🔥 Drywall partition ▶︎ How to Build a metal framed wall 💪 PLADUR
🔥 Drywall partition ▶︎ How to Build a metal framed wall (70mm profiles)
👇 👇 👇 👇 👇 👇 👇 👇 👇 👇 👇 👇 👇 👇 👇 👇 👇 👇 👇 👇 👇
• 🔥 Drywall partition ▶︎...
🔵 Guide to help you analyze the budget: www.tutorialcreativo.com/guia
Tools we usually use:
- One level: amzn.to/3BgU8cD
- Laser level: amzn.to/3rGZqK2
- Laser level: amzn.to/3rGUQeD
- A pen: amzn.to/3rmnLVu
- One meter: amzn.to/3etCB7h
- A cutter: amzn.to/2VS7xrb
- A pencil: amzn.to/3zbzI2P
- A drill: amzn.to/36IMtFJ
- 5 Bit: amzn.to/3eRsU2P
- A screwdriver: amzn.to/3exW4nm
Studs and channels for interior
Its composition is galvanized steel type DX51D and galvanized Z140 or Z275 that make up the framework of the load-bearing structure of partitions, cladding, shelves, shelves and drawers. The C-shaped profile that is installed in a vertical position and that fits inside the channel is called a stud. The U-shaped channels constitute the horizontal element that is fixed to the floor at the top and bottom. Both profiles have a knurled aspect that ensures the fit. The uprights have notches or H-shaped openings in their soul that facilitate the passage of installations, for example electricity, plumbing...
There are several sizes but the most used are the 48mm and 70mm uprights and channels.
The uprights, despite the fact that when we work we use the name 48 or 70, one thing to know is that they always have a millimeter less than the channel so that they fit well inside it. For example, the 48 is 46.8mm wide and the 70 is 68.8mm.
These profiles are also used for mounting ceilings, especially when you don't have many options to hang from the floor.
Plasterboard plates:
These plates are composed of a plaster core with additives and covered on both sides with a sheet of cellulose. Its manufacture is carried out through a continuous lamination process and according to the standard.
They have a visible face depending on the type of plate you need, it can be cream, green, pink, blue, yellow that allows any final finish. The hidden face usually has a brownish hue. To facilitate the treatment of joints, the longitudinal edges are tapered. The transverse edges are cut. But there is also a type of plate on the market that has all the sharpened edges.
Пікірлер: 77
Thank you so much ❤
I have used this video as a training video for my Mexican workers, here in mexico. We build low cost houses out of alternative materials...the usual is everything is concrete. Too hot and too costly now. This style of construction for small housing, reduces labor tenfold. I have 3 crews working. Have shown one crew this video and their work volume has increased many times over, even though they been working for us for two years. It is so basic in instruction, even Mexican workers can follow it and reproduce the quality and speed required to make this style of construction viable. They could not pick up the many other videos I showed them. Kudos bro. Well done!
@walterdiaz2003
Ай бұрын
Same in El Salvador. Hopefully someday we'll start using the technique in the video.
@ivanmillar7084
Ай бұрын
Hasta los maestros mexicanos pueden 😂
una duda, porque algunas veces atornillas el montane con la canal y otras veces le das con la el alicate manual?
Very efficient worker
Fantastique 👍
Hello friends I love his work I live in Mauritius I am working very hard all decorating home 🏡
How to purchase this light. Amazing.
I'm amazed, you're good!
Quem sabe sabe até parece fácil parabéns
كل الاحترام دام عطائك رائع وجميل
This is the "like there is no tomorrow" style of construction, it is very fast and effective, if there is no tomorrow...
Hello Christian, I was just wondering the name of the tool you've used @7:00?
God job...
Hi, where I can get the tool crimper that you are using it ? Please?
Can you share the plan ? Greetings here from the philippines . Thank you
excelente material, consulta, las vigas que medidas tiene de largo, el ancho y que medidas de drywall, muchas gracias.-
Молодець 👍👍
Subscribed na lods thanks for sharing dinownload ko na🤭🤭
Cristhian, muy buenos video. Es factible construir una casa entera de una panta (80m2) con perfiles de 70 y un techo liviano. Saludos
@mendozadurlock1092
8 ай бұрын
Hacelo al estilo Steel Framing no escatimes material que es más recomendable
Berry 👍
👏👏👏👏👏
travailleur good
W 7.52 ciecie pod katem 90 stopni - trzeba bylo zrobić pod katem 45 stopni wtedy poprzeczka zachodzilaby na pionowe profile gdzie byś mogł dodatkowe polaczenia zrobić
Always watching from Philippines 🇵🇭🇵🇭🇵🇭👍👍👍👍
W 2.40 błąd, najpierw było płytę przykręcić a na nią dopiero profil od ściany. W twoim przypadku będzie brakować później do czego przykręcić płytę na bocznej ścianie co widać w 12.05.
@konstantinosmatsangos9594
8 ай бұрын
1A
same panel door i have my house in thailand, haha
Interesting & many thanks for sharing your talent and experience. I noticed @1.52min a u channel splice is introduced. I wondered why IRC21, R603.3.5 Splice recommendation (~160cm overlap with 4-#8 screws on each side) was ignored. Inspectors might not be as accepting.
@fleaniswerkhardt4647
9 ай бұрын
160cm or 160mm?
@mendozadurlock1092
8 ай бұрын
En latinoamerica ni vienen los inspectores 😅
@sqnhunterx
Ай бұрын
Inspectors??? What are they??? None down south here!! 🤣😋😁
👍👍
👍👍👍👍👍
Disculpa como puedo conseguir las piezas para Fijar los metales
@sabljarka1158
Жыл бұрын
En holandes se llama Fixeer tang, no se como se dice en espanol
Wow, a collating screw gun would have been nice?
Cool music Who?
😊👍
I like music, who sings
😍😍😍❤❤💕💕
Why didnt he screw the studs at the top? What did he do with the puncher tool…? And why?
@feralbigdog
Жыл бұрын
it would be nice if he gave explanations, and the numbers in it
@markgrabowski8662
2 ай бұрын
This tool punches and compresses tabs to hold both railings/profiles together like screw does where is accessible
viel zu komplizieret gemacht. viel zu viel unnotiges material verschwendet . cd profiele werden nicht mit tex schrauben befestigt dazu gibt es zangen wegen delatation und und und
เลเซอร์ผนัง
Супер е видеото, но съм чел, че където е вратата, трябва да се направи "пета." Тоест профила който е по земята се сгъва на буквата Г и за стърчащия край се фиксира профила който е вертикален.
this guy do not use safety glasses,it is very dangerous
Could do without the music, otherwise ok video
Manufacturer of intelligent manufacturing equipment for light steel structure buildings Foshan FrameMac Technology Co., Ltd. (FrameMac) is a professional light steel structure building intelligent manufacturing equipment manufacturer in China, providing a fully automatic light steel building frame production solution integrating software and hardware. The "FrameMac" solution realizes the seamless connection of "end-to-end" production from CAD architectural design software to production processing, construction and installation. FrameMac light steel equipment source factory
I always lay the boards vertical not horizontal..Any reason why you do ?
@halilmurati9215
Жыл бұрын
Wrong
@cesarcacayan6916
Жыл бұрын
Horizontal boards are more#stronger wiht alteranate joints
@carlrotheram3684
Жыл бұрын
Then the support spacing will need to be 50cm not 60cm.
@mattivirta
9 ай бұрын
normall drywall panels installed vertical because normal house height have same than sheet panel height, not need cut and lot lot less seam have, have lot less work at seam and strong.
@TheMakyato
9 ай бұрын
@@mattivirta drywall sheets come i various size and vary from place to place , there is no rule /law on how to lay panels , in the vid he fallow all the right steps
such houses are blown away by light hurricanes)
@hiidenwarrior2698
Жыл бұрын
Whewre did you learn your structural design? In the Tubold's University of Quiapo! Those structures were originally design and built by the US Navy in Guam, Marianas and other Super Typhoon belt! IQ 11!
@mattivirta
9 ай бұрын
same wood frame blow if hurricane go, lot better make hollow blog wall all outside wall, inside can make steel, lot cheapen, wood or hollow block wall have same price, wood have expensive and burn easy. wood have worst material today at house.
Тот случай, когда инструмент и одежда сразу показывают, что работает самоучка, а не опытный и аттестованный специалист...
Sie haben mehrere Fehler gemacht
@nyaribernadett4579
Жыл бұрын
exakt
Bros, I respect all hard working trades but what the heck did I just watch? I've been doing serious drywall and steel stud videos on KZread for 6 years and got half your views.... wtf?
Pusch ist das einzige richtige Wort.
Qqqqq
worst and totally wrong make drywall sheet horicontal, lot seam and lot more work than vertical. sheet have standard dimensions perfect to height and wide to drywall not need cut any.
@markgrabowski8662
2 ай бұрын
Cross-bracing for rigidity/ added structural strength (common sense)
It is for plastering good, for tape and joint doesn't work
👍👍👍