I love the videos and watch them more than once. Thank you!

Thanks Kim! I am going to attempt my very first project this weekend😱 I am nervous but, knowing have this video at my fingertips makes me feel so much better.

Thank you Kim. I have done a table runner but will attempt a lap size quilt. The drag and drop looks pretty simple but I seem to always come across something "new" to deal with. I learn something new each time, again thank you.

Thank you Kim so much for going over how to turn off the pro stitcher and also how to do edge to edge because I have not done it yet I’ve had my machine for an awful long time and I’m gonna do it today thanks bunch I hope it works out OK😬

this video saved me! Thank you so much!!!❤

Just got my pro stitcher premium used it last night for the first time! I’m assuming you go to that line across the top and match the crosshairs , maybe the green dot ?? I’m Not sure either ! but I ended up going over my second row Slightly while doing my third row….🤔so yes the first time I did it right ( but could have been a bit closer ) of course a practice piece !

Thank you for this video. I has been very helpful

Do you have to download the app

I just acquired a 2016 Avante on a 10 ft frame running Pro-Stitcher Premium 2016, v 17.010405, which I realize is outdated, but will work on that in the near future. My current question is... Following the instructions for this video, I set up an edge to edge design, just a single row, for practice. It stitched nicely, but when it got to the end of the row, it stopped stitching and then I could not figure out what to do next. The machine would not move, so i could not pull up the bobbin thread and tie off. I ended up turning off the motors, which did free up the movement of the machine, but I am guessing that is not the correct proceedure. Please advise what I should have done instead. Thank you.

I’m not comfortable leaving the needle down when I roll, but this is possible without leaving the needle down if I’m not mistaken. You would manually move the machine to a spot and hit drag. Please correct me if I’m wrong.

@ProStitcher

Жыл бұрын

kzread.info/dash/bejne/mnxkpaejfreZdtI.html If you watch at about 12:00, we cover repositioning without putting the needle in the quilt.

@sherm2u

Жыл бұрын

The video ends at 11:05

@lyndabuchholz1216

Жыл бұрын

@@ProStitcher No 12:00! I would like to know this also!

@colleenpedretty4248

Жыл бұрын

@@lyndabuchholz1216 The video link is right above the 12:00. It's a different video, not this one.

@lyndabuchholz1216

Жыл бұрын

@@colleenpedretty4248 I am not seeing a 12:00. I will keep looking.

I’m having issues with my needle and the many seams I have on my quilt top. What needle do I use? I used the one it said in the moxie manual. BTW, I didn’t have issues until I got PSL. Thanks

@ProStitcher

Жыл бұрын

You will want to use the needle size that matches your thread weight. It is the same with PS as with free motion.

Do i need to reduce my design for e2e since I have the Moxie & Pro-stitcher lite ? This video did not show setting up the frame space, just the area space....Is this different between Prosticher & Prostitcher Lite ?

I have the Prostitcher Lite, when watching the educational video for the Lite, when I advance the quilt, I keep getting an error (outside the frame space), then I'm stuck and don't know how to recover from the error. When watching this tutorial, it is a lot simpler than setting up a 2 corner area, then select the design and set up another 2 corner with the length of the quilt. Can I do the edge to edge as shown in this tutorial with the Lite? I hope so... this is way easier and I think I could do it without the frame space errors. I did read the comments on the other video I was following & someone pointed out the video example was wrong, and maybe that's why I'm getting the error. That brings me to another question, am I limited to just the Lite tutorials, or can I learn from the regular Pro Stitcher tutorials, like this one? Thanks

@quiltartdesigner1456

Жыл бұрын

I tried doing it this way with my Pro Stitcher Lite, it doesn't work without first telling it the quilt space with the side bar 2 corner. I am able to stitch my first row, but when I advance the quilt as shown on the Lite video of edge to edge... I keep getting the error (outside the frame space) then I don't know what to do to continue. Is there another tutorial to show what I am doing wrong or get help???

Anybody know if there’s a pdf of this?

I saw a viedo that had a duck with the drag and drop. I didn't see it on yoour screen. Is that important to touch the duck?

Is anyone else having difficulty getting this to load and play past the first few minutes?

@skiptonius5346

Жыл бұрын

Nope

You didn't really explain how far you advanced to get equal spacing between the rows . I'm still not sure how to fully use this feature.