Episode 2 - Tools Every Apprentice Electrician Needs To Start Their Job

Тәжірибелік нұсқаулар және стиль

TOOLS USED IN THIS EPISODE LINKED BELOW!!
If you're about to start your career as an electrician but don't have a clue what tools you need, feel free to consult this list. In this video I talk about all of the tools that I deem necessary to start your career with. There will be endless tools that you will buy through the years but these are the basics that every apprentice electrician needs.
In order as they appear, I also time-stamped each tool so you can find them easier. If you'd like to buy them I've put links to each tool on Amazon below so you can order them if you'd prefer:
First up is to get a good pouch. You'll need a two-sided pouch with a hammer loop and a tape chain. One side of the bag should have storage for your hand tools, the other side should have multiple pouches for storing staples, screws, wirenuts, pens/pencils, markers, and a tape measure. You'll want a separate hammer loop (one thing I forgot to mention in the video...a hammer!) that hangs behind you from the belt. Its a lot easier to have a hammer hanging from behind you than off to the sides smacking into your legs all day. (0:56)
Klein 10" flat-head screw driver with a 3/8" tip. (1:12) - amzn.to/2TASZqe
Klein long-shaft 6-in-1 multitool (1:31) - amzn.to/2KrhPok
Stanley Sheetrock Saw (2:33) - amzn.to/2DPQBrf
Klein Lineman's Pliers (2:58) - amzn.to/2S78Nj0
Klein Side-cutting Pliers (3:30) - amzn.to/2KoODyl
Klein Small Wire-Strippers (4:12) - amzn.to/2DCpPSf
Klein Large Wire-Stripper/Crimper/Bolt-Cutter Combo Tool (4:38) - amzn.to/2BochIn
Klein Needle-Nose/Stripper Combo Tool (5:38) - amzn.to/2DQPEyU
Fluke T5-600 Multi-meter (6:23) - amzn.to/2DQPKXi
Klein #2 Square (Robertson) Driver (7:39) - amzn.to/2DSZ78Z
Klein ¼” - 9/16” Nut Drivers (more specifically 3/8”, 11/32”, 7/16”, and ½”) [your 6-in-1 will come with a ¼” and 5/16” so you don’t need to get these] (8:26) - amzn.to/2DRnofl
Klein Mini terminating screwdrivers (Philips and Flathead) (9:42) - amzn.to/2S3Mb31
Husky Utility Knife (10:01) - amzn.to/2QZBiiw
25’ Stanley FAT MAX tape measure (10:52) - amzn.to/2S72D2C
A pack of Sharpie Markers (12:13) - amzn.to/2S7GlgT
Non-Contact Voltage Tester (12:55) - amzn.to/2S8MZUo
¼” Masonry Bits (14:16) - amzn.to/2qXE6kV
Bosch ¼” to 1 ¼” Paddle/Spade Bits (14:11) - amzn.to/2qZzevO
¼” and 5/16” Drill Drivers (14:56) - amzn.to/2S74kgu
Drill extensions with Philips, flat, square, and torx tips (buy a whole kit of various tips separately) (15:10) - amzn.to/2Ktnb2I
GFI plug tester (15:40) - amzn.to/2DRoR5B
Headlamp (15:55) - amzn.to/2FyaFA7
1 1/8” Stepped Uni-Bit (16:34) - amzn.to/2S4DCVB
Klein Stubby 6-in-1 Multi-tool (17:24) -
amzn.to/2KpQino
18v Lithium-Ion Hammer Drill (you’ll need at least 2 good batteries and a charger) (18:26) - amzn.to/2KnFuWM
Small Lightweight Drill (Screw-Gun) (19:58) - amzn.to/2DRnuUn
Various Drill Bits (metal bits, wood bits, stone bits, spare drill extensions, drill bit index etc…) (20:47) - amzn.to/2Fyjb1W
Set of fitted gloves (not leather gardening gloves - fitted mechanic’s gloves) (21:32) - amzn.to/2S3GhyX
Several GOOD flashlights (check into Nebo) (23:02) - amzn.to/2S1mVKG
Multi-Allen Wrench Tool (23:55) - amzn.to/2DBoBXn
2 Sets of Medium-Sized Channel Locks (25:12) - amzn.to/2R13521
NOT TALKED ABOUT IN THIS VIDEO - 22oz Ewing Claw Hammer - amzn.to/2FC8fAk
That’s pretty much it for the needs of a fresh apprentice. If you have any questions please reach out to me at dustin@electricianu.com
If you like these episodes please SUBSCRIBE to the KZread Channel to be notified the moment each new episode comes out.
Website - www.electricianu.com
Instagram - / electrician_u
Facebook - / theelectricianu
FB Electrical Wizardry Group - / learning_content
Twitter - / electrician_u
#electricianclasses #electricaltraining #electriciantraining #apprenticeelectriciantools

Пікірлер: 1 300

  • @ElectricianU
    @ElectricianU6 жыл бұрын

    I made a significant error in this video. I said Greenlee was not a very good brand of tools but I meant to say Commercial Electric. (Both Green) - Greenlee makes outstanding tools, Commercial Electric's tools are shit. Sorry for the mistake, now I'll go kill myself lol

  • @charleshart5563

    @charleshart5563

    6 жыл бұрын

    Electrician U all good I think most understood where you were going

  • @topflight408

    @topflight408

    6 жыл бұрын

    Dude wasnt your plug tester Commercial Electric ??

  • @aaronsloan1523

    @aaronsloan1523

    6 жыл бұрын

    Thanks so much for the Greenlee clarification. I don’t use them normally but I have a backup set that’s Greenlee and have been very impressed.

  • @salg500

    @salg500

    5 жыл бұрын

    @@topflight408 there plug testers are about the only decent thing they make lol

  • @jjjr8664

    @jjjr8664

    5 жыл бұрын

    I use commercial electric on residential and Klein on bonded worthy sites.

  • @tonyrossi3151
    @tonyrossi31515 жыл бұрын

    I love when electricians makeup a reason to makea video about their basic carry. Can't we just be honest and say, "I LOVE MY JOB AND WANT TO SHOW YOU MY TOYS.. I MEAN TOOLS." I love talking to new guys in the trade about my knipex and Klien tools.

  • @ElectricianU

    @ElectricianU

    5 жыл бұрын

    You got me lol

  • @esl4058

    @esl4058

    3 жыл бұрын

    @@ElectricianU Don't be sad. I reguarly send pictures of new tools to other gearhead friends lol. It's all just legos for adults. Let's be honest haha.

  • @racc8050

    @racc8050

    3 жыл бұрын

    @@esl4058 yea

  • @rgbglass7163

    @rgbglass7163

    3 жыл бұрын

    @@esl4058 oh no is this my fate😭🤣 hey bro look at this new screwdriver I got💀

  • @NastySasquatch

    @NastySasquatch

    3 жыл бұрын

    Completely. as an industrial mechanic/engineer I carry all these tools plus...more toys. I love comparing tools with other tradespeople to find new toys.

  • @mitchw4876
    @mitchw48764 жыл бұрын

    I would also add these things to the list: - Torpedo Level - Tin Snips - Conduit Reamer

  • @JesterMereel

    @JesterMereel

    3 жыл бұрын

    Torpedo level was one of the tools he showed homie.

  • @christophernersesian2238

    @christophernersesian2238

    2 жыл бұрын

    Tools for "apprentices" electricians

  • @Cherbius

    @Cherbius

    2 жыл бұрын

    @@christophernersesian2238 idk about the tin snips but I don't see why not have a conduit reamer

  • @ChristiannTyler

    @ChristiannTyler

    9 ай бұрын

    @@Cherbiusmy snips get a work out but we set a lot of slider brackets helps keep your side cutters a little fresher but also we have the luxury of working near our big husky bags/boxes so space isn’t all that limited for extra crap.

  • @Goabnb94
    @Goabnb943 жыл бұрын

    The most important tools aren't things you'll buy in a store: 1) Punctuality - show up before your start time, and have breaks only at the allotted times, not dragging them out 2) Awareness - be aware of the big picture of things. If something doesn't look right, tell somebody. It might not be, or maybe its something to be taught to you. It shows you are actually thinking and not going through the motions 3) Be inquisitive - ask questions. Make sure you are thinking and understand the job you are doing 4) Take initiative - don't wait to be told what to do, just do it. Always be busy, even if thats cleaning up. And if there is nothing to do for a bit, look busy and the best way of doing that is looking at the plans. 5) Be eager to try new things - even if its typically an unpleasant job. By showing you are willing to do the tough stuff, you'll be trusted with the better stuff. I know this is strictly about physical tools, but an apprentice can turn up with just their basic toolbelt with a few essential hand tools. If they show the above qualities, it won't matter because their tradesman will have the tools they need for them to use. All the good ones at least, the ones who treat apprentices as students and not cheap labour, want a mind to be moulded, not a loaded person with all the fancy gadgetry who doesn't care.

  • @Roosyer

    @Roosyer

    3 жыл бұрын

    Excellent points!!

  • @martinsnibbor7691

    @martinsnibbor7691

    3 жыл бұрын

    I need one of those, all the kids now a days are spending their time taking selfie’s for Instagram.

  • @notsure7874

    @notsure7874

    3 жыл бұрын

    Excellent point for sure, but the guys that don't care don't generally show up with fancy gadgetry, they don't care. They show up with the bare minimum (or less) in all aspects. I see a guy that shows up with a 10 dollar pair of broken kleins, a rusty screwdriver, and a razor knife for ... like 6 months straight and either that guy is struggling to support his family and he's doing the best he can with what he's got - or more likely, he's just there to make beer money.

  • @maynefreeland8969

    @maynefreeland8969

    3 жыл бұрын

    I think an additional point would be to confidently say no. Been asked to do a lot of risky things, and no one pays anyone enough to not go home to the family.

  • @peter10195

    @peter10195

    2 жыл бұрын

    @@martinsnibbor7691 take me under your wing!

  • @LeftsnRights88
    @LeftsnRights886 жыл бұрын

    Nice video and I can relate. My Dad was a union electrician and I wanted to become one so I applied when I was 18 (1971) and took the test. I then had an opportunity to go to work as a non-union sheet metal worker shortly after High School and about 3 years later the contractor I was working for went union. About four years after I applied for electrician apprentice I got my letter from the IBEW Union Hall that I was accepted but I was already a Journeyman Sheet Metal Worker. I don't regret it because I learned how to install and service residential heating and cooling which saved me a ton of money. After 5 years of residential work, I changed to commercial and industrial.

  • @jessclark9725
    @jessclark97256 жыл бұрын

    Had a guy over me that always kept a dowel-handled wooden spoon in his belt. I never even questioned it, until I had to dig an ant hill out of a live meter pedestal years later. Idk if this is the sort of shit he used his for, or just a nonconductive probe, but ever since, I've kept one in my bag, for just in case.

  • @notsure7874

    @notsure7874

    3 жыл бұрын

    I keep one of those too. It's real purpose is to smack an apprentices hand when they're reaching for your tools! I don't really carry one, but that would be a great use for it.

  • @electricalron
    @electricalron6 жыл бұрын

    If you're a first year guy two things,.... 1) show up on time and 2) don't leave tools on the job because you'll be going back on your own time.

  • @felixarteaga667

    @felixarteaga667

    6 жыл бұрын

    and they most likely wont be there anymore XD

  • @steveramoso962

    @steveramoso962

    6 жыл бұрын

    i am with you! :'(

  • @jamesirwin19

    @jamesirwin19

    5 жыл бұрын

    This. So much this. 4 hour round trip tomorrow to get a 20V drill out of a store's electrical room. Dang it! 😂

  • @burtbiggum499

    @burtbiggum499

    4 жыл бұрын

    Make sure you track your gear throughout the day otherwise that shit grows legs

  • @themountofoliveschannelwit7009
    @themountofoliveschannelwit70095 жыл бұрын

    as an electrician for 27 years I agree 90% with you. Most of what you said is dead on perfect. In fact I carry many of the same exact tools that you do (exect I don't buy the ones with the comfort grip handles, I prefer the regular handles). . . . Things I tell an apprentice to have that you didn't mention would be a pipe cutter, wire snips(a.k.a electrician's scissors), crimpers, 3/8-9/16 ratcheting wrench, tin snips, a crescent wrench and a second measuring tape (because that is going to be you most often lost tool, keep a back up) .... I would also recommend a that a newbie to get a good hacksaw and Ratchet and socket set for switchgear, running cable tray and mounting equipment (nothing super fancy, just a good 3/8 set that covers the basics, I tell newbies not to buy mega expensive ratchet/Socket sets from Mac Tools or Snap On because we're not diesel mechanics, so Husky, Gearwrench and Craftsman sets work just fine in our line of work), but that is stuff that you will not need to carry around all the time......I also tell my helpers to get a 5 gallon bucket to carry their tools in (including their pouch). I always have a loaded pouch with me, but a rarely (almost never) wear it. Instead I prefer to wear a small mini pouch on my tool belt with just whatever tools I need for the job I am doing that for that day. I am not going to wear a loaded pouch full of stuff that I will not be using, hence the reason I carry my loaded pouch around with me in a 5 gallon bucket... Since I don't wear a loaded pouch all the time, I don't require my helpers too either. I get my helpers keep their pouch in a 5 gallon bucket (just like I do), that-away if you need more tools beside what's in your mini pouch, then you don't have to run all the back to the work van to get it. ....I would also recommend a carpenters nail pouch. When you are running conduit, you can keep one hole straps and screws in it, it makes it very easy and convenient (especially when your working up on ladders).

  • @themountofoliveschannelwit7009

    @themountofoliveschannelwit7009

    5 жыл бұрын

    Before someone rips over my comment about Expensive Mac Tools and Snap On ratchets and sockets...Let me point out again that Electricians aren't diesel mechanics. Although we do use ratchets and sockets, however it is not something we use everyday, sometimes we can go a month or even two months without using them at all. (((( So YES, I am very well aware that Snap On and Mac Tools ratchets and sockets are the very best that money can buy. ....In fact, a long time ago, I spent a lot of money on a Snap On tool truck buying stuff. Simply because I had the idea in my head that Snap On makes the best Ratchets and Sockets and I believed that I had to have the best. Only to realize that as an electrician I didn't use that stuff often enough to justify spending that much money on it when cheaper alternatives from Craftsman or GearWrench were available ...so when I tell newbies that they don't need Mac Tools or Snap On ratchets/socket sets... I still believe Snap On makes the very best Ratchets and Sockets, but since we aren't using them all day everyday, we (electricians) do not need the very best ratchets and sockets. Craftsman works just fine in the electrician world...... Yes I am actually speaking from experience.

  • @MrJahka

    @MrJahka

    Жыл бұрын

    Snips? What are you a commie or something?

  • @calebfink3542
    @calebfink35426 жыл бұрын

    word of advice: Avoid using a sharpie on things that will be exposed. it will usually show through any paint applied later

  • @andyfletcher3561

    @andyfletcher3561

    6 жыл бұрын

    I carry a 9mm mechanical pencil with HB leads. Can't erase markers. I've seen marker bleed through a layer of Killz.

  • @adamsifford4448

    @adamsifford4448

    6 жыл бұрын

    Sharpies are great for cutting and threading pipe to measure.

  • @malldollar4886

    @malldollar4886

    6 жыл бұрын

    So many people kill me with sharpie marks on pipe.

  • @selaxlife7621

    @selaxlife7621

    6 жыл бұрын

    Jacob Campbell lmao dude seriously!

  • @oscarmercado252

    @oscarmercado252

    5 жыл бұрын

    Not his prob

  • @yamasail
    @yamasail6 жыл бұрын

    On the subject of the carry belt, something I loved from the moment I started using it was a set of suspenders. Takes all the weight off your hips and back, reduces pain and fatigue, and keeps your belt from sliding down so it's always at the height you want without having to fasten your belt very tight at all. You can even adjust one side higher or lower than the other to compensate for the weight of pouches (I keep my right suspender slightly shorter since that's the side with most of my tool weight). Just make sure you get the good, wide work style with the thick metal clamps and teeth.

  • @ElectricianU

    @ElectricianU

    6 жыл бұрын

    I did that for a long time too, great advice

  • @ethanmanning938
    @ethanmanning9385 жыл бұрын

    I recommend getting tools with distinctly different colored handles that way you find the right one you’re looking for quicker and easier

  • @pbakai182

    @pbakai182

    5 жыл бұрын

    why not just tape the ends?

  • @steveburnett322

    @steveburnett322

    5 жыл бұрын

    A seasoned hand, knows where every tool is located in their bags and every tool has a place that lives in your belt, no need for color coding, grab and go!!

  • @Soldiershak

    @Soldiershak

    4 жыл бұрын

    I rather use tape, looking for different colors often times means it's a different tool or different properties. 95 percent of my tools are insulated so they're all orange and what not

  • @fallenkell

    @fallenkell

    3 жыл бұрын

    That is what electrical tape is for....

  • @notsure7874

    @notsure7874

    3 жыл бұрын

    I'm not a big fan of tape on my grips, and I generally reach and grab without looking. They're all different colors or very different visually in some way - but I operate my tool bag by braille most of the time. They all feel different, and they're always in the same spot. I don't lay shit down everywhere, it goes from my hand back to its slot. I've gotta put my hand there to grab whatever other tool anyway.

  • @trevorquick3953
    @trevorquick39533 жыл бұрын

    Hey man I am currently in school to become an electrician and I just want to give you a thanks. You've been a great supplemental resource and touch on a lot of things we don't get to in class. So, again man thanks.

  • @warriorguydudething
    @warriorguydudething6 жыл бұрын

    I'm a 19 year old, 2nd generation, 2nd year apprentice, and this video is spot on. I started out in commercial and then went to a high rise where I did decks, boxing, roughing the units, running a rough crew, and then down to parking garages and I have just about every tool I'll ever need but I still buy more just for the hell of it. Can never be too prepared

  • @user-hv1ik9li7f
    @user-hv1ik9li7f5 жыл бұрын

    Very clear that Electrician U loves being an electrician. Inspiring video bro.

  • @DustySteel
    @DustySteel5 жыл бұрын

    I really like your videos! I spent almost all night last night trying to figure out where I wanted this new year to go. I’ve always been interested in becoming an electrician because I want to someday build my own house and your videos have definitely helped me to decide on making it official and start the process on becoming an apprentice. I have a bunch of tools already but your video has helped me realize that I now have a reason to go buy some more.😁

  • @WolfieLovesDaddy
    @WolfieLovesDaddy5 жыл бұрын

    Thanks for showing how to understand electrical and prepare to do things right. I just subscribed so thank you again.

  • @uzielditter
    @uzielditter6 жыл бұрын

    A million of thanks !!!! Thank you for taking the time doing the video

  • @pjflores8499
    @pjflores84995 жыл бұрын

    Dude you even put the list in here. Thanks for this video, really helpful.

  • @justincarnes1553
    @justincarnes15535 жыл бұрын

    Pulling apart and reassembling the multi tool is super ASMR for some reason

  • @BradPwnsU
    @BradPwnsU6 жыл бұрын

    I would say you need, -a good 10in1 (multibit) screwdriver -a flathead for beating -a pair of sidecutters -Romex strippers -wire strippers -electrical tape -sharpie/pencil -phasing tape -keyhole saw -tic tester -ohm meter/tester I recommend Klein tools for the most part, stay away from Southwire or anything cheaply made

  • @IamPeacefulWarrior
    @IamPeacefulWarrior6 жыл бұрын

    You are a great guy, God bless and many thanks for the help. If everyone would share like you do, this Earth we live on would be a much better place ;-). Blessingssssssss...

  • @Lovinflyindrones2022
    @Lovinflyindrones20224 жыл бұрын

    I finally figured out how to wire a 3 way switch from watching your video on 3 ways. It’s kinda simple after u get it in your head. I thought at first u had power coming into both boxes but realized it only comes in on one switch.

  • @juliasrodriguez6437
    @juliasrodriguez64376 жыл бұрын

    Love the video, I’m looking to continue my training in electrical work and having a baseline for tools & gear is a plus. Thank you

  • @wanderingcalamity360
    @wanderingcalamity3604 жыл бұрын

    This is a great video. Thanks for this! I just applied for my apprentice license. Trying to get tools together, so this is incredibly helpful.

  • @davidweggel9573
    @davidweggel95736 жыл бұрын

    I would like to add a couple of items, tin snips, round and flat files , pipe reemer, hammer, hacks saw, WD40 DONE

  • @bam480v9

    @bam480v9

    4 жыл бұрын

    no hammer!

  • @affinity3281

    @affinity3281

    4 жыл бұрын

    I haven't seen anyone use a hacksaw in a good 8 years. It's as obsolete as a hand crank drill. Buy a used Recip saw if money is an issue.

  • @MusicConfusion99
    @MusicConfusion995 жыл бұрын

    Thank you so much for these videos, so glad I came across your channel. I'm 25, with little to no direction. I am willingly to work, and really excited I came across this. Being a electrician is something I can see myself doing. I am gonna bust my ass to become the best electrician. I can be. Going to be applying for apprenticeship programs soon. Thank you again.

  • @Dan67276

    @Dan67276

    5 жыл бұрын

    Good luck! Glad to see you going into a trade. Too much need for tradesmen and too many boys with no direction in this Country. Gotta' put the two together.

  • @Bilbus7

    @Bilbus7

    2 жыл бұрын

    Did you end up getting into an apprenticeship program? I'm also 25 thinking about getting into one.

  • @isaacloera2330

    @isaacloera2330

    Жыл бұрын

    I’m 24 & looking into getting into this trade! I would like to see your progress & any tips you may have!

  • @mulisha-kv7hn
    @mulisha-kv7hn5 жыл бұрын

    I just finished a 6 month class with the state of California for building and Electrical I had a blast can't wait to get into this field.

  • @vicentereyes200

    @vicentereyes200

    5 жыл бұрын

    where and what is the program or school called? I would appericate if you responded back!

  • @michaelfrost5868
    @michaelfrost58683 жыл бұрын

    Thank you very much. You’ve explained things that I have always wondered but never thought to ask.

  • @ebuyuto
    @ebuyuto6 жыл бұрын

    Thank you for showing this video. I have an Electrical Helper exam - written - this Saturday.

  • @nathanielgardener318
    @nathanielgardener3187 жыл бұрын

    If you are a first year but yourself a nice pair of knee pads and a good dustpan

  • @TakeItEasyGuy1994

    @TakeItEasyGuy1994

    6 жыл бұрын

    Nathaniel Gardener This is serious advice people.

  • @06maximaowner46

    @06maximaowner46

    6 жыл бұрын

    Yup, pretty much. I'm a fourth year, but I remember those days lol

  • @WARRIORlax1807

    @WARRIORlax1807

    6 жыл бұрын

    Knee pads and lipstick baby, that's all you need

  • @feboober

    @feboober

    6 жыл бұрын

    Also if you carry a lot of tools, a heavy duty belt. Or the trousers with pockets, at least saves your back. Knee pads are 100% a must. or one of those knee pads that have wheels on them so you can zip around on the floor.

  • @tylerweston3077

    @tylerweston3077

    6 жыл бұрын

    Nathaniel Gardener I can confirm this is true. I just bought knee pads today. That's funny. I'm doing a lot of wiring haha

  • @wb5mgr
    @wb5mgr6 жыл бұрын

    One really valuable tool I keep in my carry bag is a set of 3/8 Drive hex keys and torx keys metric and sae up to around 1/2" and a ratchet. Also a small assortment of 3/8" SAE/Metric sockets. Also a set of ratcheting wrenches.

  • @antonkeene6415
    @antonkeene64155 жыл бұрын

    Right now, I’m seeking to become an electrician by taking basic electrical classes in my local area, plus I like the aspect of going back to school, and I have grandparents who were apart of IBEW when they were creating fuses. It’s never to late.

  • @brenton4752
    @brenton47526 жыл бұрын

    Thanks for the info. I was a apprentice back in 2010 but got out of it and currently trying to get back into it again and go for my journeyman’s and then the masters.

  • @surfboylaney

    @surfboylaney

    5 жыл бұрын

    by now you should be in it to win it. I hope have good mentors etc. Always take that knowledge and add it to your own you'll be ahead of the curve.

  • @couldntthinkofagoodnamesoi8357
    @couldntthinkofagoodnamesoi83574 жыл бұрын

    Save yourself a lot of money: make a pilot hole for your step bits.

  • @ThomasKBurke
    @ThomasKBurke4 жыл бұрын

    I appreciate the guidance on this. I’m starting trade school Monday and I know at some point soon I’m going to need all this if I wanna start working somewhere as an electrician’s trainee soon. This is one of the better guides and rundowns I’ve been able to find, again much appreciated. Subscribed.

  • @wizard3z868

    @wizard3z868

    4 жыл бұрын

    great set like $10 at xmass but perfect durable as hell and lifetime warranty used em like crazy abused em never failed yet www.homedepot.com/p/Husky-High-Leverage-Long-Nose-Pliers-Set-3-Piece-1006/205913115?modalType=drawer

  • @everythingbobbywolfe
    @everythingbobbywolfe3 жыл бұрын

    The rapi-driv flat head is my go to for covers. Super light to carry. Keep the Philips for the receps and switches and the flat head for covers. Everyone that sees me use it, inevitably goes out and gets one. Home owners, too.

  • @cargenshepard8970
    @cargenshepard89706 жыл бұрын

    I'm a second year apprentice in the field I've found a slotted screwdriver is incredibly useful

  • @JesterMereel

    @JesterMereel

    3 жыл бұрын

    Yeah he mentioned that.

  • @bugzie27
    @bugzie275 жыл бұрын

    Thanks for taking the time to make this video , You rock !!!

  • @jimb2758

    @jimb2758

    5 жыл бұрын

    No kidding!!! Not only the video but all the documentation in the "show more." Your detail is second to none, thank you. I'm looking for a crimping tool to connect grounding wires deep in the box. My linesman's pliers have a crimp capacity, however, it's 6 or so inches from the tip. I would like to have something that I can crimp deep in the box. Thanks for all your hard work to make these productions. -jim b

  • @Funk446
    @Funk4465 жыл бұрын

    Baby channel locks were a gamechanger for my tool bag set up, the little 6" ones

  • @user-ey2wd7vq3z
    @user-ey2wd7vq3z6 жыл бұрын

    Thank you so much man, I just recently got the opportunity to become a apprentice and your videos have been nothing but super helpful and informative.

  • @ElectricianU

    @ElectricianU

    6 жыл бұрын

    Great news! Congrats my friend!

  • @o-zone2767
    @o-zone27676 жыл бұрын

    Nice video, a few things that i'd add to that is a good magnet for finding metal studs for fixing shit to once the dry wall/ceiling goes on, a hack saw, conduit cutters, a cold chisel and a hammer. Also i dunno if you guys use U clips in the US but having a template to draw the cut out for U clips with a level build into it is heaps useful and also some pencils

  • @strangerofthe2067
    @strangerofthe20674 жыл бұрын

    I’m currently around five years or so as a residential journeyman in Washington state, and while I do absolutely agree that Klein makes the best tools for electrical, I personally still buy and use commercial electrical tools for certain things, and it’s because I beat the shit out of some of them. I have certain tools that I’ll ONLY buy Klein, but I also have tools that I will also buy a second, cheaper brand of because I go through them fairly frequently. Also, in 2020, Milwaukee has started to make a lot more electrical tools that I personally really like. I make a pretty damn good amount of money so I can easily afford to spend more money on brands like Klein, but new apprentices might not have the same budget to start out with a tool bag full of Klein tools, and they also might decide this trade isn’t for them, so maybe if you’re new to the trade, make sure you’re fully committed to it before you go buying all the top of the line brands. One more thing- get that tape chain caught on a ladder while climbing up and down a couple times and you’ll rip that thing right off of your bags, hopefully before you get caught and lose your balance and fall off your ladder. I personally HATE those things and just see it as a hazard, but that’s just my opinion. Anyway, thanks for the video though, I really enjoy watching your videos and really like your channel! These kinds of videos were great for me early on in my apprenticeship, and all these years later I still really enjoy just hearing and seeing how others do it and their opinions and experiences in the trade. Thanks for sharing!

  • @matteusptasznik7826
    @matteusptasznik78263 жыл бұрын

    3rd Term apprentice with the IBEW here. For union apprentices theres a list of tools which you are required to provide for yourself. Everything else required for the job must be provided by your employer. Current tool list as written by the IBEW includes: - Linemen's pliers - Diagonal cutting pliers - Channelocks - #6, #8, and #10 Robertson screwdrivers - 5/16" and 1/4 inch flat head screwdrivers - #2 phillips screwdriver - measuring tape - tool louch and belt - safety hat - safety boots - log book (provided by JAC) - note pad - pencils - electriciams knife Im not going to get into what I would recommend having, this is just what the union requires you to have as an apprentice.

  • @FemboyAhri
    @FemboyAhri Жыл бұрын

    Hello Mr Electrician U! I had my instructor play your video to show the whole class. Glad you’re here to explain in great details.

  • @hardrock1826
    @hardrock18266 жыл бұрын

    When I started my apprenticeship many many years ago and I got out on the work site, the one tool I got told I needed was what was called a Yankee Screw Driver. So I got one, really excellent quality, actually made in Germany with a variety of Slot bits, Robertson and Phillips and it proved to be really handy, all these years gone by I still have it and use it periodically.

  • @ElectricianU

    @ElectricianU

    6 жыл бұрын

    Hardrock I've seen those but have never owned one. They look like they're from the 50s lol. I'll check into it, I'm curious now.

  • @Dreaded88

    @Dreaded88

    6 жыл бұрын

    @Hardrock: I still have my Yankee Screwdriver!

  • @Dreaded88

    @Dreaded88

    6 жыл бұрын

    @Electrician U: This is a Yankee Screwdriver, and this is how you use it: kzread.info/dash/bejne/iIaa0auyqJuxlrg.html

  • @andyfletcher3561

    @andyfletcher3561

    6 жыл бұрын

    We used them a lot before cordless was a thing. I had two sizes.

  • @askalexandratarot

    @askalexandratarot

    6 жыл бұрын

    My journeyman just gave me his old one!

  • @bigdadynickable
    @bigdadynickable7 жыл бұрын

    Hey I need some help in the field on how to read a blueprint when you're on a job site can you go into depth when you make a video And do a video on all the different conduit bending . Thank you.

  • @ElectricianU

    @ElectricianU

    7 жыл бұрын

    Absolutely!

  • @betomendoza5981

    @betomendoza5981

    7 жыл бұрын

    nick barrows look for the garage, it easiest thing to spot

  • @wb5mgr
    @wb5mgr6 жыл бұрын

    Last thing I would suggest, have a labeling device. Tape is great for marking phases, but for more detailed stuff I like having a book of wire numbers or letters to mark stuff. Self laminating write on labels are great as well.

  • @mark52111
    @mark521113 жыл бұрын

    Excellent video! Thank you for sharing your craft and promoting your trade. We need more folks like you in the trades. Keep up the great work.

  • @jpizzel9629
    @jpizzel96296 жыл бұрын

    Could you make a video and talk about being a union electrician vs non union electrician and what the pros and cons are of each. What about apprenticing for the union or non union? Please answer man I'm on the verge of making a radical change from going to college to being an apprentice because I don't feel like I truly learn anything when I don't have shit to apply it to in real life. Love your videos man!

  • @Blank00o001

    @Blank00o001

    6 жыл бұрын

    JPIZZEL hey I'm a union electrician if you'd like to talk I'd be more than willing. The main difference is money. 37.50 an hour plus benefits. Around 58$ and hour.

  • @nathanielgardener318

    @nathanielgardener318

    6 жыл бұрын

    Do you want to work or work for a living. If you like doing shit work for no money go be a rat.

  • @chickenby

    @chickenby

    6 жыл бұрын

    and the real union guys come out!

  • @Blank00o001

    @Blank00o001

    6 жыл бұрын

    Yeah bud. I work all day. I'm worth my money. That's the difference. Oh and btw next time you're rate job thank us for that.

  • @chickenby

    @chickenby

    6 жыл бұрын

    I'm sure you bust ass ron, i think anyone would for your pay

  • @lordrichard8184
    @lordrichard81845 жыл бұрын

    I’d add a mirror and fish tape to the extra tool bag. I was in a situation where my fish tape wasn’t feeding up through a wall like it should have. So I used my mirror to see inside the wall and find I was getting bound up on a box that I didn’t know was there. And I could adjust accordingly. Also it might be a bit of a hassle at first. But get flash lights and head lamps that use the same battery type. Either AAA or AA. This way you don’t have to carry around multiple types of batteries. You can buy a 20 pack of one and when you see you’re getting low you can buy a new one and know you’re covered and not worry about having to keep track of lots of batteries

  • @burtbiggum499

    @burtbiggum499

    4 жыл бұрын

    I use my phone in selfie mode and use that but a mirror would be quicker

  • @lordrichard8184

    @lordrichard8184

    4 жыл бұрын

    Brian Wilson yeah. But sometimes you need to stick the mirror in a place where you’d be really pissed if you dropped your phone. Both are great to use

  • @SparkyNJ
    @SparkyNJ3 жыл бұрын

    Just found your channel and love it so far! Love your tool list too. Can't say how many helpers I have had over the years that kept coming and asking to borrow something cause they didn't have it. Only nit-pick I have on your list was at the end. And that is a pair of baby channel locks. I get smirks from guy when they see them on my pouch. But, they are great for a lot.

  • @stefankeeney8462
    @stefankeeney84624 жыл бұрын

    In my past experience getting a holster for the impact gun especially one with a clip is so convenient. I like that i can keep it strapped to me without falling out if I’m in a persons home or a crawl space where I don’t want it falling out. Also I use the smaller pouches that will just hold my Essentials, and that would go on the same belt as the screw gun holster. Unfortunately I haven’t found a brand that makes the two so I get the husky pouch, and some off brand holster

  • @raulgil7389
    @raulgil73896 жыл бұрын

    Hey Dustin that is a very good method of sharing your knowledge and I think that besides being an electrician you should also be an E instructor thank you very much Mr. Dustin. Two thumbs up for you

  • @philippejoseph1215
    @philippejoseph12156 жыл бұрын

    you dont need half of this, if you are in your first year. Keep it light, you gonna be the one carrying ladders and all the equipements around. Don't spend a thousand before starting to work, add stuff gradually. -Good impact driver + charger + 2 batteries, red square bit - red square screwdriver - green square screwdriver - filledup screwdriver - flathead screwdriver - good cutter - good pliers - Cheap long nose - precision screwdriver flat and fillup - Knife - sheetrock knife - small level -Sharpies and pencils + pencil sharpener - 3m mask P100 cartridge I use to carry my hammer drill, but i prefer using the wired SDS from the compagnie, and leave my batterie drill in the car or at home If you do a lot of emt, charm your journeyman into buying a bandsaw, if he doesnt own one. That made my weeks go so much better :) It's just my opinion, i started a few months ago, and dont ever missed anything really, your journeyman gonna allready have a lot

  • @christophernersesian2238

    @christophernersesian2238

    2 жыл бұрын

    100% cant agree with you more on the bandsaw comment. I was 3 months deep starting my apprentice program. My boss used dewalt, i prefered milwaukee. Found out milwaukee makes a badass bandsaw powered by 18 volts battery. I bought one for $260.....wow was my boss impressed from it..way better and quicker for cutting 2" emt or older metal casted MCs conduit than any sawzall or hackzall.......my boss immediately bought one for himself the next day but made by dewalt. Mine was still more powerful.

  • @8dh73k0
    @8dh73k03 жыл бұрын

    I'm going into this field and I really appreciate the video. Thank you.

  • @LevitheScrapDaddy15
    @LevitheScrapDaddy153 жыл бұрын

    All of these videos are very helpful. And the straight forward and positive attitude helps the learning process.

  • @YakMotley
    @YakMotley4 жыл бұрын

    Wow! Great video! I was taking notes and im not an electrician lol!

  • @jordytorresvlogs2713
    @jordytorresvlogs27136 жыл бұрын

    Hey man love your vids. Im only 16 and i want to learn the trade good video im worling with my dad right now hes an electrician as well. Love the vids

  • @BowmanHawk
    @BowmanHawk5 жыл бұрын

    Klein has a beauty precision multi driver. Like the 6 in 1. Calling it a square screwdriver was priceless. Like a homeowner calling it a star screwdiver.

  • @robyoung9463
    @robyoung94636 жыл бұрын

    Also Awl, center punch, chisel, & small hammer, Chalk Line (which can be used as Plumbs your Bob), Cable cutter (for heavy gauge wire), make sure your level is Magnetic, Blue ele Tape, set of Stubby Drivers, Hole Punches, adjustable wrench, EMT Benders, Fishes, i find a Chalk Bag really handy for PARTS & a Rope, a circuit tracer & jumper wires to tap into junctions, Safety Gear (huge list) its kind of Job Specific : )

  • @erikstenquist177
    @erikstenquist1773 жыл бұрын

    Are’s we not going to talk about the awesome impression of cutting a live wire 😂😂😂😂

  • @jdmoores28
    @jdmoores286 жыл бұрын

    Great video sir. I'm just getting into the trade, the amount of tools needed can be a little overwhelming on times. I'm starting to slowly put together a decent amount of good tools

  • @JasonRobinsonidaho

    @JasonRobinsonidaho

    6 жыл бұрын

    neighbor just went through diesel mechanics school. those guys have $2k in tools just to start!

  • @jakehart7617

    @jakehart7617

    5 жыл бұрын

    Manabozo and a good hammer

  • @ivansierra950
    @ivansierra950 Жыл бұрын

    great video, helped alot just graduated from eletrican school and ready to get started in the trade. got most of these tools, job interview today. lets go go out be safe and have some fun :)

  • @Drewpost19
    @Drewpost195 жыл бұрын

    Awesome vid. I’ve done electrical part time for a couple years and wish I would’ve saw this. Thanks

  • @pascalblanke470
    @pascalblanke4706 жыл бұрын

    Its really interesting to see how different you work compared to electicians in Germany.

  • @WCamden

    @WCamden

    5 жыл бұрын

    And in uk lol

  • @andrewvigil9469

    @andrewvigil9469

    5 жыл бұрын

    How so?

  • @gersonpilotzi7503

    @gersonpilotzi7503

    4 жыл бұрын

    How many hours a week do they work?

  • @trentdokis9988

    @trentdokis9988

    4 жыл бұрын

    African 1st Congolese 2nd 40 plus overtime actually

  • @wifilost

    @wifilost

    4 жыл бұрын

    @African 1st Congolese 2nd lol I put in 70 hours a week and I'm a electrician apprentice.

  • @tootall5559
    @tootall55596 жыл бұрын

    One thing to remember, the better tools you buy, the more likely they are to walk off with somebody else. One job had some really sticky fingered bleeps, I lost 6 lineman's pliers on that job, not to mention the many other things that walked off. You didn't go to lunch and leave your tool bag around. Once the stuff was stolen from my car on that job.

  • @MintStiles

    @MintStiles

    5 жыл бұрын

    You'll definitely be safe with the Ryobi neon green ;)

  • @pooki3slinger832

    @pooki3slinger832

    5 жыл бұрын

    So true dude. Now that's why I never leave my stuff unattended ever again.

  • @tonysoprano9370

    @tonysoprano9370

    5 жыл бұрын

    Look after your tools then. When you go for breaks pad lock your box

  • @KitchenerLeslie2

    @KitchenerLeslie2

    5 жыл бұрын

    I guess that’s one good thing about being a residential electrician. Only a few crews on a site at most. 15 years I’ve never even heard of tools being stolen.

  • @anthonychirillo539

    @anthonychirillo539

    5 жыл бұрын

    6 pairs? That's your fault now, bro. You're leaving your shit unattended or just not paying attention.

  • @InspiredCraftsman
    @InspiredCraftsman2 жыл бұрын

    I've had great luck with temo cobalt step bits. For headlamps I've been using the armytek wizard pro, run it all day on a charge. It also unclips from the headband and has a magnet to clip to metal. Thanks for the content!

  • @I1IWEBB1
    @I1IWEBB14 жыл бұрын

    Thanks for taking your time to educate people like myself on this. Great information

  • @bakerboy8910
    @bakerboy89105 жыл бұрын

    My list of what I carry as a first year: Klein ratcheting cutters Husky 12-in-1 screwdriver Wiss cable cutters Komelon mag tape, 25' Milwaukee 7/16 driver Eklind folding Allen Homemade hawkbill knife Kapro magnetic handy level 3m 76 tape DeWalt chicken stick Crescent brand crescent wrench Southwire compact strippers 1 1/2" cold chisel Uline permanent marker Craftsman magnetic angled head flashlight w/ clip

  • @joed9988

    @joed9988

    5 жыл бұрын

    wtf is a chicken stick?

  • @JoseDiaz-mb9lj

    @JoseDiaz-mb9lj

    5 жыл бұрын

    I carry Milwaukee drill and impact Torpedo level Tape measure 25ft Rabbit Ears 7-1 nut driver 11-1 screwdriver Needle nose Ratchet with all size sockets Voltage tester Flashlight Pipe wrench Pipe reamer Ratchet cutter Side cutters Lineman Terminating screwdriver set Wire strippers

  • @guitarguync
    @guitarguync6 жыл бұрын

    Those one-handed sawzalls are really useful too, should be your 2nd power tool after a drill.

  • @BULLTRONHERO

    @BULLTRONHERO

    3 жыл бұрын

    I think you mean one-hand bandsaws

  • @guitarguync

    @guitarguync

    3 жыл бұрын

    @@BULLTRONHERO Bandsaws are great, but you can do more with a sawzall. Personally, I'd get a sawzall first.

  • @BULLTRONHERO

    @BULLTRONHERO

    3 жыл бұрын

    @@guitarguync You most certainly can do a lot, but it's far easier to not mangle unholy fuck out of your EMT and large cables (250+) and 3/0 etc. with the bandsaw.

  • @BULLTRONHERO

    @BULLTRONHERO

    3 жыл бұрын

    @@guitarguync I guess I should also specify that I'm in Commercial

  • @zebmccollum
    @zebmccollum6 жыл бұрын

    To save space, and have more tools, I’d recommend getting Klein’s 6-in-1 multi bit nut driver, their 4-in-1 electronic screwdriver, and their 15-in-1 multi tool.

  • @nickm9102
    @nickm91023 жыл бұрын

    I work in IT in the field. About half of the tools listed are what I would put on my list. My big thing is that I use metric and not ASE. I have also been looking for a decent magnetic screwdriver since I have the chance to encounter a variety of screw caps. Thankfully 60% of what I do is with a PZ1/PZ2 driver but that other 40% is nut drivers, wrenches, various power/network testing tools, pliers, a laptop, and a drill. but I have been trying to make a balance between having a good catch all kit to carry in and leaving stuff in the van.

  • @Zamb_
    @Zamb_5 жыл бұрын

    Klein tools are exchangeable at Home Depot, no questions asked so when I blow mine up I can just get new ones for free

  • @albanysigep

    @albanysigep

    5 жыл бұрын

    klein doesn't replace "blown up pliers"

  • @Zamb_

    @Zamb_

    5 жыл бұрын

    michael gaffney how? I’ve taken my lines men’s and strippers to Home Depot, both with holes in them, and the replaced them

  • @DARKWOLF-td1lw

    @DARKWOLF-td1lw

    4 жыл бұрын

    Zamb_ pro tip, buy used Klein tools off Craigslist or other sites for cheap and return them to Home Depot for new tools :D

  • @ronsbeerreviewstools4361
    @ronsbeerreviewstools43617 жыл бұрын

    A good video, it would of been nice if these type videos were around when i started my electrical apprenticeship ----- then again there were no PC or internet then. ha ha 😎

  • @ElectricianU

    @ElectricianU

    7 жыл бұрын

    Rons beers lol I was thinking the same. There's not a lot of content around for guys to go to when learning a lot of shit in this trade. I'm hoping to cover some of that gap wih my channels - hopefully more guys will join and make free content for all of us to benefit.

  • @AngelRomero955
    @AngelRomero9552 жыл бұрын

    Just landed my first apprenticeship! It took a lot of preparation to get there but I’m ready !

  • @totalannihilation9065
    @totalannihilation90655 жыл бұрын

    I do most of my electrical work myself. I got most of those tools if not all including better quality voltmeters. The most money I had spent has been on the voltmeters and 200 dollar bags and pouches. It's good to have tools.

  • @blakehorton8110
    @blakehorton81105 жыл бұрын

    Been in it for years just mho but I like to go with an small pouch that holds my basic hand tool ie. lineman , 10 in 1 , stripper , diagonal , / the rest I keep in an bag that's organized , it may not seem like it but big bags even with shoulder straps can pinch nerves and cause problems with your back and the like over the years 👍

  • @joet.plumber3771
    @joet.plumber37716 жыл бұрын

    They’re called Robertson bits. Nice vid young man.

  • @willie7845

    @willie7845

    4 жыл бұрын

    Yes, thank you.

  • @MyUnquenchableThirst

    @MyUnquenchableThirst

    4 жыл бұрын

    both words can be used. like Flat Head or you can say Slotted.

  • @Roosyer

    @Roosyer

    4 жыл бұрын

    young man?? what tha

  • @lassaut6794

    @lassaut6794

    3 жыл бұрын

    Actually, the term "flat head" comes from "flat head screws" that have a flat head and taper towards the "auger" postion of the screw that allow the head to be flush to the work surface like wood screws, as opposed to machine screws that portrude from the suflrface being fastened, which back in the day were exclusively slotted. The correct term is flat blade screw driver.

  • @niketurban.5569
    @niketurban.55696 жыл бұрын

    Thanks for your thoughts on this, I am currently thinking about becoming an apprentice and Ill take that advice to heart.

  • @gustavoguidor156
    @gustavoguidor1563 жыл бұрын

    Great video and full of very good advice. Man, you don't know how much you're helping those who are entering the trade! Great stuff you have! I'm from Costa Rica, and in my country it's very difficult to find good tool brands, like Knipex, Channnelock or Klein, and if you are able to import them somehow, they price grows twice, due to absurdly high taxes. I'm looking to get one Klein tool pouch, like yours, but I'll have to save more money. And wait a couple of weeks.

  • @ziprock
    @ziprock6 жыл бұрын

    having a tape that has measurements on the bottom can be handy when working overhead too

  • @ElectricianU

    @ElectricianU

    6 жыл бұрын

    That's a great idea actually. I've not seen many of those in Home Depot or the local supply houses so I just never think about it it but you're right...great idea!

  • @benjamintheis7670
    @benjamintheis76704 жыл бұрын

    Love the channel! What is the brand of that black pouch? I’ve been looking for something similar and haven’t had any luck

  • @Hitchross

    @Hitchross

    3 жыл бұрын

    I’d like to know this too! It looks exactly like what I’m looking for

  • @MarcosMartinez-vd2iv

    @MarcosMartinez-vd2iv

    2 жыл бұрын

    Klein Tools 5167 11-Pocket Tool Pouch. I have the same one

  • @TOBMESTER
    @TOBMESTER5 жыл бұрын

    Iman apprentice in Norway and we get all the tools we need by the company we work for, got the same tester as you have, probably used it a hundred times the first month

  • @johngarcia5269
    @johngarcia52695 жыл бұрын

    I feel a major tool I use everyday is the klien reamer also acts as a nut driver. Vital tool when bending pipe, i feel as it’s the most used tool in my pouch.

  • @crimsonmoon9213
    @crimsonmoon92136 жыл бұрын

    9:04 this dude gotta live in Texas. I know the sound of that bird in the background

  • @thenotjam1

    @thenotjam1

    5 жыл бұрын

    SoCal same lmao

  • @bschilt3

    @bschilt3

    5 жыл бұрын

    That's a Eurasian Collared dove

  • @jamesipad204
    @jamesipad2047 жыл бұрын

    Should make a video of the power tools you'll need. Getting a portable band saw made me enjoy being an electrician

  • @ElectricianU

    @ElectricianU

    7 жыл бұрын

    James iPad man I really want to make one badly! I've got so many damn videos I want to do on more advanced stuff too. I'm going to do that but I'm trying to start these slow and from the very beginning so they can be watched by green Apprentices from day 1 and then start ramping it up as we go

  • @JulesBartow

    @JulesBartow

    6 жыл бұрын

    12V Milwaukee bandsaw kit for cutting flex, MC, Kindorf, unistrut, EMT, liquid-tight, rigid, and bolts is best $160 I ever spent.

  • @jamesipad204

    @jamesipad204

    6 жыл бұрын

    Jules Bartow the dewalt has speed control, very handy for cutting armour cable without hitting the wires inside

  • @JulesBartow

    @JulesBartow

    6 жыл бұрын

    Yep. Barely circle your way around PVC, AC, MC, ... Milwaukee is variable speed too. 12V is light weight & capable.

  • @darthcollosus

    @darthcollosus

    6 жыл бұрын

    Fuck that you shouldn’t have to buy any power tools your employer should provide you all that shit and if they don’t you work for a shit company

  • @AnonMemSoc
    @AnonMemSoc5 жыл бұрын

    Thanks for educating these youngsters

  • @brandonhughes882
    @brandonhughes8826 жыл бұрын

    Great vid, wish I would have watched this video before I started as an apprentice about a year and a half ago... I made the mistake of buying the milwaukee drill/impact combo set, which I like a lot, but at the time I didn't know they made the drills with a hammer drill feature otherwise I would have gotten one of those instead! Also, right off the bat as a first year I found myself using PVC cutters a lot, very handy. A couple other tools to add would be a decent claw hammer and sledge hammer. Depending on what company you work for you may not use those all too often, the first company I worked for did a lot of new construction and underground work so I was always driving emt stakes and cutting/gluing pipe. With my new company I haven't touched those at all yet lol.

  • @timmcpherson6708
    @timmcpherson67085 жыл бұрын

    Industrial all the way man I've never done residential or commercial going on my 3rd yr of apprenticeship

  • @mathiusfigueroa3899

    @mathiusfigueroa3899

    4 жыл бұрын

    How much you get pay per hour?

  • @timmcpherson6708

    @timmcpherson6708

    4 жыл бұрын

    $17.20hr with free insurance and $5.50hr more going to retirement

  • @timmcpherson6708

    @timmcpherson6708

    4 жыл бұрын

    I think the whole package for a third year is close to $30 an hour

  • @mathiusfigueroa3899

    @mathiusfigueroa3899

    4 жыл бұрын

    Tim Mcpherson are you in the union ?

  • @timmcpherson6708

    @timmcpherson6708

    4 жыл бұрын

    Yes I am

  • @stevejobsmichel6253
    @stevejobsmichel62536 жыл бұрын

    NICE TOOLS BRO

  • @arnieselectric007
    @arnieselectric0074 жыл бұрын

    For your Klein extended shaft 6 in 1 screwdriver, replacement tips are Phillips 32400, slotted 32401, and #2 sq with #2 Phillips is 32410...Just found them...

  • @andywolf6312
    @andywolf63123 жыл бұрын

    This is an awesome vid. Pretty awesome channel altogether. I am a General for residential remodel and I try to get the 411 from the trade pros. Today, amongst other things, I learned about the strippers with the screw cutters. So many times I have had to cut screws for covers on a backsplash. Yee-haw!! Also did not know about the long shaft 6 in 1's Good Stuff!!

  • @paulgus9252
    @paulgus92526 жыл бұрын

    U forgot about wire stretcher. 😉

  • @rotam8680

    @rotam8680

    6 жыл бұрын

    AC battery

  • @wirenutnut4458

    @wirenutnut4458

    6 жыл бұрын

    The wire stretcher thing is funny, I’ll admit, but some guys just keep that type nonsense going and going way too long. Usually it is the semi advanced helpers or almost electricians that keep Wild goose chase stuff going. For you new guys, just laugh it off and move on. Do not waste your time with looking for sky hooks, liquid wire, wire stretchers, 4/0 wire nuts, black phase tape, ac batteries, etc... Tell the person that is asking you to get that stuff to stop trying to hinder your progress with useless games. Say teach me something about real electrical work. You will find that most of the time the ones teasing you all the time, don’t really know much about anything. That’s why they mess with you all the time. They don’t want you to advance. What I am trying to say is, find a good electrician that knows how to have fun at work but will actually teach you something useful at the same time.

  • @Brian-se4hs

    @Brian-se4hs

    6 жыл бұрын

    All that stuff is so ridiculous, man they finally got me with a 3 piece a 3 piece emt couplinge

  • @brentmorris262

    @brentmorris262

    5 жыл бұрын

    @@wirenutnut4458 And yet, we had one maintenance guy looking around the plant for two days, trying to find the wire stretcher. If you fall for it once, shame on me. If you fall for it for 2 days, shame on you.

  • @salg500

    @salg500

    5 жыл бұрын

    What about a left handed bender? :p

  • @mandybabel468
    @mandybabel4685 жыл бұрын

    I'm about to graduate from a trades school in the summer. Going into my apprenticeship soon after, being a female residential electrician and knowing there aren't many of us, any pointers ? Been told all kinds of things but wanted to know from someone with experience. I work for Lowe's, so I'm good on tools. 😁

  • @jasonmarroking4357

    @jasonmarroking4357

    5 жыл бұрын

    Mandy Babel Lmfaoo I work at Lowe’s so I’m good with tools 😂😂😂This is the funniest Shxt I have seen today !!

  • @michaell4527

    @michaell4527

    5 жыл бұрын

    Not too sure what's funny bout working at Lowes

  • @miavaughn2393

    @miavaughn2393

    5 жыл бұрын

    @@jasonmarroking4357 Not good with tools, good on tools asshole. She probably has an employee discount so was speaking to that effect.

  • @selaxlife7621

    @selaxlife7621

    5 жыл бұрын

    I wish u would try to energize my panel....

  • @mrdoe7283

    @mrdoe7283

    5 жыл бұрын

    Try not to emphasize so much on being a female and just focus on being a safe electrician and learning something new everyday day. Food for thought, good luck.

  • @g0dmach1ne91
    @g0dmach1ne915 жыл бұрын

    I'm glad I found these videos. I've just started studying Electricity/Instrumentation/Control Technology at our local community college, so that I could find a decent paying job out in the middle of nowhere where I live (and also because I imagine this type of work will be available anywhere in the country should I want to move). I'm still just in the opening weeks, learning the very basics. One of our assignments is to look up tool sets for electricians and make a list with prices and whatnot of all the pieces. I had already done that, so I was glad to see that pretty much everything I had already listed was mentioned here. I do have a question tho - there seems to be some cases of people hating on Channellocks and preferring 'water pump pliers'. They look the same to me, except maybe water pump pliers look more insulated or something. Is there really any big difference there?

  • @ericarae7464
    @ericarae74645 жыл бұрын

    Very helpful! Thanks for the great knowledge! I just started my apprenticeship last week so definitely needed this!

  • @c-zen890

    @c-zen890

    4 жыл бұрын

    You still in the trades? How far along are you now?

  • @jenniferperez2966

    @jenniferperez2966

    4 жыл бұрын

    Update please.

  • @son0flaw366
    @son0flaw3665 жыл бұрын

    This is awesome but you didn't mention anything about the wire stretcher? Boss is always telling me to go find it.

  • @ElectricianU

    @ElectricianU

    5 жыл бұрын

    Hahahahahaha holy shit that one got me.

  • @wwsxa39

    @wwsxa39

    5 жыл бұрын

    Can purchase them on Amazon. Not much use for a sparky though. www.amazon.com/RanchEx-102569-Wire-Stretcher-Standard/dp/B01KJOJIU4/ref=sr_1_1?crid=1FRSBYTZFQTAW&keywords=wire+stretcher&qid=1558876553

  • @matthewj616
    @matthewj6165 жыл бұрын

    We call those testers “hot sticks” or “idiot sticks”

  • @slyspy9819

    @slyspy9819

    4 жыл бұрын

    That's the most important tool you'll own as a Electrician how can you say that ? Detecting voltage is a must before you can move on any call you get . Every tool has a purpose and knowing when where and how to use them is the difference

  • @MyUnquenchableThirst

    @MyUnquenchableThirst

    4 жыл бұрын

    @@slyspy9819 I don't think he meant to type Tester. I think is was referring to the Ticker or Sniffer

  • @slyspy9819

    @slyspy9819

    4 жыл бұрын

    @@MyUnquenchableThirst Sounded like it to me , if he had the "Greenlee 2010 he wouldn't say that

  • @wanderingcalamity360

    @wanderingcalamity360

    4 жыл бұрын

    @@slyspy9819 I think you're missing the point of the name. It's not an insult to the tool. It for detecting if the component is hot so you don't make an idiot out of yourself.

  • @slyspy9819

    @slyspy9819

    4 жыл бұрын

    @@wanderingcalamity360 , What do you mean "make an idiot out of yourself" ?

  • @PixelOverload
    @PixelOverload3 жыл бұрын

    For tape measure, I recently got a hold of an inverted lock design (it always stays out when you pull it until you push a button to retract) which should have always been the standard as far as I'm concerned. It's some "Home Handyman" brand I never heard of but it's a solid, thick tape with a heavy duty rubberized shell that just feels great to use

  • @Hans0622
    @Hans06225 жыл бұрын

    Roto Split, Tin Snips, Hole Saws, and maybe a reciprocating saw.

Келесі