Thank you! I just bought a $200 2017 txt bc it was stolen/recovered and wouldn’t move. Watched your video, jumped the ignition, and driving it

@HeyHeyHey97

3 жыл бұрын

K cool glad I could help

Thanks! For all the great information. Saved me money

@HeyHeyHey97

Жыл бұрын

Thanks for watching and the super thanks man!!!!!

thanks man you helped me.i owe u one

@HeyHeyHey97

2 жыл бұрын

Thanks for watching

Great channel. Glad I found this 👍

@HeyHeyHey97

Жыл бұрын

Glad it helped.

Thank you so much for the video it was a big help

@HeyHeyHey97

2 жыл бұрын

Thanks for watching. Hit the subscribe button. That way I know yall watching and will make more videos..

Great video great explanation

@HeyHeyHey97

Жыл бұрын

Appreciate the comment. Thanks for watching

Thank you sir that was the problem.

@HeyHeyHey97

2 жыл бұрын

Np. Subscribe please

Great job thanks

@HeyHeyHey97

2 жыл бұрын

Thanks for watching

Great video - thanks for posting it. I have a 2011 RXV 48v cart that just died tonight. I just put 4 T1275 Trojans in it. Drove it a half dozen times and it was fine. Took it about 1/4 mile and turned to a friends place it off. Went to take it back home an hour later and it won’t do a thing. Batteries showed 51v total. I turn the key to any position and get nothing.. Maybe key switch? I will try some of your trouble-shooting tips. Hope the controller isn’t fried.

@HeyHeyHey97

2 жыл бұрын

Try the charging port first. Follow what I done in video with the back of the wire from charger port. Do you have a reverse buzzer in reverse

@Twilight-Imagery

2 жыл бұрын

@@HeyHeyHey97 - will do! Oddly enough, it had just been on the charger before I took it on that short trip..

clutch video 🙏🏽

@HeyHeyHey97

2 жыл бұрын

More to come!

Great video. Thank you

@HeyHeyHey97

Жыл бұрын

Thanks for watching hope it helped

@duanebrown2879

Жыл бұрын

@@HeyHeyHey97 You're welcome. One inquiry, you reference and "ITS" in the video, what is an "ITS?" Thank you

@HeyHeyHey97

Жыл бұрын

@@duanebrown2879 inductive throttle sensor. It’s in the floorboard. It will cause the cart not to run and also int running

@HeyHeyHey97

Жыл бұрын

@@duanebrown2879 inductive throttle sensor. It’s in the floorboard. It will cause the cart not to run and also int running

Thank you for posting the video! It gave me a great work-around for the issue I was having (1st you mentioned - 'bypassing the circuit inside the charger plug.' Question: for a permanent fix, do I need to replace the charger receptacle or is the issue somewhere else in the electronics? I'm looking for a permanent fix because it seems I need to remove the bypass to get the charger to charge the batteries. Thank you.

@HeyHeyHey97

2 жыл бұрын

Yes change receptacle

@HeyHeyHey97

2 жыл бұрын

That's right so that's working.

@BexarPrepper

8 ай бұрын

I changed the receptical and it's still not working. What next?

@HeyHeyHey97

8 ай бұрын

Whenpu plug the charger in what does it do. Also what kind of charger do you have

@BexarPrepper

8 ай бұрын

@@HeyHeyHey97 nothing no click. I also purchased a new charger and still the same. Only get click when I jumped the wire from plug. Charge gauge on golf cart now registers 3/4 charge but won't move.

I have a 1989 easy go golf court and we give it gas and you can hear it like it’s running but it will not go forward or reverse any ideas on what’s wrong?

@HeyHeyHey97

3 жыл бұрын

Check your brake drum.

@HeyHeyHey97

3 жыл бұрын

They are splines were they go on your axle. And they are known for stripping.

Hi Christy, appreciate the video, I recently bought a dead EZGO TXT. Got it back home and found all 6 Trojan batteries to be dry (its a 36V cart). I took all the batteries out, cleaned them up and filled them with distilled water. I charged them all independently and re-installed in the cart. After a few charge cycles, the cart seems to be working and I've been using it for odd jobs about the place. However, the other day, I tried to use it with my (large friend) as a passenger and it stopped after a few feet. When he got out I was able to drive it again. Having not had one before, I'm not sure what it can and can't do, so i'm not sure whether this is indicative of the other issue I'm about to describe or whether I'm just asking too much of it. Also after this incident, I tried to use it a day or so later and even though the charger was reporting full battery, it would try to move but wouldn't. I thought the batteries were shot (even though they were measuring 37V) but today I kept depressing the throttle up and down and eventually the cart started to move and I was able to drive it around again.

@HeyHeyHey97

3 жыл бұрын

When it dont run. Does the sol. Click.

@healeydave

3 жыл бұрын

@@HeyHeyHey97 I think so, I just gave it another test run and it worked again, so can't say for sure. It's one led from the top of the 36V meter bar and its sluggish, especially on small inclines, which I know they struggle with at the best of times but this is really small which I believe it should cope with.

@HeyHeyHey97

3 жыл бұрын

@@healeydave how old are the batteries.

@HeyHeyHey97

3 жыл бұрын

@@healeydave do you have volt meter

@healeydave

3 жыл бұрын

@@HeyHeyHey97 pretty old I think

Good, Thanks!

@HeyHeyHey97

2 күн бұрын

Yes sir thanks for watching

Great video! I have TXT 48 and everything checked out as I followed your instructions, The cart is moving a little bit then it shudders, battery pack is at 50.3 and the batteries are 3 years old, Could this be the motor? Cart has lift and 23in tires, stock Curtis controller and motor is stock as well, has new solenoid, F/R switch, new ITS, And speed sensor in the motor, completely stumped on this one, Any ideas

@HeyHeyHey97

Жыл бұрын

Have you tested the batteries under a load. Meaning while you are driving it. Or put one tire up against a tree and rest each battery individually. As you hit gas. Don’t hold gas down too long. But probably motor. But check battery voltage first

@kpeezy86

Жыл бұрын

Had a cart that shuttered… brushes were bad. $20 fix diy

@HeyHeyHey97

Жыл бұрын

That right

Have txt 48 ezgo and just replaced all the batteries. Key switch on it says fully charged but will not nove in forward or reverse. Nothing happens when pedal is pushed down not even the reverse buzzer. All volts line up except the white and black plug wire show 3.8volts regardless of pedal being pushed down.

@HeyHeyHey97

Жыл бұрын

Did it run before you changed batteries

Hello again I have a 2013 ezgo rxv golf cart. Would a weak induction sensor affect the top speed ?

@HeyHeyHey97

Жыл бұрын

No. How fast is it going

@brentduncan2137

Жыл бұрын

@@HeyHeyHey97 it belongs to my son in law. I thought it was running fine. He thought after I replaced solenoid and pedal switch, it was running as fast. Not sure of mph

@brentduncan2137

Жыл бұрын

It wasn't running as fast

@HeyHeyHey97

Жыл бұрын

@@brentduncan2137 if the speed sensor was bad it wouldn’t run but 1 mph or would sit there and shake

@brentduncan2137

Жыл бұрын

@@HeyHeyHey97 ok. Thanks again

Excellent video..thank you! One question: Assuming everything else is good, if the ITS is bad will it cause the controller to keep from activating the solenoid when key switch, pedal switch, and FWD/Reverse are proper?

@HeyHeyHey97

2 жыл бұрын

What type of ezgo cart do you have.

@HeyHeyHey97

2 жыл бұрын

36 or 48 v

@gltandwlt

2 жыл бұрын

@@HeyHeyHey97 It's a 36V TXT PDS. I've checked all connections like I mentioned...the solenoid does not get an activation signal from the controller when everything is turned on and the pedal switch is activated. I'm thinking this means that the controller is bad. Would you agree or do you think it's possible an ITS failure would cause the controller to not activate the solenoid?

@HeyHeyHey97

2 жыл бұрын

@@gltandwlt have you checked any voltage.

@gltandwlt

2 жыл бұрын

@@HeyHeyHey97 Yes .. all voltages are as expected. However, I've not yet checked the white and black wires that go to the ITS.

I have a fleet of 48v TXT models and one of them will run in reverse but not forward. I have checked the forward and revers switch but it is fine. I've had issues with the inductive throttle sensor on some of my other carts but I feel like it wouldn't go forward or revers if that was the issue. A year or so ago this particular cart had a few nicked wires in the wiring harness where it runs through the frame on the underside of the cart. I cut and spliced the wires back together and this solved the problem. Since I don't do this everyday I forgot what method I used to troubleshoot this problem. I remember jumping a wire from somewhere but I can't remember exactly how I did it. Any ideas?

@HeyHeyHey97

2 жыл бұрын

I would flip the wires on the f n r switch. And see if it runs forward and not reverse. If it does then you know its switch if it don't its probably a wire. Do that test and let me know what you find and will tell you next text.

@brianwright6306

2 жыл бұрын

@@HeyHeyHey97 Thanks for replying! I already tried that and still only runs in reverse. Crazy thing I just went out and checked it and it ran in forward and reverse but it will eventually die out in forward.

@HeyHeyHey97

2 жыл бұрын

@@brianwright6306 check your battery voltage in forward it runs off full battery pack and in reverse halve

@HeyHeyHey97

2 жыл бұрын

@@brianwright6306 get you a volt meter and check the forward wire at the controller to make sure its getting g the proper voltage

Thanks for the great video. 2013 TXT 48v. Cart won’t move and reverse alarm doesn’t work. I also have no power to the white or black wires with key on, green reads 50v. Will the ITS also make the reverse alarm not work? Or is it possibly the F/R switch? Also tried bypassing the Reed Switch and have good key power to solenoid yellow.

@HeyHeyHey97

Жыл бұрын

No the it’s will just make the cart not run

@fullcircletms5813

Жыл бұрын

@@HeyHeyHey97 Hmmm, I don't have any voltage to either the black or white wires as described in the video. Is it possible that the issue is the FnR switch? Not sure how to test the switch.

@HeyHeyHey97

Жыл бұрын

If every other voltage checks fine and no voltage on black or white. Bad controller

@fullcircletms5813

Жыл бұрын

@@HeyHeyHey97 that's what I was afraid of. Thanks for your help.

What causes not having voltage from the black wire coming from the floorboard the white red and green have voltage.

@HeyHeyHey97

3 ай бұрын

A bad it’s in the floor board. (Inductive throttle sensor)

@HeyHeyHey97

3 ай бұрын

Thanks for watching. Anymore questions let me know. Hit that like button for me

36v ezgo txtpds. No solenoid click. Tested everything in the video and all is fine EXCEPT no voltage on the white wire of the ITS. I have 36v on the red and between green and red but nothing on white or black. Will this stop the solenoid from clicking? Also the cart has a XCT48400-PDS controller. Should the status light be on?

@HeyHeyHey97

11 ай бұрын

Yes will stop the sol clicking

@EGGINFOOLS

11 ай бұрын

@@HeyHeyHey97 ok thanks. Im subbing to you. Your videos are straight to the point and accurate

@HeyHeyHey97

11 ай бұрын

@@EGGINFOOLS I just make videos of how I would want to watch a video. Some of them drag the topic on to long

Sir I really appreciate your video. I tried a few of the things you suggested and almost had my cart fixed. I'm sure you're a busy man but I was hoping you could help me diagnose an issue. I just installed new batteries in my golf cart and it will not move. The solenoid does not click. Batteries are fully charged. I jumped the red wire from the charging port to my main battery and for the first time my battery light came on. Thinking this was the issue I threw an eye connector on it and was going to test it out but after connecting it with the eye connector the battery light no longer comes on and the cart still does not move. I do have reverse beep. It's a 2000 E-Z-Go txt series. I have 42.2 volts at the red charging wire and both micro switches. I'm not sure how anything could be bad because all I did was replace the batteries. If you have any suggestions I would greatly appreciate it.

@HeyHeyHey97

11 ай бұрын

Did it run before changing batteries. your cart is 36 volt right? Check main pos and main neg to make sure you have wired correctly. How many wires do you have on main pos and main neg

@pcbisnice

11 ай бұрын

I have it wired in series

@HeyHeyHey97

11 ай бұрын

You have 42 volts is that while it’s charging?

@pcbisnice

11 ай бұрын

@@HeyHeyHey97 lithium batteries

@pcbisnice

11 ай бұрын

@@HeyHeyHey97 each lithium battery is 13.8 volts which adds up to a little over 41 volts

Is there a way to check my charger to insure it acually Chargers.? Because I charged all my batteries individually so the cart had enough power to run around in. But I still can't get my charger to charge the batteries.

@HeyHeyHey97

Ай бұрын

What type of charger do you have and what type of cart

@HeyHeyHey97

Ай бұрын

Do you have a volt meter

Great video Would be great to see one on 2000 txt 36v with same complaint. I tried your test on mine, and it doesn't have main battery voltage at solenoid(yellow wire) with key switch on. All key switch wiring has continuity. and check for 36 volts at key switch nothing on white or white yellow. Also nothing where those wires come out of controller. I'm hoping it isn't controller. Hoping I just missed my off ramp. If you have any feed back it would be appreciated. Broke down in Vegas

@HeyHeyHey97

3 жыл бұрын

Jump a wire from the main positive on battery pack to yellow wire on sol. Small post. And see if cart runs.

@HeyHeyHey97

3 жыл бұрын

Subscribe to my channel.

@henrystuckrath2701

3 жыл бұрын

@@HeyHeyHey97 Did that nothing

@henrystuckrath2701

3 жыл бұрын

@@HeyHeyHey97 Christy your video is best I've seen on You Tube Some of these guys are just plain dangerous I have subscribed take care

@HeyHeyHey97

3 жыл бұрын

Do you have volt meter

I have a txt48 that will not go. The solenoid just clicks on and off real fast when given gas but doesn't move. I've changed the controller, solenoid, and its and it still does the same thing. I've given the solenoid voltage straight from the battery and still won't go. Could it be a bad wire harness?

@HeyHeyHey97

Жыл бұрын

What does battery voltage show. Normally when that happens the controller is bad. Have you tested the motor to make sure it’s good. And yea it could be wiring harness if you have. A bad connection somewhere. Or a bad plug. Was the cart towed anywhere in with the tow run switch in the run position. M

Christy, great video man! I have a 2015 Yamaha drive 48v with Same problems. Can you do have recommendation on finding the bad wire?

@HeyHeyHey97

2 жыл бұрын

On your small post on sol. The red wire. Run. A wire from main pos on battery to that post. And hit gas and see if runs

@joeabu

2 жыл бұрын

Selanoid is new still nothing. I jumped the selanoid on the small post from the main positive and it reverse started beeping. What does that mean? That there is a bad wire in the key switch? On the Yamaha, the wire that comes off of the battery charging Port you described, is not a wire that can be easily detached like on the txt. It just so happens that the on on my cart is soldered. Should I cut it and run it straight to the main + post and see if the cart runs? Thanks man you are a great help and appreciated for DIY.

@HeyHeyHey97

2 жыл бұрын

@@joeabu that means you have lost all power from key switch,tow switch or foot pedal switch... get a volt meter and check back of keyswitch for voltage.

@joeabu

2 жыл бұрын

@@HeyHeyHey97 just checked for v behind the key switch and I got at .24 reading point 24?

@joeabu

2 жыл бұрын

@@HeyHeyHey97 it does run when doing this. Main + to the small post on sol.

I have 48 volt to the to small wire with key off and as soon as I turn key on solenoid clicks but push gas no go its a 48 volt ezgo txt

@HeyHeyHey97

8 ай бұрын

Not good either a bad controller or something wrong with the pedal

Thanks sir Yellow wire was it

@HeyHeyHey97

3 жыл бұрын

Np subscribe to channel. I will be posting more videos....

I have a 2012 rxv that gets no voltage to the motor brake with key switch on but run / tow switch in tow does . I get reverse buzzer and hear solenoid click when turning on key switch but still no voltage from motor brake plug . Any suggestions ? Maybe you just showed it to me , the yellow wire from the solenoid ? Going to check that later . It's 3:37 am and I couldn't sleep thinking about my wife's cart not running the neighborhood .

@HeyHeyHey97

3 жыл бұрын

You should not get voltage to brake until you hit gas...

@HeyHeyHey97

3 жыл бұрын

It gets voltage from your plug under dash make sure you have good connection on your can plug. Which is the plug under the dash.

@HeyHeyHey97

3 жыл бұрын

Before you turn the keyswitch on pull back on the gas pedal and pull back on the brake pedal. And then turn the key back on and see what it does.

@guynoir4733

3 жыл бұрын

@@HeyHeyHey97 Thanks so much for letting me know that , I should've known that being that the cart holds on a hill when you stop . I was too tired to have at it after my regular job tonight and kinda glad now , I'll check tomorrow evening and if it has voltage when the throttle pedal is pushed I'll know that my motor brake is bad , am I right in that thinking ? Again thanks so much for the help .

@HeyHeyHey97

3 жыл бұрын

@@guynoir4733 thats correct.

I have a 2012 txt been sitting for a year with year 18 battery's I charged them up and I'm getting 33.1 volts and my ezgo charger the light want turn on green

@HeyHeyHey97

3 жыл бұрын

Is your cart 36 volts or 48 v

@HeyHeyHey97

3 жыл бұрын

If it is a 48 volt cart it will take 38 volts to kick charger on

I have a 1999 ezgo with DCS. It quit going forward. Will move in reverse. Any help appreciated.

@HeyHeyHey97

3 жыл бұрын

Can you get to your controller

@HeyHeyHey97

3 жыл бұрын

On top of your controller. Flip the black and white wire around and see if it goes forward then.

@HeyHeyHey97

3 жыл бұрын

Make sure your forward microswitch is good... it should be on the back of the f n r handle. Under the seat.

I need help. 36V 2007 EZGO. The batteries are fine. I rode it with a lot of resistance up the hill. The batteries got hot. I went for a hike, came back and the cart wouldn't move. I hear the click when I engage the pedal. Please help.

@HeyHeyHey97

5 ай бұрын

Just seen this. Do you still need help

@roymiller447

5 ай бұрын

@@HeyHeyHey97 yes. I need help. I replaced all the battery cables. The batteries are charged and showing 13 +. with the key switch and forward or reverse engaged. The solenoid will click. All four cables are secured to the electric motor . Any suggestions would be helpful. Thanks, Roy

@HeyHeyHey97

5 ай бұрын

@@roymiller447 do you have a f n r switch on the dash or a handle by your leg. For forward and reverse.

@HeyHeyHey97

5 ай бұрын

The reason I asked that is because I have videos on my channel to trouble shoot either type. And I was going to share the link with you

Good day mate, I got a 2000 motor ezy co 48vlt and trying to find the fuse on it, could you help thanks

@HeyHeyHey97

Жыл бұрын

What fuse. What kind of problem are you having

@ivanjuriss4772

Жыл бұрын

@@HeyHeyHey97 well it started with the buggy not moving at all but the reverse alarm was working still so we replaced the solenoid clean it so two weeks of not using it now there’s nothing working not even charging so look into it again to find out that the red wire runs from the charger plug on the buggy meet up with the black wire is rotted of so not sure whether that is the fuse or not but that’s as far as I go

@HeyHeyHey97

Жыл бұрын

@@ivanjuriss4772 your charger plug is a triangle correct

@HeyHeyHey97

Жыл бұрын

@@ivanjuriss4772 if your charger plug is triangle. That is a temperature sensor. The cart will not charge without it. You will need a new charger receptacle

@ivanjuriss4772

Жыл бұрын

Well the red wire I’m talking about is inside the buggy so there are three wire coming out of the buggy plug two black and one red so the red meet up with one of the black wire and it’s rotted off so not sure what’s that one for

I’ve been troubleshooting my gym cart for over 20 hours. 3:02 Thank you so much! Now, how do I fix it!

@HeyHeyHey97

Жыл бұрын

What’s it doing

@diehardfan173

Жыл бұрын

@@HeyHeyHey97 I ran a jumper like was shown in the video from positive to the solenoid, and the dash illuminated again and I could drive it. Since then, I’ve just been tracking the wires from the key switch to where they go. I am not reading 74 V at the key switch like this cart requires. So not sure what to do at the moment.

@HeyHeyHey97

Жыл бұрын

You have a gem cart correct

@diehardfan173

Жыл бұрын

@@HeyHeyHey97 I do early 2000s six battery 74 V two seater. E825 series

@HeyHeyHey97

Жыл бұрын

The voltage comes out the controller. Have you checked all the fuses and the main cut it breaker

I have a 2015 or so stinger48 electric cart. Bought 4 brand new 12volt batteries and the cart won't move. The solenoid clicks and it sounds like the motor engages, but when I try and press the pedal nothing happens. Any ideas?

@HeyHeyHey97

Жыл бұрын

What kind of cart do you have.

@bamadave1212

Жыл бұрын

@@HeyHeyHey97 it's a EZGO stinger 48

@HeyHeyHey97

Жыл бұрын

Does it have a brake on end of motor.

@bamadave1212

Жыл бұрын

@@HeyHeyHey97 I'm not totally sure.

@HeyHeyHey97

Жыл бұрын

Ok

I have a 2016 EXGO TXT 48v. I parked it just over a year ago. It sat in my garage for 2 winters without being charged. I thought I had unhooked the batteries, I did not. I got it out, plugged my charger in and it flashes 2 red lights indicating it has too much or not enough voltage. I then tried to charge each battery individually. They would charge and discharge within 45 seconds after being disconnected from the charger. I replace all 6 - 8 volt batteries and the cart wont move. I have voltage on both large posts of the solenoid with key on or key off, but when i turn key on the yellow trigger does go hot and back to 0 with key off. My batteries are reading 8.2 volts individually but when linked together they only read 32 volts. I charged each brand new battery and still the same reading. So, then I started at the ignition and then moved on to the solenoid. Thinking It may have been bad I replaced it. With the old solenoid it DID click. With the brand new solenoid there is no click. I am getting the same reading as I was with the old one installed. I moved on to the flat plug you showed at the end of this video and I have constant voltage on the red, Key on or key off. And It looks like I have no voltage on the white with key on or key off. What should I look at next? By the way, your video was great!! Thank you for sharing and trying to help us all save some money.

@Dune_Riders

Жыл бұрын

I do have Battery voltage at the throttle switch, under the floorboard as I push the throttle

@HeyHeyHey97

Жыл бұрын

Leave the red lead of your meter on main positive and keep moving your black lead of your meter from negative on each battery in series. And see where you voltage goes away at. Could have bad wire or bad battery

@Dune_Riders

Жыл бұрын

@@HeyHeyHey97 thank you! I will try that. That would mean I’ve lost 2 batteries voltage. The cables look good but I will test and update

@Dune_Riders

Жыл бұрын

Well, I feel like an absolute idiot. But with our taking a second and messaging you I may not have figured out the problem. I did exactly as you said and found I had no voltage from the last battery. I realized I hooked it up backwards. Flipped it around and hooked it up properly and BAM! It moves. Now the charger worked and I’m back in business. Thank you for your help. Sometimes we like to make things harder than they are. Sometimes we overthink things as I did in this situation. Thank you again

@HeyHeyHey97

Жыл бұрын

It’s all good man. I been doing it for 28 years. And that’s how it is sometimes💪💪

Thanks for the video very informative I’m having trouble with my EZ- GO doesn’t want to move when I press the pedal. I have switch the solenoid and ITS and still no luck and I just discovered today that the wire from the key switch, pedal and micro sensor the white,black,green and red wires do not have voltage nor does any voltage appear when I press on the pedal and the solenoid does not seem to be clicking on any idea what can be going on ?

@HeyHeyHey97

8 ай бұрын

Does your reverse buzzer work?

@SandraPerez-vu1wc

8 ай бұрын

Yes reverse buzzing sound works but the wire harness doesn’t seem to get voltage batteries are charged and giving correct voltage

@SandraPerez-vu1wc

8 ай бұрын

Seems like enable pin is not receiving power

@HeyHeyHey97

8 ай бұрын

Is it a 36 volt or 48 volt

@SandraPerez-vu1wc

8 ай бұрын

36v

My 2005 Ezgo has brand new batteries and the charger is good. It runs good but up a semi steep hill it looses power. Am I just trying to make it do something it's not capable of doing or is something wrong.

@HeyHeyHey97

3 жыл бұрын

All ezgo will loose power going up a hill. Execpt for an ezgo RXV. All you can do is get you something like motor and controller to give you more speed so you can hit the hill faster.

@marietaddeo6155

2 жыл бұрын

@@HeyHeyHey97 I have a 2005 Western Electric LSV. I am having trouble. My Cart will go in Reverse but not Forward. I have 7 2 yr old Trojan Batteries and I had all new Wires put on 2 mths ago when I experienced the same Issue and at that time the FNR switch tested good. Any ideas what I can check next?

@HeyHeyHey97

2 жыл бұрын

Do you have a handle by your leg. Or an actual f n r switch for forward and reverse

@marietaddeo6155

2 жыл бұрын

@@HeyHeyHey97 I have the Switch on the Dashboard

@HeyHeyHey97

2 жыл бұрын

I would flip the top and bottom wire on the switch and see what it does. Since it has happened before going to say bad switch or bad wire going from switch to controller.

I have a 2011 ezgo txt pds with brand new batteries and only goes 3-4mph. If it’s already running do you think it’s the ITS or possibly the speed sensor. Let me know what you think please

@HeyHeyHey97

2 жыл бұрын

If speed sensor. Whenever you flip the tow switch to tow then back to run. It will take off wide open then cut back down. Try that and let me know. It’s NO

@HeyHeyHey97

2 жыл бұрын

ITS NO

@floridavriot

2 жыл бұрын

@@HeyHeyHey97 it does not do that. It is consistently very slow

@floridavriot

2 жыл бұрын

@@HeyHeyHey97 what do you mean it’s NO?

@HeyHeyHey97

2 жыл бұрын

No it would not be the ITS

Nice vídeo i want to know where the wire from to solenoid

@HeyHeyHey97

Жыл бұрын

What color wire yellow?

@HeyHeyHey97

Жыл бұрын

If you are talking about yellow wire it comes from key switch. But it connects to a couple of other wires under the floor board.

I'm working on a 48v ezgo txt and the batteries are at 47v, no click from solenoid, scanner said throttle issue and HPD, so I replaced harness from 4 pin plug to throttle box, replaced sensor and micro switch, still same issue, scanner reads throttle position at 60% even when pressing in and out, not getting voltage fluctuation when measuring black wire on 4 pin to batt neg. Any tips would be much appreciated.

@HeyHeyHey97

Жыл бұрын

Unplug the wire from the it’s. Or throttle sensor and see what it shows

@HeyHeyHey97

Жыл бұрын

Also make sure there is no sign of water in the pedal if there is water under the its. It will give false reading

@dannymcreynolds1060

Жыл бұрын

@@HeyHeyHey97 no sign of water intrusion, with black wire unplugged from ITS the voltage drops from 2.7v to 0

@HeyHeyHey97

Жыл бұрын

With everything you replaced. Controller. Did it show the same thing with the other the its in the pedal box

@HeyHeyHey97

Жыл бұрын

What does the white wire show go to the its

I have an EZGO I have 50 volts on all four post on the solenoid with the key in ON Position is that normal? Should I be getting 50 volts on only three post and one ground? Please advise thank you

@HeyHeyHey97

2 жыл бұрын

Do you have a run tow switch and what color are on the small post on sol

@luisestrada9071

2 жыл бұрын

@@HeyHeyHey97 yes I do have a tow switch and as for the wires I have a red and a black wires on each post

@HeyHeyHey97

2 жыл бұрын

@@luisestrada9071 the ground post will show a hot until you hit the gas. What color are the wires on the small post

@luisestrada9071

2 жыл бұрын

@@HeyHeyHey97 red and black

@HeyHeyHey97

2 жыл бұрын

@@luisestrada9071 does the sol click

I have a 48v golf cart (motor sticker says 48v and I have 8x 6v batteries) it is a western elegante (mostly ezgo) but the sticker on the solenoid says 36 volts so my question is this, should the yellow wire from the key to the small terminal on the side of the solenoid be supplying 36 or 48 volts if the sticker on it says it's a 36v solenoid? Does that also mean that it is only design to have 36v passing through the large terminals?

@HeyHeyHey97

3 жыл бұрын

It is supposed to show battery voltage

@portlandlocalchurch8168

3 жыл бұрын

@@HeyHeyHey97 I edited the wording on my question to make more sense, speech to text is a killer ha ha

@HeyHeyHey97

3 жыл бұрын

Well the ezgo rxv are 48 volts but they activate off 36 but allow 48 volts across big post. Send me picture of your sol.

So if i have a 38vt cart ,all the wires from the pedal switch show 38vts and don't change with pedal depressed what does that mean

@HeyHeyHey97

2 жыл бұрын

You have a 48 v or 38 volt

@ashtonnuckols2663

2 жыл бұрын

@@HeyHeyHey97 38volt

@HeyHeyHey97

2 жыл бұрын

They dont make a 38v

@HeyHeyHey97

2 жыл бұрын

I meant 36

@HeyHeyHey97

2 жыл бұрын

So you have a 36v ezgo

Hello, I have 2013 rxv ezgo. We were going up hill and it quit. Sometimes it's wants to go for a few seconds. I followed all your troubleshooting in video. I'm wondering if it's pedal switch. I have 48v on red wire and 0 on green. On accelerator sensor I have 5v on orange 0v on black and 0v on yellow. When I push pedal down I have 5v on orange 5v on yellow and 0v on black. What's your thoughts?

@HeyHeyHey97

Жыл бұрын

If you turn the key on and put in tow will the brake release

@brentduncan2137

Жыл бұрын

@@HeyHeyHey97 no, we had to change unplug wiring plugs 1,2,3 4 and follow directions to switch to auxiliary power to tow cart

@HeyHeyHey97

Жыл бұрын

@@brentduncan2137 sounds like bad sol

@HeyHeyHey97

Жыл бұрын

When you hit the gas. What does it do when not running

@brentduncan2137

Жыл бұрын

@@HeyHeyHey97 I turn key on and I hear solenoid click. I push pedal I hear a slight noise by control area, like a puff of air. Really weird

You sure help me get dizzy

@HeyHeyHey97

3 жыл бұрын

Lolol. It's hard doing it by yourself. Thanks for the input though...

I have a 2011 ezgo gold cart and it won’t move, I bought a new solenoid,new it’s cable, new forward and reverse switch, new throttle sensor, batteries all new, tested motor and it’s good, could it be the dc controller?

@churrosent

2 жыл бұрын

@@HeyHeyHey97 Yes, reverse buzzer works also

@churrosent

2 жыл бұрын

@@HeyHeyHey97 It’ll probably take like a second to click on and off

@churrosent

2 жыл бұрын

@@HeyHeyHey97 Thanks.

@HeyHeyHey97

2 жыл бұрын

Did you get cart running

@churrosent

2 жыл бұрын

@@HeyHeyHey97 Not yet I’m trying to find a Curtis controller, I have a dc Curtis controller model 1206HB-5201 on my golf cart, all I can find is model 1266A-5201, I’m wondering if that’ll work

Got a ezgo txt 07 model solenoid clicks but no movement forward or reverse

@HeyHeyHey97

6 ай бұрын

You have a 36 volt Ezgo pds??

@HeyHeyHey97

6 ай бұрын

You have a f n r switch on dash. Or a handle by your leg

@user-it1sf3cu6l

6 ай бұрын

It has the f&r switch is on the dash. Charged all the batteries changed a couple of battery cables and cleaned the rest of them. I got it going . Took it back to my aunts she drove it about 2 days and it got real slow wouldn't hardly go. Any help is appreciated

@HeyHeyHey97

6 ай бұрын

When you hit the gas and the solenoid click. While you hold the gas down. Does it click back out by itself. Or it doesn’t click back out until you let go of the gas

I’ve got a 2014 EZ-GO TXT 48 volt. I just replaced the micro switch and the inductive throttle sensor. They seem to be working but the cart won’t do anything. The batteries are fully charged, the lights, turn signals and horn work. I have the toggle switch in the run position. The reverse alarm does not come on and I don’t hear the solenoid click. What should I troubleshoot next?

@HeyHeyHey97

Жыл бұрын

Bypass the charger plug. Like I did in the video. It’s within the first couple of min. And see what it does

@sethkorros2467

Жыл бұрын

@@HeyHeyHey97 Thanks, I’ll try that. Can I jumper a wire without cutting off the plug?

@HeyHeyHey97

Жыл бұрын

@@sethkorros2467 yes. But I would just do it and make it permanent. Eventually it will give you a problem. If it’s not one now

@HeyHeyHey97

Жыл бұрын

@@sethkorros2467 if that doesn’t fix it run a wire from main positive to small yellow wires on sol and see what it does

@sethkorros2467

Жыл бұрын

@@HeyHeyHey97 I bypassed the charger plug and nothing happened. I also ran a jumper from the the main positive to the yellow wire on the solenoid and that didn’t work either. Is there anything else I can try?

Good info, but im getting dizzy.

@HeyHeyHey97

9 ай бұрын

Yes this is one of my first videos. Thanks for watching and commenting

I did all the test in the video everything checks out and I just replaced the solenoid I have all the correct voltage back up alarm is loud but cart won't move in either direction any ideas on what I can check next

@HeyHeyHey97

2 жыл бұрын

Check the it's in floor board.

@HeyHeyHey97

2 жыл бұрын

Its. With volt meter should show 14vdc on one wire and 3vdc at full pedal other wire black lead on main negative of batteries

@mw20001

2 жыл бұрын

I removed the rubber mat they was a little cover with 2 Phillips screws took cover off at the back of cover they are 2 wires one has 14.7 volts and other has 1 volt then I press the pedal it goes to 2.7 volts

@HeyHeyHey97

2 жыл бұрын

Put black lead of meter on m- or a1 on controller and red lead on main positive on battery. Hit gas and tell me what you get. 0

@HeyHeyHey97

2 жыл бұрын

Excuse the 0 at the end. You should get battery voltage. Does the sol. Click when you hit gas.

My white wire reads 0 Everything else reads good. Any ideas.

@HeyHeyHey97

Жыл бұрын

Have a bad it’s in floorboard. The sol does not click. Correct

@parales03

Жыл бұрын

@@HeyHeyHey97 the solenoid does not click. What can it be? I’m so confused at this point.

@HeyHeyHey97

Жыл бұрын

@@parales03 if the white wire shows no voltage then you have a bad its. It’s in the floorboard. If that’s bad sol want click

@HeyHeyHey97

Жыл бұрын

As long as the black wire shows voltage going to the its.

Hi I have a txt 48v done all the test you recommended and all reading correct cart has new solenoid, new controller and ITS and still won’t run got reverse buzzer but solenoid still won’t click ?

@HeyHeyHey97

2 жыл бұрын

Do you have voltage on small post on sol when hit gas

@joshlewis4718

2 жыл бұрын

@@HeyHeyHey97 on the blue or yellow ?

@HeyHeyHey97

2 жыл бұрын

Put black lead of meter on main negative and check yellow wire with red lead. With key on.

@HeyHeyHey97

2 жыл бұрын

If voltage there put red lead on yellow wire and black lead on blue wire hit gas see what it shows.

@HeyHeyHey97

2 жыл бұрын

What does overall battery voltage show

I couldn’t understand the 3rd common problem (my 1 yo broke the speaker on my phone) you said it’s a bad what? - reed switch - key switch - ??? Thanks!

@HeyHeyHey97

3 жыл бұрын

Its it is called a its. Inductive throttle sensor which is in the floorboard in front of gas pedal.

Do you have an email address or a social media I can reach you? Just had my controller fry not sure why but don’t want to purchase another controller and have the same thing happen. Thanks in advance!

@HeyHeyHey97

3 жыл бұрын

Look up thomas wells on face book Conway sc

@HeyHeyHey97

3 жыл бұрын

What kind of car you have. If an ego make sure you have a resistor controller. And check its in floorboard.

@HeyHeyHey97

3 жыл бұрын

Call tom 843-427-4853- and ask for Thomas. 8-5 Monday thru sat..

@hemiboy29

3 жыл бұрын

Thank you!

You sure get people dizzy

@HeyHeyHey97

2 жыл бұрын

Thanks for watching. Its hard to do everything by yourself

Would love to see this video where the image wasn’t constantly being flipped upside down and you actually get perspective about what you’re looking at without getting nauseous. Obviously a great bit of knowledge but I gave up.

@HeyHeyHey97

3 жыл бұрын

Lol. Yep it's hard holding the phone and everything by yourself. But thanks for the input....

Get a new camera man

@HeyHeyHey97

9 ай бұрын

I am accepting applications for one. If you need a job

@kevins5268

9 ай бұрын

@@HeyHeyHey97 150$ an hr

@johns9779

10 күн бұрын

Here's a thought. Stop complaining about free education and figure it out yourself.

@kevins5268

10 күн бұрын

​@@johns9779lol I usually do, fly safe little Johny.

@HeyHeyHey97

10 күн бұрын

@johns9779. Comment of the year my man 👊👊👊👊