Thank you for making this video. I learned more in your 11 minutes than in my 3 hour shop class . Actually 2.5 hours with breaks ! Also hard to learn with 6 guys and instructor crowded around machine. Only my 2nd class on the Doosan. I didn’t know about that eye sensor. We did touch off holding a scrap of paper between the workpiece and cutting tool. It’s hard to get the feel of the pressure to hold the paper with how close to set the tool . It will take experience. Already like .0006. off just with set up by feel would blow a job with tight tolerance . Nice to know those eyes are out there to take the guesswork out of the equation. Thanks again for making a video that is clear and you can actually see the control. You are very professional in your explanation and calm even presentation. Plus good example with proper ppe eye protection and work uniform.

@aaronrunk4209

Жыл бұрын

You are most welcome. My goal was to give a clear understanding on this machine setup. So many machines are different and having a video like this really helps. For more visits like this check out this page kzread.info/dron/awMg1dcdGS7K9aBIG2RGGw.html

Excellent video! I just purchased a used Fanuc controlled lathe and this video has been very helpful in getting up to speed with setup and operation.

Thanks for this video bro. I learned a lot. I started in this trade in January and have been loving every minute of it and I’m running this same machine every day. I appreciate the teaching bro. I’ll be honest when you dropped the tool presetter then closed the door and then referenced the machine I tensed up a little lol 😂

@derrickstefan7087

2 жыл бұрын

Instablaster

@aaronrunk4209

Жыл бұрын

Your welcome for the video. I enjoy making them fit others to learn from. If you want to see more of them you can see them here kzread.info/dron/awMg1dcdGS7K9aBIG2RGGw.html

Great video..I saw you dont publique new videos long time ago,I dont understand why. my english is realy poor but I really thank your way to explain every single move of this process. thank you for your time. hope you piblique one to know how to make a program on this kind of lathes.

Definitely one of the most comprehensive and explanatory videos on YT👍. Thank you for sharing this👌💛! This has made me definitely closer from my #Haas'ish understanding to #Fanuc'ish mastery if I can say so.

@aaronrunk4209

Жыл бұрын

It's very easy for someone to understand what's happening during a setup, not everyone has this understanding especially if they are wanting to learn. So making videos like these really helps others and that why I make them. If you want to see more like this check out kzread.info/dron/awMg1dcdGS7K9aBIG2RGGw.html

Thanks so much... From Greece (Here we call Tool Setter)

@unclerandy3784

3 жыл бұрын

@Hamza Kashton cringe

@aaronrunk4209

Жыл бұрын

Welcome

MTS representing!

Sir zoom nothing is seen which key are u using to operate

great job. write some programs, facing, od rough, drill, tap, od finish

@aaronrunk4209

Жыл бұрын

Great news i have lots of training and programming videos here kzread.info/dron/awMg1dcdGS7K9aBIG2RGGw.html

May i ask cost of machine like that, want have some idea. Thanks.

What about the workshift settings?

On our pumas they say q set

How old is this machine? Is there no canned cycle for tool setting? I see you manually moving the tool tip around and selecting the quadrants using numbers instead of visuals.

@aaronrunk4209

Жыл бұрын

This machine is from 2004 and is still very much useful and week continue to be if it's taken care of. That's why I made the video to help others when setting it up. Also, yes there are many canned cycles that run on this machine. I have videos of them here kzread.info/dron/awMg1dcdGS7K9aBIG2RGGw.html

hehe you wanted to say on a Haas lathe XD

Hallo bro . Please review GSK

What year is this Doosan Lynx 220?

Well done. Thank you for education. From Russia with frendship.

@aaronrunk4209

Жыл бұрын

Your welcome here's more kzread.info/dron/awMg1dcdGS7K9aBIG2RGGw.html

So when you set up that part again, because you save the program after the setup in the usb, will the tool offsets and geometry all be the same when you load it back up ? As in you won't have to touch off any tools ?

@ricardom4913

4 жыл бұрын

No. You have to touch off everything again

@F30586

4 жыл бұрын

Always have to touch off the tools

@brandons9138

4 жыл бұрын

Well you can out put the offsets as well as the program to the USB. I've never had the opportunity to really use this feature, as once you pull a tool out of the turret, the tool length is not going to be exactly the same next time around. So loading the saved offsets is kinda useless.

@aaronrunk4209

Жыл бұрын

Good news if you just setup the jaws and don't remove the tools your in good shape. Also, even if you remove the tools but load them in the same position you could dial then back in as long as they are pushed back against the stop or all the way into the turret position. It's still recommended that you touch them off again. To see more tips and Setup videos check them out here kzread.info/dron/awMg1dcdGS7K9aBIG2RGGw.html

buenas tardes cual es el codigo para descativar la alarma de la puerta gracias

@fvkthsstm8524

4 ай бұрын

en la caja que trae tiene los codigos pegados,donde estoy trabajando aurita es solo haas que tenemos y ganesh

Hello sir, Where do you write the tool high? Page?

@aaronrunk4209

Жыл бұрын

So this machine will have geometry but not tool height. Some machines do have this ability but is mainly used for conversation programming. Check out more here kzread.info/dron/awMg1dcdGS7K9aBIG2RGGw.html

Bro, is thier any option to check graph before run the job?

@aaronrunk4209

Жыл бұрын

There is a way using a graph, but you will have to lock the machine's axis with I believe code M17 and then run your program in auto mode. The spindle will run, and the turret will index, but X and Z will not move. On the graph, you'll see feed and rapid lines. Once ready to run unlock your axis with M18

Good job dude! How do you activate de Y axis?

@aaronrunk3352

Жыл бұрын

So this machine does not have a Y axis but it can ask do some cool stuff

@aaronrunk4209

Жыл бұрын

Here is a link to more videos like this kzread.info/dron/awMg1dcdGS7K9aBIG2RGGw.html

They use tool eye on mazak

HAAS is so much easier to upload and download a program from the USB, but I guess that's FANUC.

@max_eley

3 жыл бұрын

Fanuc is a plugin and cycle start on the CF card, the reason fanuc uses a CF card is because it is more stable and faster, i have used both machines and the cf card method is superior, fanuc has not yet developed much into usb. and there is no need.

This is why I hate Fanuc. Every single controller is a world apart, even in the same year product run. My doosan lynx controller is totally different.

@RacerX-124

3 жыл бұрын

Yeah that's the real issue with Fanuc. It isn't that they're "harder" to use, it's the lack of consistency. Going from a mid 90s Haas to a brand new one, it really isn't all that different.

@rastislavnad6548

Жыл бұрын

Check newest doosans with fanuc xD or newly DN solutions, its pre chaos and lagg :/

Where is your country sir??

Buenas tardes como está. Saludos desde Bogotá Colombia. Será que me puedes enviar todos los ciclos de ese torno Doosan ciclos de ranura de roscado desbaste en fin todo todos los ciclos de taladrado o si me puedes enviar programas con los códigos del encabezado o micelanios gracias

@aaronrunk4209

Жыл бұрын

The best thing to do if you would like to see programming videos is to check them out here kzread.info/dron/awMg1dcdGS7K9aBIG2RGGw.html

@aaronrunk4209

Жыл бұрын

Good news, I have a lot of videos with more of the info you are seeking.

I have an older Daewoo Puma without the "tool eye". Setup is so much easier. I just have my T0101 always set to 3.000. Then I face the part and work shift my coordinates to get T101 position to 3.000. If my tools were already set up off of that face then I am done. If not I use a gauge block and input my Z offsets for each tool. Diameters I have to turn and measure. This just seems more complicated for some reason,

@matt23727

3 жыл бұрын

Because you've never used it. A tool probe is 1000 times better

@S_V_C

3 жыл бұрын

@@matt23727 agreed, you can access tool offsets, (X and Z) alter rad's, alter workshift all in the offset page. I found it quite simple as an apprentice to pick up

You didn't really say anything about homing. You pushed buttons without saying anything.

@aaronrunk4209

Жыл бұрын

Sorry about that. I did miss this. I did touch base on these in my other programs.

Cuando está taladrando sale una alarma algo de hidráulica

@aaronrunk4209

Жыл бұрын

La alarma tendrá algo que ver con sus niveles de aceite. Asegúrese de que su máquina esté completa y vuelva a intentarlo.

Cómo puedo programar un ciclo de taladrado profundo

@aaronrunk4209

Жыл бұрын

You want to use a G83 canned cycles. Learn more about them here kzread.info/dron/awMg1dcdGS7K9aBIG2RGGw.html

This is my job 9 years ago other day One coworker know me cough a lot he gave me cough medicine but he lie he gave me the mental medicine I was not remember a lot of words and the boss go play to me then I quit job

And this is why I hate Fanuc!!!........so many key strokes and different pages and arrow across to do ...

I añmps forgot all about cnC lathes,, besides ,I'm making more money on construction.

And the award for the worst camera guy goes toooooo.

I hate fanuc😢