3 years ago and still helping thank you.

Thank you! This is how instructional videos should be presented, straight to the point and actually works! Nowadays most instructional videos are filled with too much blah-blahs only to end up not being helpful at all.

Nice tips. Couldn't have open the drum without ur video. I dont have the proper wrench.

I work in a sheet metal fabrication shop, and use 50 gallon drums of spray glue. I use a Stanley Wonder Bar to remove the bung. Any pry bar about an 1-1/2" to 1-3/4" wide should do as it only needs to contact one of the inside tabs. The other edge will brace against the bung. Just stick in the bent end, twist, and the bung spins out easy, peasy, no 2 handed coordination required.

Nice! I thought it was something "right under my nose" in a way. Got 30 liters of ethanol I need for the lab but of course nobody bothered finding those tools to unlock them with. But I do have screwdrivers and non-tools that are similar. Good to see it demonstrated to avoid some potential messy mishaps.

4 years ago and still helping.... I must say u made it look like the threads were all buttered up

Thank you, i wanted to see what is the correct tool, and the DIY way. Short and fantastic.

Awesome!!! I was struggling for a hot minute!😅

@haroonharoon6925

2 жыл бұрын

Me too

Thanks for that - I couldn't have managed without it today.

Thank you ! This video was just what I was looking for.

Fantastic. Thank you. You’ve just solved a potentially expensive problem

Worked like a charm!!! Those people who gave you thumbs down can suck it!!!

Dude just became my hero

what a beast this was mad helpful thank you big dawg

thank you, i knew someone would have a "better" solution.

Not all hero’s wear capes 👍🏼

Very helpful. Didn't work out for me, but still helpful.

Thank you saved me so much time.

Thanks for the help! I really needed it! Great method!

Awesome and direct to the point!!

Thanks for your video. It was really helpful

Thank you so much for sharing your experience. ❤

Thank you. I was stuck with one of them, wondering how to open it

Genius! Huge life saver! Great solution.

Worked GREAT, thank you!

Thank you! This was very helpful!!

Thank you, exactly what I needed.

Thanks bbro im from Indonesia

Now I can get into my bung hole - thanks!!

Thanks 😊 philip

This just totally saved my A%* - thank you!!

You. Are. A. Legend.

Thank you 🎉

Concise. Perfect 👌🏾

So helpful. Thank you.

Thank you!

Thank you

Can you do the other small cap too? I have no idea how to open it except for with a pipe wrench, I always end up stripping it. :(

Dude an actual fucking life saver

Thanks so much

Thank you!!!

Great tip

Ty

brilliant

Wow thank you so much!

So... what if I have no screw driver???

Thanks boss

Muito boa ideia

I love you thank you

Genius

My man.

You have served KZread well. Or me at least

now i know where the term bung-hole is from :D

@jshepard152

7 ай бұрын

Uh huh huh huh huh huh...

omg thank you!

That's the bung plug. How do you remover the actual bung on the lid?

@PhillipSpring82

2 жыл бұрын

If you are referring to the bung cover, if metal, i usually grab one of the tabs with pliers. I like to pinch the tab horizontally and then put away from the bung, then up, then across. I find it easiest to use channel locks to make sure the doesn't sliver off. If that happens then you will need to use larger needle nose pliers to just brute force rip it of.

God’s work

Thank you! Did not want to invest in the tool!

Helpful 😛

What about the small vent cap? How do you remove it?

@PhillipSpring82

2 жыл бұрын

Apologies for the late reply. Depending on how tight the bung has been torqued you will require different tools. If it has been torqued to hazmat shipping specs you will need a legitimate bung opening tool. If it is just a general tight I have used large sized channel locks to loosen that bung. Normal pliers will not be large enough. If you go this route make sure the thickness of the channel locks is close to the opening size of the bung.

If you have heavy duty gloves you may want to wear them I got a minor cut nevertheless be prepared!

Thank you 😂

Baaaammmnn!!

Bung bandit.

Thanks to you!! I made it hahahahah 😆

🫡