Engraving METAL with the Ortur Laser Master!
Get your Ortur Laser Master 3 engraver here (Use code ZX50 for $50 off!): s.zbanx.com/r/pgssTv232OHv
Or through Amazon: www.amazon.com/Master-Engrave...
The Ortur Laser Master 3 is a 10w diode laser that can cut and engrave all sorts of materials!
Support me on Patreon: / natefromtheinternet
Join me on Instagram: / nate_from_the_internet
Пікірлер: 178
My friend's business uses a small 20W CO2 for engraving. The warning sticker on the front reads "DO NOT LOOK INTO LASER WITH REMAINING EYE" and, for convenience, it's also in Braille.
Maker's Muse posted 2 videos about these kind of laser cutters/engravers not that long ago. He talked about what you need to look out for when engraving different matterials and also some concerns about the safety of them. I would highly recommend you watch them to be on the save side. And Nate did a great job building an enclosure for it.
@salmon85
Жыл бұрын
meh youtube deleted my old comment, comgrow make enclosures that you can buy (mainly for their own cutters / engravers, but imo as long as it's bigger than the frame of your machine, it should fit)
@conorstewart2214
Жыл бұрын
Yeah such a great job on the enclosure, large gaps for the laser to escape.
@marcus_w0
Жыл бұрын
@@conorstewart2214 It overlaps. There's no way it escapes, because it's light, not a liquid. Those gaps are for venting out the smoke.
@conorstewart2214
Жыл бұрын
@@marcus_w0 it absolutely can escape. Light can go at an angle you know, especially with reflections.
Thank you for highlighting the safety aspects too many creators gloss over or ignore safety precautions especially with lasers and resin
You are correct, bamboo just always does that. Even with a CO2 laser, that's the results. Also, a CO2 wavelength keeps it from marking bare metal. The best thing to use for metal is a fiber laser. Another way to clean the soot off of wood is with denatured alcohol. If it's a large piece, sometimes, we clean it first then hit is with a little sanding. Look into photos. A diode laser is slow, but it gives extrememly good results with photo engraving!
@oliverwjones
Жыл бұрын
I used to spray stainless with a thin coating of dry molybdenum lube spray and then engrave with a 40W CO2 laser. The laser would bond the spray to the steel and give the look of engraved steel.
@malonecustomdesigns
Жыл бұрын
@@oliverwjones Yes! We have a marking spray that we use sometimes like that! We made a video about marking/engraving on metal! :)
@jimeash7041
Жыл бұрын
@@oliverwjones The sprays made for laser engraving do a better job than moly I did a test piece of aluminum that I mask and use both products on the same letting, moly has a dark gray color and is almost smooth, the specific spray was black and you can feel it with your finger nail, our classroom machine is a Boss LS 1630 60 watt new this year, I'm the machine tool TA for the CAD/CAM Program so I have been working on a speeds and feeds materials spreadsheet
@oliverwjones
Жыл бұрын
@@jimeash7041 And the laser marking sprays are about $80/can vs $10 for dry moly...
building an enclosure is always a smart first step with these open gantry machines. I agree with other commenters that it's probably a good idea to get a better set of goggles certified for the wavelength. Interesting to see how well it did on the stainless without surface coatings.
@NFTI
Жыл бұрын
Ya I was too! No cearmark or anything!
@YourAflacGal
Жыл бұрын
My thought is... WHY no coating?
In our experience (with co2 laser engraver ) they emphasize using a ventilation system because the laser creates particles that are so fine they are inhalable . we deal with plastic so I am not sure if that makes a difference, but I suggest finishing your exhaust system sooner rather than later. Great video!
@TheBntimmins
Жыл бұрын
My job laser engraves labels onto plastic. We have the enclosure hooked up to central vac. Because of the fine particles.
Finally! someone who addresses the glaring safety issues of these lasers. I'd have gotten one already except for my fear of having a 5W+ laser sitting around my house.
@AdamMclardy
Жыл бұрын
An enclosure is so easy
@billymacktexasdetective5827
5 ай бұрын
I bet you are afraid of your own shadow as well...
Congrats on the new toy! I just got the xTool D1 (almost the same machine, functionally), and I've been using it to make leather armor! Super awesome!
I love lasers but I also don't wanna loose my eyesight. Those laser goggles don't look very convincing, I would side with StyroPyro and suggest getting laser glasses from a reputable brand specifically for the wavelength of your laser. Remember kids: safety first and never skimp on PPE
Nate - spend some money on some goggles certified to block the wavelength that laser diode emits. Your vision is worth more than some cheap amber goggles.
"I got a new tool. The first thing I'm going to do is build a box/enclosure for it." -Pretty much every maker Great video.
Love watching you testing this out! Can't wait to see what you make with! A possible upgrade to the enclosure would be an interior switch that kills the laser if the lid is open (more for safety of others who might see or be around and don't know all about it) Not sure if the new laser has a way of adding that, but could probably add an input to computer running lightburn, or just make it kill power to the laser. Idk, if you decide to add one, I'm sure you'll come up with something even more clever than above.
Electrical tape is made of PVC, when you ablate PVC with a laser, it will create chlorine gas, so electrical tape isn't the best option. I highly doubt that little amount is anything to worry about, but just a comment for the future :-)
glad to see everyone here referencing makers muse's video
For another, in-depth perspective on this type of machine, I recommend the video from Maker’s Muse: kzread.info/dash/bejne/X22cq7qNaKezhbg.html Short summary: If it doesn’t have an enclosure with proper venting and shielding, you’re going to be breathing fumes from whatever you’re cutting (probably a health hazard), and could incur eye damage from a laser reflection or even set the room on fire.
I friggin love that you're building again
That looks freaking awesome Nate, great laser, need a chain on the lid of the box to hold for you 👍🏼👍🏼🇦🇺🇦🇺🦘🦘Cheers from Melbourne Australia
Laser some lunch meat lol. Just as a quick sanitized look into what would happen if a hand went in, kinda like waterjet channel did with hotdogs
Angus at @makersmuse would be proud of your safety precautions!
i think co2 lasers cant cut metal because its infrared light, and metal is pretty damn good at reflecting that. thinking about a rescue blanket here, that stuff gets vapor deposited metal on it wich is ridiculously thin, yet perfectly able to reflect most of the IR radiation from a person
Instead of making a Masonite blank, and tracing your metal off of that, now, you can make your blank, check its feel, and then put the metal in and run the exact same pattern, and you've already got your trace.
Nate got me wanting something I never would have thought I wanted 😆
Some metals work, some metals don't. I have made attempts at metal and it just comes right off by shop towel. Copper/brass/aluminum don't work well because heat goes away to quickly. Air assist, is more used for the cutting side over engraving, but can still be used. For the bamboo color variations, its does the same for different types of wood, even same type of wood but different tree. The settings you have set for the engrave side can actually be turned up- faster speed/higher power to get faster results. Lightburn is the preferred program by many laser users. In lightburn there is a material test that you can figure out the best setting for each material. Darkest spot, fastest speed, lowest power- usually gives best results. The box you made for it, I would have recommended putting the white side towards the laser. Dark colors are easier to engrave/damage.
Love the Ortur products but for knife engraving you should definitely go the Fiber laser route. Way faster and basically it is made for it.
Nate, just an idea... I've seen your passion for knife making and if you had a knife making business I'd buy one from you and I'm sure you could make a ton of money doing something you love.
@malonecustomdesigns
Жыл бұрын
He does have a website where he sells them. Look up Haukr Knives
@F_L_U_X
Жыл бұрын
@@malonecustomdesigns OH awesome! Ty
@malonecustomdesigns
Жыл бұрын
@@F_L_U_X You're welcome. You can find a link in the description of some of his knife videos...I just don't want to post the link....links usually gets blocked from comments.
Amazing I love it. 😎👍 Do my Umbrella Corp. Logo next, please. 🙏
That seems like a lot less cost than I thought it would be. $800 for the higher end model.
Can it fake a Damascus pattern? How does it do cutting clear acrylic, or other clear plastic?
Hey nice vid. I was ordering a muffler and they were going to laser engrave it for me with my logo. I was wanting a more bronze look instead of very black like what yours did. Is this dependent on the source material I provide or the machine and the way they do it? Was wondering if I need to provide them a brown color logo vs my standard black one or does it matter?
How is this going to change how you do the iron man suit?
Is that amber acrylic designed to block certain frequencies of light or is it just amber?
wow very cool
How does it do with aluminum? Maybe in a future video? Thank you.
That's bad ass.
Dont use lazer engravers without A) very good ventilation B) the proper lazer saftey eyewear (no, the cheap pairs sent with most lazers are _not_ good enough)
Maybe a silly question, but couldn't you etch an outline of your knife design on a block of metal?
@sunburstworx
Жыл бұрын
He could, but if he is going to do 5 or more of the same blade shape, it would be faster to trace from his template. Also, the cutout he did is great for prototyping to see if he likes the feel of the shape.
@andromydous
Жыл бұрын
@@sunburstworx True. I wasn't thinking about Nate making multiples of the same design.
I have seen from ILTMS Bob that if you place a layer of blue painters tape, it will stop the shadow engraving getting rid of the need to sand it away
Do you think that laser could do a makers mark. ( if you had the patience to do something like that.)
If I sent you a design that I have been told cannot be cut and like to see how that would cut it out in the metal does it do metal as far as cutting out is concerned. What’s the depth?
Nate - where did you get the range Plexiglass panels you used on the enclosure?
Awesome! Another thing my wife will tell me no to.
@DonovanHaumpy
Жыл бұрын
Noted, never get married 😆😂
Does the software come with the laser? I'm new to this. Thanks!!
Great, a new video! Thx.
7:33 little overkill for a business card :)
Hello Nate, great video.... I need some help I'm a bigginer and I can't connect to the (laser explorer app) to my ortur laser master 3. Any suggestions? And I'd also like to know when selecting the kinda material to use how many material database dose the app has? Appart from wood
For personal use the diode is good for metal but for mass production the fiber is 👌🏽 but the cost is wayyy up there. Great video.
You’re not supposed to use manufactured woods with laser cutters. The glues are made of chemicals like formaldehyde that get vaporized into the air.
lmao can see in the reflection of the 'amber plastic' that you're not wearing the safety goggles half the time while its running.
I know this is an old video but I was wondering what Stainless you used and was it hardened and tempered? Thanks
is there a way that you can measure the depth of burn on the knife? i would be curious to know two passes go how deep?
How about heat and smock it not be a problem with this box you made ?
Laser company: This thing has two layers of protection! Nate: Have you met me? I'm gunna build a whole nother layer. You're amazingly capable and terrifyingly clumsy. A fun combination from a safe distance!
A honeycomb bed helps when cutting.
Cool capability. I would try using technique of burning not only the logo but the actual knife template straight to the steel. Clear permanent precise lines? The wood template good for test/fine tuning the shape but...Put the template straight to the metal instead of wood template traced to metal?
@malonecustomdesigns
Жыл бұрын
Sure....although he can't cut it out with the diode laser, he could us the diode to basically score a cutting guide into the metal.
Can you use this to make a faux Damascus knife?
You should try making a hammer
why wood and not metal for the panels?
*In our next video, StyroPyro stops by to upgrade our laser engraver with a diode that's 100 times more powerful.*
I'm looking for a laser engraver to engrave 24inch X 24inch stainless steel. What do you recommend?
Nice video Nate. If you like lasers, you might enjoy a few of our videos! :)
Lightburn is nice once you figured it out
How does this one comparison to the Genmitsu Jinsoku LC-40 Laser Engraver you reviewed not too long ago
ok ask for only steel since he stated that is 3x more time than he can do. oh no my handle doesnt 'feel' good. what if I have no idea how my hand feels :( so if I order the knife type without a handle; do I get more than a 30% discount or?
i struggled getting anything like that, im using 24w diode and done your settings as different settings and nothing as like that
You literally vaporise the material and you can adjust the spacing and angle of attack to get a prismatic effect.
Well now I just have to bite the bullet and order one of these, I've been hand engraving/etching my co workers and my own butcher knives over at work for like 15 years now. Want something to have higher detail as the intricate things I do are getting to be VERY annoying..... Thank you for the review.
Hi! Are those speeds in mm/minute? Because mm/meter makes no sense to me
I'd love to see if it can etch into 925 or 999 silver!
That is likely the 10watt version. They have a 20 watt one now that will engrave stainless steel in hundreds of colours believe it or not. It is all done by setting the power levels and the differing amount of heat gives differing colours on stainless steel. I can’t wait to try it when mine arrives.
@billymacktexasdetective5827
5 ай бұрын
That's not engraving. It's marking. Huge difference.
I know you did the stainless. What about a blade of 1095 or O1 tool steel? Try the annealed and one after being heat-treated. Those are the alloys that most of the knife makers i know use and have some difficulty marking. I know a true (deep) etch will require a fiber laser. Just curious as to what affect it will have on these materials.
I'd like to etch or engrave pure silver. Can this machine handle that?
Hey man cool video. I’m a blade maker my self , I have a bunch of knives of finished with handles, how will this laser go putting a logo on a finished knife? Meaning the blade will no longer lay flat… will I need to prop the knife up to make it level some how or will it work out its own level… or etch it anyway?
@jhen6612
5 ай бұрын
It is best to prop it up and make it level so you can set the distance of the laser.
can you adjust height with this one ? Say if i have a product, a box, a mug, does it still get the job done on the unflat surface?
@jhen6612
5 ай бұрын
You can adjust the height of the laser itself but if you need to do something taller, you can raise it with legs that Ortur sells. A method I used was tuna cans since they are a uniform size and they are stackable to get the height you need. Ortur also sells a roller and a rotary chuck for cups, mugs and other round things.
Any chance your on line ? I'm trying to engrave tumbler with ortur and I've gone through 8 cups. Ant chance I can ask u some questions?
Question, it works on wood, plastic, I am assuming metal but does it work on glass? And what is the depth?
@jhen6612
5 ай бұрын
Yes, it does work on glass. Not sure about the depth.
I can to engraving in Silver or gold with this láser, thanks You.
Hello, we bought "ortur master 3", we completed the installation, but when we start the machine, the yellow light flashes and gives a signal. The computer does not recognize what should we do?
I would love to know if it could cut through half inch cardboard and do an awesome design in the cardboard?
@jhen6612
5 ай бұрын
Yes it will. You would want to have it raised so the laser can escape at the bottom. Its best to run a test for speed and power to avoid setting it on fire.
Is this on Amazon. If not. Please let the company know to bring it on amazon
I would love to see if this laser engraver/cutter could cut and leave an image in leather??
@kiethomastephen2206
Жыл бұрын
It will engage leather, I was in a engineering design class they have these laser engraving machine, on the first day the teacher did a test run to show how it’s works and ask if anyone wants to engrave there’s phone, I ask if it could engraved leather wallet and it does.
I would like to see testing with cutting through various thicknesses of materials. What is realistic.
Remember to wear a respirator when using it. Ya don't want the vaporized material getting into your lungs.
What type of laser is this?
Stick some blue painters tape on wood surface before engraving.
Does it or can it work with a mobile app. Take pictures photos and send it directly to the machine. Instead of being behind a computer. Editoring. Just doing my work while pooping instead of stoping on the pc software to use the bathroom. Like the laserpecker app. Does it have a app for this. Mobile editing engraving is best. U don't be stuck in one spot whole day. Move around your house. Set up machine and be u. If any problems with machine. It will show up on your phone. U can head back to fix it. Thats what I would like
How many passes did you set for the "Dog Tags"?
@NFTI
2 ай бұрын
Maybe 3?
Cool laser, but does it also blacken chicken?
That is not engraving. That is marking a steel. Engraving does involve depth cutting, at least >17 microns. Has the manufacturer tested depth it can cut in few materials, wood, polymers and metals?
Can do direct to metal designs instead of cutting out a template nice
Could someone please post me a photo of the USB that fits into the laser. I need to find a replacement
*I'M A' FIRIN' MAH LAZER!!*
You have got to try cutting fruit with that...
without that air pump soot will get on the lens and fry them!
custom leather knife sheeths
I thought this was a video on how to set up and use the tool
also when you come to it please purify the air that's blown away, and having smoke and possibly toxic gases in the air is not fun. and like what Azrael said watch the videos by maker's muse, but good job for making an enclosure!
Glass
Price??
Hey Nate, you've got me wanting one of these! I make knives too, mostly with good old-fashioned forging. Want to trade blades?
Try a fake Damascus pattern on a blank...