That oil seal pulling pry bar is quite the multi tool

@40ChannelCruiser

Жыл бұрын

Yes, the pry bar is a great tool!

Clear information great video!

@40ChannelCruiser

Жыл бұрын

Thank you

Mate, really good and informative video - great work 👍

Excellent video, planning to do this on my 72 FJ40. I am glad that I found your site.

@bobdelano6746

2 ай бұрын

1970 fj 40 here

Great job - very well done. One point, when setting bearing preload, you can hold off on putting the cone washers in till you get it where you want it, then put the cones in and assemble properly. This way if you need to add/subtract shims from top and bottom, you don't have to screw around with the cones. Be sure to double check preload once the cones are in.

Excellent, thorough detail. You made it look easy. Thank you.

Restoring a ‘76 FJ40. Your videos are the best.

@40ChannelCruiser

2 жыл бұрын

Thanks mate! Feel free to share photos of your build. Have a fantastic Christmas! 4045channel@gmail.com

Mate, you're a legend. You go through the steps and that's such a tremendous bonus. Thank you

How about that shout out!!! Thanks brother, appreciate it!

@40ChannelCruiser

4 жыл бұрын

You're always welcome mate, sharing the love😋

@bigfellasydney6970

4 жыл бұрын

Project wrong way.. another awesome channel!

Best results using swivel hub centering gauge tool now available as aftermarket special service tool. Metal to metal surfaces do not seal . Any metal cased seals should be installed to oil grease free metal housings with a sealing compound for interference fits. (Not rubbish silicone sealer) This includes wheel bearing hub seals . Oil from grease leaks out . Metal to metal does not seal also usually gouges from screwdrivers etc during seal removal , metal cased seals can't seal the gap , oil leakage path. Swivel hub studs can be removed ( double nut them ) from housing and studs washed oil grease free install studs with thread locker , it will seal and stop the greases oil from dripping out . Dummy fit trunnion bearings and use centre gauge to check hub centered on axle housing and check preload , make any adjustments for correct centre and preload , when correct dismantle and clean shims , swivel hub shim surface and trunnion surface apply Loctite master gasket to shims , swivel hub , trunnion mating surfaces by doing this greases oil will not leak out of metal to metal surfaces . It's the little bit extra on the job that makes a massive difference to longevity of a repair or overhaul. Inner axle shaft Seals need to be installed to oil free housing with retaining compound or gear oil leaks in . Cv shaft must be centred in housing , great care must be used when installing axle shaft into inner axle shaft seal or it will be damaged from the Start . Bit of a ordinary design the inner axle shaft seal anyhow . Vent axle housing and transmissions to atmosphere using extended breather hoses up to high in engine bay , internal pressure from stuck breathers causes forceful leaks. Long live the 40 .

Thanks for the video and the valuable information too ✌

I dont have an oil seal puller but found that a medium side shifter had about the right arc angle to do the same job. Super simple.

Thanks for the great video

Wonderful info...super helpful. Keep up the great work. Going to use your comments on rebuilding the front end on my 78 fj40. Thx again.

cheers mate great video, found your comment whilst searching for a kit for my 1992 ln106. I'm now ready to take it head on!

Superb! This project is coming soon for me so your timing is impeccable. I'm headed to amazon to get a luggage scale.

*Great Video!!*

@40ChannelCruiser

4 жыл бұрын

Thanks for your support mate.

Great video man thanks for the video I did it to my hj45 is fun to work on Toyota’s lc thanks I always see your videos great again this cars are expensive to restore but well worsted sheer

Thank’s for making these videos, very helpful.👍

Your the legend

Super cool work on the video perspective! Gotta love the camera tripod! Thanks

@40ChannelCruiser

Жыл бұрын

Thanks James.

Great video buddy!

@40ChannelCruiser

4 жыл бұрын

Thanks mate, I appreciative your support!

I can't believe you have 7/11's there, awesome. I hate dealing with the shims, pulling them in and out and checking to get the weight right

Great Video, Man. Very in depth and helpful. So glad you are doing this!

Howdy from Virginia! Bought my first FJ 40 today. A 1977 that needs tons of work. Thanks for all the great videos. I know they’ll come in handy when I start my project.

@40ChannelCruiser

4 жыл бұрын

Congraulations Mate! welcome to the 40 series Family. Mine is also a 1977 so I hope that mine channel helps you throughout your build!

@mpr3209

4 жыл бұрын

@@40ChannelCruiser Thanks, Brother. If you ever make it to the USA beers are on me. :) FYI--these guys are about 40 minutes away from me here in Virginia. Good guys with lots of Land Cruiser know how if you ever have a question. Some good videos on their site: www.otramm.com

This is outstanding news. You not only have 711s down unda, you know the value of the SLURPEE. 40s and Slurpees are a solid combo

@40ChannelCruiser

4 жыл бұрын

My kids are the big Fans of the Slurpee's and if I'm buying them on then I had better get one too!😉

Thanks

Great video, but I'm wondering about the knuckle preload. The workshop manual for my BJ46 recommends 1,8-3,8 kg. Not 3-6 kg as mentioned in the video. That is far too much in my opinion. Another observation is that the the gasket next to the dust cover is on the outside of the cover, not on the inside between the dust shield and the knuckle spindle.

cheers mate I'm about to do the same stuff to my 1970 FJ 45 ive got the front diff out only took 3days lol never done anything like this before never had a 4x4 Toyota this one is a night mare and I don't have half the tool,sor money as I'm older much older than the ute andam a pentioner.But I,ll get it done some how thanks for your tips

@40ChannelCruiser

4 жыл бұрын

Great to hear that your going to get it done no matter what, Never to old to learn new tricks! Good on ya Doug

oh the old fordeen mill...

First comment and first like. glad you found that bad bearing. I used a trunnion bearing eliminator on that Blue 75 I built just for that reason. Those bearings don't like bigger tires

@40ChannelCruiser

4 жыл бұрын

You are quick of the mark mate, Yes when I brought the FJ40 it was on 33" But as you know I have gone with the original rims. I like the look of them better for this project.

Hi 40 channel, im pretty sure your meant to pack the felt seal with grease as well otherwise it acts as a sponge and holds water.

when you finished this one I reserve you a plane ticket for France I have my BJ42 which needs a good renov

@40ChannelCruiser

2 жыл бұрын

Lock it in mate!

@richardgrognard6394

2 жыл бұрын

@@40ChannelCruiser he is already locked up

Really like the video. Just had a quick question with setting the preload on the knuckle. If it's either too tight or too loose and you have to remove or add shims, do you find that it is always best to do it on the bottom? Or should you try to do it at the top as well?

what's that chassis sprayed with looks mighty fine! would love to hear what you've used!

question, did you use moly grease? I thought that would be the wrong type for wheel bearings.

You forgot to install the last baring mate

👏🙏🌹

@40ChannelCruiser

Жыл бұрын

Thank you.

What did you do at 24:26 to get the axle past that point. I’m fighting mine at the same spot. Thanks!

Can I ask what you did to finally get the axle to go in to the diff centre? That bit was cut out and mine are being a pain in the butt after doing the knuckle rebuild. Thanks mate.

Where whould i find the luggage scale you used?

Where i can get this knuckle steering housing for FJ40

Living the dream the top cone in it will not go down more than a half the distance it needs to go down this just a little over finger tight at that point you can not move the knuckle i have check the bearing is down in the race way and looks like it is sitting up as far as yours is any help would be great .

@40ChannelCruiser

2 жыл бұрын

Feel free to send me a photo. 4045channel@gmail.com

Great video again Jayson! Man you know a lot about these rebuilds. Have you done them before?

@40ChannelCruiser

4 жыл бұрын

Thanks Dave, This is the first 40 series Landcruiser I have done, But not the Last! I have built a number of thing in the past. There is lots of great info on the Book of Face forums and IH8MUD, that has been a great info guide.

Why did you not changed the brass bushings? Did you measured them? Good video despite of that. 🙂

@40ChannelCruiser

4 жыл бұрын

Thanks Matt, I did buy two new brass bushes but the ones in the hub looked good, no damage or scoring at all. So I left them in.

Hey. Absolutely love the channel. Got a question. Where about do you get all your gaskets from??

@40ChannelCruiser

3 жыл бұрын

Hi mate, from onlineautoparts.com.au

struggling get that CV joint back in as you were. Any tips? What were you facing and how did you overcome it? Seems to be bottoming out somewhere.

@40ChannelCruiser

3 жыл бұрын

Hi Steven, I ended up Turning the center of the diff a bit and tapped the end with a dead blow hammer and just popped straight in.

@SDALWeller

3 жыл бұрын

@@40ChannelCruiser Got it, thanks mate. I ended up juggling it a bit and turning diff slightly and it worked. appreciate it and all the great details you've provided. Cheers!

Hey really good video! I want to do this to my fj40 from 1979, can you share where to buy this kit from the internet?

@40ChannelCruiser

3 жыл бұрын

HI Juan, yes you can buy the kit from onlineautoparts.com.au

what brand are those ratcheting spanners

@40ChannelCruiser

3 жыл бұрын

G'day Mate the brand is called 'King Tony' www.toolking.com.au/search.php?search_query=King%20Tony%20spanners%20ratchet&page=1§ion=product

Vid only shows you removing shims from the bottom - should remove equal top and bottom to keep the axle centred?

@boxmat182ify

4 жыл бұрын

I was thinking the same thing. I'm about to attempt this and I'm gonna get the little scale. But I would have thought remove them equally from top and bottom.

@scod3908

4 жыл бұрын

boxmat182ify, make sure you get a mechanical scale and not a digital one.

@boxmat182ify

4 жыл бұрын

Yeah I can do that, how come though?? What's your reasoning?? Thanks!

@scod3908

4 жыл бұрын

boxmat182ify, a mechanical one is easy to read when the measurement isn’t constant. The digital ones jump around a bit due to the averaging etc. Think of standing on a mechanical scale vs an electronic one - mechanical is instant but electronic takes a second or two to show the value.

Mate where did you get your knuckle kit from?

@40ChannelCruiser

3 жыл бұрын

Hi Wayne, brought from onlineautoparts.com.au

Hello and good morning, I'm having 1984 Bj 41. My bjs hand break light is not functioning. There is no wire connecting the hand break with bulb if possible plz share the pic or guide me with what to do. Thanks

@40ChannelCruiser

2 жыл бұрын

Send me an email, I try and help 4045channel@gmail.com

@duldul5038

2 жыл бұрын

@@40ChannelCruiser hi, waiting for your email

@40ChannelCruiser

2 жыл бұрын

@@duldul5038 sorry mate, I haven't received an email. Maybe try again. 4045channel@gmail.com

Complete novice here! How come you knew to remove the bottom shims and not the top shims?

@40ChannelCruiser

2 жыл бұрын

Hi Will, there is a OEM tool that you can use to find the center and can adjust the shims to suit. But if you don't own the tool I set it up so there is about the same shim thickness top and bottom, so in this case there was more on the bottom which is why I removed them. Hope this makes sense.

Hey! You skipped how you got the axle in! I’m out in my shop doing the same thing right now watching specifically for that moment! Mine is stuck in the same spot. Did you just keep wiggling and pushing? Thanks...

@estein63

4 жыл бұрын

Never mind! Struggle with that dang thing for 30 minutes. Walked away and came back 15 minutes later after I calmed down. Went right in. I have no idea what I did different. Sometimes these things are so frustrating! Anyway it’s party time now. 🎉🎉

@40ChannelCruiser

4 жыл бұрын

@@estein63 🤣 Yep same thing, I was fighting it and was getting a bit frustrated so turn off the camera and then in just popped in🤨 The other side went in very easy but didn't film that side. That's the way it seems to go!

@ToyotaLandCruiser

4 жыл бұрын

Maybe it would help to turn a pinion flange just a bit that the splines match...?

@40ChannelCruiser

4 жыл бұрын

@@ToyotaLandCruiser Don't worry I was trying that too! (Off camera)

@estein63

4 жыл бұрын

40 Channel yep, me too. Then all of a sudden it just slid in....wish I knew. Still have the other side to go!