I never comment on videos like this, but I gotta say making this without some stupid ass music and a bunch of "humorous" voice over b.s. makes it the #1 how to video I've ever seen. And I've watched a bunch. To bad it's not the rule by which all similar videos must comply to. I can't thank you enough for taking the time and doing this the right way...

@MrSubaru1387

5 жыл бұрын

Glad you enjoyed. 👍🏻

My fuel pump finally died. Just rewatched your video to freshen up the brain on what I’ll need to do. Thanks for keeping it to the point and not blabbering on about unnecessary $#!T. 👍🏻

For future reference, that red clip on the connecter is called a secondary lock. You need to slide it over, then push on the tab to remove the connector like normal. That's why you had a difficult time removing it. I'm actually surprised it didn't break when you pulled it off. Chrysler has a red lock on almost every wire harness connection.

I like the no commentary. Great job. Doing my 98 cab corners this weekend. Fuel pump while its tilted.

great to the point video and no one over talking what needs to be done for 20mins

@MrSubaru1387

7 жыл бұрын

+wally so glad you enjoyed the video

@TheImpaler92

7 жыл бұрын

I got to do mine over the weekend outside and I live just outside Chicago,i'm gonna hate doing it but much easier than pulling a full 35gal tank and it don't fit in my garage,but thanks for the great video

I was a Honda tech for over 10 years Honda school trained. I am disabled now still work on car's I try to show people some of the easy way's to do a lot jobs . some are so simple if you look at it a little different.

I just did this on my 01 Cummins to replace the fuel level sending unit except I used a floor jack and a 2x4 from under the bed then supported the bed with a big block of wood, worked great and fixed my 1/4 tank issue.

@MrSubaru1387

9 жыл бұрын

Great. Glad to help.

Good job! I’ve dropped gas tanks by myself laying on my back in the driveway and always thought ‘never again’, but this approach looks doable.

Thank you so much. Me and number one son did it today - it took 4 hrs, but we ended up looking for tools and had trouble with the gasket to move that piece into the new pump! You are a lifesaver, but I wished more than once that we'd had your winch! So good to hear the truck run again :)

I hope you don't mind but I saved this video for me to do the same thing with my 2001 Dodge Ram 1500 this weekend. put on my phone so I can reference it without having to get out from under my truck. Best video on this subject out there!! Three Thumbs Up!!

The only thing missing was the removal of the ground strap between the cab and the bed. Thanks for the video. You saved me a lot of time and aggravation.

You're very Humble not to take a Bow at the end of the Vid, Genius!!!....you've done in minutes what would take hours and knuckle busting ...great Info

Best video for fuel for replacement

Excellent video! I replaced the fuel pump on my 99 Ram last weekend using this video as a guide. Was much easier than dropping the tank. I did have to remove the rear bumper to allow the bed to be tilted far enough.

@MrSubaru1387

10 жыл бұрын

Glad the video was helpful to you. Thanks for the feedback.

I watch vids on subies and yellow makita watching you for lest 2 years. Awesome to know you have vid to for my dodge

Getting ready to install an aftermarket check valve, this helped me locate the ONE place I can find soft fuel line to put it.

This is an OUTSTANDING video. I appreciated the comments rather than the talking. It allowed me to pause the video and really get what you were explaining. By not cutting the hole in the bed, I was able to preserve it's integrity. And with an almost full tank (isn't that when crap like this happens?) your solution is perfect! Thank you, sir!

I just did this on my 1991 W150 and it was the same and worked great! I'll never do it any other way. I didn't want to drop the tank because I had just filled it the day before the pump went south on me! Thanks to the poster for posting this!!!

@MrSubaru1387

7 жыл бұрын

+Kevin Vaughn glad to help!

@greatestskills7447

6 жыл бұрын

why do they always seam to go right after a fill up. I had a gmc truck that the fuel pump quit at the gas pump when i tried to start it right after a fill-up

@MrSubaru1387

6 жыл бұрын

GM trucks are notorious for that. Lol

Very fine tutorial. Video illustration was extremely clear and concise. This is exactly the way a video of this type should be done! Thanks!

@MrSubaru1387

7 жыл бұрын

+the1realanalogman thank you. Glad you enjoyed it.

This was the best straight forward video on changing ram1500 fuel pump..I put a piece of duct tape or rag into gas filler to keep screws from falling into tank when unscrewing/screwing in.

Good video... fast and on point.. no annoying music and slide shows.. thanks for the helpful video

@MrSubaru1387

9 жыл бұрын

Thanks, glad to help.

Thank you for the easy to follow instructions on how to change the fuel pump on the Dodge Ram. I have acquired a non running Ram and I'm not getting any fuel to the rails. Lifting just the front of the bed in your video is going to save me so much time accessing the pump and fuel lines. And, I can do it by myself and not need to ask a neighbor to help me take the bes off. 👍 to you sir

@MrSubaru1387

9 жыл бұрын

Glad to help!

thanks for being very detailed on the repair i just bought a 97 ram 4x4 for 700 dollars and this was the problem. You saved me alot of money on a repair thanks. We have to keep older trucks on the road because the new ones are so freaking high!!!! no such thing as a plain jane any more every body wants a luxury truck nowadays! Keep up with vids!

Thank you for your very good video. It is one of the most concise, easy to understand videos that I have seen. No wasted time with voice instructions. The finger pointing and clarity of you camera make this instruction very good.

@MrSubaru1387

10 жыл бұрын

Thanks, glad you liked it and it was helpful to you.

@MrSubaru1387

10 жыл бұрын

Danny Cannon Glad I could help.

Bad ass homeboy! Fixing my son's truck this weekend!! THANK YOU

@MrSubaru1387

6 жыл бұрын

You're welcome 👍🏻

Just used your method to change out the fuel pump on my '96 Ram. Thanks for posting this video !

@MrSubaru1387

9 жыл бұрын

Great! Glad I could help.

Thank you for providing such a simple and fast method to gain access to the fuel pump. There are too many youtube videos showing idiots cutting an access panel in the truck bed floor. They also show cutting the structural reinforcement beams and destroying the bed. Your tilt lift method is quick and the truck bed is not destroyed.

@MrSubaru1387

9 жыл бұрын

Glad to help.

@frigglebiscuit7484

5 жыл бұрын

the first gen rams dont have s reinforcement in the area.

Thanks for showing it could be done this way, because I was thinking about doing or trying to change my pump this way and never heard of doing it like this and searched if anyone else did it like this and worked, great minds think alike and once again thank you for a great video 👍

Great video, just did the same repair today with success! Thank you!

@MrSubaru1387

8 жыл бұрын

Awesome, glad to help.

excellent video. one man operation,45 minutes. had to drop the spare tire.thanks for the video.

@MrSubaru1387

10 жыл бұрын

No problem, glad it was helpful to you.

This is the right way to do this job instead of lowering the tank. I’ve done it in 30 minutes.

Just like everyone else said, great video!! Thank you for making it look so easy.

Thanks for this. There are several good videos for this project but I found this one the most helpful. I ended up tilting the bed with a floor jack and a length of 4x4 wood post and supporting with 2 jack stands on a 2x8 piece of wood on the cross brace.

@MrSubaru1387

9 жыл бұрын

Glad to help.

I used this video as a reference when I replaced my fuel pumps. Great video thanks!!!!!

@MrSubaru1387

9 жыл бұрын

Glad to help!

Excellent directions. Straight to the point.

@MrSubaru1387

10 жыл бұрын

Glad you found it helpful.

Please make more videos of dodge repairs! Best tutorial video I've ever seen for my truck

@MrSubaru1387

7 жыл бұрын

+Maria Elena glad you liked it.

My man, just the video I wanna looking for, much appreciated

El mejor video que he visto en mi vida. Sin palabras pero bien explicado

Best video i have seen so far THANK YOU! Great job.

@MrSubaru1387

6 жыл бұрын

You're welcome. 👍

the best video i seen on here on how to replace a fuel pump on a dodge ram,most of these guys on here just like to here them selfs talk

@MrSubaru1387

8 жыл бұрын

+fabian bell glad you enjoyed the video. 👍

@Mr105246

8 жыл бұрын

it was very helpful man,thank you if you could i wanted to know is the bolts attaching the bed to the frame are in the same place on a 2002 dodge ram 1500 single cab

@MrSubaru1387

8 жыл бұрын

+fabian bell should be similar

@Mr105246

8 жыл бұрын

if you feel comfortable calling me please do so i had some question 702-439-8516

when lifting the bed up leaning toward passenger side... put a standard car jack under the bedframe where your tire wheel is located, you wont need a engine lift if you do that ...it works great

@ew20asent

9 жыл бұрын

Can you explain this method a bit more sound like a better way ? tx Alex

@Beach5289

6 жыл бұрын

I believe what he's describing is vs tilting the bed front to rear you tilt it side to side. Remove all the bed bolts on the drivers side , loosen all the ones on the passenger side 1/2 way , disconnect the filler tube , and lift the drivers side of the bed.

@h-townshortstop2636

5 жыл бұрын

Awesome tip. Thank you

@itsok865

5 жыл бұрын

Yup

@h-townshortstop2636

5 жыл бұрын

So I replaced mine yesterday. However I got a friend to help me just lift the bed and slide it away from the cab about 2 feet. It seemed much easier than dropping the tank.

Well screw laying on my back...this is way easier thanks for the video

Thank you for this video. Definitely gonna try it this way next weekend!

@MrSubaru1387

8 жыл бұрын

Glad to help

Nice video I just did the fuel pump on my 1995 ram 3.9 and it was easy to do the job this way than to drop the fuel tank

Thank you. I recently purchased a Gen2 1500. Glad to see people out there take the time to help others by doing these videos. Maybe i don't understand the youtube space as why would someone not like something they get for free (the thumbs down views)?? Please keep it up.

@MrSubaru1387

8 жыл бұрын

+baz770 glad to help. 👍

Thanks! I'm doing this job this weekend. I have a small tractor to do the lifting. Should be a snap!

@srlwrence

5 жыл бұрын

You would've heard me talking to myself the whole time.

Muy buen trabajo y gracias por el truco de levantar la cama...no lo hubiera pensado

Just the video I was looking for is what I wanted to say, thanks

Thank you for a great How To video! Very complete with great written narative that got to the point! Your method worked perfectly .. Thanks again !

@MrSubaru1387

8 жыл бұрын

+Paul Bukowski glad to help

Wow, that was a brilliant idea. what a time saver. Thanks

@MrSubaru1387

6 жыл бұрын

You're welcome. 👍

Thank you for the instruction - it's perfect!

@MrSubaru1387

9 жыл бұрын

You're welcome. Glad to help.

Excellent video and thanx for passing this on.

@MrSubaru1387

7 жыл бұрын

+Kevin Steele glad to help.

Great job, you helped me big time! Thanks

@MrSubaru1387

8 жыл бұрын

+Willie Hopkins glad to help.

Thank you for this video. Not only does it look like your a great mechanic, but your video skills are some of the best I have seen on vehicle repair video's. If you are not making repair videos for Bently, Chiltons etc, you should be. Saved me a lot of time on my repair.

@MrSubaru1387

10 жыл бұрын

Thanks. Glad you found it helpful. Just a good ol jack of all trades. Photographer/videographer, former auto technician, current Snap-on tool dealer.

Great video, and thanks, I followed it step by step

@MrSubaru1387

7 жыл бұрын

+Nickonovitz White glad to help 👍

One of the best. If not the best mechanuc video on KZread. Dude even gives you time to read.

Great video! Thanks have to replace mine in the morning.

@MrSubaru1387

7 жыл бұрын

+J JZ Glad to help

I would suggest testing the fuel pump and watching for leaks before lowering the bed of the truck

Thanks for the video, you saved me some time sir.

@MrSubaru1387

6 жыл бұрын

+Sigtacops 19 glad to help!

I should show this to my dad. Hes gonna be pissed lol

Excellent video, thanks.

Well that was easy for you good job great video...

Fantastic job sir thanks for sharing

Thank you, great video.

@MrSubaru1387

8 жыл бұрын

Glad you liked it.

Relly good video and instructions.

@MrSubaru1387

7 жыл бұрын

Glad you enjoyed the video.

very helpful vid, thanks!

@MrSubaru1387

8 жыл бұрын

Glad to help!

Awesome video thanks for the help!

@MrSubaru1387

7 жыл бұрын

+KomeeK glad you enjoyed it. 👍

Thanks man your a lifesaver

@MrSubaru1387

9 жыл бұрын

Glad to help.

Nice! That was slick!

U MADE IT LOOK EASY...

Great Video , Thankyou very much

@MrSubaru1387

9 жыл бұрын

No problem, glad to help.

Nice video well done thanks man

@MrSubaru1387

10 жыл бұрын

Thanks, no problem. Glad you found it helpful.

There is an arrow on the bottom of the module that should be lined up in the center of the 2 notches on top of the tank when inserting the new module back into the tank.

Excellent video

@MrSubaru1387

6 жыл бұрын

+Ace Matrix thank you. 👍

thanks for the help great idea

@MrSubaru1387

9 жыл бұрын

No problem, glad to help.

thanks for this best video

@MrSubaru1387

7 жыл бұрын

+John Outdoors glad you enjoyed it.

Great how to video!

@MrSubaru1387

7 жыл бұрын

+816 Diesel glad you found it helpful.

you just saved me 605.00 that's what the mechanic wanted to change it.

@MrSubaru1387

6 жыл бұрын

+chris awesome! Glad to help! 👍

thank you

2 hours start to finish. large fuel tank. full when pump failed. 4 beers later job done! Borrowed a friends successful 4 bay shop after business hours, he can't believe it.

Great How-To video ! ANyone have tips on how to raise and lower the bed without using an engine hoist (don't have access to one).

@Wythegoodsense

9 жыл бұрын

Katmandu2 You can rent them if available in your location.

@Shags306

9 жыл бұрын

Katmandu2 Chain hoist and large tree limb!

@criticalreasoning2129

9 жыл бұрын

Katmandu2 Use a tall farm jack on each side. Use old rug scraps to keep the jacks from scratching the paint. Or use a floor jack with a long stick on each side. If you only have one jack, you have to alternate from side to side and use lots of shims.

It’s like some asmr video with the glove noises. Eeek!!!

great jod dude.

ow my goodness.it took hours to drop tank,my son and I bought a parked litl d1500.,we had to pull tank out completely because it set up for a year we no of.lots of syrupy oil in pan.we were worried because dipstick was broken off,but handle was in tube.what we could c was attached to handle was rusted an broken off bout 6inches down.no idea on the rest.we were going to change oil n filter naturally.we had to drop oil pan to b sure.no rusty dipstick nside,hee haw we kikin now.cleaned wiped replaced gasket,all's great.back to fuel pump.we scowered the pik n pulls,no luckstill lookin for new one now.I love those places got mirror for my ford sport,also stay ups supports for hatchback glass lid andoor.also got support for hood,no more pvc pipe.stepping up in the easy life.had ford for 14yrs yus got little things.227,000 miles purrs.yes I'm a ford lady.anyway,wish we,d come across ur page bfor we started.got you now.b check-in as we get back to tank and filter.thanks for the close ups easy steps.have a good one.debbi

OMG UR AMAZING!! AWESOME VIDEO!! THANK YOU

@MrSubaru1387

6 жыл бұрын

You're welcome 👍

Charley Chapman of auto mechanics!!!!

Hey great vid ,

@MrSubaru1387

9 жыл бұрын

Thanks

You tha man!

One to things I liked about this video is the LACK commentary, BS'ing. Great video editing! One of the best I've ever seen ? How did you learn to do this ? Another is your great patience doing the job. I'm very impatient and cussing the whole way through working on cars! Lol! I need to learn patience! Lol!

@MrSubaru1387

9 жыл бұрын

Thank you. We'll I'm an ASE certified tech turned Snap-on tool dealer with an avid photography/videography hobby. It all just fell together. Lol

Very very helpful video. Thanks !!!

@MrSubaru1387

7 жыл бұрын

+Kristopher K glad to help 👍

GREAT VIDEO, YOU REALLY HELPED ME OUT, I FOLLOWED YOUR DIRECTIONS TO THE T. If I had my truck is on E & wont crank, do I need to fill up & try again

@MrSubaru1387

9 жыл бұрын

It won't crank or won't start?

@MrSubaru1387

9 жыл бұрын

If it's on "E" put some gas in it.

So as I've been reading some of the other comments I noticed ppl mentioning tilting the bed from the side instead.. is it easier to do a side lift and if so can someone explain the difference with which bolts to remove plz?.. I've also noticed in other videos when ppl have lifted just the frt that the bumper gets tilted should anything else be loosened or unbolted?

thank u!!!! im about to save $1,000 or more

@MrSubaru1387

8 жыл бұрын

Glad to help.

Very good video !!!😂

Great video- I have a leak and need to find where its at. Thanks

I am getting ready to swap beds on 99. I guess I should swap out fuel pump/ module.

I wish I could do it this way but I gotta drop the tank and clean it out. Been sitting for 3yrs with like a 1/8 of a tank. Runs when you hit the tank with a hammer lol

Thanks for sharing. Do you know what size this tank is? The pumps are apparently different for the 2 different size tanks. The 1 I'm working on is the 5.9L I think. Thanks, take care.

this help me replace my fuel pump on my 95 ram, my truck is hard to to so i replace my power steering gear box on the 96 ram, but it still is hard to Turn, does these trucks have a Fuse or a relay for the Power steering?

And people laughed at me hahaha been doin this for years Its so easy