LMAO

@nachomoreno549

2 жыл бұрын

And in the rain

Truck looks great, I like that you spent the time to clean up and paint the parts as they went in.

@swidobros6437

3 жыл бұрын

Thanks! Little effort goes along way in the way the truck looks. also helps me identify potential problems down the road

Just went through this with my 1990 F150, however added a high pinion dana 44 SAS up front as part of the swap. Great work! If anyone is interested, I'd be happy to share the parts list.

@Juanrodriguez-zy4sy

3 жыл бұрын

I have a 93 f-150 2WD 5.0 V8 engine also thinking of swapping it to Dana 44 , I have 20x9 fuel vapors 5 lugs when I put the Dana 44 on will the lugs be the same for my rims to fit? I would like to see pictures from your project

@theoldmanofthenorth

3 жыл бұрын

@@Juanrodriguez-zy4sy Lug pattern will be the same. 5 on 5.5.

@Juanrodriguez-zy4sy

3 жыл бұрын

Thanks for replying, ok what years dana44 can I install in my front axle? Yours came from 96 bronco . And once I get the Dana 44 installed can I run it without the 4x4 transmission? I still gotta get that separate and did you had to get a new drive shaft once You got the 4X4 transmission ?

@theoldmanofthenorth

3 жыл бұрын

@@Juanrodriguez-zy4sy Oh, I'm not the person who owns this channel. I have just done this swap. I used a Dana 44 out of a 78' bronco. With that being said, any coil sprung dana 44 out of an f150 that ran the TTB should install without issue. Probably from 80 to 96 I would assume. You can run the truck with just the 4x4 front end until you come up with a transmission and transfer case. However, if you do a solid axle swap vs. the TTB dana 44, you'll need at least a 4 inch lift for everything to clear.

@michaelbeard6891

Жыл бұрын

Ok bro help me out lol I have a 1991 F150 Lariat XLT RWD 4.9 6 cylinder. I want to convert it to 4x4…

Sounds good, looks good! Seems pretty simple to swap axles and add the lift.

Been considering this for my old 7.3

That's awesome bro good job!!

Wow that looks so good. Dude great job!

nice job man, im fixing to do the same minus the 6 inch lift(for now) and i have a 5 speed. fortunately i have a car lift and a whole parts trucks ready.

Process just like i did with my 1980 f150. Used dana 44 front and 9in that was in truck. Also swapped out 351m and installed a 460. Rollerized the c6 that reduced parasitic losses by almost half. Will probly upgrade to d50 front axle and d60 rear in future to haul around my truck camper

@almulakimaalimalriadiat9068

Жыл бұрын

is your truck still running ? any issues?

Any recommendations? We got the same truck I been looking for a parts truck. How did you cut the 4L 4H shift knob Into the cab or what did you do? And we’re you able to get the 4x4 light to come on? Last question if I wanted to do a 4x4 swap from 2wd but also turn it into a manual from an automatic is it the same steps? Thanks and impressive job hope mine turns out good.

@TheRoadhammer379

Жыл бұрын

The hole for the 4x4 shifter is there, just a plate screwed down

Figured it would be a sas. Still looks awesome

Truck looks great ,, aswome job !!

I would love to have my old 91 F150 4x4 back. 300 CID inline 6. Thing could not be killed. Oh well couldn't get it to where i moved after I left Oregon.

It's beautiful beautiful beautiful

make an ordinary truck look bad ass, your good guy

Nice job bro

Taking those granpa skirts off instantly gave you 5 HP hahahah

Good shit, brother.

what brand those rims, I love them. I want like that on my 1992 flareside.

@saucytoon3452

Жыл бұрын

What mirrors you got on your flareside. I wanna covert the original memo morris to chrome tow mirrors

just takin the skirts off made it lo0ok taller

Awesome bro! Good job man.

Thanks for posting this.

So nothing about trans? Crossmember? Transfer case? Driveshaft? Electrical connections?

I have a 95 long bed six cynlinder two wheel. It is the 4.9 six cylinder. I would LOVE to convert to four wheel. Can you tell me, roughly, how much it cost you to make the conversion? And do you think it will be possible to make the conversion considering that my truck has a six cynlinder. I don’t want a lift on it. Just want to go to four wheel drive. Any advice you can give would be really helpful

@hunterlachance9369

2 жыл бұрын

I have the same truck, and I'm thinking about doing the same thing. I think it depends on where you live for the price (using junkyard/used parts). I might buy junker bronco as a donor truck for the project.

When can i drop off my truck you sir lmfao. Great job, looks great!

Im interested in seeing the transmission and transfer install. Come on bro your killing me.

@williammatney-tate5057

2 жыл бұрын

Just unbolt and rebolt

Badass

Nice job. Come to my house and install a lift on my 1993 flareside. I’ll pay you good money. Lol. I just don’t have the time.

Sweet... I want to do the same with my 95 F150 Eddie Bauer shortbed 2wd...

@RustyShackleford382

Жыл бұрын

Do IT!!

F150 with the small block gae I've got the f250xlt with the 460 and 4x4

did you go with the manual transfer case or the push button one, and if you chose the push button anything needed to be done with the pcm?

Bad ass truck

Nice swap but I think I would have used Solid straight axle in front.

@RustyShackleford382

Жыл бұрын

Prob didn't due to cost

What about steering stabilizer? Did it come with one?

I'm doing the same thing with my 95

How much did it cost u in all including the trans

@swidobros6437

3 жыл бұрын

Little over 2k

Classic.

Can u add a link to parts

Nice truck what do you do with a spoiler if you want to sell it I want to buy

If you still have it, I would be very interested to purchase the trim piece from you that you removed from the truck! $

The dislikes are the honda ridgeline owners

How did you get the 4x4 to work? Was it just locking the front hubs or did you instal a 4L4H shift knob? I want to do this to my 95 4.9L but not sure how it would work. Any advice?

@TheRoadhammer379

Жыл бұрын

Yes you have to install the friggin shifter for the 4x4 transfer case. If you are not knowledgeable in how the 4x4 works on these trucks, let someone else install it

So I need a 4x4 rear diff/axle in other for it? Or can I slip on front (4x4) axle and leave the 2wd rear and it should work?

@swidobros6437

2 жыл бұрын

If you can find a gear matching front axle. I just swapped the back out because I found the front and rear off the same truck. Made it easy

I wonder, how will you setup the electronic buttons for 4x4 and low range??

@TheRoadhammer379

Жыл бұрын

There is no button, it's a manual operated transfer case for the 4x4.

Did you have to find a shorter rear drive shaft?

How long did it take you ?

@swidobros6437

3 жыл бұрын

Did the front in 2 days and the back was another day .so three days total

Nice

Did you have to swap the rear axle or was it just for gear ratio purposes?

@swidobros6437

5 ай бұрын

It was for gear ratio !! To match the front gears.

@joshlarsen3603

5 ай бұрын

@swidobros6437 thank you, just picked my donor up last weekend

How much did the front axle Assembly and the transfer case run you?

@swidobros6437

Жыл бұрын

I bought all the parts off a parts bronco because the matching gears. I think I was into the front,rear axles and transfer case 600 bucks

Would this work for a non 4x4 twin I beam setup?

@swidobros6437

3 жыл бұрын

If you mean the lift? It comes in 2wd and 4wd but I think the 4wd version just has the add a leaf

@jakebeardsley473

3 жыл бұрын

@@swidobros6437 yeah that’s what i meant, so an axle swap isn’t necessary for the kit then

@swidobros6437

3 жыл бұрын

@@jakebeardsley473 no sir, I was planning both so just made more sense to do at the same time

@jakebeardsley473

3 жыл бұрын

@@swidobros6437 thanks for the info! I’ve got a 96 f350 dually. Might have to pull the trigger on this kit

Did you get the lift kit for the 2wd model or 4x4. Summit is giving me a difficult time

@swidobros6437

3 жыл бұрын

I bought the 4wd drive kit I orderered from rough country website

How long did it take you to do the front I have a 94 wanted to do this but it my only vehicle Should I try to find a use one while do the. 4x4 swap

@swidobros6437

3 жыл бұрын

It took me about three days start to finish. but even though this is my daily driver I have other vehicle's to drive while it was down I don't recommend doing the swap without back up transportation

@kaitlynrich5540

3 жыл бұрын

@@swidobros6437 thanks for the information I’m ona budget have a f150 I wanna fix more better. But at same time I rather another for the project and put mine back to original. It was one my dad me brought be her past it has over 300k but still runs trying to decide if I wanna keep this one original or do aftermarket or look for another one to play with Incase something go south

Didn't know you could make a truck 4wd

@austindyck5231

3 жыл бұрын

Huh?

@Beandiptheredneck

3 жыл бұрын

It’s the exact same frame as the 4x4, a few different brackets is the main thing there, then you’re just looking at putting the t case on, either get a 4x4 trans or get the right parts to convert the 2wd one to 4x4

@Poorboyzgarage447

3 жыл бұрын

A Ford you can chevy used a different frame for the 2we trucks

@Beandiptheredneck

3 жыл бұрын

@@Poorboyzgarage447 really? I know a guy who converted a c10 to a k10 but he also used 1 Ton axles so it may have been all custom stuff. What’s different about the frames?

@Poorboyzgarage447

3 жыл бұрын

@@Beandiptheredneck 88-98 the k series frames come down a little further than a 2wd also the front end isn't interchangeable the square body trucks you could easily convert

What size tires are those?

@swidobros6437

4 жыл бұрын

I'm running hankook 32x11.5 r15s on 15x10s

@fingergunsgaming3485

4 жыл бұрын

SwidoBros thanks

@nauidiver227

3 жыл бұрын

I put my 4 inch lift last Sunday. I had a slight rake and decided to use coil spacers up front to level it off. Great video I need to do the same

@davidobrian5623

3 жыл бұрын

Awesome build man I’m looking at doing the same to my truck

Stupid question. Is this doable with the 4.9?

@TheRoadhammer379

Жыл бұрын

Yes of course, what the hell does the engine have to do with a 4x4 conversion

Did you use same steering linkage? Can you?

@swidobros6437

2 жыл бұрын

yes

Do you use the same sway bar ?

@swidobros6437

3 жыл бұрын

No Used the one off the bronco

@adriancontreras3710

3 жыл бұрын

@@swidobros6437 Thank you I plan on doing this to my 1985 f150 pretty soon

Will the 96 bronco transmission fit a 96 f150 for the conversion

@swidobros6437

3 жыл бұрын

As long as it's the e4od 4x4 version you will need a matching ecm for engine tranny combo but yes

@jonhromeo6108

3 жыл бұрын

@@swidobros6437 so it be best to go with 4x4 f150 transmission to avoid that

@swidobros6437

3 жыл бұрын

You will need to get a new ecm either way 2wd won't control 4wd

@jonhromeo6108

3 жыл бұрын

@@swidobros6437 I see thanks

What size wheels are you running?

@swidobros6437

3 жыл бұрын

32 x11.5 x 15s

Would I be able to put a 4WD 4in lift on and RWD?

Do you know what wheels these are

@swidobros6437

3 жыл бұрын

There aluminum American racing 15x10s

Do you have a cam or muffler system

@swidobros6437

3 жыл бұрын

Gutted cats straight piped

@kaitlynrich5540

3 жыл бұрын

How did you gutt the cats My 95 is my only automobile and don’t wanna break the bolts in the manifolds

@swidobros6437

3 жыл бұрын

Cut the pipe behind the cat and hammer out with a pipe or rebar

What did you do for the transmission

@swidobros6437

3 жыл бұрын

Found a used e40d 4x4 and electronic transfer case

@Poorboyzgarage447

3 жыл бұрын

@@swidobros6437 did you get the bezel that had the buttons what all did you have to do to get that to work plus the 4x4 indicator light?

@swidobros6437

3 жыл бұрын

@@Poorboyzgarage447 the 4x4 indicator light is already present just got the 4x4 switch and cut bezel once you swap the ecm it's really all plug and play

@Poorboyzgarage447

3 жыл бұрын

@@swidobros6437 you have to have the computer out of a 4x4 truck right?

@swidobros6437

3 жыл бұрын

@@Poorboyzgarage447 yes

Just ruined ur vin # bye converting it..

@TheRoadhammer379

Жыл бұрын

who gives a f u k