Embossing Folders, how to get the right sandwich for 3D folders and others

3D Embossing folders and how to get the correct "sandwich" using Big Shot or Big Kick.
Find me on Facebook:
profile.php?...

Пікірлер: 20

  • @amjPeace
    @amjPeace2 ай бұрын

    This is the best video I've seen on embossing folders. Thank you, Brenda! I learned a lot!

  • @brendafertitta857

    @brendafertitta857

    2 ай бұрын

    Aww! Thank you so much! I am so glad it helped you!! Thanks for watching!

  • @maryrakas4901
    @maryrakas49012 ай бұрын

    You answered my question perfectly! Thank you so much

  • @brendafertitta857

    @brendafertitta857

    2 ай бұрын

    You're welcome! Thanks for watching!

  • @TheMountainbobcat
    @TheMountainbobcatАй бұрын

    nuts, sizzix 3-D folder and the big kick/shot was what i was looking for, but after trying a couple times found , four to five sheets of card stock along with tab 1 and a plate sorta did it.

  • @brendafertitta857

    @brendafertitta857

    Ай бұрын

    They can be tricky for sure! Thanks for watching!

  • @orchardgirl4785
    @orchardgirl4785 Жыл бұрын

    Brenda, Thank you for this demonstration. You answered my question, and I learned so much more. What a blessing . Thanks, again.

  • @brendafertitta857

    @brendafertitta857

    Жыл бұрын

    Wonderful!! I am glad to help! Let me know if there is anything else I can help you with. And again, thanks for tuning in!

  • @orchardgirl4785

    @orchardgirl4785

    Жыл бұрын

    It's been a pleasure. This week I am watching all of the napkin technique videos and making some of those. :)

  • @brendafertitta857

    @brendafertitta857

    Жыл бұрын

    @@orchardgirl4785 great! I hope you enjoy them

  • @bettiestrong4051
    @bettiestrong40514 ай бұрын

    I appreciate that you made this video. I have a Big Shot and the Stampin' Up 3D plate. I tried it the way you showed, and it wouldn't go through. So, I wondered if I used it on tab one, if it might work. I'm glad I watched the video to the end, as you actually mentioned doing so, as a remedy for that. Thank you so much!

  • @brendafertitta857

    @brendafertitta857

    4 ай бұрын

    Glad it helped! Thanks for watching!

  • @patriciafarrell424
    @patriciafarrell424 Жыл бұрын

    Brenda - You just said that with directional embossing folders, we may have to run them through the cutter open end first, not fold first. I thought that would crack the fold.

  • @brendafertitta857

    @brendafertitta857

    Жыл бұрын

    Thank you. I have tried to email you back about the cardstock samples and it bounces back. Can you please email me again and include your email address in the body of the message? Thanks

  • @patriciafarrell424

    @patriciafarrell424

    Жыл бұрын

    @@brendafertitta857 Brenda - not sure what is wrong with the e-mail. It seems to block some incoming items. I will pass on the Cardstock for now.

  • @brendafertitta857

    @brendafertitta857

    Жыл бұрын

    @@patriciafarrell424 ok

  • @margarettaylor3033
    @margarettaylor30339 ай бұрын

    Hi, I enjoyed your video, now a Question? I have a lot of used embossing folders that do not have the paper line printed across the bottom of them, can you measure how far up the line is from the edge of the folder and provide the measurement? Do you think that I could just mark this line with a permanent marker on the used folders to create the same effect? Just looking at the video it looks to be about a 1-inch mark. Hope that makes sense?

  • @brendafertitta857

    @brendafertitta857

    9 ай бұрын

    Hi! Thank you for the question. I measured a few and they are all a little different, ranging 1/2" - 3/4". You can also line your paper up along the edge where the embossing starts/ends thst works as well.

  • @margarettaylor3033

    @margarettaylor3033

    9 ай бұрын

    Thank you so much for taking the time to do the measurements, I'm new to all this embossing/cutting, as I just got a used ( the old red and white one) Sizzix at a thrift store, so I'm buying a lot of used stuff to get started and don't know how to use it so I've been watching a lot videos. Thanks again for your video I learned a lot and will probably go back and catch up on your other videos.

  • @brendafertitta857

    @brendafertitta857

    9 ай бұрын

    You're welcome! Feel free to reach out any time! I eould love to help you in any way I can! Thanks again for tuning in!