i hope i can build this someday. it looks great!

몇년이 지나 다시 봐도 이 작품이 최고다!👍

God bless you brother 👍

Great work..whooaa ill do this then i will let u know ..thanks a lot sensei

May I know what tool did you use to but the ms brake set plastic material?

Very helpfull tutorial, thanks a lot , waiting for another tutorial (with english sub pls) 👍

@tonypapagna6027

4 жыл бұрын

How can I send you a picture or video ~? I want you see what I did~ and correct me if I’m wrong~!

The front roller have to use 19mm? Can I change to double roller 12-13mm?

can i know the item number use for roller attachments , the one attached wtih super x plate

Hi sir can u please kindly help advice what is the part number for HG carbob front wide stay you are using ? Thank you sir

@AZARASHI3ODN

5 жыл бұрын

It is Item No: 15498.

@Te-CaHobby

5 жыл бұрын

@@AZARASHI3ODN thanks you sir :)

what is the frp you use for that , ? thnk you sensei

Hi can u tell me what of part for use brake system at front?

@AZARASHI3ODN

5 жыл бұрын

Combination of carbon rear stay and carbon multi wide stay.

where can I get the rubber ring. item number please. also the eyelet, flatbed screw. thank you.

@AZARASHI3ODN

5 жыл бұрын

The rubber tube is always attached to the mass damper. flatbed screw is "Item No:15510　STAINLESS STEEL COUNTERSUNK SCREW SET (10/12/20/25/30mm)" But Eyelet only comes with the old kit.

Sensei , what do you think about front pivot system without AT? Do you think its better for 3 lane race in a technical layout?

@AZARASHI3ODN

3 жыл бұрын

The pivot provides running stability. AT has a stable jump. Having both gives you double stability. However, the pivot slows down the cornering speed. So if you want speed, the AT-only configuration is the best.

@heheyeaaboii4358

3 жыл бұрын

@@AZARASHI3ODN the thing is most tournament in my country using 3 lane technical layouts with extreme corner and jumps,and every contestant could have an unlimited race coupons. So a strong solid desgin its needed,meanwhile the AT system seems a bit fragile with this regulation. Except when i race in official TAMIYA arena in my country,they use 5 lane layout, yesterday i tested your desgin and its AMAZING, beating my personal records!

Hi. I’m new. Can I check with you what’s that black color thing on top of the rollers?

@AZARASHI3ODN

4 жыл бұрын

This parts is "Item No:15413:RUBBER BRAKE SET"

@21fhs

4 жыл бұрын

@@AZARASHI3ODN thank you!!

where do you get the small rubber ring? or from which part is it?

at the last picture what bearing did u use at the upper front? is it 13mm? and at the middle need not put any damper?

@AZARASHI3ODN

5 жыл бұрын

The last photo shows an 11 mm bearing on the top. But the upper and lower 19mm is more stable. The mass damper is more stable if it is in the middle, but it is faster because it is not.

@dhiyamohammad1756

5 жыл бұрын

@@AZARASHI3ODN meaning the 11mm bearing must be replaced with 19mm roller to make it more stable right? orite thanks bro

@AZARASHI3ODN

5 жыл бұрын

@@dhiyamohammad1756 Yes, 0 thrust transfer can not be performed well if the upper and lower diameters are the same.

@dhiyamohammad1756

5 жыл бұрын

@@AZARASHI3ODN i didn't get it too well actually. Haha. What does it mean by 0 thrust transfer?

@AZARASHI3ODN

5 жыл бұрын

@@dhiyamohammad1756 It is a mechanism to set the thrust angle of the roller to 0 degree while traveling. If it can be done well, the corners and straights will also speed up.

Hello sir .i tried to make at bumper like this.its working fine but the bumper very shaky left and right,any suggestion?

@AZARASHI3ODN

3 жыл бұрын

This bumper is easy to swing from side to side. Therefore, if you use the HIKUO arm to fix it to the chassis, it will be less likely to shake.

@heheyeaaboii4358

3 жыл бұрын

@@AZARASHI3ODN i get the point sir,but i dont have an idea how to do it properly, if you dont mind could you deacribe it to me or ahow me a pitcure of it? Thanks a lot sir.

@AZARASHI3ODN

3 жыл бұрын

@@heheyeaaboii4358 The shape is a little different, but you can see the theory in this video. kzread.info/dash/bejne/rGGFp6SMYK_Je8Y.html

@heheyeaaboii4358

3 жыл бұрын

@@AZARASHI3ODN thank you so much sir! Its solved my problem.

I want to send you a video of what I made - maybe you can tell me if I did it correctly ....~

@tonypapagna6027

4 жыл бұрын

How can I send you a picture ~?

Hi.. may i know the parts on the bottom of front bumper did you use? And what is the meaning of "you put the POM for the counter gear around the back of the screw"? POM is some tamiya parts? Btw its a great video..

@AZARASHI3ODN

5 жыл бұрын

POM is Poly oxy methylene. It is a part that substitutes for the bearing attached to the MS counter gear as standard. kzread.info/dash/bejne/qqyL0tKMlby6hqg.html Put it in this position.

what is this cowl???

@AZARASHI3ODN

5 жыл бұрын

This cowl is Avante MK2 + Aero Avante(Canopy Only). "Ava"nte MK2 + Ae"ro A"vante = Ava-roA !!

Kawul very nice Kawul name or item number please~!

@AZARASHI3ODN

5 жыл бұрын

This body is Avante MK2 + Aero Avante(Canopy Only). "Ava"nte MK2 + Ae"ro A"vante = Ava-roA !!

Blurry.. blurry everywhere..