2.0 version Long travel with further pivot points, adjustable coil overs, with specific spring rates. The overland community thanks you in advance 🤙

Great video guys, nice and clear explanation of everything going on.

Thanks! Great vid. Much less intimidating a job than I suspected.

Great job on this video. Really helpful! Thanks guys.

awsom I cannot wait to get my kit for my off road trailer.

I liked your presentation,clear,and straight away. I will look to your company for my future purchase.

@etrailer

2 жыл бұрын

Thank you for the feedback! Check out the following link for more information on this axle-less trailer suspension system. www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/A12RS440.html

Great product to upgrade an older trailer to even better than when it was new, even better for a new trailer and it looks like it will be a weight saver too.

@etrailer

3 жыл бұрын

These are a great replacement for a factory axle and leaf springs. With this kit you will have higher ground clearance because you don't have an axle. www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/A12RS440.html

I need a 6 inch drop. I wonder if this will work with air bags to lower my trailer even more

can these Axle-less systems be used on Airstreams?...specifically a 1970 Overlander? I find it appealing but not sure if compatible ???

That's a clever way to do walking beams and leaf springs bouncing make pulling trailers hard on your automatic transmission

Do you make these for 10 to 12K axles that use tandem duals?

In the UK we've had indespension units for 50 years or more, it's very rare to see a non-commercial trailer with an axle.

Use stover nuts and loctite! After it's installed I'd also put a couple 1/2" tac welds from plate to frame and she's good for life

@etrailer

3 жыл бұрын

You can use the methods that you are referring to if you don't want to be able to remove it easily for maintenance or replacement. www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/A12RS440.html

These are only good for lightweight use. Anything that will exceed 5k lbs use axels. These are also prone to swaying. Especially after they have been used for a while. They are good for adventure/teardrop type campers. Very easy to raise or lower them with this setup. Make sure to elongate the holes drilled for them and test before welding. You might find yourself pulling a trailer that is pulling to the side.

@robertheinkel6225

2 жыл бұрын

Since this is a 3500 pound rated axle, it will not work on a five thousand pound trailer.

@pnwchris2000

2 жыл бұрын

You can use this design by Timbren for a number of uses that exceed 5,000lbs or more. I was quoted and plan on buying their products for my Black Iron/Full Framed Tiny House on Wheels. I’m just waiting to catch up on other stuff before I redo the suspension for my trailer. I own 8 old trucks as well so they take up a bunch of my money haha.

@NoName-ml5yk

8 ай бұрын

Timbren has a 7000 lb model.

These suspensions do require lubrication! you must lubricate them if you want long life out of the pivot bushes, that is why there is the grease nipple in the bottom of the trailing arm

So great! I've needed this info for a while.

@etrailer

4 жыл бұрын

These are really cool. You won't have to worry about bottoming out because there's no axle. www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/A12RS440.html

i’m ordering a set today for my off-road trailer.

@etrailer

3 жыл бұрын

We love hearing this! Let us know how you like them by leaving a review on our product page. www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/A12RS440.html

i have seen this work... very impressive and just about faultless 🤠

@etrailer

3 жыл бұрын

Thank you for the feedback! We are very happy with the performance with this kit. www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/A12RS440.html

How much speed can this axle less things handle?

Fantastic 👍

@etrailer

3 жыл бұрын

Thank you for the feedback! Check out the following link for more information on this kit. www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/A12RS440.html

Squirt some water on the hole ...you can cut right thru with half inch bit no sweat ... will be using these axles from now on..

a tip instead of a magnet use a piece of tape inside of the boxend side of a wrench

@etrailer

3 жыл бұрын

That's not a bad idea either. We've also used a paper towel to hold it in the wrench or socket. www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/A12RS440.html

a piece of tape on the back side of a wrench to hold the nut works well. :)

@etrailer

3 жыл бұрын

Thank you for sharing this with us! It's always good to learn new techniques for future installs. www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/A12RS440.html

Love it. Simple but affective design. My only struggle on my overland trailer with a current dexter axle is ordering the right height. I cant figure out if standard or 4” lift will be appropriate. Trailer is kind of tall with 32” tires.

@etrailer

3 жыл бұрын

You may be better off going with the 4" lift axle-less suspension so that you have extra clearance for overlanding. www.etrailer.com/dept-pg-Trailer_Leaf_Spring_Suspension-pt-Axle_Replacement_System.aspx

How do you go about torquing the pivot bolt, instructions say 420-470lbs?

Just go to a torsion axle. That's all this is with a longer swing arm. There is an axle to cross brace the frame. Remove the square tube and see how well it works.

It's a good set up but that doesn't work in corrugation outback Australia

I love that you use a little 12 volt drill to drill :) I always have friends making fun of me for using my little 12v drill

@etrailer

3 жыл бұрын

They always get the job done for us. www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/A12RS440.html

i installed these as a third axle on my short bus for towing. used 7k rated set an i dont have amy complaints

@etrailer

2 жыл бұрын

Thank you for sharing this with us and others! This is a great kit and it's very straight forward to get installed. www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/A12RS440.html

These look really good. One of the things I worry about with my leaf-sprung cargo trailer camper is breaking springs when camping in remote areas off-road. Do you know if Timbren has tested these to failure? Any idea what the “weak link” is and what good emergency repair parts would be?

@etrailer

3 жыл бұрын

This kit would be great for exactly what you are wanting to do! There is nothing to get in the way when going off road or to get caught in the leaf springs. www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/A12RS440.html

@hgj2019

3 жыл бұрын

@@etrailer thanks! I’m folding these axles into my plans.

the loose fit tube steel cross member and two bolts one side look like an ineffective stiffening arrangement

@brooksrafael5246

3 жыл бұрын

A tip: watch series at Flixzone. Me and my gf have been using it for watching a lot of movies recently.

@reubenhenry4333

3 жыл бұрын

@Brooks Rafael yea, I have been watching on flixzone for since november myself :D

You need a magnetic drill, would make the install so much smoother and quicker. Just a small one.

@etrailer

2 жыл бұрын

That type of drill would make it a bit easier with drilling the holes in the frame of the trailer. www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/A12RS440.html

I think they will work well for a drop deck trailer , 4 should be good enough in the 3500lb that way 10k weight will be perfect . Trailer will stay flat even parked with a load no tilt or tongue jack need. I've built other trailers but the full axles for drop ones won't work to well.

@etrailer

3 жыл бұрын

Thank you for sharing this with us. This kit will be great for your situation. You just want to be sure that you get the kit that is rated for your trailer. www.etrailer.com/dept-pg-Trailer_Leaf_Spring_Suspension-pt-Axle_Replacement_System.aspx

Great vid, but the over spray looks sloppy. It would have only taken a min to tape it off. Or paint it ,then heat gun it, before u install it

I’ll be putting these on a tandem axle Cougar 22RBSWE.

@etrailer

3 жыл бұрын

Awesome! We love hearing this. You just want to be sure that you are with in the weight capacity of this suspension when the trailer is loaded. www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/A12RS440.html

@henryhester1897

3 жыл бұрын

etrailer.com it’s a dual axle 5,700 GVWR with off road tires 9x31”

Use Cone bits to step up size.

I run timbrin bump stops on the front ends of my plow trucks and there fucking amazing they take so much weight off the suspension and the rubber timbrins take the weight and I run road masters in the rear to take the weight I took of the air bags off all my trucks and run them on the rears now best decision I ever made and they also take body role out

@etrailer

3 жыл бұрын

Trimbren bump stops are a great add on for the front suspension on trucks that have a lot of weight such as a snow plow. Thank you for sharing this with us and others that might be looking for something to solve a similar issue.

thank you for detail video great ideal setup like will work 3500kg 4 wheels car trailer?

@etrailer

3 жыл бұрын

We are happy to help! You will need a kit that is rated for more weight. Check out the following link to see the kit we would recommend for your set up. www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/TASR5200S03.html

What about tandem applications? Is there a way to equalize the pairs or would it be independent?

@etrailer

4 жыл бұрын

For a tandem trailer you can use two sets of the Timbren systems however a third set for triple axle trailers is too much. The third axle will scrub too much for the Timbrens take. They'll be independent of one another. Another option for tandem trailers is the Silent Ride www.etrailer.com/dept-pg-Trailer_Leaf_Spring_Suspension-co-Tandem_Axle-pm-Timbren.aspx These replace the suspension of a tandem trailer but you still use your standard axles. -Chuck S

A person could do a lot with these things....❓ like use it for the suspension on a bike build. Or other really cool projects.

@etrailer

2 жыл бұрын

I suppose you could use these for many different projects. We do know that people sure do love them for swaping their trailer axles. www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/A12RS440.html

Wonder how I could work around not using the cross tube and build a drop down trailer.

@etrailer

Жыл бұрын

What you're wanting to do is beyond our expertise. We'd recommend finding a local trailer shop that's experienced in fabrication.... www.etrailer.com/Trailer-Axles/Timbren/A12RS440.html

Axless system but it has an axle in the front, or do you call a a "stability bar" and then each side is held in with six bolts so now you're weakening the frame by drilling these holes all over the place in it so in a few years the trailer will break in half from all the rusting, then what happens when all of the rubber cushions dry rot

@geographyinaction7814

3 жыл бұрын

Re-watch the video...

This axle is too heavy for my application, but I found one that was suitable for a lightweight trailer weight.. Designing a hard side pop up motorcycle camper I had to use that style to cu enough weight to make it usable.

@etrailer

3 жыл бұрын

Thank you for sharing this with us! It sounds like this kit will work great for you! www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/A12RS440.html

@geographyinaction7814

3 жыл бұрын

Sometimes the 3500 is a necessary selection, as the smaller Timbren may not fit the hub you are using. I believe you can have the 3500 de-rated, if that makes sense.

What wall thickness of square tubing should you use for the crossbar ?

@etrailer

3 жыл бұрын

We used scare tubing with 1/4" wall thickness because we wanted it to be stout enough to handle the loads we are going to carry. www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/A12RS440.html

How do you know what hubs to buy to fit the axel? I don't want to buy the wrong hubs

@etrailer

4 жыл бұрын

You need to make sure that the hubs use the same bearings and grease seal as the spindle. You can either find the part numbers for these on the bearings and grease seal directly or you can use a digital caliper and measure the locations on the spindle that those parts ride to the nearest thousandths. Below is a link to our selection of hubs and drums as well as a link to an FAQ on bearings and seals. If you still need some assistance you can reach out to us directly here www.etrailer.com/customer-service.aspx www.etrailer.com/dept-pg-Trailer_Hubs_and_Drums.aspx www.etrailer.com/article-categories.aspx?productgroup=Trailer-Bearings-and-Races

How well does this set up work off-road? I’m starting a trailer conversion and if this set up can handle light off-road I may have to grab a couple

@etrailer

2 жыл бұрын

Many people have used this for off road trailers. It is really nice because you don't have to worry about the axle hitting anything when you are out on a trail. www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/A12RS440.html

You may not have an axle transferring energy from one side of the trailer but you do have the cross piece

@etrailer

3 жыл бұрын

It will depend on how your trailer was built but on this trailer the cross piece was higher than the trailer supports. www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/A12RS440.html

@mrfish7357

3 жыл бұрын

Can you elaborate on the difference in travel between the axle less system and the leaf spring system and ride characteristics which one would be a softer ride?

This would be cool to put on the very end of a trailer to keep it from dragging on steep driveways leave it raised above the road .

@etrailer

3 жыл бұрын

We have a few skid wheel kits just for that! Check them out in the following link for more information. www.etrailer.com/dept-pg-RV_Skid_Wheels.aspx

Is there a maximum speed it can handle up to

@etrailer

4 жыл бұрын

The Timbren Axle-Less Suspension can handle highway speeds so you really just need to check the speed rating for your tires and be sure not to exceed that.

I see that you bolted everything to the trailer, would you not recommend a weld on application?

@etrailer

4 жыл бұрын

This kit is going to be a lot easier for most people to get installed. It is harder to install a weld on kit. www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/A12RS440.html

Will this work on a aluminum trailer from northern tool 40"x48"

@etrailer

Жыл бұрын

We have seen these installed on a trailer from Northern Tool. You just want to be sure you are mounting it to at least a 2x3" trailer frame. www.etrailer.com/Trailer-Axles/Timbren/A12RS440.html

how does this compare to a torsion axle? i have had good luck with the torsion axles on my 10,000lb work trailer. had lots of wear and maintenance on the leaf sprung axles on my car trailer looking to change at some point.

@etrailer

3 жыл бұрын

These axle-less systems are a bit different than a traditional torsion axle. The axle-less system is nice because if you hit a bump on the one side of the trailer, the other side of the trailer does not recoil from the bump. I have provided a link to the 5200 lb kits that we carry. www.etrailer.com/dept-pg-Trailer_Leaf_Spring_Suspension-pt-Axle_Replacement_System-gw-5200_lbs.aspx

My boat is 6,5 tones and I would like to use your Axle-Less Trailer Suspension with drop. Do you make them for these type's of heavy loads? Thanks

@etrailer

Жыл бұрын

Assuming you have a tandem axle trailer, two sets of the Timbren # TASR7KS02 Axle-Less suspension assemblies would provide up to a 14,000 lb capacity with a 4 inch drop. Hope that helps! www.etrailer.com/Trailer-Axles/Timbren/TASR7KS02.html

@olliebri

Жыл бұрын

@@etrailer Great help. Thank you!

So this suspension works basically like an independent suspension with no axle tube to get beaten and bent ?

@etrailer

3 жыл бұрын

You are correct. It helps to give you more ground clearance. www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/A12RS440.html

Are these adequate for boat trailers?

@etrailer

7 жыл бұрын

The Timbren Axle-Less Trailer Suspension System will work well on a boat trailer. It has a heavy-duty steel construction which doesn't make it the best option for a salt water application, but it does have a black powder coat finish that helps to resist wear and corrosion and will hold up better than a standard painted axle in a saltwater environment. The Timbren Axle-Less system will have normal wear and tear as long as it is taken care of. The spindles use the EZ Lube feature which allows you to grease the zerk fitting without having to take the whole hub off. This is a great time saver option that some people don't even know about. That is really the only maintenance that you will have to take care of.

Basically like the 2win double deck trailers you see here in Europe lol

Is it okay to weld this system in place, or does Timbren recommend not welding? Also, what's the weight rating? Do they make these to handle up to 5k Lbs. each to replace a 10k axle?

@etrailer

3 жыл бұрын

You can weld this system in addition to bolting it to the trailer frame. We have many different sizes available to match what your trailer needs. www.etrailer.com/dept-pg-Trailer_Leaf_Spring_Suspension-pt-Axle_Replacement_System.aspx

Can a dual axle trailer be converted to this?

@etrailer

2 жыл бұрын

It absolutely can! Many people have converted their dual axle trailers to this system and they love it! www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/A12RS440.html

It’s literally a offset axle and hub. Accept you use rubber instead of springs lol Bet this things a fortune too

@etrailer

2 жыл бұрын

This is a sweet system! Those who have this kit on their trailers love it. www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/A12RS440.html

All those holes drilled should have been soaked with anti-rust paint. Also all of the bolts should have had Loctiite applied to the threads. Torque specifications are not enough.

@yoboo6167

4 жыл бұрын

Also, it helps if you haven't been drinking heavily when you are going to be shooting an install video 🤣

was that trailer over loaded or y was the axle on leafspring setup touching the frame?

@etrailer

3 жыл бұрын

The old leaf springs on this trailer were worn out to the point where they needed replacing. www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/A12RS440.html

Do not buy this suspension system I had and it failed a good design but poor( welding wells broke right down the middle of the weld ) the tow job cost me $2500 to get my trailer out of the desert just to the nearest town beware

@RossFeighery

3 жыл бұрын

Yikes, which model did you have and how heavy was your trailer?

@nielmadsen9806

3 жыл бұрын

@@RossFeighery I have the 2500 pound axle the material did not break it’s just a poor welding I would not buy another one

@geographyinaction7814

3 жыл бұрын

@@nielmadsen9806 I've never heard of this, maybe you got the axle's built on a Friday afternoon?

Comprar ???

Question. Why would you use this over a torsion axe?

@etrailer

3 жыл бұрын

The most liked feature that people like with this kit is that if you hit a bump on one side of the trailer, it will not transfer the movement to the other side. This kit is also nice because if one side of the kit gets damaged for some reason, you don't have to replace both. www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/A12RS440.html

Can’t say I’d agree with not needing any lube just because it uses urethane bushings. Urethane squeaks sooo bad if you don’t regularly grease it.

Hello, I own a travel trailer camper with a 9,500lbs GVWR. Will this work with my camper as well?

@jasonmontes9346

5 жыл бұрын

I too have a travel trailer I'm interested in doing this too, did you ever do this to yours or did you decide not to. Thanks

How long does the rubber last and is it replaceable?

@etrailer

2 жыл бұрын

The rubber springs are designed to last the lifetime of the trailer as long as they are not abused and they are maintained. www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/A12RS440.html

The spring set up is actually better. E Trailer you should correct your techs mis information. The rubber/urethane has a progressive rate spring and you can see the tire actually come off of the road due to the slow rebound of a rubber spring vs steel spring. Also be concerned with toe and camber issue when loaded vs conventional .188 wall tube spring axle.

@etrailer

3 жыл бұрын

This trailer is a light weight trailer and did not have a load on it. This caused the bouncing action. This kit performs very well when there is more weight on it. www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/A12RS440.html

@RaceMentally

3 жыл бұрын

@@etrailer I’m familiar. I rate all of their springs.

Very good ,but are you Paul Walker?

Ok for dual axles?

@etrailer

3 жыл бұрын

We have an axle-less system designed for tandem axles. Check it out in the following link. www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/TSR7000T05.html

Do these systems work on trailers that are imersed in salt water like boat trailers?

@etrailer

3 жыл бұрын

You can most definitely use this system to replace you boat trailer axle. You will want to make sure that you get the appropriate size to replace your factory axle. www.etrailer.com/dept-pg-Trailer_Leaf_Spring_Suspension-pt-Axle_Replacement_System.aspx

@fourbypete

3 жыл бұрын

@@etrailer cool, thanks.

Even though this axle-less system looks well built. I feel the trailer is going to be the fail point. With such a large amount of it hanging beyond the brackets it looks like a good spot to bend.

@etrailer

3 жыл бұрын

The cross tube and rubber bumpers will take the majority of the stress from the weight of the load. www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/A12RS440.html

They tried rubber ride years ago the rubber wears out real fast then they vibrate a old idea that sucked

this isnt a review of the product but more of an advertisement for it

@Clickmaster5k

3 жыл бұрын

Ya it seems a lot of companies on youtube don't know the difference between an overview and a review.

I am interested this system for my 2023 intech luna rover with 5 bolt lugs , i contacted etrailer ( adam ) he asked me to call timbren which best fit for my trailer , timbren rep can't recommend instead send me all the specs sheets and im not experts with those specs, im interested with this parts TASR35HDS07 base on your experty can i still reuses all hubs and bearing, according to your video i can . Thanks and hope hear back from you

@etrailer

2 ай бұрын

You'll want to check the linked product page, where we list the bearings that the unit is compatible with. You'll want to make sure it'll be compatible with your existing hubs/bearings. www.etrailer.com/Trailer-Axles/Timbren/TASR35HDS07.html

This is pretty much a torsion axle. The only real difference I see is the method of dampening. I don't dislike it however I would like it better if the spindle and trailing arm were designed so that the spindle bolted to the underside of the trailing arm instead of on top. In the configuration shown here the 4 mounting bolts take up the all the load whereas if the spindle was bolted to the underside of the trailing arm the trailing arm would take more of the weight and the bolts would more or less keep the spindle in place.

@geographyinaction7814

3 жыл бұрын

The plate takes the load, not the bolts.

Tandem axles?

@etrailer

3 жыл бұрын

You can use this in a tandem axle set up. www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/A12RS440.html

How much$$

@etrailer

6 жыл бұрын

Price varies depending on your application. You can view more information at the link below. www.etrailer.com/s.aspx?qry=&furl=-pg-Trailer_Suspension-pm-Timbren

Would these hold up well for slight off-road use and rougher rides if I were to use them on a small tear drop trailer build

@etrailer

3 жыл бұрын

This system would do just fine in light offroad conditions. Check out the following link for more information on this kit. www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/A12RS440.html

@geographyinaction7814

3 жыл бұрын

That is what they were designed for.

The cross tube should extend at least flush to the outside of the side plates to transfer load properly, leaving just inside is just stupid

@etrailer

4 жыл бұрын

It is going to depend on the trailer that this kit is being installed on. If there is a cross member above where the new system will go then there is no need for the cross tube. But, I agree the tube should have been flush to outside of the bracket. Keep in mind the cross tube is not included in the kit. www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/A12RS440.html

@robward7662

4 жыл бұрын

etrailer.com looks like a great product guys , will have a look on your site. Sorry to be picky curse of being a structural engineer.

@etrailer

4 жыл бұрын

We are happy to help! You know what you're talking about and there's no shame in that. Let us know if there's anything else we can do to help.

it looks like that system only has 2.5 inches of travel (which is terrible)

why do you need brakez

@thatbiguy1975

3 жыл бұрын

to stop.... ?

It's not crazy expensive either

@Str8kustomz

4 жыл бұрын

What's the price?

Could you just weld it on?

@etrailer

3 жыл бұрын

You could definitely weld this kit on if you had the means to do so but more people are going to be able to bolt it on with the tools they have in their garage. www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/A12RS440.html

What's the benefit of the square cross beam?

@etrailer

4 жыл бұрын

It is going to add extra support if there is not a cross member on the trailer in line with the Timbren Axle-Less System. The cross beam will not be included, you will have to supply it. www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/A12RS440.html

@hmsrose6230

3 жыл бұрын

It’s cost as much as a used trailer. Lol

These would be worth considering if they weren't so expensive. I could buy a complete trailer for less than the asking price of these.

Holes? You have to be kidding!!! Ya' mean you don't have a welder?

@artsbest1

7 жыл бұрын

What does a welder have to do with creating holes?

@allenmckinney9533

6 жыл бұрын

rod builder not everybody has a welder. This guy is showing it can be done by anyone with simple tools. Bolts are better for anyone that's not a professional welder. I have a welder but I'd still bolt it.

This set up will require an anti sway bar

@etrailer

2 жыл бұрын

We have many people that pull trailers with this system on it everyday and they do not have issues with sway. www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/A12RS440.html

You look like a more smarter, less dorkier version of Ashton Kutcher.

@broccolihart1

3 жыл бұрын

@Rowdy Haahaahaa....great description. This guy could definitely have been a stunt double for Ashton from the movie "Guess Who". Who says there aren't clones walking around?

Or just buy a torsion axle.

@etrailer

3 жыл бұрын

You could also go with a torsion axle. People like how that suspension feels on the Timbren Axle-Less system. www.etrailer.com/Trailer-Leaf-Spring-Suspension/Timbren/A12RS440.html

Lol wtf an axleless trailer that you add a AXLE to...

@nothanks2994

3 жыл бұрын

Your not very bright

@geographyinaction7814

3 жыл бұрын

Watch the video dumbass.

@jeffreyulery2182

3 жыл бұрын

1:45 dipspit