Finally a video of someone using some sort of resistor on the Tx pin!

very good explained,not only this one ,every videos of you i watched are very informative and educational,keep it up and thank you very much.

@robojax

3 жыл бұрын

you are welcome. I am glad you found it useful and subscribe and share. that will help me a lot. thanks.

very very coool! thanks! the only code thats works .... great job!

@robojax

4 жыл бұрын

Glad it helped. The best thank you for me is to not skipping ads and Subscribing 🔔 to my channel, and clinking 👍 the video. It is greatly appreciated. 🔔 😊.

Really Great video to start with... Excellent Work sir...

@robojax

4 жыл бұрын

thank you.

Great 👍

This was a very informative video 😃

@robojax

4 жыл бұрын

Thanks.

Hello sir, Excellent tutorial. thanks.

@robojax

4 жыл бұрын

You are welcome.

@ouchanihida3327

3 жыл бұрын

@@robojax I have a small problem. I need to use components that are compatible with Arduino. A position sensor (so I use a GPS module. This GPS module must be Adafruit Ultimate GPS Data Acquisition Module (GPS Included)). A position storage (with an SD card that must work with an SPI link). A bluetooth interface. A GUI to visualize the route (using an Android tablet that is compatible with a bluetooth module). you can advise me to use what as a component . because it's 3 components must be compatible with Arduino and an Android tablet IHM thanks to a Bluetooth module.

Can u tell me plz if I want to joint a vibration sensor, when that sensor will detect vibration then the location will go to the particular number can u tell me how to do this plzzzzzz...

@randolphmiller2655

4 жыл бұрын

You want me to build your project for you to sell, give me enough money to make it worth my while and Ill be happy to do that. I also want profit participation.

Hi Robojax, how are you? Well, I try this code and I receive the data of GPS TX in Arduino UNO TX but when a upload the code the ARduino dont read nothing in serial. I use the reset and I confirm the receipt of the GPS data including tested and confirmed in the freenmea. What could be happening?

@robojax

6 жыл бұрын

Hi, please share your code codeshare.io/ and once you post it, you will get a new URL (address), then post the URL here by clicking on "reply" and I will try to see if I can find the error . snag.gy/AHhRpV.jpg

@AnkitAnkit-bu8xb

5 жыл бұрын

You can't receive data from Arduino Tx

thank you sir! i really find this video helpfull and easy to understand! i would donate some if i had any way. keep it up and i am eager to see updates on this module. can i set a course by it and command a robot to go to desired position?

@robojax

5 жыл бұрын

Thank you for support. This project was to get the location. Using arduino you won't be able to direct a robot. Raspberry Pi is best choice for simple robot. But with arduino, you can guide in a simple rout like football field. Here my paypal donation link: bit.ly/rj-paypal if you wish to donate

Now it more clear. New world

..is there any chance that the RX pin is not working but we can get right NMEA data because in my case I m getting right NMEA DATA but when I m working with "while(gpsSerial.available()) "..command it's not working...can you please tell me what probably the error ..... Thanku

@robojax

6 жыл бұрын

The device gets data from RX and puts label. NMEA data you are getting is without location and time and other satellite data. so it is possible that your receiver is bad. Many thing could go wrong. Only you can find the fault if you compare it with another working module.

Can you power the Arduino with a 9V battery and still get your computer to receive the GPS information?

@robojax

5 жыл бұрын

Yes you can. That connector is made for that purpose.

@Ali-hs9sr

5 жыл бұрын

@Seth Vahra - Chinguacousy SS (2422) you need to use HC-12 Module

Are the connection will be the same if I use neo 6m v2, which have five points, with extra PPS?

@robojax

4 жыл бұрын

I will reply to all Subscriber's 🔔 questions. So make sure to Subscribe.😊. You haven't Subscribed yet. I spent hours recording and preparing it so you learn, what is single click to subscribe in return?

U r demonstrating Ublox NEO 6M, can I use same configurations for Ublox NEO 7M???

@robojax

4 жыл бұрын

Yes you can. Or want my other video kzread.info/dash/bejne/mpaG0tRqeMWqlps.html

what about we want to get signal from 2 gps? i mean, i have 2 gps and i want to get signals from them with 1 antenna which connecting to my pc. Is it possible that get signals from 2 gps with 1 antenna at the same time?

@robojax

5 жыл бұрын

I don't think you can use the same antenna for two GPS receiver. The antenna is active device, it has electronics and it communicates with receiver.

Very useful video.Is it possible to keep in mind of arduino the coordinates tha 6m gives and after this the arduino by giving settings to 3 servos to try to go again in the spot lock?

@robojax

5 жыл бұрын

you can program arduino for sure. I was planning to make videos on that but got very busy.

@antonis2814

5 жыл бұрын

Do you know where can I find the code if this?I m trying to find it and I can’t.There is no somewhere at internet.

@robojax

5 жыл бұрын

I am not sure.

Can the Beiou or Indian GNSS version with about 1 meter accuracy, work in the USA ?

@robojax

5 жыл бұрын

I am not sure I about different satellites but for accuracy you can use Neo-7m and 8m.

@randolphmiller2655

4 жыл бұрын

NO

How you give power to Arduino? Using adaptor or using 9v battery?

@robojax

5 жыл бұрын

from USB. But doesn't matter.

i have made the connections from arduino uno to gps Neo-6m but i open arduino ide i cant see anything in serial monitor......can you please help me with this

@robojax

5 жыл бұрын

Other than tell you to check the wiring and make sure you have not changed the code. I can't help. Please check my latest video on GPS kzread.info/dash/bejne/mpaG0tRqeMWqlps.html you might find is better. I am not sure.

I Want to control load and monitoring Voltage and Current by Blynk using arduino uno and sim 900 please recommend me

@robojax

4 жыл бұрын

why you use that service and how much do you pay? I don't like services if they don't offer some type of free to people. I will not support it if they don't have free service for students . All my videos and 1000s of hours of work are offered for free.

Can I use neo 8mn gps module for this project? with the same arduino

@robojax

3 жыл бұрын

I have not tested it but I believe yes.

thank you

@robojax

5 жыл бұрын

You are welcome.

respected person, when i connect simple "TX" of Arduino to "TX" of GPS it shows the data on serial monitor. But when i upload the code and then connect "RX" of Arduino to "TX" of GPS then it shows noting on serial monitor. Please Help.

@robojax

5 жыл бұрын

Assalamu alaikum Haris , I don't know would be wrong, I have another video (latest) on GPS: kzread.info/dash/bejne/mpaG0tRqeMWqlps.html

Hello, will this give live updates? And can I connect it to my app?

@robojax

5 жыл бұрын

You should be able to do it. here is my latest video kzread.info/dash/bejne/mpaG0tRqeMWqlps.html

Hi i have this all material, i wonder how do i connect my gps to the app that i will make, because i want to make an gps app that will show my exact location etc.

@robojax

4 жыл бұрын

Hi, for that you need to use Bluetooth with Arduino to send it to your mobile device. Then in your app, it should be able to read the data and display it on map.

Can you write a code to transmit the data of this GPS module wireless like with rf transmitter?

@robojax

5 жыл бұрын

You will need to data stransmitter or XBee or some other means.

Amazing! I now know where you live

@robojax

4 жыл бұрын

LOL. Yes.

Votre vidéo est très instructive et enrichissante! Question: Peut-on extraire d'autres informations du NEO-6M par exemple l'heure locale, la vitesse,....? Merci beaucoup

@robojax

Жыл бұрын

Bien sûr que c'est possible. Je me suis concentré sur les coordonnées parce que la plupart des gens en ont besoin. Regardez attentivement ce que j'ai fait et appliquez le même principe pour extraire d'autres données.

@robojax

Жыл бұрын

Vous pouvez regarder cette vidéo où j'ai utilisé une bibliothèque pour extraire la coordonnée kzread.info/dash/bejne/mpaG0tRqeMWqlps.html

Hi, Can anyone help me, please! I am facing an issue with the final code(lat and long). I follow the whole video the GPS is working and give the exact location after uploading the simple blinking code to the Arduino but when I upload the final code (which link is present in the description of this video) it not show any output in the serial monitor..!!

@robojax

5 жыл бұрын

check the baud rate settings snag.gy/y3pKwG.jpg

@Abdullahtheengineer

5 жыл бұрын

@@robojax Yes I keep the baud rate 9600 but it not working!

@Abdullahtheengineer

5 жыл бұрын

Can you tell one more thing, Where to connect the RX and TX of the GPS to the ARDUINO?

your video is so amazing I want to know Can We count Trip distance from this Gps module? If yes then plz guide me I really need it

@robojax

6 жыл бұрын

Thank you. You can calculate the the distance between points. Here is starting point for you stackoverflow.com/questions/365826/calculate-distance-between-2-gps-coordinates

hi sir, i had collected all the pins as you describe in the video, but my serial monitor does not show anything. i have tried this many time but same;screen is blank. is there any problem in my neo 6m? and how much time gps module take to synchronize withe satellite

@robojax

5 жыл бұрын

Hi, about 1 minuet to get satellite signal if you are in open space. If you are by the window, and signal is weak, it might take 3 minuets to get signal.

@shruti2096

5 жыл бұрын

@@robojax I tried this, but still nothing is displayed on the screen

@robojax

5 жыл бұрын

If the code and wiring is correct and you are in open field, then your GPS module is bad. Try with another GPS module.

Shukraan!

@robojax

5 жыл бұрын

afwan.

Hello brother i have a small doubt... If we don't solder the pins in the gps module would it work anyways? I mean like if i just plug the pins without soldering will it work?

@robojax

3 жыл бұрын

Hello, yes it will work.

@kewinprasad_8434

3 жыл бұрын

@@robojax ohh thank you so much for the reply bro... I dont know why my GPS isn't working... I think it is broken

My GPS data is not stabilizing at all. The light in the gps module doesn't glow and I keep getting some garbage values in the serial monitor. What might be the reason?

@robojax

5 жыл бұрын

Hi, because you might have set the Baud rate of serial monitor incorrectly. see this snipboard.io/y3pKwG.jpg

Спасибо

@robojax

3 жыл бұрын

Добро пожаловать. Я забыл сказать вам, что я могу читать и писать по-русски, но забыл большинство слов и не могу говорить.

after i connect the pins with rx and tx and the module blue led does not blink, but the numbers and letters still coming out from the COM4 serial monitor, am i missing anything?

@robojax

4 жыл бұрын

you are getting useless data without coordinate. You should be in a spot where satellite signal reaches you either close to a window facing South or in an open space where south portion of sky is visible.

@nikariff18

4 жыл бұрын

@@robojax okay i went outside and tried it for a few minutes, the only thing that came out is the red LED blinking, the blue LED doesnot. The GPRMC code does not appear, could be my gps sensor is faulty?

@nikariff18

4 жыл бұрын

@@robojax oh i just notice my serial monitor displays gnrmc instead of gprmc, maybe my country has to do with the code appeared

@robojax

4 жыл бұрын

good to hear that. good luck.

Hi Sir, once i connect the 5v wire into my gps module but why my serial monitor does not show anything? I have try many time it still the same. Its that possible my gps module is broken ?

@robojax

5 жыл бұрын

did you check the baud rate? 9600 or whatever value you set? try this inside loop, just after loop() { Serial.println("Testing"); and see if it prints the text.

@roylim4738

5 жыл бұрын

@@robojax Thx for replying, yes i try all the baud rate, i set the bound rate to 9600 but still cannot get anything at the serial monitor, i have try the Serial.println("Testing"); it does not prints the text out. It means my component broken already?

@robojax

5 жыл бұрын

do you use another Arduino or do you use serial monitor for another thing? if not then inside the setup() do you have Serial.begin(); please copy and past as if you type, upper or lower case letters, that will create problem.

@roylim4738

5 жыл бұрын

Robojax yes I use the serial monitor for other components it works well. I am using the normal led blink code at the example there.

@robojax

5 жыл бұрын

are you using it at the same time? if not you should not have issue. if you use it at the same time, just make sure the baud rate is the same and it should work.

Can we use ESP32 rather than Arduino board?

@robojax

4 жыл бұрын

Yes you can.

please make a video on iot based gps tracker with source code and schematic diagram with neo-6 module and sim 900a

@robojax

5 жыл бұрын

that would be a nice project. I will work with GSM but not beside my full time job at a university, I am also student. So I don't know when I will be able to do it.

@randolphmiller2655

4 жыл бұрын

You want me to build your project for you to sell, give me enough money to make it worth my while and Ill be happy to do that. I also want profit participation.

Blue led is not blinking in my module and not giving the gps data even after few minutes. What should I do?

@robojax

4 жыл бұрын

something is wrong. Either wiring is bad or GPS signal is not reaching the module.

Is it possible to operate motor by using GPS module..?

@robojax

6 жыл бұрын

sorry I did not understand. GPS module is to receive GPS signal . To run a motor, you need motor driver module. These are two totally different things.

@nirmalkishore2879

5 жыл бұрын

Do u know what GPS will do haa

@narendrasajja2106

5 жыл бұрын

not exactly, i think it may transfer signals

excuse me sir, that's awesome project, but when i copy my Latitude and Longitude from my serial monitor to gmap coordinate it doesnt work, invalid coordinate, can u help me please?

@robojax

5 жыл бұрын

Of course it will not work. Your gmap needs it in certain format. Check this page and see how it is displayed and change Arduino code for the format you need. www.gps-coordinates.net/

@mubashirayub6630

4 жыл бұрын

@@robojax Can you plz convert your own Serial monitor value to Latitude and Longitude...

I always receive '****' every time i upload the code. Can anyone tell me the reason

@robojax

4 жыл бұрын

first make sure you set the baud rate of serial monitor correctly. See this snipboard.io/y3pKwG.jpg nad then please used unchanged code first and then change the code.

how to add sim slot and micro SD ? and how to trace it by sim card ? is it even possible ?

@robojax

4 жыл бұрын

In Arduino we have a SD car module where you can save data. Get that module and make sure you can write to SD card. then the values that you print on the Serial monitor, save it on the SD card.

This video was really informative sir. But I have a small confusion here. The GPS co-ordinates we get are something like 17.25963, 78.58463. Like somewhere between -90 to +90 Latitude and -180 to +180 Longitude. The values you are getting are in thousands... How can you justify this sir???

@robojax

3 жыл бұрын

just first two digits are the degree.

@pardhunadella2524

3 жыл бұрын

@@robojax You mean we have to do a float division by 100 to get the value in degrees sir?

I have a small problem. I need to use components that are compatible with Arduino. A position sensor (so I use a GPS module. This GPS module must be Adafruit Ultimate GPS Data Acquisition Module (GPS Included)). A position storage (with an SD card that must work with an SPI link). A bluetooth interface. A IHM to visualize the route (using an Android tablet that is compatible with a bluetooth module). you can advise me to use what as a component . because it's 3 components must be compatible with Arduino and an Android tablet IHM thanks to a Bluetooth module.

@robojax

3 жыл бұрын

Hello, Arduino forum with 1000s of community member is there to help forum.arduino.cc/ they help for free if you post your question. or paly someone here www.upwork.com/

@ouchanihida3327

3 жыл бұрын

@@robojax I have to use an ultimate adafruit GPS module. Which will be compatible with an SD card and a bluetooth module (all its components must be compatible with an Arduino) you can advise me to take what as type of components

What should i do if i want to use it to track vehicles? Can you teach me pls huhu

@robojax

4 жыл бұрын

to track a vehicle you will need a GSM transmitter (with SIM card) that can send SMS as location to you or send location to web server. this is a good project to do. But I got no time. Busy with full time job and part time Graduate studies.

@ejunlucagbo6868

4 жыл бұрын

@@robojax I never expected that you'll reply wow. But thanks, I hope you will make a video soon. Thank youuu

how can we increase baud rate and update rate of NEO 6M gps module using arduino........

@robojax

5 жыл бұрын

Watch my other video on GPS which used library. You should be able to change the communication speed from there kzread.info/dash/bejne/mpaG0tRqeMWqlps.html

@learn7710

5 жыл бұрын

thank you .......

@robojax

5 жыл бұрын

You are welcome.

hey friend, i cant upload the code to my arduino, it turns out that there are a problen when i upload the code, what can i do?

@robojax

6 жыл бұрын

send the screen shot from the bottom of Arduino screen where it shows what is wrong. Post it here snag.gy/

@fcoch7

6 жыл бұрын

Ooh, thanks for your answer, i solved the problem, it was that i didn't had the tinygps++ added, but anyway the gps doesn't get any signal

@robojax

6 жыл бұрын

change your location, get the module closer to window or go outside to test it.

@fcoch7

6 жыл бұрын

Robojax i know, i have tried that too :( but it doesn't work either.

@fcoch7

6 жыл бұрын

Robojax could you speak me to my email, i really need to do this for my final university proyect, I would be very grateful if you could help me buddy. My email is fcoch7@gmail.com

Hi awesome tutorial but my serial monitor is not printing lat and long separately as urs is doing. My output is ⸮.79298,N,07707.39270,E,1,07,1.41,201.4,M,-40.0,M,,*71 $GPGSA,A,3,⸮ and i have used ur same code . could u pls help?

@robojax

4 жыл бұрын

You haven't subscribed to my channel. I will reply to all Subscriber's 🔔 questions. So make sure to Subscribe.😊

Hello, i connected my gps module with my esp8266 for the first time it worked but after that I'm not getting the latitude and longitude it's showing 0.000000 for both, even though led is blinking, I'm getting this problem, what's the solution for this??

@robojax

2 жыл бұрын

Hello, it might be that your location is not receiving signal. change your location if you did not change the code.

@darshanbabu1142

2 жыл бұрын

@@robojax i tried at different locations for many minutes but also It's showing same, initially i got the signal even though I keep my device in the same place I'm not receiving the signal but the module is blinking

@robojax

2 жыл бұрын

if you are on open area and module has power, then something is wrong with the module.

Does anyone know if adding the resisters is needed? And why?

@martanijet4583

5 жыл бұрын

Same question

Won't be able to access this website freenema.net/decode Is there is any other way to decode NEMA Codes

@robojax

4 жыл бұрын

I don't remember what I said in the video but you don't need to access any other website. Just run the code and extract the location.

Hello Robojax, I tried your code, but I am using the Arduino Mega 2560 and nothing is displayed. Could you indicate what to change in the code. Ultimately, I need to extract the speed from the VTG message. Could you enter the code on codeshare.io ?? I promise donation. I am fresh on these matters, but I need this for my master's thesis and I care about the time (I have only a month). Pleeeeese

@robojax

5 жыл бұрын

It should work Test it on Arduino uno and then move to Mega. I have another video where you need library. Try that as well. kzread.info/dash/bejne/mpaG0tRqeMWqlps.html

why i am getting 0.00 all the time...can u please help me

@robojax

5 жыл бұрын

Because : 1-Wiring is incorrect 2-either you are indoor and your module can't see the sky above (not horizon) 3-Your module is dead.

@saikumar.s3518

5 жыл бұрын

@@robojax working fine..thanks for this tutorial..

so how is thissent to a server over an api

@robojax

3 жыл бұрын

use WiFi or Ethernet module to send that over network to database or other purpose.

@bonaventureokoli7988

3 жыл бұрын

@@robojax thank you

The extracted location is Pickering Christian School :)

@robojax

3 жыл бұрын

LOL.

I my case led is bilking but location is not sho

@robojax

4 жыл бұрын

Check the serial monitor snipboard.io/y3pKwG.jpg

hi sir, my led of gps won't even blink and when i open serial monitor, nothing comes out =(

@robojax

6 жыл бұрын

how did you connect it? Did you connect it to 3.3V? you can't see anyting at serial monitor until it the LED shows blink and then solid. So if you have connected the wires incorrectly, it might be dead. Try it on another GPS module.

@TEKKENEnterMyDragon

6 жыл бұрын

incorrectly as in tx to tx, rx to rx would cause the board to burn because vcc and ground are always correct? no i connected to 5v, the led blinked once in red color and i never see it blinks again

@robojax

6 жыл бұрын

Are you close to window (facing south) where the device sees the sky? It need to receive the signal .

My gos module is not sending any data. Any suggestions?

@robojax

4 жыл бұрын

GPS module doesn't sent data. It receives them and your arduino should display it. Check the wiring.

@monisankarnath

4 жыл бұрын

I connected the tx and rx of gps to the tx and rx of Arduino(reversed). Used 3.3v of Arduino but the led of gps is not on and nothing is displaying in the monitor.

@robojax

4 жыл бұрын

I don't remember, but doesn't it need 5V?

@monisankarnath

4 жыл бұрын

No that will most probably destroy it. I read somewhere that the GPS module requires some time to start. How much time did it take for you?

@robojax

4 жыл бұрын

it depends how clear the path to sky is. Perhaps 30 seconds to 90 seconds.

When i connect it no data shows up on the serial monitor

@robojax

3 жыл бұрын

please see this image that shows you how to set the serial monitor snipboard.io/y3pKwG.jpg please reply it resolved the issue. good luck.

@mohamedjundi1572

3 жыл бұрын

@@robojax i have it already at 9600

@mohamedjundi1572

3 жыл бұрын

@@robojax so far I have uploaded the blink code and the arduino blinks normally, but when I connect connect all the wiring for the gps module nothing shows up on the serial monitor, and the gps does not light up either.

Please activate the subtitles for the Romanian language as well .

@robojax

Жыл бұрын

Hi just added Romanian subtitle.

@John_Smile

Жыл бұрын

@@robojax Thank you very much !

@robojax

Жыл бұрын

you are very welcome.

@John_Smile

Жыл бұрын

@@robojax I really appreciate the clips you've made. On the one hand I like to add subtitles, otherwise I would have understood 50-60% of the words spoken. (I don't know English very well.) On the other hand, I like that you are a smart boy and you are quite good at electronics and you are willing to share your knowledge with us, to those who "do not distinguish a resistor from a capacitor". (I'm kidding, obviously, but I want you to understand that, compared to you, my knowledge is 0... zero.) Bye !

@robojax

Жыл бұрын

No worries. Every person has strength in something. I am glad you like found it useful. I try to have Romanian subtitles on all my videos, but somehow I forgot. Here is another video on GPS which uses a library kzread.info/dash/bejne/mpaG0tRqeMWqlps.html

total cost

@robojax

4 жыл бұрын

Arduino $4 to $15 . GPS module $8 to $25 depending how fast you want them and where you buy them from. eBay, Amazon and aliExpress are the sources.

Title should be GPS, GSP stands for George St. Pierre.

@robojax

6 жыл бұрын

Wow. Thank you. Even now I read it GPS until I read the "George St. Pierre". LOL.