ESP32 Camera module is a powerful sophisticated module used for taking stills, video streaming and also Face Recognition.
Жүктеу.....
Пікірлер: 182
@spencercathey79239 ай бұрын
I can only repeat what the many have said, I needed help, and your video finally solved my problems with this device. A heartfelt thanks.
@aacasd2 жыл бұрын
If the SD card is not used, this board can still be used to add more sensors. This is one of the best videos I have seen which describes how to connect and program an ESP32-cam.
@avirupchakraborty8395
11 ай бұрын
Can you tell me , which pins can I use. I need minimum 4 pins
@noweare13 жыл бұрын
Thank you, you should have more subscibers. You do not waste time. Very high quality content. Very good English also.
@SaravananAL
3 жыл бұрын
Glad you liked it. Thank you too.
@imranmumtaz3409
Жыл бұрын
@@SaravananAL I am programming Esp32 cam using FTDI programmer but getting this error.I have seen many solutions on google but not working.Can you please see the following error and suggest some solution: a fatal error occurred: failed to connect to esp32: no serial data received.
@hydraarjjun1399
Жыл бұрын
@@imranmumtaz3409 getting the same error bro did you solve it ?
@imranmumtaz3409
Жыл бұрын
@@hydraarjjun1399 Yes it was solved and has two possible solutions.When I select the wrover module from board it gets resolved.Secondly I checked programming arduino board from ftdi and it worked fine which shows ftdi was fine.You can program esp32/cam using arduino uno and you can find many tutorials on how to do that from youtube videos.Tell me if any of my solution resolved your problem or not?
@jayadeep8429
Жыл бұрын
ई5cpfbd
@upuldi2 жыл бұрын
The best guide on the internet, very precise. Thank you and keep it up.😃
@benzheng54062 жыл бұрын
Best ESP32 Camera guide I found on youtube
@arnierosen77432 жыл бұрын
excellent job. you make a great instructor. even showed the pitfalls a person might run into if the camer or the programmer had insufficient voltage. thanks.
@adespade119 Жыл бұрын
Just started with this device and you showed most of the problems I encountered.
@raymondmichael49872 жыл бұрын
Most errors covered in this video, well done
@abdullahnasir85352 жыл бұрын
I was facing so much trouble with uploading the code and no video helped me out. They kept saying that this was the solution and that was the solution... but the problem was the timing of pressing the reset button. 8:00 Thanks man!
@stevenelliott98212 жыл бұрын
Your section on problem solving is excellent and extremely helpful. Very much appreciated. Subscribed!
@girishgoudapatil824111 ай бұрын
i was struggling from long to up the ESP32 CAM module with the help of this video i am able to get the output thankyou
@amitabheer2 жыл бұрын
Complete information Nice explanation Perfectly delivered... Thanks for sharing
@techtronix7350 Жыл бұрын
I followed the same steps and it works fine for me thank you.👍
@user-Ivan-Titov2 жыл бұрын
Спасибо из далекой России! Thanks from faraway Russia!
@TechTrendsShameer2 жыл бұрын
Sir. I followed all steps you mentioned but still I am getting below error. A fatal error occurred: Failed to connect to ESP32: Timed out waiting for packet header
@Fiverearning220
2 жыл бұрын
Any solution
@nadakuditigopikrishna658711 ай бұрын
Absolutely amazing sir!! You have all the possibilities and errors. No other videos mentioned this! Thank you for making this wonderful video sir!! You earned new subscriber sir..
@rhoniandjeff74532 жыл бұрын
Thank you for the use of close up on the camera. So many video makers zoom out so you can not see anything. Thank you.
@user-uc8er2ql7t Жыл бұрын
дякую!!!!!!!!! проект з поку врятований!!!!!!!!!!!!!
@flickmew992 жыл бұрын
Thank you sir, but I got 0x105 error init. At first, I can acomplish until serial monitor gives me the IP address, but when I first access it, there just a blank black square. I reset it and then the serial monitor says "camera failed to capture" again and again. I unplug the whole thing, and then I try it again, now the serial monitor says "error 0x105 init" something like that
@kollikiran7437 Жыл бұрын
A fatal error occurred: Failed to connect to ESP32: No serial data received. I got this error..What might be the issue?
@joselitotddc Жыл бұрын
esse vídeo me ajudou muito a entender como conectar a camera, eu estava fazendo do jeito errado e com isso nenhum exemplo de codigo funcionava...
@varanasilalitha86003 жыл бұрын
Appreciate the clear instructions. I however am unable to flash to the ESP32. All the wiring including the GPI 0 to ground was checked a number of times and i still get the message "A fatal error. Timed out for Packet header". also I note that the LED's Tx and Rx on the USB/UART connector do not flash at all. could something be wrong with the camera module GPI 0 pin. Appreaciate your help
@Joel.uno.uno_siete
2 жыл бұрын
have you solve it yet?
@Fiverearning220
2 жыл бұрын
Any solution
@juanemanuelsuarez8432
Жыл бұрын
@@Joel.uno.uno_siete no and you?
@jeniflorance6029
Жыл бұрын
me also facing same problem
@ormej012 жыл бұрын
Excellent video! Very clear and concise
@kritarth12744 ай бұрын
I programmed the ESP 32 cam as you instructed, however, when i try to get still image, i get a jpg file which is empty. It is as if my ESP32 camera is not able to click a still image that is supported. Need help urgently please
@vpthottam2 жыл бұрын
Supper video. Nicely done
@manaspaul19083 жыл бұрын
Dear Sir, After using this instruction I got this is error on web browser --> "Header fields are too long for server to interpret." Please Help.
@umedsingchauhan70633 жыл бұрын
Very nice, explained in detail. Very much helpful
@subhashinisagar902610 ай бұрын
I have error compilling for board AI Thinker ESP32-CAM ...what should I do?
@ankitabhushan60653 ай бұрын
Camera init failed with error 0x105 . How can I resolve it? However I have tried multiple times removing and connecting camera pins. Please guide.
@farhathullamenayath30129 ай бұрын
Thanks a lot, You are a diamond. Finally I solved my problem
@MuzakkiEa259 ай бұрын
Can i run servo in esp32-cam? I tried it but it doesn't work. But with LED flashing and buzzer it works
@nandakishorebilla3213 Жыл бұрын
sir i am still getting issue with eps32 wifi cam it always shows fatal error timeout please fix my problem
@parth78883 жыл бұрын
great explaination, keep up 👍🏻
@bhargavreddy719710 ай бұрын
Excellent sir. I bacame fan for you
@randolfaquino99982 жыл бұрын
if i saw loading up to 100% but failed to follow instructions of pulling the jumper wire and.pressing the reset. Do i need to hard reset/erase? or just do the procedure again?
@miguelco21812 жыл бұрын
Thank you very much, your video was very complete and helped a lot in my project!!
@John_Smile2 жыл бұрын
Hi ! If I don't have an arduino, can I make Cam ESP 32 settings? Is there an option for motion detection? If a thief enters my yard and steals my camera, can I see the recordings on my server / my cloud ?
@techvishalnewsdevelopers309 Жыл бұрын
Yesterday I have purchased and uploaded 2 times. Third time all connections correct and cause fatal error unable to resolve it all. I think cable or ft232rl or esp32 cam is gone.
@cw46082 жыл бұрын
Success! Thank you very much for your excellent teaching.
@user-se4do6ek2j Жыл бұрын
Thnak you! Very useful tutorial! Excellent video!
@dragonexecutioner17152 жыл бұрын
Can we upload the recording to sd card somehow? like it might be inconvenient to always provide wifi to the camera , might be if i use it on any project..thanks for explaining in such detail.
@sltechgalaxy16772 жыл бұрын
Thanks i have all this problems you talk now i solved . it's work
@doro44142 жыл бұрын
Definitelly best how to on eap32 cam. Thanks
@keanesetiawan2 жыл бұрын
exec: "cmd": executable file not found in %PATH% Error compiling for board ESP32 AI THinker I got this error when i try to compile the code, anyone can help me with this? i have downloaded the wrover library and has exctract into the /documents/arduino folder , btu i still face this issue. Please help , thank you in advance
@mayanksaini9524
2 жыл бұрын
Same with me
@soumendas88072 жыл бұрын
Sir I had tried your this project as per your tutorial in several times , everything is working but when select face recognition / face detection my face it is not shows any square on the face and not working, although I have change my cam module with AI thinker but still is not working. I would be really grateful if you give me the solution.
@echandu1167
2 жыл бұрын
havent you got the nts\Arduino\libraries\WiFi exit status 1 fd_forward.h: No such file or directory This report would have more information with "Show verbose output during compilation" option enabled in File -> Preferences.
@xxxXXXCH04XXXxxx6 ай бұрын
doesn't the module gets really hot?? how can you manipulate it?
@huseyinatasoy313 Жыл бұрын
Thank you for you make a great instructor.
@kishorereddy9262 жыл бұрын
sir, I have tried it. Camera streaming is working, but I'm not getting any rectangle around my face. It seems like face detection is not working. Please help me with this
@housewirestv9 ай бұрын
great video, thank you for sharing this stuff with us!
@shree58152 жыл бұрын
Very clear instructions, helped me a lot, thanks, subscribed.
@supratimsaha17452 жыл бұрын
Nice instructions, however it did not work for me after trying 100+ times. Plus now the original code is gone and esp32 does not come up as a WIFI on search, so the device is now useless with nowhere to go. Is there a solution where the device becomes just like new, i.e it can create its own wifi and atleast can work as a cam? please help
@girishchandra6722 Жыл бұрын
I am getting crc doesnt match error after downloading latest version of esp32 in board manager
@sonivvk2 жыл бұрын
I can upload the code and esp32 cam also shows the IP address of the web server but I am not able to open the web server on my browser. The browser page says 'connection time out'. Any solution for this error?
@advertisemedia1509 Жыл бұрын
sir u have used external power source for esp32 cam then how u have down loaded code from laptop
@antox97982 жыл бұрын
i have error detected camera not supported but I selected good camera model and its isnt working. What can I do?
@user-sc8cp1dh4b3 ай бұрын
all code is complied but after pressing reset wifi is not connecting and we are not having ip address
@rajeshmassab6 ай бұрын
Precise and Excellent
@kingsharkgaming98092 жыл бұрын
I am getting 'no programmers available ' And an error :fd_forward no file in directory What should I do....?
@sablightning4819 Жыл бұрын
Can it be possible to have an sms notification when the esp detects an unenrolled face?
@abhirupbiswas56712 жыл бұрын
rst:0x1 (POWERON_RESET),boot:0x3 (DOWNLOAD_BOOT(UART0/UART1/SDIO_REI_REO_V2)) waiting for download how to remove this error?
@venkatesanc1801
2 жыл бұрын
Bro have you cleared this error pls help me I too got the same???.
@abstruse123
2 жыл бұрын
Remove the shorting jumper b/w GPIO0 & GND and then press the reset button
@virendraparihar6982 Жыл бұрын
how to flesh this module or it's chip for reprogramming again
@medicharlaabhijeet20552 жыл бұрын
Can I connect esp32 cam to FPGA board using cp2102 without the use of arduino?
@Manuqtix.Manuqtix2 жыл бұрын
doesn’t work. It keeps on saying a fatal error occurred; Failed to connect to esp32: timed out waiting for packet header
@guido86972 жыл бұрын
would you happen to also have a solution for: "A fatal error occurred: MD5 of file does not match data in flash! " ?
@namburipavankumar8529 Жыл бұрын
I was unable to connect to the website while I was entering my IP address in the popup.
@Artificial.-_-.intelligence3 жыл бұрын
Can i remove and solder directly without 0ohm resistor because if i remove it i wont be able to solder it back my soldering skill is bad
@micmike28 күн бұрын
Thanks very helpful
@simpzic772 Жыл бұрын
im facing problem with serial port not received, how to handle this error?
@wagnergabriel87282 жыл бұрын
wonderful troubleshooting, thank you
@omsingharjit Жыл бұрын
This is not AI thinker so which board is this ?
@dharvikaur4792 жыл бұрын
Thank you sir for this amazing video!
@jonathangadielramirezmarti8224 Жыл бұрын
Does this process needs to be done every time that I work with it?
@afifahtrielestari26372 жыл бұрын
Hi Sir. my serial print is "dl_matrix3du_alloc failed" when i turn on face detection and face recognition. may you help me please? i need your help
@nadarjegansiesgst3268 Жыл бұрын
can anybody help me to select the port...coz it is showing grey and not selectable content in my laptop...I have also tried in my other PC too :(
@TheKvc7 ай бұрын
Very clear❤❤❤
@hk393022 жыл бұрын
Sir it's showing brownout detector was triggered and not showing ip in serial monitor what should I do please help
@andystevens34742 жыл бұрын
Very useful. Thanks for the video.
@digitalnomad8543 Жыл бұрын
Very nice tutorial! I wonder what's the amperage that goes to the ESP32.-CAM If I wanted to provide another power source would 5V 0,5A be sufficient?
@pascalguinet1940
Жыл бұрын
I did measure 250 mA, esp32-cam + cp2102 adapter.
@KLR-3 Жыл бұрын
can this board send the video over serial instead of wifi?
@budirahmani3 жыл бұрын
Learn new module, thank you Sir.
@nation1280 Жыл бұрын
Thank you sir, very nice video,,
@naveennagendra74318 күн бұрын
thank you sir its working welll
@sujoymondal75113 жыл бұрын
Very nice demo
@saurabhrajora1077
3 жыл бұрын
Nice
Жыл бұрын
Great job, keep it up!
@techbymoАй бұрын
Thank you!
@benjosejoseph12133 ай бұрын
Sir we are facing with burnout error how xan we resolve it.
@diakarkhanis15942 жыл бұрын
In ssid & password, can we put our mobile phone's hotspot name & password. Will that work ?
@venkatesanc18012 жыл бұрын
rst:0x1 (POWERON_RESET),boot:0x3 (DOWNLOAD_BOOT(UART0/UART1/SDIO_REI_REO_V2)) waiting for download ets Jul 29 2019 12:21:46 Sir do you now how to solve this error this is is coming after removing gpio 0 and gnd I am opened serial monitor and pressed reset button in esp32
@brizv Жыл бұрын
Sir ji, link in description ? There are none. Please update. Thanks,
@nation1280 Жыл бұрын
Sir, possible to make project call activation camera with this board
@electronic79793 жыл бұрын
Helpful video
@wademartin88223 жыл бұрын
Amazing! Very clear
@hirudikapremaratne2034 Жыл бұрын
So you cannot use FTDI?
@NolanGerald2 жыл бұрын
Great video! Thanks
@31_chinmayshelke602 жыл бұрын
After removing jumper and resetting. In serial monitor it's showing bunch of sign like question mark square arrows etc plss help
@muhammadharis8405
Жыл бұрын
Change the Baudrate
@Himakarbavikaty3 жыл бұрын
Code updloaded but serial monitor i am not getting correct output
@shakerileiwat43413 жыл бұрын
Great video , thank you ❤️❤️❤️
@shaikhmohammadyusuf90183 жыл бұрын
Great video. I am using Arduino Uno to program esp32 cam. But getting the same repeated codes in the serial monitor, also I have powerd my cam with 5v supply. So what should be the problem sir ?
@Artificial.-_-.intelligence
3 жыл бұрын
kzread.info/dash/bejne/f3-dq7Z-o7LdgqQ.html
@sameeiyi8658 Жыл бұрын
A fatal error occurred:Failed to connect to ESP32,no serial data received.
Пікірлер: 182
I can only repeat what the many have said, I needed help, and your video finally solved my problems with this device. A heartfelt thanks.
If the SD card is not used, this board can still be used to add more sensors. This is one of the best videos I have seen which describes how to connect and program an ESP32-cam.
@avirupchakraborty8395
11 ай бұрын
Can you tell me , which pins can I use. I need minimum 4 pins
Thank you, you should have more subscibers. You do not waste time. Very high quality content. Very good English also.
@SaravananAL
3 жыл бұрын
Glad you liked it. Thank you too.
@imranmumtaz3409
Жыл бұрын
@@SaravananAL I am programming Esp32 cam using FTDI programmer but getting this error.I have seen many solutions on google but not working.Can you please see the following error and suggest some solution: a fatal error occurred: failed to connect to esp32: no serial data received.
@hydraarjjun1399
Жыл бұрын
@@imranmumtaz3409 getting the same error bro did you solve it ?
@imranmumtaz3409
Жыл бұрын
@@hydraarjjun1399 Yes it was solved and has two possible solutions.When I select the wrover module from board it gets resolved.Secondly I checked programming arduino board from ftdi and it worked fine which shows ftdi was fine.You can program esp32/cam using arduino uno and you can find many tutorials on how to do that from youtube videos.Tell me if any of my solution resolved your problem or not?
@jayadeep8429
Жыл бұрын
ई5cpfbd
The best guide on the internet, very precise. Thank you and keep it up.😃
Best ESP32 Camera guide I found on youtube
excellent job. you make a great instructor. even showed the pitfalls a person might run into if the camer or the programmer had insufficient voltage. thanks.
Just started with this device and you showed most of the problems I encountered.
Most errors covered in this video, well done
I was facing so much trouble with uploading the code and no video helped me out. They kept saying that this was the solution and that was the solution... but the problem was the timing of pressing the reset button. 8:00 Thanks man!
Your section on problem solving is excellent and extremely helpful. Very much appreciated. Subscribed!
i was struggling from long to up the ESP32 CAM module with the help of this video i am able to get the output thankyou
Complete information Nice explanation Perfectly delivered... Thanks for sharing
I followed the same steps and it works fine for me thank you.👍
Спасибо из далекой России! Thanks from faraway Russia!
Sir. I followed all steps you mentioned but still I am getting below error. A fatal error occurred: Failed to connect to ESP32: Timed out waiting for packet header
@Fiverearning220
2 жыл бұрын
Any solution
Absolutely amazing sir!! You have all the possibilities and errors. No other videos mentioned this! Thank you for making this wonderful video sir!! You earned new subscriber sir..
Thank you for the use of close up on the camera. So many video makers zoom out so you can not see anything. Thank you.
дякую!!!!!!!!! проект з поку врятований!!!!!!!!!!!!!
Thank you sir, but I got 0x105 error init. At first, I can acomplish until serial monitor gives me the IP address, but when I first access it, there just a blank black square. I reset it and then the serial monitor says "camera failed to capture" again and again. I unplug the whole thing, and then I try it again, now the serial monitor says "error 0x105 init" something like that
A fatal error occurred: Failed to connect to ESP32: No serial data received. I got this error..What might be the issue?
esse vídeo me ajudou muito a entender como conectar a camera, eu estava fazendo do jeito errado e com isso nenhum exemplo de codigo funcionava...
Appreciate the clear instructions. I however am unable to flash to the ESP32. All the wiring including the GPI 0 to ground was checked a number of times and i still get the message "A fatal error. Timed out for Packet header". also I note that the LED's Tx and Rx on the USB/UART connector do not flash at all. could something be wrong with the camera module GPI 0 pin. Appreaciate your help
@Joel.uno.uno_siete
2 жыл бұрын
have you solve it yet?
@Fiverearning220
2 жыл бұрын
Any solution
@juanemanuelsuarez8432
Жыл бұрын
@@Joel.uno.uno_siete no and you?
@jeniflorance6029
Жыл бұрын
me also facing same problem
Excellent video! Very clear and concise
I programmed the ESP 32 cam as you instructed, however, when i try to get still image, i get a jpg file which is empty. It is as if my ESP32 camera is not able to click a still image that is supported. Need help urgently please
Supper video. Nicely done
Dear Sir, After using this instruction I got this is error on web browser --> "Header fields are too long for server to interpret." Please Help.
Very nice, explained in detail. Very much helpful
I have error compilling for board AI Thinker ESP32-CAM ...what should I do?
Camera init failed with error 0x105 . How can I resolve it? However I have tried multiple times removing and connecting camera pins. Please guide.
Thanks a lot, You are a diamond. Finally I solved my problem
Can i run servo in esp32-cam? I tried it but it doesn't work. But with LED flashing and buzzer it works
sir i am still getting issue with eps32 wifi cam it always shows fatal error timeout please fix my problem
great explaination, keep up 👍🏻
Excellent sir. I bacame fan for you
if i saw loading up to 100% but failed to follow instructions of pulling the jumper wire and.pressing the reset. Do i need to hard reset/erase? or just do the procedure again?
Thank you very much, your video was very complete and helped a lot in my project!!
Hi ! If I don't have an arduino, can I make Cam ESP 32 settings? Is there an option for motion detection? If a thief enters my yard and steals my camera, can I see the recordings on my server / my cloud ?
Yesterday I have purchased and uploaded 2 times. Third time all connections correct and cause fatal error unable to resolve it all. I think cable or ft232rl or esp32 cam is gone.
Success! Thank you very much for your excellent teaching.
Thnak you! Very useful tutorial! Excellent video!
Can we upload the recording to sd card somehow? like it might be inconvenient to always provide wifi to the camera , might be if i use it on any project..thanks for explaining in such detail.
Thanks i have all this problems you talk now i solved . it's work
Definitelly best how to on eap32 cam. Thanks
exec: "cmd": executable file not found in %PATH% Error compiling for board ESP32 AI THinker I got this error when i try to compile the code, anyone can help me with this? i have downloaded the wrover library and has exctract into the /documents/arduino folder , btu i still face this issue. Please help , thank you in advance
@mayanksaini9524
2 жыл бұрын
Same with me
Sir I had tried your this project as per your tutorial in several times , everything is working but when select face recognition / face detection my face it is not shows any square on the face and not working, although I have change my cam module with AI thinker but still is not working. I would be really grateful if you give me the solution.
@echandu1167
2 жыл бұрын
havent you got the nts\Arduino\libraries\WiFi exit status 1 fd_forward.h: No such file or directory This report would have more information with "Show verbose output during compilation" option enabled in File -> Preferences.
doesn't the module gets really hot?? how can you manipulate it?
Thank you for you make a great instructor.
sir, I have tried it. Camera streaming is working, but I'm not getting any rectangle around my face. It seems like face detection is not working. Please help me with this
great video, thank you for sharing this stuff with us!
Very clear instructions, helped me a lot, thanks, subscribed.
Nice instructions, however it did not work for me after trying 100+ times. Plus now the original code is gone and esp32 does not come up as a WIFI on search, so the device is now useless with nowhere to go. Is there a solution where the device becomes just like new, i.e it can create its own wifi and atleast can work as a cam? please help
I am getting crc doesnt match error after downloading latest version of esp32 in board manager
I can upload the code and esp32 cam also shows the IP address of the web server but I am not able to open the web server on my browser. The browser page says 'connection time out'. Any solution for this error?
sir u have used external power source for esp32 cam then how u have down loaded code from laptop
i have error detected camera not supported but I selected good camera model and its isnt working. What can I do?
all code is complied but after pressing reset wifi is not connecting and we are not having ip address
Precise and Excellent
I am getting 'no programmers available ' And an error :fd_forward no file in directory What should I do....?
Can it be possible to have an sms notification when the esp detects an unenrolled face?
rst:0x1 (POWERON_RESET),boot:0x3 (DOWNLOAD_BOOT(UART0/UART1/SDIO_REI_REO_V2)) waiting for download how to remove this error?
@venkatesanc1801
2 жыл бұрын
Bro have you cleared this error pls help me I too got the same???.
@abstruse123
2 жыл бұрын
Remove the shorting jumper b/w GPIO0 & GND and then press the reset button
how to flesh this module or it's chip for reprogramming again
Can I connect esp32 cam to FPGA board using cp2102 without the use of arduino?
doesn’t work. It keeps on saying a fatal error occurred; Failed to connect to esp32: timed out waiting for packet header
would you happen to also have a solution for: "A fatal error occurred: MD5 of file does not match data in flash! " ?
I was unable to connect to the website while I was entering my IP address in the popup.
Can i remove and solder directly without 0ohm resistor because if i remove it i wont be able to solder it back my soldering skill is bad
Thanks very helpful
im facing problem with serial port not received, how to handle this error?
wonderful troubleshooting, thank you
This is not AI thinker so which board is this ?
Thank you sir for this amazing video!
Does this process needs to be done every time that I work with it?
Hi Sir. my serial print is "dl_matrix3du_alloc failed" when i turn on face detection and face recognition. may you help me please? i need your help
can anybody help me to select the port...coz it is showing grey and not selectable content in my laptop...I have also tried in my other PC too :(
Very clear❤❤❤
Sir it's showing brownout detector was triggered and not showing ip in serial monitor what should I do please help
Very useful. Thanks for the video.
Very nice tutorial! I wonder what's the amperage that goes to the ESP32.-CAM If I wanted to provide another power source would 5V 0,5A be sufficient?
@pascalguinet1940
Жыл бұрын
I did measure 250 mA, esp32-cam + cp2102 adapter.
can this board send the video over serial instead of wifi?
Learn new module, thank you Sir.
Thank you sir, very nice video,,
thank you sir its working welll
Very nice demo
@saurabhrajora1077
3 жыл бұрын
Nice
Great job, keep it up!
Thank you!
Sir we are facing with burnout error how xan we resolve it.
In ssid & password, can we put our mobile phone's hotspot name & password. Will that work ?
rst:0x1 (POWERON_RESET),boot:0x3 (DOWNLOAD_BOOT(UART0/UART1/SDIO_REI_REO_V2)) waiting for download ets Jul 29 2019 12:21:46 Sir do you now how to solve this error this is is coming after removing gpio 0 and gnd I am opened serial monitor and pressed reset button in esp32
Sir ji, link in description ? There are none. Please update. Thanks,
Sir, possible to make project call activation camera with this board
Helpful video
Amazing! Very clear
So you cannot use FTDI?
Great video! Thanks
After removing jumper and resetting. In serial monitor it's showing bunch of sign like question mark square arrows etc plss help
@muhammadharis8405
Жыл бұрын
Change the Baudrate
Code updloaded but serial monitor i am not getting correct output
Great video , thank you ❤️❤️❤️
Great video. I am using Arduino Uno to program esp32 cam. But getting the same repeated codes in the serial monitor, also I have powerd my cam with 5v supply. So what should be the problem sir ?
@Artificial.-_-.intelligence
3 жыл бұрын
kzread.info/dash/bejne/f3-dq7Z-o7LdgqQ.html
A fatal error occurred:Failed to connect to ESP32,no serial data received.
What is the baud rate