Here i rebuild, paint and install my trailing arms for my E46 330ci Also installed is the rear anti roll bar and new endlinks
Жүктеу.....
Пікірлер: 14
@dmytrogoncharuk67107 ай бұрын
🔥🔥🔥🔥🔥🔥
@googlebad35407 ай бұрын
use grease on thread pullers and pushers
@budrobadre9 ай бұрын
So statisfying! Planning to take care of my own 330ci's underside too
@OEMplusRESTO
9 ай бұрын
Thank you❤️ Its not super hard just very time consuming really so i vote yes. If its in decent shape your 330ci wilm have reached a point where it wont drop in value ever so why not
@iain4853 Жыл бұрын
Great job Tim. It’s looking good. Would love to do this to my ci👍🏼
@OEMplusRESTO
Жыл бұрын
Thank you. Hope youre having a great day:)
@ivanfilipovic3296 Жыл бұрын
whoa and please take care/note/double check that rtab bushing should be torqued when car sits with its weight on ground and that pocket should roughly be put in place so it is in line with rear hub, so when suspension isn't loaded, the bushing is in its neutral state, if you hit bump or hole and your suspension moves + - 2 cm down or up, it makes a twist on bushing and if you installed it wrong so it's allready preloaded in neutral state you will effectively be "bottoming" bushing out and breaking it very early. I have had "proffesionaly" redone rear end of my 330ci and after short time i'm doing everything again since everything tore apart quite soon after rebuild.
@OEMplusRESTO
Жыл бұрын
Thanks for the tips ivan:) i appreciate it. i did torque it all with the suspension loaded imo. Not 100 percent accurate as i would have had to install a wheel first to be sure. But on eyesight instead.
@micheskillz
2 ай бұрын
@21:27
@ivanfilipovic3296 Жыл бұрын
how do you remove handbrake cables from trailing arm?
@OEMplusRESTO
Жыл бұрын
They were seized stuck. Had to cut them when removing the trailing arm and then wiggle them up and down, side to side, while spraying wd40 into the bore whey they sit in teh trailing arm, Until they gave in and came out
@PowerslideSWE Жыл бұрын
Capitol of Sweden hahaha, made me spit out my Pripps Blå hahahaaa. What's the going rate for a 6-speed 330 ci in Denmark? Can't find even one that isn't overpriced all to hell in Sweden atm. The car is gonna be fantastic, underside looks great.
@OEMplusRESTO
Жыл бұрын
:) Mine isnt original 6speed. The previous owner converted it to a 6speed, which i appreciate alot tbh. Much nicer car that way. And i have never seen one for sale in Denmark that was an original 6pseed either. I think out stupid registration tax make them rarer than hens teeth. And thanks for the kind words Never have tried a pripp blå. How dors it compare to the danish tap water also called carslberg?
@PowerslideSWE
Жыл бұрын
@@OEMplusRESTO I'd say that Pripps blå in that case is the same, tapwater more or less :D
Пікірлер: 14
🔥🔥🔥🔥🔥🔥
use grease on thread pullers and pushers
So statisfying! Planning to take care of my own 330ci's underside too
@OEMplusRESTO
9 ай бұрын
Thank you❤️ Its not super hard just very time consuming really so i vote yes. If its in decent shape your 330ci wilm have reached a point where it wont drop in value ever so why not
Great job Tim. It’s looking good. Would love to do this to my ci👍🏼
@OEMplusRESTO
Жыл бұрын
Thank you. Hope youre having a great day:)
whoa and please take care/note/double check that rtab bushing should be torqued when car sits with its weight on ground and that pocket should roughly be put in place so it is in line with rear hub, so when suspension isn't loaded, the bushing is in its neutral state, if you hit bump or hole and your suspension moves + - 2 cm down or up, it makes a twist on bushing and if you installed it wrong so it's allready preloaded in neutral state you will effectively be "bottoming" bushing out and breaking it very early. I have had "proffesionaly" redone rear end of my 330ci and after short time i'm doing everything again since everything tore apart quite soon after rebuild.
@OEMplusRESTO
Жыл бұрын
Thanks for the tips ivan:) i appreciate it. i did torque it all with the suspension loaded imo. Not 100 percent accurate as i would have had to install a wheel first to be sure. But on eyesight instead.
@micheskillz
2 ай бұрын
@21:27
how do you remove handbrake cables from trailing arm?
@OEMplusRESTO
Жыл бұрын
They were seized stuck. Had to cut them when removing the trailing arm and then wiggle them up and down, side to side, while spraying wd40 into the bore whey they sit in teh trailing arm, Until they gave in and came out
Capitol of Sweden hahaha, made me spit out my Pripps Blå hahahaaa. What's the going rate for a 6-speed 330 ci in Denmark? Can't find even one that isn't overpriced all to hell in Sweden atm. The car is gonna be fantastic, underside looks great.
@OEMplusRESTO
Жыл бұрын
:) Mine isnt original 6speed. The previous owner converted it to a 6speed, which i appreciate alot tbh. Much nicer car that way. And i have never seen one for sale in Denmark that was an original 6pseed either. I think out stupid registration tax make them rarer than hens teeth. And thanks for the kind words Never have tried a pripp blå. How dors it compare to the danish tap water also called carslberg?
@PowerslideSWE
Жыл бұрын
@@OEMplusRESTO I'd say that Pripps blå in that case is the same, tapwater more or less :D