Let us know about your polishing project or any products you used not mentioned in this video. Here is the Part 2 video of the products you recommended in the comments to try: Polishing Aluminum Wheels: 4 Products Tested 1 Winner🏆 kzread.info/dash/bejne/ep2svNZ-f5PJhKw.html Comments suggested: White Diamond, a re-try on Zephyr with a 3000rpm grinder, and a new product on the market! Flitz was suggested too, but immediately argued by others to be a waste... 👀 Check it out!

@johnpavia3759

3 ай бұрын

Uui😅

@johnscheffler1514

2 ай бұрын

Nice looking rim and tire set up. 👌

If you ever have an entire week with nothing to do lol, wet sand the wheel with 220, 400, 600, 800, 1000, 1200, 1500 and 2000 grit. Then polish with the Mother's and then the Blue Magic. I did that on a set of wheels back in the day and they looked chrome when I was done. Then I said I'd never do that again.

@CruisingTheLand

2 жыл бұрын

Lol.. I love your final sentence."Then I said I'd never do it again" I agree with you, the outcome is amazing, but the labor involved! Been there. That's why I now go drill, cutting pads and minimize the labor... sure its 80% of perfection but at least you still have 80% of the weekend left...

@Mryiyo209.

Жыл бұрын

Lmao I said the same thing

@stephenwhite5444

Жыл бұрын

Just pay someone $1500 lol.

@r32marcus

Жыл бұрын

Did you do that all by hand? Or were power tools involved?

@6thGearGarage

Жыл бұрын

@@r32marcus I didn’t have any power tools back then, did all 4 by hand 😵

After years of polishing aluminum semi wheels for years, I can guarantee you the zephyr is going to give you your very best result. The problem being your drill is not going to work. You can use a 3000 rpm grinder but preferably a 6000 rpm. That alone with some easy prep work could have those polished to near mirror finish in no time flat. The very best prep is aluminum brightener or "acid" pre polish. If they are pitted or have curb rash you will want to sand aswell.

@CruisingTheLand

3 жыл бұрын

Hi Matthew, good advice. Only for the vast majority of DIYers, having a 6000rpm grinder is unlikely. Also the semi wheels have space to work with, these 15" wheels don't have much space to get all areas.What brand grinder do you recommend? I will post another video for those that have or want to give buy a grinder. Just like in detailing a car, good old fashion elbow grease, is no comparison to an orbital polisher, and especially for aluminum wheels, you want to generate spinning speed and heat.

@matthewneyens6499

3 жыл бұрын

Ive got a Dewalt 3000 and a makita 6000. There are "arbor bits" you can get to take the wheel out from the body of the grinder. For just cleaning them up nice a 3000 would be sufficient in my opinion. I totally understand where you're at though. I started out polishing my trucks with whatever I could get my hands on when I was a kid starting out.

@359trucking5

3 жыл бұрын

Same here I'm 16 and been doing it using renegade and matchless for 3 years or so and sanding figured out how to get out white lines on flat surfaces too like boxes and fronts and backs of fuel tanks

@359trucking5

3 жыл бұрын

I run 8500 sometimes but usually 3500 need a 6000 grinder

@jdwisdom9433

3 жыл бұрын

tHANK yOU, Now we know! JD

Back in '67/'68 I was stationed at a USAF base that had many VIP planes. Needless to say we polished A LOT! We found the easiest way to remove the black after polishing, was to sprinkle flour on the first wiping cloth. It absorbed the black rather than relocating it. Then us another clean cloth ,for final buff.

@CruisingTheLand

3 жыл бұрын

Nice. Ok the flour trick. Will give it a go.

@user-jm5gk5wc5q

3 ай бұрын

​@@CruisingTheLandhow did that work out

The Zepher wheels and compound is a TON of work!! I’m a detailer and I quoted a horse trailer to wheel out for 3000. Bro OMG. It literally took me 3 weeks and went home black from head to toe with aluminum compound dust. It was an easy 5000 dollar job

These rims are American Racing (Gambler) model AR-52. They were designed to have a “Machined finish”, Not a polished rim like let’s say a Weld Super Single 2.

Hahaha! Power one, Power two... got me laughing out loud with my morning coffee... Thanks.

The wife came home with new rims from junk yard for her g35 infinity,I looked and looked to find best videos to wat by for the best product cause I know aluminum is not resist to polish from expierance!thank you for doing the dirty work and the sequence in which the final product is excellent

Back in the mid 80's when I was in high school and mini trucks were really popular, I had taken the old 1971 Datsun truck dad gave me, and detailed the engine. Those old Datsuns had a lot of polishable parts on the engine. I started with the valve cover and sanded the corrosion and some of the casting imperfections out of it. Then worked my way to finer sandpaper. Being I was new to metal polishing, I tried many different products and techniques. The best I've found to use on your first buffing and even 2nd and 3rd is the Mothers brand aluminum polish. It seems to get the initial polish to the surface the best. The Blue Magic is great for the final to give more of a mirror finish. Its like my auto shop teacher said, there's nothing like the shine that aluminum has compared to chrome. A good polished aluminum engine detailing looks awesome. I eventually polished every piece of aluminum you can see when you opened the hood. People said you could eat off my engine! Lol. 😋 It did take time to get it "perfect". Many times after school and work I would hand polish all of it. Each time looking better and better. Great video of your findings of products and techniques. The key is the sanding working your way up even to 1000/1200 grit. The buffing process is alot easier too. I have revived CD and DVD disks by sanding them and working up to wet sanding with 1200 then use a buffer on a bench grinder. I have a bar of rouge made for acrylic polishing and it makes the disc shiny again. Blue Magic works also. You just need to be careful and use light pressure on buffing wheel or you'll start melting the acrylic/plastic and ruin it. Keep the disc moving, don't hold in one spot on the wheel.

Nothing beats the zephyr polishing. First off youre not using the correct wheel with the emery rouge you should be using a sisal wheel and secondly youre not spinning the drill fast enough. If its done correctly it makes short work out of it with minimal effort.

@jasoncole2107

3 жыл бұрын

^^^^^^^This is all true!! You can also use a loose leaf cotton wheel with white diamonds and it will be like a mirror! But you need an actual buffer for sure!!!!

Purple Power 1 Gallon Aluminum Brightener 4120P. Start with this and it will make things go faster. Use gloves, eye protection and a respirator.

@CruisingTheLand

2 жыл бұрын

Good tip. Will try

@RisingMoon697

2 жыл бұрын

@@CruisingTheLand I just used it with a green brillo pad. You can order the brightner from orileys auto parts. $17 a gallon. I cut mine 50/50 with water.

@CruisingTheLand

2 жыл бұрын

I have some aluminum wheels that have been sitting on the side of the house... some 16s Ultra wheels that are oxidized. You are inspiring me to post a video trying the Purple Power and polish these wheels...

@RisingMoon697

2 жыл бұрын

@@CruisingTheLand If the 50/50 mix is struggling then go full strength. You know it's working if there is a thin white foam. I started mixing it 1 to 4 and worked my way up in strength. I put it on dry metal. Don't rinse first.

@CruisingTheLand

2 жыл бұрын

@@RisingMoon697 got it. Going to order it tomorrow.

1. White Diamond it's what most truckers use. 2 Flitz works good too. But my main go-to is white diamond, its great even just by hand.

@CruisingTheLand

3 жыл бұрын

So in the part 2 followup video, we tried some suggested products, one of which was White diamond and it performed poorly compared to the others.. That video is pinned to the first comment or in the description. Blue magic was much better, easier and brilliant than white diamond 💎

@satyavratadas1640

2 жыл бұрын

White diamond for me as well it literally pulls the black out of the aluminum effortlessly and turns to mirror super quick

Wd-40 is a good way to get tar/tack oil off of aluminum without scratching them up. Takes awhile but it works. I use it on my uncles dumptrucks then wash them with dawn or some wheel cleaner to get the greasiness off.

i run a roll off truck hauling commerical trash and i only use zephyr pro 40 and all my wheels sparkle one of the best i came across so far

@CruisingTheLand

2 жыл бұрын

Yes the Pro40 is a really great polish. I found the Blue Magic to be same.

Look at white diamond metal polish. I polished a 23 year old pontoon. Both sides, it had sat in a carport with the sun shining on out without moving since 2008. I know this becsyse it was my grandparents. I used white diamond Abd was completely finished to a mirrored shine in less than an hour. It was unbelievable.

Order some Gord's aluminum, chrome & stainless/cleaner, polish and sealer. I used it on a set of 15 year old MT wheels and it worked great.

This Generation is all about less work better out come I get it but some times well most times you get what you put in to something just like you get what you pay for. I spent close to 12hr Polishing my forks on my bike it was nice seeing the difference when done People still ask me who done this for me when I tell them I get that look haha Hard work always pays off IMO Cruising The Land My comment wasn't pointed at you your doing the hard part finding what works best for you new sub thanks

i have a lot of alluminum to keep up and something i learned from the best pollisher around....after you pull as much black as you can off starting to shine...but little bit cloudy [ no matter the brand of polish ] finally as shiny as u can rub it.... take regular white cooking flour [ gold seal ] and a new microfibre cloth rub down polished area blow off and notice the shine doubled i also use the flour as a touch up when im lazy....

@CruisingTheLand

3 жыл бұрын

Will try that! Just got another set of aluminium wheels in.

I know a lot of truckers and they keep their aluminum wheels like chrome with some stuff called Wicked and elbow grease. That and a ball is perfect...!

@CruisingTheLand

2 жыл бұрын

I will search for wicked and try that in my next video!

Silvo on Aluminum throttle body works wonders!

take a 3/8” longer bolt and cut a 1” slot in one end,from the end, then cut Emory cloth down to that cut length. Put it in the drill and wind the cloth in the same direction as your drill spin. Keep centered at higher speeds. Acts like a honer

I don’t use a buffing wheel at all anymore for anything but the lip of the wheel. Just soap and water and I start with 320 then 400, then 600 and finally 1500. I then use the soap and water with the mothers and 2000 grit. I finish with mothers and cheap paper towels NOT the good stuff. The cheap stuff works better. With a silicone sealer to top it off. I use a combination flat and rounded wood rasp file for severe curb rash and sand out the file marks with 200 grit. To get to a jewelry like, wet looking mirror finish, in one complete process from start to finish without wandering around. It’s a dirty laborious process No matter What that takes about 10+ hours per wheel that’s in rough condition. Just did a set for my Chevelle and they look show quality after thirty years of being beat on. If they weren’t unobtainium I wouldn’t have bothered. Those wheels are good for a truck type finish though. I don’t think I’d go any further either.

@CruisingTheLand

2 жыл бұрын

Wow, thats dedication! 10 hrs, x 4 wheels is a full week's work! Wheels can be the wow factor on a classic ride, so on a valuable car, its worth it.

I have used Blue Magic for years it is the best product for aluminum I have found .

@CruisingTheLand

Жыл бұрын

Yep.

Just did my wheels.. They were about as bad as yours. White vinegar really helped get the oxidation off. I used scotch bright pads followed by a power ball and mothers. They look fairly good.

I have polished my aluminum wheels to mirror finish using sandpaper but you have to wet sand. I used warm water and just a splash of dawn dish soap for lubrication in a spray bottle and worked all the way up to 3000 grit sandpaper it was alot of work but results were awesome then I taped off the wheels and painted the cut outs which were original gun metal gray with VHT blue anodized spray paint which is unbelievable and BTW if you go for the anodized color coat paint you have to spray with silver base coat first or the anodized effect doesn't come thru I get compliments on them everywhere I go nobody believes that they are the stock wheels on my silvedado. Alot of work but the sense of accomplishment is worth it

@CruisingTheLand

3 жыл бұрын

That actually sounds awesome. Do you have an Instagram or somewhere we can see pics of the wheels? I may do an update video, just picked up some new Wheels, and try a couple suggestions. May even try the cutout idea like you are talking about. Aluminum wheels are great. You can pick some up that are 50 years old, and bring them back to like new! I buy them for $100 and revitalize them. My 14.5 wide super deep dish ones that came off a K5 Blazer (with Mickey Thompson swampers) i bought for $300, brought them back to life, and enjoyed them for a year.or so, then sold them for $1400 kzread.info/dash/bejne/iamglbSFh6uxncY.html

@wadebuck69

3 жыл бұрын

Awesome about enjoying wheels for awhile and turning big profit. And sorry but no I don't have Instagram or Facebook. I also bought the Zephyr polishing kit and I agree that it is alot of work and very dirty I had to wear gloves a respirator and long-sleeved shirt and it was still a mess. I put in many hours and tried multiple methods and the wet sanding worked best and I finished the polishing by using some never dull wadding dipped in mothers aluminum polish and worked that in a bit and then a 6" harbor freight dual action polisher with a finish buffing pad that I pre loaded with some mothers. It is cool to watch videos that others have had the same kind of trials and tribulations that I have. I appreciate you and if I can figure out a way to post some pics I will get back with you

He should’ve put the degreaser on it first to get better grip it makes the metal extra crusty after hit it with that red chock polish and the grinder as you claim 6000 RPMs and have a green chock polish to finish it up once you don’t see any black from finishing using a red chock then you hit with your softest polisher wheel and the green chock are wonderful mirror finish used to work at a truck stop and these truckers are serious about their polish

Ok , Try mother’s Billet Metal Polish, it works way better then anything you have tried , Thanks for the video

I am glad to see you used the Blue Magic, I been using that for years. Great video.

I’ve always used Flitz and a high speed drill and polishing wheel turns out great every time!

Flitz is the king of metal polishing, especially aluminum rims or wheels. The secret is in the pre-cleaning.

I just finished polishing wheels on my transport truck that had a million miles. I used the mothers mag and aluminum polish. I my case my job was alot easier when I stopped using Microfiber rags, and just used white terrycloths to apply and buff it off. Took me approx 2.5hr to do all 6 wheels by hand.

@CruisingTheLand

2 жыл бұрын

Nice. Sometimes a good ol Terrycloth will get the job done. Maybe being a little more rough helps when polishing by hand. You are a trooper for doing a transport truck wheels by hand. I deifinitely would have given in to a drill.

@xpally944

2 жыл бұрын

@@CruisingTheLand my intentions were to do a little spot just to see what it would've looked like, then I got a little carried away lol

Bigger battery does not provide more power it provides longer run time.

@CruisingTheLand

3 жыл бұрын

I have tested it... the bigger battery give more torque, not speed.

Audience, I'm going to go with all black wheels on my all black jeep wrangler with a lift kit. You did a good video. Kudos...

I’ve had really good luck with flitz polish and the power ball.

very clear and articulate, detail where needed, not enough material of such quality found elsewhere, Thank you!

I always use mothers for aluminum , And don’t let mothers dry up the wetter the better just like when you’re buffing a car you don’t wait till the buffing wax dries you’ll get black like you won’t believe yes it would be messy

@CruisingTheLand

2 жыл бұрын

I found mothers was best on chrome, just like you say, dont let it dry out.

Thank you so much for your invaluable information, highly appreciate it, keep it up the outstanding job, have a great day.

Great video!!! Took all the guessing out the work. Thanks 🤙🏽

Being a metal polisher and paint correction professional, this was quite endearing to watch :) that drill DOES not have the guts to manipulate the heat it requires to polish metal.. yes, polishing metal requires heat, that's why theres 3k and 6k buffers. But great job nonetheless !

@CruisingTheLand

2 жыл бұрын

Thanks. You are right, speed is King for polishing, especially when using the Zephyr.

@marcushennings9513

Жыл бұрын

I notice that most guys that polished all the wheels and brightwork on semi trucks at truckstops would use grinders with different type pads and they would look pretty good afterwards.

@johnnygeorgopoulos4072

10 ай бұрын

Yeah I just attempted to polish a set of deep dish 15x10 Pro Comp Series 69 wheels that came on my truck I bought a couple years ago and just found this out 😅 Used Mother's and their Powerball 2 with my Hitachi cordless (I'm 40, but when I moved about 8yrs ago I literally sold all my good construction tools I obtained throughout the years, so I only have the bare minimum) and while they look a hell of a lot better than what they looked like when I bought the truck (97 GMC k1500 RCSB Z71 with a 6" lift), I still wouldn't consider them to be "polished " lol. I did consider painting them black, but figured polishing would have a longer lasting, and easier to keep look 😅

Came for tips on the centerline wheels on my 66 Chevelle, subbed for the land cruisers. I have 3 fj60’s. Quality content. Thanks.

@xmo552

Жыл бұрын

Mothers had a polish called Billet Polish. It's been discontinued probably because it was very pricey. I spoke to a tech last year and I was told they're bringing it back under a different name but it hasn't come out yet. That stuff was gold! I have some Centerlines from the 90s with the allen-bolt bolt-on center caps, some Centerlines I bought around the year 2000, and some 16" dually Alcoas from the 80s. Their billet polish was literally wipe on wipe off no effort done in 5 minutes per wheel.... and I'm talking about taking a foggy/hazy wheel to chrome mirror in minutes. Wipe on wipe off. I loved that stuff. I manage an auto parts store, one day I tried to clean my wheels in the parking lot and everything else I used actually hazed my wheels. I panicked and tried every product in the store until I got to the pricey mothers billet polish, boom instant restore to as new show shine. I've been a believer ever since. I buy up the old product whenever I can to keep my Centerlines looking perfecto with zero effort.

Great work and info on the issues around how to get aluminum rims polished. I used this info to buy the reccomended items and proceeded with polishing my rims on my 73 Vette ...!!! what a difference! thanks for your time taken to build this video!!! GM

@CruisingTheLand

Жыл бұрын

Awesome! Glad it helped! Time saver, but better yet, great results.

The blue magic works amazing. I used it this past weekend.

@CruisingTheLand

3 жыл бұрын

Glad to hear.. it really does. It also was the best in a follow up video comparing to white diamond and dura coat.

The chrome polish is the best one it has fine grit in it that cuts through the aluminum turning the aluminum rim into a glass light finish

White diamond polish seems to work on my Micky Thompson 2 wheels

For the zephyrs wheels you really need the better airway kit and a variable rotary polisher with a 2” extender, that would make polishing them easier with better results but you’d still have to get the hard to reach nook and crannys by hand or with something else

@michaelford5885

2 жыл бұрын

You DEFINITELY need the full kit , that grinder makes it a night & day difference in effect and effort

Thank you mang! Watching this video help me learn the correct way to polish aluminum wheels! 👍🏼💥

@megaruhe6296

3 жыл бұрын

Who are you? Razor Ramon, chico?

That's right, it's the ants, lol! But, take it from an older dude, Coke changed it's formula some yrs. ago ....it's the "old Coke" that ate nails!!

@CruisingTheLand

2 жыл бұрын

Lol! Old Coke had some bite! Probably the real cane sugar vs corn fructose.

@cheechnchong4347

2 жыл бұрын

Real "Coke" ...😜

Thanks for putting this on. Massive help.

I used to polish my aluminum motorcycle engine side covers with Simichrome on a Turkish towel. It came in a tube like toothpaste. Lotta elbow grease but it came out nice. Now I don't even bother. Have a 1999 Jeep and it's only been washed twice in 20 years.

@savage22bolt32

3 жыл бұрын

I'm getting kinda too old these days 🥴

@CruisingTheLand

3 жыл бұрын

My part 2 to this video and feedback will feature a product that may require the least amount of elbow grease, with great results... I am excited to apply to a set of aluminum rims I just picked up for $100... going to make them look like $1500. Stay tuned!

I've got a set of those exact Wheels, and I can tell you mine are damaged worse than those it looks like somebody sprayed something on them trying to clean them or something that it shouldn't have and the only thing to even put a dent in it so far is 1000 grit sandpaper I got to do that before I can even think about polishing it for real I'd love for them to look as good as yours turned out

Remove the wax and spray clear coat then you won't have to buff all the time just wash and wax every so often.. Great Video..

@topchoppers7980

3 жыл бұрын

Oh firstly that's an off-road vehicle and secondly clear coat chips and peels from dirt and micro fractures due to regular road damage just to start clear coat is not designed for wheels and only used on wheels with base coat clear coat paint hardener and a few other additives to make the paint or clear coat more durable, and resistant to afore mentioned damages, and then thirdly it's very expensive,

Muriatic acid does pretty good on aluminum with little to no labor involved

I use white diamond on my semi truck wheels and tanks. It does very well with no much effort.

Thanks for your video. I had a airplane that was polishing aluminum To wipe it og I used flour to pick up the oxidation.

@CruisingTheLand

3 жыл бұрын

That sounds like a big job!

@manuelcervantes5866

3 жыл бұрын

Did you mix it with water and make paste or how does the flower work?

I've been detailing for over 33 years. The best for aluminum restoration is Barkeeper's Friend. I have a video playlist where I detail a Barrett Jackson Auto Auction Car, and I use Barkeeper's Friend on the aluminum and chrome.

he’s right it won’t be long till you do

I agree with a combination of 1) zephyr and 2) blue magic.. ..yea it takes extra time and awkward with the drill angles with the zephyr but it really pays off.... Your rims would have come out more shiny... I got mine to a mirror finish...

I love the black nails...absolutely gorgeous set!

@CruisingTheLand

2 жыл бұрын

Lol! I have learned to wear gloves now!

Thank you for this video. The explanation was very helpful! Excellent pointers.

@CruisingTheLand

2 жыл бұрын

Thanks!

That ant polish comment was priceless.

@fabgir2010

2 жыл бұрын

ants job :)

I could have polished all four of them out in an hour to a show quality shine using the Zephyr and the right grinder Glover's detail and polishing

@CruisingTheLand

3 жыл бұрын

Hey Glover, but you are a detailer and not a DWYER. The Zephyr kit is pricey, and high speed grinder required. Stay tuned, going to post another product against the Blue Magic and Zephyr with a high speed polisher.

@robertglover8177

3 жыл бұрын

I started out as a do-it-yourselfer having the right equipment is most of the battle you don't need the whole kit to do the job go watch Evans detail and polishing what are the top polishers in the country he will give you the best tips and tricks

@ryandeboer9584

3 жыл бұрын

My vintage UFO has lost its luster, not sure of which planet its bonnet originated from 🛸🔭

The zephyr is definitely the best product I polished my entire boat with it but you need a good high rpm grinder to get the best result and they also sell a rake to clean those wheels so you don't get dirt and whatnot in the wheel

@tacticalty9693

3 жыл бұрын

Must have never tried menzerna. I’ve used keystone, zephyr, renegade, maverick, etc. the best you will get your hands on is menzerna hands down period.

@CruisingTheLand

3 жыл бұрын

So what Mendenhall Product? The rouge wheel, or the SP4500?

@tacticalty9693

3 жыл бұрын

@@CruisingTheLand Mendenhall? If you mean menzerna I use menzerna 439T to cut with, menzerna 480BLF to color with, & p175 to finish with. I use matchless buffs, or Osborn since matchless sold out to them.. hit me up on Instagram @1_wide_obs if you want to see some work I’ve done or want some links to what I use or tips and tricks that will be very helpful to a beginner.

Great Video Bro , Good Narration. ✌

I used to use coke to clean my Brilliam Copper Goof Clubs. I would soak them over night, with very little work after the soaking

Really enjoyed this, gave me the confidence to buy some products. Thanks so much!

@CruisingTheLand

Жыл бұрын

You are so welcome!

Very helpful video thanks ..

Sand and keystone or zephyr buffing wheels is where it’s at if you want a mirror finish

Neverdull is actually an aluminum oxide in a cotton like product. It’s not used to wipe on wipe off it should be applied with pressure and continuous. It will eventually polish any aluminum product to a mirror finish if it is used properly. We used it one command aerospace SH-2F intakes to make them have a high mirror of finish. You are not applying it properly. It does work.

The clay and polishing wheels putting it on a multi speed grinder it goes pretty quick.

Great job, the wheels looks awesome!!

Thank you for sharing this

Good info but not the mirror finish I was expecting for the work involved.

love yer video bro please keep on doing what you do

The drill doesn't produce enough RPM to polish because the heat created helps to cut and polish the rim and rubbing it directly on from the Rouge compound was really a epic fail , then you need a polishing rake to clean the airway pad , you need a grinder to properly polish and you will be SURPRISED how fast that rim cleans up . That aluminum will look like stainless steel or chrome .

Thanks for sharing 👍

"Aluminum" wheels used to be nicknamed "mags" and "alloy" because they are an alloy of two homogenous metals, aluminum and magnesium. Either metal by itself wouldn't be suitable; aluminum is too soft, magnesium is too brittle- but mixed in the correct ratio, you get a strong, lightweight rim.

@CruisingTheLand

Жыл бұрын

That's is cool! Thanks for sharing. makes sense.

@HUBBABUBBADOOPYDOOP

Жыл бұрын

@@CruisingTheLand You're very welcome, young man!

Great video. 💥. I could be wrong but you might have bit of an obsession with land cruisers 😝👍

@CruisingTheLand

2 жыл бұрын

True dat. If you druve just one, everyday, it could become predictable. So nice for a variety, as they all drive different and you always look forward to driving a different one. But I also have a couple cars of the non-Toyota variety.

This will get the views it deserves eventually. Thanks for the tips man! Great video

I use Easy Off oven cleaner. Works fantastic!!

Thanks for the info . I bought all the different supplies about two months ago and have been hesitating on doing the experiment on what works the best thanks for saving me all that time . I am restoring restaurant equipment so I think it will be lot easier than wheels for sure .. By the way it is called Silver Billet not Bullet :)

@CruisingTheLand

2 жыл бұрын

I have a video on restoring my BBG stainless steel grill. Very different than aluminum wheels. Different products. You should check it out. Its in the channel.

Beautiful fleet ya got there

@CruisingTheLand

2 жыл бұрын

Thanks

@CruisingTheLand

2 жыл бұрын

Thanks! Added a couple diesel JDM landcruisers since this video...

should have flashed the wheels with zepp aluminum cleaner 5:1 ratio before the polishing. That’s how I do it in my 18 wheeler rims. After that I rub the mother’s aluminum polish with blue shop towels. But even that takes along time because I’m doing it by hand. Good work tho 👍🏼👍🏼

@CruisingTheLand

3 жыл бұрын

Good advice. I did a followup part 2 video to this one, using some suggested products in the comments. And that 2nd time, used a acid wash to prep the wheels. It didn't make a huge difference, just helped the cleaning process getting grime and debris off the wheels.

I have some of that old product you can have but there's nothing like white diamond metal polish should try and Powerball and cord drill work wonders

@CruisingTheLand

3 жыл бұрын

Watch the 2nd video. White Diamond was already recommended and I tried it. It was actually the worse. If used alone with nothing to compare it to, someone would think it was good. But if you use Blue Magic beside it, it is night and day! Then you'd realize just how bright your wheels can become. Blue Magic creates dark black tarnish on the microfiber, the white diamond was light grey. You can even smell that blue Magic is very pungent and strong, White diamond is not and smells like vanilla. You want Vanilla wheels? kzread.info/dash/bejne/ep2svNZ-f5PJhKw.html

blue magic is the best bro

The best metal polish is Autosol

Bro... great vid...you got me tired just watching

Looks great! My wheels have factory clear coat on them . Do yours also? Are you taking that off first?

Coke has phosphoric acid in it. Naval gelly is phosphoric acid and it's used to get rust off.

OMG AT 29:50 THATS NOT THE CHUCK OF THAT DRILL GRINDING ON THE WHEEL IS IT...ZEPHYR BY FAR WOULD BE THE CHOICE..

The best paste polish I have used is semi-chrome I used to have old Triumph motorcycles that had high polished aluminum covers and it would make them look like chrome with a blue haze maybe more like nickle shined up also flitz worked pretty good but not as good as semi-chrome both of those put mothers mag wheel to shame not even close just for a comparison the never-dull was ok too it just did not go as far and was not able to be worked in like a paste.

@CruisingTheLand

2 жыл бұрын

I will try semi chrome

blue magic is best their is period

WD-40 works wonders with titanium and titanium only I've found, I use it on my TSR and Ladybird exhaust on my CBR1100XX.... you can spray some on a microfiber and literally as soon as you touch the titanium you'll see anything and everything wipe right off.

@CruisingTheLand

10 ай бұрын

I will have to try that!

thanks for the video i am making my grandson a rat rod but with class lol and i have old school alum mags and i restored one it was very time consuming your video helped thanks

@CruisingTheLand

3 жыл бұрын

Great. Glad to hear.. Polishing wheels is definitely not a wipe on wipe off deal. It takes time, but important to use good products and powered tools to get the the most out of your time.

@topchoppers7980

3 жыл бұрын

No matter what or how you go about polishing it is labor intensive

@topchoppers7980

3 жыл бұрын

And a lot of pressure actually does more harm than good polishing is more about speed than just about anything else keep in mind almost every single polishing process you can do removes very miniscule amounts of material

@CruisingTheLand

3 жыл бұрын

@@topchoppers7980 yes true. I just posted a followup polishing to that one, with some other products...

Just put non a rag Dry It take of the paste your using It takes of oxidation

Your technique maybe easier , but the zephyr 3 stage kit followed by the 40 series . Will leave a mirror finish on the wheels if done right.

what is the correct RPM for polishing aluminum? it is different from paint

u wanna get lighter and finer the polish and brush pad the closer u get to the final stage, then even wax it. the wd40 will get stuff off of car paint with soft cloth without hurtin it but dont think itll polish anythin but 4 cleanin yea. this is very similar to gettin out swirls on car paint from coarse towel scratches. ur just using aluminum polish instead of paint buffin compound and polish..autosol will work for this too

I've always heard the trick to using coke is to couple it aluminum foil as a scrubbing pad. I've never tested it, though.

@CruisingTheLand

3 жыл бұрын

I think the person who came up with that way, was actually on coke.

@Whiskeyjack1771

3 жыл бұрын

@@CruisingTheLand You may be entirely correct. After all, that method was a very common urban legend in the 80's, and the decade of decadence is known for its love of that drug!

Good idea on using steel wool with the mothers, I usually cut it wit gasoline.

Very wholesome video!