Your hub was fine take some scotch bright get as much corrosion off as possible and use a good about of high friction grease reinstall you said it yourself the bearings were spinning fine that's all that matters

@MotoGarageTV

5 ай бұрын

Yeah, I cleaned it up and sold it on eBay for close to what I paid for the brand new one. It will worked out. Thanks

I removed my hub from a 2012 MTS,it looked exactly the same as yours, horrible(only 16k miles). I cleaned it up best as I could but it will get replaced the next time i get new tires.

@MotoGarageTV

8 ай бұрын

It's odd that they get that way so fast. Almost like they weren't properly greased at the factory.

👍

I bought bearings for 230 Euro's and replaced the ones in the hub myself. Maximum 2 hours of labor and wayy cheaper

@MotoGarageTV

3 ай бұрын

That's the route I was going at first, clean the hub and replace the bearings. However, I could not get a hold of a bearing set through Ducati. I believe I found an aftermarket set on Ebay, but I did not want to risk it and went with buying a new assembly. Then I cleaned up my old one, repacked the bearings and sold it on Ebay, and got the majority of my money back.

@PyroMania61

3 ай бұрын

@@MotoGarageTV Don't get it through Ducati tho.. don't think they would be keen just to sell you the parts instead of the whole thing. Here are the part numbers you need for the hub: - 1x BAH0175-SKF (bearing) - 1x RNA4910-2RS-SKF (bearing) - 2x OAS-58X72X6-NBR (dust seal) And these are the parts for the swingarm pivot: - 2x HK2520-2RS-SKF (bearing) - 2x 6005-2RSH-C3-NSK (bearing) - 2x BD-25X32X4-NBR (shaft seal)

Using a plastic bag on the rear axle nuts looks a good idea. My impact drive left a few marks. I don't have a hoist, so could I put a scissor jack table under the exhaust when I remove the rear paddock stand? Great video.

@MotoGarageTV

Жыл бұрын

Yeah, the bag is thin enough to fit over and protect. Sometimes I use a blue shop paper towel. They work pretty well.

@grahambrown5874

Жыл бұрын

@@MotoGarageTV Do you known if scissor table under exhaust is safe to safe to support rear end?

Do u prefer to use that pipe with a regular rear stand , instead of single sided rear stand ?

@MotoGarageTV

Жыл бұрын

To me, it's more stable. I have a Bursig Stand that the bike is usually on. But while on the lift i have a better piece of mind with the pipe and a regular rear stand

If the axle should be able to come out of the hub is there any need to undo the pinch bolts? I ask because I need to replace the rear disc.

@MotoGarageTV

Жыл бұрын

You shouldn't have to undo the pinch bolts. For me, I figured something was preventing my axle from sliding out, and I figured it must be the pinch bolts.

Hey What were the symptoms you were getting that lead you to replaced the hub

@MotoGarageTV

6 ай бұрын

I was trying to remove the axle to replace the brake rotor, and that's when I noticed a problem. The axle was seized inside the hub.

@lennykibbs260

6 ай бұрын

Oh ok, thought maybe you had a weird vibration or something that caused you to change it out

@MotoGarageTV

6 ай бұрын

@@lennykibbs260 no, rode fine,I wouldn't have spotted the issue of it wasn't for trying to pull the axle.

@lennykibbs260

6 ай бұрын

@@MotoGarageTV gotcha-

Uhhh ummm ummm uhhhhh uhhhh uhhhh

@MotoGarageTV

5 ай бұрын

LOL... I'm glad you watched the whole video and captured all the uhhh and ummm's.