dynamite .19 break-in and what a struggle it was
@Nitro_rc_life #nitro #rc #nitrorclife
I know it's a long video but I have never struggled with an engine like I did with this one thanks for watching
music by www.bensound.com
@Nitro_rc_life #nitro #rc #nitrorclife
I know it's a long video but I have never struggled with an engine like I did with this one thanks for watching
music by www.bensound.com
Пікірлер: 46
It's not gravity fed, the engine is the fuel pump. Nice though, everyone loves a new engine 😁
Baby Nitro!!! So much cuter than baby Yoda! Both are guru prodogi
@Nitro_rc_life
Жыл бұрын
Lol hell ya my dude
Awesome job buddy, we gotta beat the breaks off that this summer. Give RPM a run for their money
@Nitro_rc_life
Жыл бұрын
Of course this truck will be punished for looking so good
Cool video and engine,I like my dynamite.19, seems like everytime I run it,it gets a little more power,I would buy another one, little man is cool, next nitro gang generation.
@Nitro_rc_life
Жыл бұрын
He is just as obsessed as me
@CrazyDad226
Жыл бұрын
Yes all my dynamite engines the more tanks of nitro the better they get! I stopped running all my factory TRX,s and replaced all with Dynamite .19s . Love them . Out of 10 dynamite .19 i got only one that came new with a bad carb. Needles and seals everything looked good just wouldn’t prime or run. Put an sh slide carb on fired right up. Then i ordered a new dynamite .19 carb for it. When it came in i replaced it . Have a great day guys! Lets make nitros great again. Everyone keep running rich and loud!❤😂😊
me and my dad broke in this engine about a year ago and at the start the needles were messed up. once we found the right setting it worked great, the truck runs great with this engine a year later. good luck with it!
Holy shit man that looks so familiar to my .19 struggle man.
I’ve tuned loads of nitro engines, never once have I worried about engine temperature, ambient temperature or tuning for conditions. Neither have I had to change glow plugs. The engine tells you what it needs, if it chokes out at full power then your high speed too lean, don’t worry about idle or low speed settings until your HSN is set. Have a watch of JQ racing engine tuning tutorial on you tube. It is hands down the best tuning vid on the internet. Watching that video improved my understanding.
@Nitro_rc_life
Жыл бұрын
I've watched it several times. I don't tune by temp but I do like to check just to make sure I'm not cooking it
❤😂🎉😢😮😅😊. ไฟแอดพ์. ? 0:33
Yeah I had a hell of a time getting mine to run good. Didn't help that the factory carb settings were so far off and the manual didn't even list the correct carb. Managed to get it to run reliably in the end and used the same needle settings on another one I bought. Second engine was so much easier. I think for base settings I did 2.5 turns on the HSN and 4 or 4.5 turns on the LSN. Then just slowly started leaning it out as I progressed through the break in. With the factory needle settings, fuel couldn't even get to the carb. Also, both leak from the exhaust outlet with the Traxxas exhaust header. I wish THS still made exhausts for the T-Maxx and Rustler since they use standard 1/8 exhaust gaskets instead of the small o-ring Dynamite provides.
@Nitro_rc_life
Жыл бұрын
It has a ths exhaust but I'm thinking it's got too big of a stinger for the .19 I have a few others to try out there will be a video on that
@Nitro_rc_life
Жыл бұрын
Also the exhaust isn't 8th scale it's 10th you would need some type of adapter fir the tmaxx to run 8th scale
@CrazyDad226
Жыл бұрын
I no right! Dynamite.19 love the THS header and pipe. I have been on there web sight i think they might of never opened back up after the pandemic! ❤😂😅😊
@Nitro_rc_life
Жыл бұрын
I just got an order from them about 2weeks ago he is only selling what he has in stock
@CrazyDad226
Жыл бұрын
@@Nitro_rc_life thank you for the info. I love both my THS header and pipe. Thanks again. I havnt been on the web sight in a few months
I never had to do much of anything when breaking in a nitro hsp that’s it
Love this vid. So you think it was the combination of everything…. I was thinking of dropping this in my Revo later or the OS… How she running still….
@Nitro_rc_life
2 ай бұрын
Engine runs great and these run super hot during break in just like os21 those run hot aswell
Your truck will lean out when tank of fuel goes under half lean out will raise temps run it it's breaking in they do weird shit.
@Nitro_rc_life
Жыл бұрын
Now that it's close to a half gallon it's running perfect but still using the r5 plug it comes with a r3
Theres an air leak there guy. You haven’t messed with these very much have you? The leak is in your glow plug. I used very tiny silicone o’ring to put on the glow plug after I put the copper ring on. Fixed! These engines don’t break in like other engines. They take more time. Plus that engine needs to stay at a constant 215 for break in. Never rev your motor at all during the first 4 tanks, ever. On tanks 5 and six you run the idle just a little higher, not much and small revs like quarter throttle. Also on five and six keep the temps up, 215 like I said. After that run it on the ground and start leaning it out until you get it where you want. Then you can set your bottom end. Do what iI said on this engine and it will turn out to be one of the best, longest lasting engines you have ever had. Your inexperience really shows. People give these motors a bad name because they don’t understand them. The O’ring thing I told you about is just for this motor if your leaking fuel from around the glow plug. You should have just let it idle, not trying to rev it on the first 4 tanks. If you do everything I said with your heat cycles exactly like I said for any engine, they will last you so long it will blow your mind. Providing you know what you are doing with your tuning. Even on your 7th tank when finally hitting the road, preheat the engine. You need to let it cool all the way before the next one. This engine starts the first time every time. German designed, great engines.
@SLC_nitro
8 ай бұрын
@terryshrives8322 No offense to a Dynamite motor. The problem with this motor (later discovered) is the back plate is trash. And is 99% of the time the source of an air leak on a .19 . And he does know nitro.. well! Has many. Seal it up and runs good. Not sure about sealing the glow plug
ill bet next time you break it in on a bench then install. cold outside weather doesnt help either. nice motor.
@Nitro_rc_life
11 ай бұрын
Yeah I'm just not a fan of these dynamite engines I wouldn't buy a second
Less likely to over heat during break in if doing in the cold. Some adjustment will be needed once its warm weather but thats okay.
@ShadowOppsRC
Жыл бұрын
They run warm during break in anyways so I prefer to do it when its cold out side.
@Nitro_rc_life
Жыл бұрын
This motor was acting way strange I know I was tuned rich but at idle the temps just kept climbing regardless of needle settings the colder plug did the trick thankfully
@ShadowOppsRC
Жыл бұрын
@@Nitro_rc_life they can be a pain sometimes when new and super frustrating. I know my sh 21 I am breaking in loves to idle high. Some engines do that.
@ShadowOppsRC
Жыл бұрын
My dynamite 28 was hard at first but once I got it broke in it runs great and super easy to start.
@Nitro_rc_life
Жыл бұрын
That's good to know my other motors no issues they ran and broke in easily so I'm glad that's it's not me doing something wrong
Your video presentation was nice but when you explaining what to do to the vehicle, it’s always out of the frame when you’re making adjustments. I like what I saw but next time let people see all of the adjustments that you were making, but you’re telling the baby to stay out of focus when you don’t even have the vehicle in the frame, I’m gonna give you thumbs up for trying
@Nitro_rc_life
3 ай бұрын
I'm no professional just having fun!!!!
Want u start the engine is auto head the head ready.. Tq new user
@Nitro_rc_life
Жыл бұрын
I use the traxxas ez start with a glow wand it's an awesome system and can be adapted to other motors with a little modification
@newmark8631
Жыл бұрын
@@Nitro_rc_life I have a really good tip for you especially if you like using the ez-start system. Here is the thing, keep using the ez-start to crank your engine but i'm not recommending you to use the glow igniter and the crank motor at the same time. Bc when you do that start motor almost uses the whole electric and sometimes that causing to problem which is glow plug not glowing enough to ignite the nitro inside. and solution for that, plug out the wire caming from ez-start to the glow plug. and buy a separate glow igniter and use that. That's gonna make starting the engine almost %50 easier (excuse my bad english, i'm from Germany.)
My dynamite 19 was absolutely terrible fir my Tmaxx as well. I just took it out and sent it back to them and received a full refund.
@Nitro_rc_life
11 ай бұрын
Ya I tried to install some ceramic bearings and since then the motor never ran correctly so it's in a box