Electric Furnace for Melting Aluminum
Тәжірибелік нұсқаулар және стиль
I built an electric furnace for melting aluminum cans efficiently and easily.
It has 600w x2 electric heating wires.
If you like it, please subscribe to my channel.
See my Instagram for more of my work!
/ 7chome_seisakusyo
他の製作品のご購入はこちら(日本国内のみ)
www.creema.jp/c/7chome_seisak...
#DIY#Howtomake#Can#Aluminum#Melting#ingot#ElectricFurnace#Furnace
Пікірлер: 84
The design is wonderful. I learned a few new materials. Great use of electricity; I was going to run 240v but I think 2x 120v is smarter. Please consider using proper tools and avoid setting crucibles on concrete; it could explode! I like your design the most from what I've seen and will emulate it with a much larger build!
@7chome_seisakusyo
29 күн бұрын
Thank you!
I learned a lot from watching this. Thank you for the video.
@7chome_seisakusyo
10 ай бұрын
Thank you!!
A very tidy, high-quality job.
@7chome_seisakusyo
Жыл бұрын
Thank you!!
Hola, buen trabajo con el horno electrico, por favor permitame darle una recomendación, no use ningun tipo de madera cerca del horno, se maneja alta temperaturas y resulta un peligro, cualquier pequeño escape de aluminio fundido provocaría un incendio. Un Saludo.
@7chome_seisakusyo
2 ай бұрын
Thank you.
What a pleasure to watch. Love that your son came in to help. Mine use to help all the time but now video games rule his free time lol. Going to make one like yours. Thanks a bunch for sharing.
@7chome_seisakusyo
Жыл бұрын
Thanks for the comment! My son also went to play video games right after this. I guess all kids are the same... I would love to see the can crusher you built!
Beautiful job! Thank you! But be careful when taking the crucible out of furnace whilst it's plugged - you may be electrocuted from the spiral through the tongs
@7chome_seisakusyo
Жыл бұрын
Oh! I thought I had turned it off. Thank you!
Very nice and to the point build. Thought it was soso till you placed blanket around the brick❤. The last blanket could be regular house insalation to save money. Really nice job!!
@7chome_seisakusyo
8 ай бұрын
Thank you!!
thank you for your video
@7chome_seisakusyo
Жыл бұрын
Thank you !!!
note to myself for future: someday i will try to make this furnace.
@7chome_seisakusyo
Жыл бұрын
Good luck!
That brick will damage your lungs if you dont wear a mask that can filter it, especially when cutting it on a power saw.
@7chome_seisakusyo
9 ай бұрын
Thank you!
@DigiLab360
9 ай бұрын
Agree about the bricks and the fire wool also. They contains silicates which once inside the lung, cannot escape leading to a lung condition called silicosis. ALWAYS wear a respirator when working with silicates. Fantastic build! 👍
@facttell6779
8 ай бұрын
@@7chome_seisakusyo is it a distribution strip
É show muito legal mesmo, profissional
@7chome_seisakusyo
Жыл бұрын
Thank you!
Thank you very. I was so amazed to watch your video. Are you connecting to a power outlet or to generator
@7chome_seisakusyo
10 ай бұрын
Thanks for the comment! I just have two 600W kanthal wires connected directly to the outlet in parallel.
شكراً لك على هذه الطريقة وعلى المهنة سؤال هل بي الإمكان صنع فرن للفضة أو الذهب قوة شريط الكهرباء كم و فيما إذا كانت الألواح الشمسية تشغله بدون كهرباء ممكن شكراً لكم من دمشق تحياتي لكم ❤❤
@7chome_seisakusyo
8 ай бұрын
Thanks for the comment. The power supply is 1500W. I don't know about other questions, sorry.
ما الفائده المعدن يمكن ان اصهره في تكلفه اقل من هذا لماذا لا تجرب الذهب او معدن اكثر صلابه
@7chome_seisakusyo
29 күн бұрын
I am very interested in copper melting and it is one of my dreams to try it!
If I am not mistaken, the hand mixed heat resistant cement is called refractory. Great build! I thought when you hand made the lid / top and matching plug, it had to be initially fired (no metal to melt), then it was ready for use with metal. Did you make the crucible too? Thank you 🤓
@7chome_seisakusyo
9 ай бұрын
Thanks for the comment! The cement I used is fireproof. Quenching is not necessary, but I did it just in case. I didn't add reinforcing steel bars to the lid I made in the video, so it cracked after a few uses. So I rebuilt it after this with reinforcing steel bars. The crucible was bought from amazon. Please check out my other videos!
@j.lietka9406
9 ай бұрын
@@7chome_seisakusyo very welcome! Thank you for all the great answers! Domo arigato
12:00 heatgun for this step does the job for me.
@7chome_seisakusyo
8 ай бұрын
Thank you!!
Please can you explain the wiring. I understand the coppet electrodes, kathaline wire, but not the rest of the connections
I finally got bit by the metal melt bug and want to get into this new hobbie. Im looking it maybe a DIY version but which is better or cost saving, as far as spening money on gas vs electric? Also which melts faster gas or electric? Thanks for any advice and info keep up AMAZING vids!!!
@7chome_seisakusyo
8 ай бұрын
Hello! Thanks for watching! Welcome to the world of homemade metal melting! I live in a small residential area, so using a gas or other fire is a bit difficult, so I built an electric furnace. If your place is large and gas is easily available, I would prefer to make it with gas. I would also build a gas furnace if I could. I wish you success and enjoyment!
how did you find the billet density.? I've heard that vacuum assisted casting, even billet will make for a more uniform/dense result. Great build!
@7chome_seisakusyo
4 ай бұрын
Thanks for the comment! I did not measure the density of the billet, but the porosity was less than I expected.
Very nice. It's a well-thought-out, clean build and seems to function as intended. Do you have an idea what the inner volume of the oven is? I am wondering if your stones are 4.5 - 9 - 2.5.
@7chome_seisakusyo
4 ай бұрын
Thank you for comment! The internal volume is about 1 liter. The size of the refractory brick is 230 mm x 110 mm x 65 mm.
@pilotarix
4 ай бұрын
@@7chome_seisakusyo Thank you, that is helpful to know.
Always preheat your molds, u'd get a better results! :)
@7chome_seisakusyo
10 ай бұрын
Thank you,Of course I do preheat.
How much faster did it take to warm up compared to a small 2-3kg furnace?
@7chome_seisakusyo
Жыл бұрын
Thanks for your comment! I don't know how fast a small furnace weighing 2-3 kg is, but my electric furnace takes about 1.5 hours to reach the temperature at which the aluminum melts.
Why not add another element coil in parallel or cut that one into smaller ones? Was that the limit for the wire gauge and the breaker in the circuit you are plugging it into?
@7chome_seisakusyo
Жыл бұрын
This coil is 600W and 100V, so two coils are flowing 12A in parallel. I would like to make 3 coils in parallel, but 18A would exceed the outlet rating of 15A. I certainly need more power...
hello, to melt aluminum faster, can i use a steel crucible and with the wires more closer or attached to the crucible? which transmits temperature better, a sand crucible or a metal crucible?
@7chome_seisakusyo
8 ай бұрын
Thanks for the comment! My crucible is made of graphite. Both iron and graphite are conductors, so it is dangerous to put the wire too close to the crucible. If you want to melt faster, you may want to increase the power or improve the heat retention.
Nice job. 👍 How long it takes to melt aluminum
@7chome_seisakusyo
3 ай бұрын
About 30min. Thank you!
hello,question: if place the aluminum oxide at temperatures reaching 1200 Célsios, l con modify its structure, thus obtaining mono crystalline alpha alumina ?
@7chome_seisakusyo
4 ай бұрын
Sorry, I am not familiar with it.
how about amperage? 20a ?
@7chome_seisakusyo
11 ай бұрын
This coil is 600W and 100V, so two coils are flowing 12A in parallel. I would like to make 3 coils in parallel, but 18A would exceed the outlet rating of 15A. I certainly need more power...
Is you use distribution strip ?
@7chome_seisakusyo
8 ай бұрын
Yes.
And can we adjuste the heat adding any control ?
@7chome_seisakusyo
11 ай бұрын
kzread.info/dash/bejne/o66ju6dvda2uc8Y.html Please refer to this page. However, this thermocouple has a heat resistance temperature of 1300°C.
Zašto uopće topiš aluminij?Koja je svrha?
@7chome_seisakusyo
29 күн бұрын
I make mechanical parts from molten aluminum. kzread.info/dash/bejne/ZJp_q7impLzWnbA.html Yes, I understand it is cheaper to buy them. Simply because it is fun.
❣️
@7chome_seisakusyo
Жыл бұрын
❣
how many volts and how many amps how many watts ?
@7chome_seisakusyo
Жыл бұрын
100V x 6A = 600W x 2coil = Total 1200W
Ceramic tube is best option for insulation i think
@7chome_seisakusyo
Жыл бұрын
Thank you!!
Please la resistance utilisé combien d empere
@7chome_seisakusyo
Ай бұрын
It is a 100v / 600W resistor, so about 16.67 ohms.
Mad building , those screws can catch on fire outside that contraption. Know what doesn’t hold onto fire bricks, you don’t drive a hole init for anything molten hot beyond 2090 Celsius
@7chome_seisakusyo
Жыл бұрын
The temperature will not be that high.
Can u please tell me. I want to get heat up to 1800c is it possible to get that using this?
@7chome_seisakusyo
11 ай бұрын
Thanks for your comment! How many degrees you can reach depends on the amount of heat generated by the coils and the heat retention of the furnace. To reach 1800°C in a less powerful electric furnace, I think you would need to increase the thickness of the firebrick walls by about 3 times. I would also like to build a larger furnace to melt copper!
@genericuser4266
11 ай бұрын
@@7chome_seisakusyo Assuming they are using nichrome resistance wire, which is what most furnaces use and what you appear to be using, you can't get to 1800C because nichrome melts at about 1400C. I'm not aware of any electrical resistance heating wire that can withstand 1800C. If I am in error please correct me as I would like to be wrong. It would be much better if the wire could get that hot. To get to those temperatures the options I know are: gas furnace, arc furnace and coal. Arc furnace is cleanest and easiest to build at home, but shock hazards must be accounted for.
@7chome_seisakusyo
10 ай бұрын
Oh, I had completely forgotten about that. You are right. Nichrome wire melts at 1400C. If you want to do it with electricity, maybe use an electromagnetic induction coil?
@genericuser4266
10 ай бұрын
@@7chome_seisakusyo That's a good idea, I'll look into building one. I forgot those existed. Thank you very much for the suggestion,
@venuthandnalinroundtheworl8249
10 ай бұрын
But the problem is i need this furnace to heat minaral stones . Is it possible to use electric magnatic furnace for that purpose ?
Arigatou gozaimasu, demo kako shimasenka?
@7chome_seisakusyo
4 ай бұрын
Thank you! kako??
@gendaminoru3195
4 ай бұрын
@@7chome_seisakusyo copper desu
@7chome_seisakusyo
4 ай бұрын
Yes, I would like to melt copper someday!