Thanks Tim. Very helpful.

Thanks Tim!!! I seriously appreciate this video!!! I found the link in the hull truth forum. Chalk me up as another 3 finger salute guy. I'm taking the emm off today to send to Chet per all of your advice in the forum. Being able to find this kind of information and videos is absolutely priceless! I just bought my first boat and I'd be completely lost right now without you guys.

@timvogel2407

Жыл бұрын

Glad it was helpful!

HI my name is Daniel Ranieri, I´m from Buenos Aires Argentina. Please can you say me where is the place that repair the computer or module Ficht of one Evinrude Eco Tec 115 hp 2001. I had a trouble with the computer and in this country noone repair this computer. Thank you for the information that you bring me!!.

@timvogel2407

3 ай бұрын

Here you go: www.dfitechnologies.com/

Watch this video too (shows how to install an EMM): kzread.info/dash/bejne/dHd7z86Dg86YdMY.html Here is the thread that discusses the reason why the EMM needed to be removed: www.thehulltruth.com/boating-forum/996809-evinrude-ficht-intermittent-no-start-solved-3.html The key excerpt is below: I have a 2002 225HP Ficht outboard on the boat I bought last year. It ran great for the first couple months. Then, on multiple successive trips, just died each time. No warning, motor simply shuts off and boat coasts to a halt. Happened at low RPMs (in the channel back to the marina) and then happened twice at cruising speed (about 24knots) out on the river. Each time, no warning lights would show, no alarm--motor just stops. Each time waited about 7 minutes, and motor restarts as if nothing had happened. Had a guy (local Evinrude expert) come look at it--didn't see any fault or engine codes. Did notice a "no oil" fault from very early in the motor's life. Replaced a worn throttle bushing. No problems for the rest of the season (another two dozen trips or so). Now this year, I put the boat back in the water, started up fine and ran great for about a half dozen trips, then, same problem on two successive trips. And then the kicker was last weekend--motor died at 24knots in the main channel, but three warning lights came on steady (not blinking)--"no oil" "check engine" "hot water"--referred to in this thread above as three-finger salute. Removed cowl, tilted motors, checked water intakes (were clear), added oil, and waited. Every time I would turn the key one position to restart, the self-check would perform, and then the three lights would come on steady. I did notice that gradually over the course of the 60 minutes or so I was sitting there (at anchor) that the amount of delay between the self-checking completing (all four lights come on, blink and sound, and go off), and the "three finger salute" would increase. Got to the point where the delay was roughly a full second. By then I called for a tow. Next morning, motor started up fine as if nothing had happened. Yesterday, took the boat out and ran around for about an hour, no problem, came back in to the gas dock, fueled, went to start and --nothing at all, just the three finger salute. Removed the cowling, tilted the motor out of the water, waited 15 minutes, and boat started fine and made it back to the slip. I plan to call DFI on Tuesday. This thread suggests a number of possible solutions--cooling lines to EMM; stop/ign relay replacement; neutral switch on the binnacle mount; bad stator. I'll see what DFI says, but given a comment I read about historical heat issues potentially causing problems later (remember "no oil" fault code from years ago) and the three warning lights, I'm leaning towards thinking this is a EMM issue. I'll repost when I have more info.

What is the name of the place to fix it or the phone numbre need my to repair

@timvogel2407

4 ай бұрын

DFI Technologies. It was about $700. www.dfitechnologies.com/

How much The charge to fix urs

@Redantz864

2 ай бұрын

Mine was 1200

Where did you fix your emm I have one need can you send me the link or address

@timvogel2407

2 жыл бұрын

DFI Technologies. www.dfitechnologies.com/

Does anyone have contact info for dfi industries

@timvogel2407

Жыл бұрын

Here you go: www.dfitechnologies.com/

@flatsfisher1

Жыл бұрын

@@timvogel2407 thank so much gotta get back on the water hopefully they can help mine is weird but was verified that emm is the problem

Here you go: www.dfitechnologies.com/