I like the fact that you used the existing wire for the repair and not a brand new one . Zero waste.

I admire these educational videos and find them very useful since most of the times I try to fix everything myself. Thank you for giving take by take instructions!

Excellent video. Comprehensive. Detailed. Outstanding job!!!

How do you take the motor out from the tyre? It doesn’t show in this video, and just skips right through it. Anyone know how?

Nice video. Usually i don't much like non- verbal instructional videos but you do such a great job with the camera angles clearly showing the viewer what you're doing that it works just fine. As a bonus, you don't have any of the cringe-inducing music that most people usually overlay on top of the video. Gold star for you, bucko!

This video was very useful as i needed to help my friend with motorcables

ur are really the best tech i ever see

Very useful video ! Thanks so much !!!🙏🏾🙏🏾🙏🏾

Foarte bine, felicitari.

Thank you for sharing my friend

Great and helpful!!

Nice video, I love that broken soldering gun in trash 😂😂

pretty clean repair

Thank you!

Sper sa nu aveți probleme niciodată cu senzorii hall ca nu e o experienta plăcută. În special când lucrezi cu un motor electric pentru bicicleta qs273. Foarte bun video-ul, felicitări.

Wicked skills 👌

Really good video, learned a lot! Thank you! I am facing another problem, it seems like the big bolt on my scooter which is going through the center of the motor is bended. So is there a way to change it with a new one?

One tip for the Motor Hub cover. Before putting it back seal it with some Cylinder Gasket Glue (silicone) to prevent water from entering there to corrode stator core.

Great video man👊🏼🙂

Man this is absolutely brilliant I had the exact same issue with my Apollo light motor after going over a curb and grazing the wires to the point with our exposed so I kept getting an e error but just like you I had the exact same idea to rethread the wires through the only difference was I was going to do something stupid and try and connect all otherwise together rather than desoldering the wise and then threading it through and re-soldering a new loom if you have any other advice or ran into any other small problems I would love any advice please ALSO DO YOU THINK IT WOULD BE POSSIBLE TO REPLACE THE MOTOR WITH A MORE POWERFUL ONE OR WOULD THE BATTERY NOT BE POWERFUL ENOUGH

Good job.

Do you need to grease the magnets around the wheel? I feel like there is a bit of friction between the magnet and the stator in my brushless motor.

Super video respect maxxim

good job

Parabéns pelo video, muito bem feito. Foi muito importante ter adicionado a lista de material. Só não vi, o link das luvas que utilizou. Grato. Brazil 🇧🇷

I have a similar hub motor and I have to replace the 3 hall sensors because 2 wires of them are cut!! I was wondering what is that white paste that you remove in the begging and is also located on the top between the 3 sensors and the chip. I am thinking to put a glue or something like a glue to avoid the movement of the chip and the sensors also and avoid of cutting the wires of the sensors again. Please help me!

Nice video.

I like your screws :)))

Are the bearings you replaced enter than the other ones as they are different?

super

Great vid. Suppose you could have checked the Hall sensors are OK, since water got inside? 5v PSU, DVM, 10K Ohm pull-up, turning wheel and checking A, B and C outputs at the cable connector end. Just a thought. 😃

@DrDrei

2 жыл бұрын

I had the scooter there and got to test it, works like new even today 👌

@chillyboy2008

2 жыл бұрын

The 3 big wires to the coil, does it matter the order of them? How they are connected to the coil?

My escooter speedometer went then shortly after the motor jamed up gets stiff when u speed up but spins OK when off ground what u think it is

Is the motor wired in Delta or Star connection? Could the power be increased by rewiring the motor?

Hi guy, thank you very much for your smart video; it’s very helpful; could you please tell me the right name of the cable or where to find it? I need to replace it from my 20LVXD30 SAMEBIKE, thank you very much!

Great video. Did you just disconnect other end of wires from inside scooter, was thare enough extra wire to make up for the damaged part

Sincer... nuj daca erai 'mester' inainte sa iti iei prima trotineta... dar dupa ani si ani... si cu asa scule... bro esti profi, with no doubt about it. Also, place stilu asta de editare... stiu ca ia mai mult... (ca timp) dar e fain. Cred ca o sa am si eo nevoie de serviciul tau curand pentru verificare rugina la motor si posibil schimbat rulmenti :)

Great video, I should try this tomorrow. Rear motor showing an error, Contacted Kukirin 3 weeks ago & still waiting to find out what's happening with the new motor, been advised used not to rush them .. Its still under warranty but ill probably be waiting months again missing out on summer with dual motors. Motor isn't working so might as well try .

Sir ,what a position of hall sensor? 60 or 120 ? I have bldc like you from minimotors 60v 800 watt but this motor without hall sensor , can i added hall sensor on my bldc?

Nice

That spring u cut a piece off of. Does that go inside the nut?

What wire did you use as a replacement for the one you cut off and how did you connect the connectors on the speed controller end

@saville1712

Жыл бұрын

Hello, I've had similar issues. You may need to buy adapter pieces and build your own connection by soldering. Its not hard at all just steady hands and patience.

nice work pal you hv new sub great channel and great vid i will look forword for more great stuff

@DrDrei

2 жыл бұрын

Thanks 🙌

What are the 3 sets of yellow wires attached to board and copper

hey, just a quick question. Can help me with figuring out how to reconnect those little yellow wire that connect to the coil

@DrDrei

2 жыл бұрын

You need to sand the tips before soldering them, to remove the protection layer so that it sticks to the wire

I enjoyed your video and learnt something... Now, for a wee joke. If you clean the magnets and polish them, it will give you added power and performance! 👍 (Sorry, reminded me of the C.B days) They said if you polished your attenna, you were definately going to make long distant contacts. 😂

Nice bearings but they've only got a dust seal. Go back to the rubber seals to keep more water out.

Hola buenas, muy bueno tu vídeo, quisiera saber dónde se puede conseguir un soldador como el tuyo, muchas gracias!👍👍

what hub motor is that im looking to upgrade to a 1000 watt motor i have a 350

My hover- 1 alpha turns turn on and works fine when I have the handle bar turn left but when if turn to the right it shuts off and won’t turn on when it turn to the right

How do you remove the rotor when it's stuck? I can't seem to remove, mine.

nice scissors bro,, work like a charm hehehehehe

Great video! I'll need to do this someday on my wheel. There are some bear copper spots on all the main wires and some of the hall sensor wires right at that same area in this video. On my other scooter, I am having trouble getting the plate off to look at the hall sensor wiring. I am getting an e-001 error code on my tf-100 display. It was easy to get the plate off my currently running scooter. But this other one is hard and I was worried about the plate breaking since I already chipped a tiny piece already during attempts.

Thanks for the video. Where did younger that replacement cable?. I am looking for 3x4mm² cable for my e scooter and cannot find it anywhere

@DrDrei

2 жыл бұрын

It's the same cable, I just cut a part out

@DrDrei

2 жыл бұрын

bit.ly/3E25j92

Hello friend, is it this size bearings Ok for Zero 10x? Thanks and GREETINGS FROM SERBIA.

Subbed.😁

What is that cable called? I don't find in the link you have provided.

@aaqibhussain426

7 ай бұрын

Can you let me know please??

hi can tell us about the code of the sensors

Faltó la prueba de funcionamiento

my motor show fake temps can I cut the heat sensor wire ?

salutare! am si eu o intrebare, se poate adauga o noua baterie pe o trotineta electrica? De ex o trotineta cu 48V 20ah la care adaugam o baterie acelasi model, va dubla range-ul trotinetei? se pot face astfel de modificari?

@DrDrei

3 жыл бұрын

Sigur ca se poate, sunt multi cu xiaomi care fac asta deja

Very nice video bro , i have a question, maybe you know where i can find that cable in Spain ? Thanks a lot

@DrDrei

Жыл бұрын

Check description links

My phase wires are not accepting solder. What should I do?

@klg1001

Жыл бұрын

Higher wattage soldering iron, tin your wire and soldering tip before making the connection, use flux.

Where i can find sensors?

hi, anyone knows whats the hub bearing size of kaabo wolf warrior 11+?

@klg1001

Жыл бұрын

Did you ever find out the number?

What's the size of that seal at 6:54

Buy a Hakko soldering iron. Best you can get

LOL I feel you on that shitty soldering Iron....I learned the hard way too...I'm pretty sure mine went out a window...

I would say be careful when putting the stator back with the magnets the stator can hit the magnets and chip one. As you can imagine that won't be good

When you threw the soldering iron in the bin. 😂

Salve, io ho bisogno di un aiuto, ho un monopattino laotie ti 30 e il motore posteriore non ha più la potenza che aveva un anno fa come mai ?

Thanks. Im not so smart but im persistent. Ill see today what ill fix

Excellent video. I am repairing the wires on a similar if not the same unit. I bought a 9 pin extension cable but don't know where the small white wire connects, if it is used at all. Doesn't appear in your video anywhere. Could you verify that it is or isn't used? thanks for your help.

@gabyshorts

8 ай бұрын

Not used

salut,am si eu o problema la blocajul din ghidon inainte se misca stanga dreapta pana intr-un punct acum nu mai are puncutl acela maxim ce pot face?(xiaomi m365)

@DrDrei

3 жыл бұрын

Intra pe grup te rog și postează

@alexchiri2923

3 жыл бұрын

@@DrDrei aveti grup de discord?

Where can I find this tool to remove motor hub from bearing

@DanceySteveYNWA

2 жыл бұрын

It's the top listed item in the products in the description

How do I remove the centre

Never grind the stacks of laminations in the stator - this can result in a significantly higher operating temperature and lower motor efficiency due to the increased fault current between the individual laminations. As a reason, look for the disadvantages of transformers with welded transformer sheets.

Haha, did you hear the argument in the background? Hard to hear, but I made a few things out.

could I throw some Bones Swiss bearings in there for better performance?

@yassasloan7308

Жыл бұрын

oor does have to be a certwsize

👍👍👍👍👍👍👍👍👍👍

Yo you didn’t show how to get the whole motor out the tire I have the same one but I can’t get to that one bearing at the bottom please hit me up I need help

yuo doing will we love you.

Do you have a repair shop? Where is it located sir? My ebike needs to be checked by an expert like you...

before closing motor lid, would be nice to seal it with some hermetic

Where do you live I need my hub motor to fix

Does it work though?

@DrDrei

Жыл бұрын

Yes, installed on scooter

unde pot sa gasesc acele garnituri 6:54

Brake disk installed in wrong direction if it looks on right side of kick scooter. It a arrow direction. Entire motor looks like is from Kugoo M4 pro.

thats very good info, but I think I'll just buy a broken scooter and take the whole wheel hub

@DrDrei

Жыл бұрын

yea if the axle matches

Au unghia :))

1/2 joking. Thanks for the work

You have to laugh when he chucks the soldering iron in the bin...

Man, all the tools and work involved good job, But I say F___K it. I'm going to buy a new motor or sell it. Motor 250.00. Paid 910.00 for a 2000w freego. Oh, I hit a deep puddle there not under water machines. Maybe shorted the fuse. But there must be rust inside with mine.

Hello can you fix mine bro pls I give you money for fix Can you do it 🥺

I wish videos would skip showing screws being turned, and other waste of attention, and just get to it

And then you dip the whole thing in wd40 for a week

you can afford to buy a new soldering iron but you cant get a proper wire stripper, i dont get it

What are the 3 sets of yellow wires attached to board and copper